Specification Features Physical Characteristics Module Source Type: Corrected Cold Phosphor LED Module. Dia. 50mm (1.97 ) x 20mm (0.79 ). Light emitting surface Ø 19mm (0.75 ). Maximum Case Temperature: 90 C Phosphor Proximity: Photometric Characteristics Color Consistency Initial: 1 x 2 MacAdam (1 x 2 SDCM) along BBL. Color Rendering Index (CRI): Ra: 83 (typical). Values ±3. Color Consistency Maintained: C3/B10/F10 50,000 hrs. (<0.003 u,v 5 years/44,000 hrs. warranty 10 ). Lumen Maintenance: L80/B10/F10 50,000 hrs. (L70, B0, F0 5 years/44,000 hrs. warranty 10 ). Other Remote Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 ). Interfaces- Electrical Interface- Mechanical Interface- Thermal Module Housing: Storage Temperature: -40 C to 85 Electrical: 6-Pin terminal. Tyco part # 353908-6P. Mating connector Tyco 353907-1. Pin-out: P1 + power, P2 - power, P3 open, P4 open, P5 control+, P6 control-. 600mm harness accessory available through Avnet (part #2829114-2). Xicato sample part # XSA-331. Mechanical: Recommended mounting screws: M3 x 0.5mm x 25mm with split lock washer. Torque 0.4Nm (3.5 in-lb) using three-hole pattern. Thermal: Integral thermal pad. A mating thermal interface (i.e. heatsink) surface flatness of 0.1 mm and center hole less than Ø12 mm is recommended in order to maintain thermal performance. Injection molded glass-filled PBT. Regulatory: Mercury Content UV or IRC Emissions: UL recognized Class 2, CE (IEC62031, Class III), RoHS 2 compliant. IP20. Photobiological Safety (EN62471:2008), ESD Class 3B (HBM). 1-10V standard compliant (IEC60929 Annex E). None None Module Lifetime 100,000 hrs.mtbf @ 90 C 10 PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 1
Color Information Color Consistency Initial Color Consistency Maintained Spectral Power Distribution Color Gamut Color Rendering Index (3000K Typical) Ra R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 Standard Series 83 82 89 95 84 82 87 86 65 16 64 79 58 81 93 75 PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 2
Intensity Intensity PRODUCT DATA SHEET Dimming Information Dimming Protocol: 1-10V/0-10V (IEC60929 Annex E) Dimming Profile: Linear Dimming Compatibility: XIM is compatible with a wide range of 1-10V sink dimming systems from leading industry manufacturers. Potentiameter 100k Ohm Compatibility The following graphs show how the 1-10V control voltage is converted to the commanded intensity. The graph on the left shows the entire intensity range. The graph on the right shows the 0 2% intensity range and shows the hysteresis of the intensity response to the 1-10V voltage. When the light is off (intensity is ), then the 1-10V voltage must be set to at least 0.75V in order to turn on the light. When the light is on, then the 1-10V voltage must be set to less than 0.5V to turn off the light. When the light is on and the 1-10V voltage is between 0.5 and 1.0V, the intensity will be 1.. When the 1-10V voltage is greater than 9.0V, the intensity will be 10. When the 1-10V voltage (V1-10V) is between 1V and 9V, the intensity will be: Intensity = 12.375% * (V1-10V 1V) + 1% Intensity vs. Voltage Mapping: 0-10 Intensity Range (Left) and 0-2% Intensity Range (Right) 10 9 8 7 6 5 4 3 0 1 2 3 4 5 6 7 8 9 10 11 1-10V Voltage (V) 2. 1.5% 1. 0.5% 0. 0 0.25 0.5 0.75 1 1.25 1-10V Voltage (V) PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 3
Intensity (Log Scale) Intensity (Linear Scale) Intensity (Log Scale) Intensity (Linear Scale) Intensity (Log Scale) Intensity (Linear Scale) Intensity (Log Scale) Intensity (Linear Scale) PRODUCT DATA SHEET The following graphs show the dimming response to an instantaneous change in the 1-10V control voltage. The XIM smoothly fades its intensity until it reaches the commanded intensity. The blue line represents the intensity with respect to the logarithmic scaled y-axis (left axis of each graph). The red line represents the intensity with respect to the linear scaled y-axis (right axis of each graph). Fade from to 10 (Left) and Fade from 10 to (Right) Intensity Curves 100.0 10 100.0 10 9 9 10.0 8 10.0 8 7 7 1.0 6 1.0 6 5 5 0. (Linear Scale) 4 3 0. (Linear Scale) 4 3 0.01% (Log Scale) 0.01% (Log Scale) 0.0 0 100 200 300 400 500 600 700 800 900 1000 0.0 0 100 200 300 400 500 600 700 800 900 1000 Time (ms) Time (ms) Fade from 1% to 10 (Left) and Fade from 10 to 1% (Right) Intensity Curves 100.0 10 100.0 10 9 9 10.0 8 10.0 8 7 7 1.0 6 1.0 6 5 5 0. (Linear Scale) 4 3 0. (Linear Scale) 4 3 0.01% (Log Scale) 0.01% (Log Scale) 0.0 0 100 200 300 400 500 600 700 800 900 1000 0.0 0 100 200 300 400 500 600 700 800 900 1000 Time (ms) Time (ms) PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 4
Over Temperature Protection LED luminaires are designed to operate within a specific ambient temperature range. Occasionally the ambient temperature will exceed the design temperature. For example, if insulation is unintentionally placed on or near the luminaire. Additionally, the thermal management system (e.g. heat sink) may get installed incorrectly, which could increase the LED module s temperature above the recommended limit. In these cases, the performance of the electrical components (LEDs and driver electronics) are placed at risk. To address this risk, XIM features over-temperature protection. XIM contains a temperature sensor, that monitors the Tc of the LEDs. If the temperature exceeds 93 C, XIM s integrated electronics reduce the intensity which then lowers both current and the temperature. The intensity is reduced to 85% of the commanded intensity over a period of 60 seconds. If the temperature drops below 93 C, but stays above 85 C, XIM will maintain the intensity at the reduced level. If the temperature drops below 85 C, XIM will increase intensity back to 10 of the commanded intensity over a period of 60 seconds. The Thermal Overload diagram below illustrates this behavior. PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 5
