Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 00000000 W Constant Voltage Constant Current LED Driver IP65 IP67 Metal housing with class I design Ⅰ current output. HLGH operates from 90~305VAC and offers models with different rated voltage ranging between V and 54V. Thanks to the high efficiency up to 93%, with the fanless design, the entire series is able to operate for 40 ~ 90 case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLGH is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. I I B D File Name:HLGHSPEC 161025
SPECIFICATION MODEL HLGH HLGH24 HLGH30 HLGH36 HLGH42 HLGH48 HLGH54 DC VOLTAGE CONSTANT CURRENT REGION Note.4 V 10 ~ V 24V 12 ~ 24V 30V 15 ~ 30V 36V 18 ~ 36V 42V 21 ~ 42V 48V 24 ~ 48V 54V 27 ~ 54V RATED CURRENT RATED POWER 4.8A 96W 4A 96W 3.2A 96W 2.65A 95.4W 2.28A 95.76W 2A 96W 1.77A 95.58W RIPPLE & NOISE (max.) Note.2 150mVpp 150mVpp 0mVpp 0mVpp 0mVpp 0mVpp 0mVpp OUTPUT VOLTAGE ADJ. RANGE Adjustable for AType only (via builtin potentiometer) 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 38 ~ 46V 43 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE Adjustable for AType only (via builtin potentiometer) 3 ~ 4.8A 2.5 ~ 4A 2 ~ 3.2A 1.65 ~ 2.65A 1.4 ~ 2.28A 1.25 ~ 2A 1.1 ~ 1.77A VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME Note.6 10ms,50ms/115VAC 500ms,50ms/230VAC HOLD UP TIME (Typ.) 16ms / 115VAC, 230VAC VOLTAGE RANGE Note.5 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF 0.98/115VAC, PF 0.95/230VAC, PF 0.93/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< % (@ load 60% / 115VAC,230VAC; @ load 75% / 277VAC) TOTAL HARMONIC DISTORTION INPUT (Please refer to " TOTAL HARMONIC DISTORTION (THD)" section) EFFICIENCY (Typ.) AC CURRENT (Typ.) 93% 1.2A / 115VAC 93% 0.55A / 230VAC 93% 0.5A / 277VAC 93% 93% 93% 93% INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 60A(t width=415 μs measured at 50% I peak ) at 230VAC; Per NEMA 410 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC OVER CURRENT 95 ~ 106% Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION 23 ~ 27V 28 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V OVER VOLTAGE Shut down o/p voltage with autorecovery or repower on to recovery 54 ~ 63V 59 ~ 65V OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase= 40 ~ 90 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase= 90 ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 60 ) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY & EMC OTHERS NOTE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION Note.8 UL8750 (type HL ), CSA C22.2 No. 250.008; TUV EN613471, EN61347213 independent; IP65 or IP67, J613471, J61347213 approved ; design refer to UL609501, TUV EN609501 I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Note.8 Compliance to EN55015, EN55022 (CISPR22) Class B, EN6032 Class C (@ load 60% ) ; EN6033 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547, EN55024, light industry level ( surge immunity LineEarth 4KV, LineLine 2KV) MTBF 192.2K hrs min. MILHDBK217F (25 ) DIMENSION 2*68*38.8mm (L*W*H) PACKING 1.12Kg; 12pcs/14.4Kg/0.8CUFT File Name:HLGHSPEC 161025
BLOCK DIAGRAM Fosc : KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. V V DIM DIM (B Type) DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 Io (%) Typical output current normalized by rated current (%) File Name:HLGHSPEC 161025
DIMMING OPERATION HLGH DIM(Blue) DIM(White) V(Black) V(Red) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) % 90% 80% 70% 60% 50% 40% 30% % 10% 10% % 30% 40% 50% 60% 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) % 90% 80% 70% 60% 50% 40% 30% DO NOT connect "DIM to V" % 10% 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLGHSPEC 161025
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Swih Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLGH BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a swih and relay can turn ON/OFF the lighting fixture. File Name:HLGHSPEC 161025
OUTPUT LOAD vs TEMPERATURE 80 80 60 60 LOAD (%) 40 LOAD (%) 40 40 25 10 0 15 30 50 60 70 (HORIZONTAL) 40 25 0 45 55 65 75 90 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 80 Constant Current Mode LOAD (%) 90 80 70 60 50 40 PF 1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 277Vac 230Vac 115Vac 90 125 135 145 155 165 175 180 0 230 305 50% 60% 70% 80% 90% % INPUT VOLTAGE (V) 60Hz LOAD (W) Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 80 25 EFFICIENCY vs LOAD possess superior working efficiency that up to 93% can be reached in field applications. 48V Model, Tcase at 80 94 90 86 THD(%) 15 10 5 115VAC 230VAC 277VAC EFFICIENCY (%) 82 78 74 70 66 62 277Vac 230Vac 115Vac 0 50% 60% 70% 80% 90% % 58 10% % 30% 40% 50% 60% 70% 80% 90% % LOAD LOAD File Name:HLGHSPEC 161025
LIFETIME 1 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tc a s e ( ) File Name:HLGHSPEC 161025
MECHANICAL SPECIFICATION Blank/DType Case No.994A Unit:mm 12 9.6 2 196 AType 3C 3C 12 9.6 9.4 9.4 34.2 9.4 9.4 34.2 68 Tcase : Max. Case Temperature 68 34 2 196 Tcase 34 98 Vo ADJ. 98 Io ADJ. SJTW 14AWG ψ 4.2 4PL SJTW 14AWG ψ 4.2 4PL V(Black) V(Red) 38.8 V(Black) V(Red) : Max. Case Temperature 38.8 BType 2 12 196 3C 9.6 9.4 34.2 9.4 Tcase : Max. Case Temperature 38.8 68 34 98 ψ 4.2 4PL SJTW 14AWG DIM(Blue) DIM(White) V(Black) V(Red) File Name:HLGHSPEC 161025
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLGH to operate in dry/wet/damp or outdoor environment. AC source I/P HLGH O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLGH O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. Junction Box Option 196 358 76 10 5 3C 68 61 8.5 32 8.5 6 V(Black) V(Red) SJTW 14AWG 2ψ5 3 PF 1/2" 150± 35 38.8 3 PF 1/2" 150± Junction box option is available for A / Blank Type. Please contact MEAW WELL for details. 86 INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html File Name:HLGHSPEC 161025