NOPY SYSTEMS PGE 1 OF 1 SY 092 I N S T L L T I O N I N S T R U T I O N S RED REFULLY! minimum of of two persons are required to install canopies. Do not step on base shelves... to avoid damage:. Do not install base shelves initially, or. Remove individual base shelves while working and replace, or. Lay plywood or boards on base shelves. TOOLS REQUIRED 7/16" wrench, box or open end # Phillips, apex or screwdriver Framing square #2 Phillips, apex or screwdriver Fine tooth finishing saw Step ladder. PRTS IDENTIFITION NOTE! These canopy / canopy flange combinations are designed to install on: ll standard upper shelves...sus-. Open canopy brackets...o-, see below. djustable canopy brackets...f-, see below. IMPORTNT! ll L-88 and D-88 canopy installations begin with a canopy end panel, or canopy end. See page 2 for how these components interface with canopy ends and canopy end panels. L-88 F-88 "LITE-EX" with NOPY NOPY FLNGE...see pages thru. D-88 FHP97 "DELUXE" with NOPY NOPY FLNGE...see pages 5 thru 7. MS- 6502-618 METL with NOPY NOPY FLNGE...see pages 8 thru 10. O- OPEN NOPY RKET F- DJUSTLE NOPY RKET...see page 12, 1. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 2 OF 1 SY 092 7" NOPY FLNGE EXTENSION...either F-88, FHP97 or 6502-618 flange. NOPY SHELF DEPTH + 9" = NOPY END DEPTH N O P Y P R O J E T I O N S 2" NOPY FLNGE EXTENSION...either F-88 or FHP97 flanges. NOPY SHELF DEPTH + 5" = NOPY END DEPTH LIGHT FIXTURE MOUNTS ON LL NOPY FLNGES or LIGHT FIXTURE MOUNTS ON K OF L-88 OR D-88 NOPIES ONLY. " RDIUS NOPY END LEFT HND LIGHT FIXTURE MOUNTS ON... EXTENSION NOPY NOPY K OF LENGTH TYPE FLNGE NOPY 7 L-88 YES YES EXTENSION D-88 YES YES MS YES NO 2 L-88 NO YES EXTENSION D-88 NO YES MS NO NO LIGHT FIXTURE MOUNTS ON K OF L-88 OR D-88 NOPIES ONLY. SQURE NOPY END RIGHT HND ONE PIEE RDIUS NOPY END PNEL RIGHT HND NOPY NOPY SHELF OR RKET END DEPTH FOR X EXTENSION: DEPTH 7 EXT. 2 EXT. 17" 8" 12" 19" 10" 1" 21" 12" 16" 2" 1" 18" 25" 16" 20" 27" 18" 22" 29" 20" 2" 1" 22" 26" " 2" 28" 5" 26" 0" 7" 28" N.. 9" 0" N. ONE PIEE SQURE NOPY END PNEL LEFT HND LEFT HND OR RIGHT HND PPLIES ONLY IF THE EXTERIOR ND INTERIOR FINISHES RE DIFFERENT. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE OF 1 SY 092 F-88 HRDWRE PK #7200-028 QTY ITEM DESRIPTION 6 1/-20 x 1/2 Phillips truss head machine screw 6 1/-20 Hex nut D 6 1/ x 1 O.D. Fender washer 2 #10 x 5/8 Phillips pan head sheet metal screw 1 IMPORTNT! Leave all canopy flange screws slightly loose until the canopy and canopy ends/end panels are installed. INSTLLING F-88 NOPY FLNGES... FOR L-88 NOPY NOTE! Hardware pack is for one flange. Two of each items marked are included for fastening the light fixture to the flange or canopy. 7" EXTENSION ON UPPER SHELF...for 2" extension, slide the flange back and use the front set of ovals. INSTLL IN THIRD SLOT FROM TOP T ENDS LL ENTERS 7" EXTENSION ON NOPY RKET...for 2" extension, slide the flange back and use the front set of ovals. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE OF 1 SY 092 2 5 6 7 8 fter the canopy flanges have been installed, with screws slightly loose, see pages 12-1 to install a canopy end panel, or canopy end, prior to beginning the canopy installation. Slide insert panels slightly over 1 out of trim extrusion as shown. Repeat with all 8' remaining sections used in run. ut 1' off of the starting section... using a framing square and a fine tooth saw to avoid chipping. Hang first section on canopy flanges by inserting expansion flange into upper extrusion pocket. Hang second section on canopy flanges, inserting the second section panel into the first section extrusions,...close the extrusion gaps. Repeat steps -5 through to the last section. Insert the 1' piece cut from the first section...cut extrusion and/or panel to length as necessary. e sure to match the joint as shown. 