If the module temperature stays below 98 C, but stays above 93 C for 5 minutes, XIM will immediately limit the maximum intensity to. The intensity limit will stay at even if the temperature drops below 85 C. To remove the limit, the user must set the commanded intensity to (turn off the light) and the temperature must be below 93 C. Then, when the user sets the commanded intensity to above (turns on the light), XIM will set the light to the commanded intensity (no reduction). A power cycle of XIM will also remove the limit. The Thermal Overload Lockout diagram below illustrates this behavior. If at any time, the module temperature exceeds 98 C, XIM will immediately turn off the LEDs. The LEDs will stay off even if the temperature drops below 85 C. To turn on the LEDs again, the user must set the commanded intensity to (turn off the light) and the temperature must be below 93 C. Then, when the user sets the commanded intensity to above (turns on the light), XIM will set the light to the commanded intensity (no reduction). A power cycle of XIM will also allow the LEDs to be turned on. The Thermal Shut Down diagram below illustrates this behavior. PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 6
Technical Data Lighting 1 Electrical 5 Module Part Number Correlated Color Color Rendering Temperature (CCT) 2 Index (Ra) 3 Initial Color Consistency SDCM CCT Duv Lumen Maintenance (hrs) 4 Control Protocol Constant Voltage (V) 6 Required Input Parameters Module Power Consumption (W) Lumen Output (Typical) 8 Efficacy (Typical) Minimum Current (ma) 7 Typ. Max lm lm/w XIM19802713A3A 2700K ± 40K 1300 lm 2000 lm XIM19803013A3A XIM19803513A3A XIM19804013A3A XIM19802720A3A XIM19803020A3A XIM19803520A3A XIM19804020A3A 3000K 3500K 4000K 2700K 3000K 3500K 4000K ± 50K ± 60K 83 ±3 1 x 2 ± 70K ± 40K ± 50K ± 60K ± 70K ± 0.001 1. All lighting data shown in the above table is taken at a recommended operating test point (Tc) temperature of 70 C and highest rated drive current. 2. "3000K" and "3500K" CCT's are 2950K and 3420K, respectively. CCT data ANSI/NEMA compliant. 3. Ra is defined as the average of color rendering indices R1-R8. 3000K data shown. Value is typical. 4. L80 50,000 hrs. Long term testing in process. 5. The module is designed for usage with a constant voltage power supply. 6. Absolute minimum voltage into the module is 41V. Absolute maximum voltage into the module is 56V. These specifications include PSU output tolerance, ripple, noise, wire length voltage drop, line regulation, load regulation, over/undershoot, turn on delay, or any other source of variation. Voltage data based on 20 C to 90 C operating range. For operation outside this range, contact Xicato. 7. While the PSU is energized, the PSU must be able to supply up to 5mA, even when the light is commanded off via a lighting control system. Minimum input current to the XIM is the minimum current that the PSU must be able to supply in all conditions to ensure full light output. 8. Absolute range of lumen output is ± of typical value. 9. Specifications subject to change without notice. 10. 5 year color and lumen maintenance warranty. Refer to www.xicato.com for details. 50k 1-10V 48 ± 5% 360 13.1 14.8 1300 99 48 ± 5% 580 21.2 23.8 2000 94 PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 7
Recommended LED Module in Luminaire Specification Physical Characteristics: LED module shall be Corrected Cold remote phosphor, nominal 50mm (1.97 ) diameter, and 20mm (0.79 ) in height. Performance: LED module shall have a CRI (Ra) 83. CRI values shall be ±3 points initial. LED module color points shall be within 1 x 2 SDCM initial. Flux output and color point shall be tuned at a minimum of 70 ºC (±5ºC). Dimming Performance: Module shall be 1-10V/0-10V, compatible with IEC60929 Annex E. Module shall dim to 1. (measured flux) at lowest level. Fading across the dimming range shall be smooth and monotonic. Dim to off/on shall be within 500ms. Minimum flicker frequency at 1% measured light output shall be 1.25 khz. General Requirements: LED module shall be UL recognized, CE compliant and RoHS compliant. Module shall be warranted for 5 years for catastrophic failure, lumen maintenance ( L70), and color consistency (<.003 u, v ). LED module shall be Xicato Module. # About Xicato Xicato is passionate about light. Light has an emotional effect on people and a direct impact on business profitability. It ultimately influences everything in our lives. Xicato is a recognized leader in creating LED modules that provide superior aesthetics, economics and durability. Xicato aspires to be the trusted partner of the global lighting design community and luminaire manufacturers. For an overview of our customers luminaires visit www.xicato.com. PRODUCT DATA SHEET: XIM LED Module 1-10V, Standard Series Oct. 23 14. pg. 8