Model Name : Features : ㅡ Suitable for LED lighting application ㅡ UL8750, UL1310 Class 2 ㅡ For use in Dry and Damp Location ㅡ Full-protection provided: OCP/OVP/OTP/SCP ㅡ 0-10V Dimming Control ㅡ IP67 ㅡ 5-years warranty
Electrical specification No. Item Min Typ Max Unit Remark 1 Nominal Input Voltage 100 277 Vac 2 Wide Input Voltage 90 305 Vac 3 Maximum Input Current 1.5 Arms 4 Nominal Input Frequency 50 60 Hz 5 Wide Input Frequency 47 63 Hz 6 Power Factor (PF) 0.9 1) 7 Total Harmonic Distortion (THD) 20 % 1) 8 Inrush Current NEMA410 10) 9 Earth Leakage Current 500 μa 10 Insulation Resistance 100 MΩ 500Vdc between Input & Output 11 Output Voltage 28 32 36 Vdc 12 Output Current 1,330 1,400 1,470 ma @30min Aging, 1) 13 Output Current Ripple 210 ma 1) 14 Output Peak Current 2,800 ma 1) 15 Output Aging Current Differential ±70 ma @2hr Aging 16 Turn-on Delay 1,500 ms 2) 17 Electrical Efficiency 85 % 3) 18 12V Output Voltage 10.8 12 13.2 Vdc 12V Max and No Load, 1) 19 12V Output Current 50 100 ma 20 Dimming Control 0 10 Vdc 4) 21 Output Over Voltage Protection - - 42.4 Vdc Auto-recovery 22 Output Short Circuit Protection - - - - Auto-recovery or Latch-off 23 12V Output Short Circuit Protection - - - - Auto-recovery or Latch-off 24 Over-temperature Protection 105 Auto-recovery or Latch-off 25 Case Temperature (Tc) 85 26 Storage Temperature -30 85 27 Operating Temperature -30 50 28 Differential Mode (Line to Line) -4 4 kv 5) 29 Common Mode (Line to Ground) -6 6 kv 5) 6) 30 Contact Discharge Test Voltage -4 4 kv 7) 31 Air Discharge Test Voltage -8 8 kv 7) 8) 32 Vibration 3 G 33 Humidity 90 % 34 Dielectric Input to Output 1,554 Vac Apply for 1 minute 35 Withstand Input to Case 1,554 Vac 9) 36 Voltage Output to Case 500 Vdc
Application Notes 1) Test Condition: 100/277Vac 50/60Hz Input, Typical LED Load, Ambient Temp. 25 2) Test Condition : Input 240Vac 60Hz, Typ. Load, Cold start 3) Test Condition: 240Vac Input, 30min Aging, LED Typ. Load, 12V Output no Load 5) Surge Specification above is higher than EN 61000-4-5 (Differential 1kV, Common 2kV ) 6) The metal case of the LED driver must be connected with F.G 7) ESD Specification above meets EN 61000-4-2 Requirements (Contact 4KV, Air 8KV) 8) The metal case of the driver should be grounded. 9) Determined by Paragraph 34.1.2, UL1310 or Paragraph 8.4.2, UL8750, EN61347-1, EN61347-2-13 10) Input 120Vac, < 192Apeak, < 1.2ms, < 74A2sec Dimming Curve 100% Dimming ratio 10% 1V Dimmer Voltage 10V Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 UL8750, UL1310, UL1012 UL Safety Standards (Class 2, Dry and Damp Location) 2 FCC Part 15, Class B Conducted and Radiated Emission Test 3 IEC 61000-3-2 Harmonic current emissions: Class C 4 IEC 61000-3-3 Voltage Fluctuations and Flicker 5 IEC 61000-4-2 Electrostatic Discharge (ESD): Contact 4KV, Air 8KV 6 IEC 61000-4-3 Radio-frequency Electromagnetic Fields 7 IEC 61000-4-4 Electrical Fast Transients (EFT Level 2) 8 IEC 61000-4-5 Surges: Differential 1kV, Common 2kV 9 IEC 61000-4-6 Injected Currents 10 IEC 61000-4-8 Power Frequency Magnetic Fields 11 IEC 61000-4-11 Voltage Dips and Short Interruptions
Life Time vs Tcase 120000 100000 Life Time [Hrs] 80000 60000 40000 20000 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 hours @ Tc 70 Efficiency(%) Efficiency (%) 88.00 87.00 86.00 85.00 84.00 83.00 82.00 81.00 80.00 90 100 240 277 300 Input Voltage(Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V)
Power Factor 0.9900 0.9700 0.9500 PF 0.9300 0.9100 0.8900 0.8700 0.8500 90 100 240 277 300 Input Voltage (Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V) THD(%) THD [%] 20.00 18.00 16.00 14.00 12.00 10.00 8.00 6.00 4.00 2.00 0.00 90 100 240 277 300 Input Voltage (Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V)
Mechanical Specification Enclosure Size Unit Width Length Height mm 70 180 33 inch 2.76 7.09 1.30 Mounting Length Overall Length 188 196 7.40 7.72 Case Material : Aluminium
Wiring Diagram INPUT OUTPUT LIVE LED DRIVER LED + LED - +12V C O N NEUTRAL DIM+ C O N DIM-/GND Remark) Output wiring specifications can be changed. Rating Label Drawing