A cost effective, compact and reliable PWM drive for 1/4 through 1 HP DC applications The Micro 100 Drives have been designed with a Pulse Width Modulated (PWM) regulator to produce clean DC current to the motor. When compared to conventional SCR drives, the PWM technology provides a cost effective adjustable speed package that delivers the performance you need for a wide range of commercial, light industrial and industrial applications. The near unity form factor of the Micro 100 PWM drive is motor friendly. The clean DC current output of the drive allows cool, quiet motor operation with extended brush life. The performance matched Micro 100 PWM Motors are smaller, easier to maintain and more cost effective than comparable SCR rated motors. The improved form factor of the Micro 100 PWM drive also provides high, constant operating efficiency across the entire motor speed range. This not only reduces your energy costs but also provides a wider speed range for more precise drive operation. STANDARD FEATURES Open chassis construction on an L bracket for flexible mounting within the electrical cabinet. Fast switching Pulse Width Modulated (PWM) regulator provides: - Dynamic response to load variations. - Quiet motor operation for noise or vibration sensitive environments. Near unity form factor provides: - Clean DC output voltage from the drive to the motor. - Use of smaller, more cost effective motors in most applications. - Constant, high efficiency operation across the entire motor speed range reducing your energy costs. - Longer motor brush life reduces motor maintenance. All circuitry - sequencing, regulator, power and terminals - packaged on a single, surface mount design printed circuit board. Built-in surge suppressor helps protect semiconductors from line transients for better reliability. Electronic short circuit protection is provided by instantaneous output current sensing utilizing pulse feedback current limiting. 5K ohm speed potentiometer to vary the output speed of the drive. (Speed Pot reference models 1DN11050, 1DN11075 and 1DN21001.) 0-10 VDC isolated reference input models 1DN12050, 1DN12075, and 1DN22001. Jumper connections for horsepower selection. Application adjustments tailor drive performance to your needs: - Separately adjustable maximum and minimum speeds set speed limits. - Adjustable current limit protects machinery, wiring and drive. - Adjustable acceleration/ deceleration rate for smooth starts, stops and speed changes. - Adjustable IR Drop Compensation for improved speed regulation. 50:1 constant torque speed range. UL Listed and C-UL Listed to meet most electrical safety codes in North America. Performance matched Micro 100 PWM DC Motors in NEMA 34, 42 and 56 frames provide the application flexibility you need from a single drive source. Two years from date of manufacture/one year in service full exchange warranty eliminates troubleshooting and quickly returns you to operation. Analog DC Drives D4-1
Analolg DC Drives KEY INDUSTRIES & APPLICATIONS Industries Applications Automotive Actuators Electronic Blending Machine Tool Centrifuges Medical Chip Bonders Metals Conveyors Paper Metering Physical Fitness Mixing Physical Therapy Packaging Plastics Pumps Printing Treadmills Rubber Wafer Spinners Wafer Cutters X-ray scanner & tables X/Y Tables SERVICE CONDITIONS Elevation: Up to 3300 feet (1000 meters) Ambient Temperature: 32 o F to 131 o F, (0 o C to 55 o C) AC Line Voltage Variation: +/-10% of rated voltage AC Line Frequency: 48 to 62 Hz Atmosphere: Non-condensing Relative Humidity 5% to 95% APPLICATION DATA Service Factor: 1.0 (continuous duty) Form Factor: 1.07 Speed Regulation: 1-2% (95% load change) Speed Range: 50:1 Output Voltage: (115 VAC Input) 0 to 120 VDC, (230 VAC Input) 0 to 240 VDC ADJUSTMENTS Maximum Speed (percent of rated): 50% to 100% Minimum Speed (percent of rated): 0% to 50% Current Limit: 50% to 150% Accel/Decel Rate: 1 to 10 seconds IR Drop Compensation: 0% to 10% Motor HP 1/4 1/3 Micro 100 Drive Ratings Rated AC Line (amps) 115 VAC Input (Model Number) 230 VAC Input (Model Number) Input KVA DC Voltage Rated Current (amps) 3.7 0.43 120 2.0 - - - - 4.7 0.54 120 2.6 - - - - DIMENSIONS OF MICRO 100 DRIVE All dimensions are in inches (mm) MIN. MOUNTING CLEARANCE.63 16.0 mm 1.77 45.0 mm.75 19.1 mm 1.00 25.4 mm 3.125 79.4 mm 4.29 108.9 mm 3.82 97.0 mm 1.00 25.4 mm 1.75 44.5 mm.69 17.5 mm DIMENSIONS OF MICRO 100 HEATSINK KIT GROUNDING POINT SIDE VIEW 1.00 1.75 1.50 1.00.25 8.00 1.76 4.00.74 TOP VIEW 5.50 5.00.81 3.88 FRONT VIEW DIMENSIONS IN INCHES 2.02.80 20.3 mm 3.64 92.4 mm.80 20.3 mm M4 X.7 TAP (6) PLCS AS SHOWN.228/(4) PLCS 1/2 (1) 7.1 0.82 120 3.9 - - - - 3/4 (1) 10.5 1.2 120 5.8 4.6 1.1 240 2.6 1 (1) - - - - 6.5 1.5 240 3.7 (1) Drive must be mounted to a metal plate (18 x 18 ) to meet full horsepower rating. D4-2
A variety of cost-effective motors designed for PWM DC drive applications These permanent magnet single-phase DC motors have been designed for use with the near unity form factor Micro 100 PWM controls. When compared to conventional SCR drives, the PWM control technology provides a cost effective adjustable speed package that delivers the performance you need for a wide range of commercial, light industrial, and industrial applications. The clean DC current output of the drive allows cool, quiet motor operation with extended brush life. The performance matched Micro 100 PWM Motors are smaller, easier to maintain, and more cost effective than comparable SCR rated motors. The improved form factor of the Micro 100 PWM drive also provides high, constant operating efficiency across the entire motor speed range. This not only reduces your energy costs but also provides wider speed range for more precise drive operation. Micro 100 PWM Motors are available from 1/4 to 1 HP in standard NEMA 34, 42 or 56 frame sizes to economically meet your requirements. NEMA 34 AND 42 MOTORS Compact TENV enclosure ideal for tread mills, packaging equipment, material handling equipment, business equipment, medical equipment, machine tools, robotics, pumps, and conveyors 1/4, 1/3 and 1/2 horsepower NEMA 34 frame 3/4 horsepower NEMA 42 frame 155 degree C insulation Dynamically balanced armatures High torque-to-weight and inertia ratios Non-contact sealed ball bearings Low cogging torque M-8 Ceramic magnets Optional conduit box and brakes NEMA 56 FRAME MOTORS Designed for industrial environments for use on conveyors, mixers, blenders, pumps, and a variety of material handling equipment Available from 1/4 through 1 horsepower Class F non-hygroscopic insulation system is standard for insulation integrity and longer motor life Permanently lubricated doubleshielded ball bearings prevent dirt entry and guard against grease loss New cartridge brush holders with brass inserts and stainless steel springs ensure constant pressure on commutator for longer brush life. Holders can be easily removed for inspection and maintenance. Large external conduit box and permanently marked leads simplify connections for ease of installation. Analog DC Drives D4-3
Dimension Sheets for NEMA 34 and 42 Frame Motors NEMA 34 Frame Frame C NEMA 42 Frame E660 5.65 E675 6.77 E690 7.57 Analolg DC Drives NEMA 42 Frame with 56 C-Face D4-4
Dimension Sheets for NEMA 34 and 42 Frame Motors with Brakes and Conduit Boxes NEMA 34 Frame MICRO 100 Frame C E660 5.65 E675 6.77 E690 7.57 NEMA 42 Frame Brake Specification Coil Voltage: 120 VAC Power: 5.5 W Amps: 0.045 A Coil Winding: 2402 Ohms Brake Pickup Voltage: 90 VAC Max Dropout Voltage: 2 VAC Static Torque (min): 12 in-lb Speed (max): 3000 RPM Analog DC Drives D4-5
Speed/Torque Characteristics of Micro 100 Motors 100 NEMA 34 and 42 Frame 100 NEMA 56 Frame % CONTINUOUS TORQUE 80 60 40 20 CONTINUOUS TORQUE % CONTINUOUS TORQUE 80 60 40 20 CONTINUOUS TORQUE 0 0 0 20 40 60 80 100 0 20 40 60 % RPM % RPM 80 100 Dimension Sheets for NEMA 56 Frame Motors DIRECT CURRENT MOTORS AND GENERATORS INDUSTRIAL - RPM III ENCLOSURE: TOTALLY ENCLOSED COOLING; FAN COOLED MOUNTING; ROUND BODY, RIGID MOUNTING OPTIONAL FRAMES SE56C-LE56C NEMA C FACE Analolg DC Drives Dimensions are in inches BF Tap Frame D (1) AC O E R P BB BD AK (4) BF Tap Depth AJ BA SE56C-LE56C 3.50 3.28 7.81 2.44 6.38 7.31.12 5.66 4.500 3/8-16.56 5.88 2.75 Drive End Shaft And Key Frame C BV BS 2F H B N-W U (2) AH R (3) Sq Lgth SE56C 12.06 6.06 3.50 3.00.34 4.10 1.88.6250 2.06 517.19 1.25 ME56C 13.06 7.06 4.50 3.00.34 4.10 1.88.6250 2.06.517.19 1.25 LE56C 15.06 9.06 6.50 3.00.34 4.10 1.88.6250 2.06.517.19 1.25 (1) D dimension varies +.00, -.03. (2) U varies +0000, -.0005. (3) R varies +.00, -.02. (4) AK varies +.000, -.003. Face runout and eccentricity.004 max. T.I.R. If mounting clearance details are required consult factory. D4-6
MICRO 100 PRICING DC PWM Drives with Speed Pot Reference HP (1) Input Voltage (VAC) Output Voltage (VDC) Model List (1) 1/4-1/2 115 120 1DN11050 $110 3/4 115 120 1DN11075 110 3/4-1 230 240 1DN21001 115 Option: 5K ohm speed pot (standard on speed pot reference models) for use with Isolated Reference models where manual speed pot and 0-10 VDC follower models is required. Model 1DN1000.................................. $45 List DC PWM Drives with 0-10 VDC Isolated Reference Follower Input Heat Sink Kit 1DN2000........................... $50 List Data Sheet: D-2894 Instruction Manual:(Drive) D-3393 (1) For.50 HP and above, a heat sink kit is necessary to meet rated HP at rated ambient or the drive must be mounted with thermal grease to an aluminum plate 18 x 18 x 0.125. NEMA 34 and NEMA 42 Frame PWM Rated Permanent Magnet DC Motors NEMA 56 Frame PWM Rated Permanent Magnet DC Motors HP (1) Input Voltage (VAC) Output Voltage (VDC) Model List (1) 1/4-1/2 115 120 1DN12050 $115 3/4 115 120 1DN12075 115 3/4-1 230 240 1DN22001 115 HP Base RPM Enclosure Voltage (DC) Model Number Options List 1/4 1/3 1/2 3/4 NEMA 34 Frame 1750 TENV 120 0660-04-076 Motor Only $180 1750 TENV 120 0660-04-077 Conduit Box (CB) 220 1750 TENV 120 0660-04-078 Brake 250 1750 TENV 120 0660-04-079 CB and Brake 295 1750 TENV 120 0675-03-018 Motor Only 190 1750 TENV 120 0675-03-019 Conduit Box (CB) 230 1750 TENV 120 0675-03-020 Brake 260 1750 TENV 120 0675-03-021 CB and Brake 310 1750 TENV 120 0690-02-008 Motor Only 210 1750 TENV 120 0690-02-009 Conduit Box (CB) 240 1750 TENV 120 0690-02-010 Brake 270 1750 TENV 120 0690-02-011 CB and Brake 320 NEMA 42 Frame 1750 TENV 120 0723-03-047 Motor Only 320 1750 TENV 120 0723-03-048 Conduit Box (CB) 370 1750 TENV 120 0723-03-049 Brake 400 1750 TENV 120 0723-03-050 CB and Brake 445 1750 TENV 120 0723-03-052 56 C-Face 360 HP Base RPM Enclosure 1/4 1/3 1/2 3/4 1 Normally carried in stock Voltage (DC) Frame Foot Mount C-Face Model Number List Dimension Sheet 1750 TEFC 120 SE56C T56S6534 $335 616050-1 1750 TEFC 120 SE56C T56S6540 340 616050-1 1750 TEFC 120 SE56C T56S6535 340 616050-1 1750 TEFC 120 SE56C T56S6541 340 616050-1 1750 TEFC 120 ME56C T56S6536 345 616050-1 1750 TEFC 120 ME56C T56S6542 350 616050-1 1750 TEFC 120 LE56C T56S6537 350 616050-1 1750 TEFC 120 LE56C T56S6543 355 616050-1 1750 TEFC 240 LE56C T56S6539 390 616050-1 1750 TEFC 240 LE56C T56S6545 395 616050-1 1750 TEFC 240 LE56C T56S6538 395 616050-1 1750 TEFC 240 LE56C T56S6544 400 616050-1 DISCOUNT VS-3DC Controls, VS-4DC Motors Analog DC Drives D4-7
NOTES Analolg DC Drives D4-8