2 L - 8 8 N O P Y 7' 5 6 7 8 I N S T L L T I O N t all canopy flanges, insert the down flange into the lower extrusion 9 See page 12-1 to 10 Visually sight the canopy for in/out alignment pocket, while tightening the install the remaining while tightening the canopy flange screws...if the expansion screw so that canopy end panel, or canopy cannot be aligned, refer to SY-06 for releveling the canopy is secure. canopy end. fixture. 1' P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 5 OF 1 SY 092 INSTLLING FHP-97 NOPY FLNGES... FOR D-88 NOPY F-88 HRDWRE PK #7200-028 QTY ITEM DESRIPTION 6 1/-20 x 1/2 Phillips truss head machine screw 6 1/-20 Hex nut 6 1/ x 1 O.D. Fender washer D 2 #10 x 5/8 Phillips pan head sheet metal screw NOTE! Hardware pack is for one flange. Two of each items marked are included for fastening the light fixture to the flange or canopy. 1 IMPORTNT! Leave all canopy flange screws slightly loose until the canopy and canopy ends/end panels are installed. 7" EXTENSION ON UPPER SHELF...for 2" extension, slide the flange back and use the front set of ovals. INSTLL IN THIRD SLOT FROM TOP T ENDS LL ENTERS 7" EXTENSION ON NOPY RKET...for 2" extension, slide the flange back and use the front set of ovals. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 6 OF 1 SY 092 D - 8 8 N O P Y I N S T L L T I O N EXMPLE SHOWN IS FOR 2' RUN 2 fter the canopy flanges have been installed, with screws slightly loose, see pages 1-1 to install a canopy end panel, or canopy end, at each end of the run prior to beginning the canopy installation. Position first canopy section butting against the canopy end and the " return against the bottom of the canopy flange. Screw the canopy to the canopy flange as shown. See page 1 for securing the canopy to the canopy end, be sure the " return is against the bottom of the canopy flange, then screw the canopy to the canopy flange as shown in step. D-88 HRDWRE PK #7200-8 QTY ITEM DESRIPTION E 1 TITE-JOINT fastener F 1900-159-1.500, 8 gauge x 1 1/2" steel pins G #10 x 5/8" Phillips pan head sheet metal screw G E P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 7 OF 1 SY 092 5 6 D-88 NOPY INSTLLTION, ONT D 5 6 7 8 9 Join the first and second canopy sections, inserting the steel pins and tapping the joint snug. e sure the " return is against the bottom of the canopy flanges as you screw the canopy to the canopy flange as in step. Insert the "Tite-joint " fastener downward at the canopy joint between the canopy and the canopy flange as shown. djust the fastener so that both plates are in the routed pockets of the canopy sections. Tighten the fastener using the open end wrench on the bolt head. Screw the canopy to the canopy flange as shown in step. Join the second and third canopy sections by repeating step 5. Secure the canopy joint by repeating step 6. Secure the third canopy section to the canopy end by repeating step. E 6 G 8 7 9 P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 8 OF 1 SY 092 INSTLLING 6502-618 NOPY FLNGES... FOR MS METL NOPY MS HRDWRE PK #7200-028 QTY ITEM DESRIPTION 6 1/-20 x 1/2 Phillips truss head machine screw 6 1/-20 Hex nut 6 1/ x 1 O.D. Fender washer NOTE! Hardware pack is for one flange. Two of each items marked are included for fastening the light fixture to the flange or canopy. 1 IMPORTNT! Leave all canopy flange screws slightly loose until the canopy and canopy ends/end panels are installed. 7" EXTENSION ON UPPER SHELF...for 2" extension, slide the flange back and use the front set of ovals. INSTLL IN THIRD SLOT FROM TOP T ENDS LL ENTERS 7" EXTENSION ON NOPY RKET...for 2" extension, slide the flange back and use the front set of ovals. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 9 OF 1 SY 092 MS METL NOPY INSTLLTION MS- METL NOPY 2 5 MSE- DJUSTLE END OVER, pair Lay out the canopy sections to check that you have the correct lengths to correspond to the section widths. Position the beginning canopy section so that it is resting on top of the canopy flanges as shown and is flush with the side of the end canopy flange. Secure with the screw into the weld nut beneath, as shown, leaving the screw slightly loose...see step 5. Screw the opposite end of the beginning canopy section to the canopy flange. anopy sections 6' or longer have perforations for intermediate canopy flanges...screw these as well. Leave all screws slightly loose...see step 5. Flanges at canopy section joints and intermediate flanges will secure the same way. Repeat step with the remaining canopy sections. Leave all screws slightly loose...see step 5. 6502-618 METL NOPY FLNGE WELD NUTS UNDER THESE TWO HOLES MS HRDWRE PK #7200-5 QTY ITEM DESRIPTION 12 1/ - 20 x 1/2" Phillips truss head machine screw 8 1/-20 Hex nut NOTE! Hardware pack is for one flange. Two extra of each item are included for fastening the light fixture to the flange. P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 10 OF 1 SY 092 MS METL NOPY INSTLLTION, ONT D 6 7 8 9 10 Leaving the canopy to flange screws loose in previous steps is to allow tilting the bottom of the canopy forward to allow access for installing the canopy joint screws. eginning at one end, install screws as shown. e sure that the front and bottom surfaces are aligned prior to tightening the screws eginning at the first joint, tighten all of the canopy to flange screws. If using the matching MSES metal canopy end, install it into the top slot of the upright. The top of the canopy end must be flush with the top of the upright as shown. Secure the canopy section to the canopy end as shown. If using wood canopy ends, or canopy end panels, see pages 12-1. Visually sight the canopy for in/out alignment while tightening the canopy flange screws...if the canopy cannot be up/down aligned, refer to SY-06 for re-leveling the fixture. MSE HRDWRE PK #7200-5 QTY ITEM DESRIPTION 1/ - 20 x 1/2" Phillips truss head machine screw D 1/-20 Hex nut D P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 11 OF 1 SY 092 DJUSTLE NOPY RKET... FIXTURE MOUNT HOUSING 1 Insert all brackets into the uprights at the fourth slot from the top, as shown above. 2 5 6 7 Secure housing to bracket as shown...be sure that the bracket to housing position is as shown in the front view, below. NOTE! The housing is reversible end for end...examine the front view drawing below carefully in order to determine the bracket to housing down flange position. Push the housing firmly back against the upright while tightening the screws to eliminate side to side sway. Insert the extension into the housing and secure the canopy flange to the extension as shown in the top view, below. djust the extension to the desired depth and install and tighten the lock screw on the bottom side of the housing. Repeat all steps above with all the remaining uprights in the run. Refer to page 1 of this instruction for the specific canopy type to be installed and follow those steps to complete the installation. D RKET MOUNTS IN FOURTH SLOT DOWN FROM TOP EXTENSION F-88 NOPY FLNGE SHOWN...FHP97 FLNGE, page 5, or FM NOPY FLNGE, page 8, MY LSO E USED. FRONT VIEW TOP VIEW NOTE! Hardware pack is for one flange. Two extra of each item marked are included for fastening the light fixture to the flange. LEFT END F HRDWRE PK #7200-25 QTY ITEM DESRIPTION 2 1/ - 20 x 1 1/" PhilLips truss head machine screw 6 1/-20 Hex nut 1/" Lock washer D 5 1/-20 x 1/2" Phillips truss head machine screw F DJUSTMENT 18-2 2-6 RKET LENGTH 8 7/8 1 7/8 HOUSING LENGTH 9 15 EXTENSION LENGTH 12 18 LL ENTERS RIGHT END P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 12 OF 1 SY 092 DJUSTLE NOPY RKET... WLL MOUNT HOUSING 1 2 Secure housing to extension as shown...insert the extension into the housing and secure the canopy flange to the extension as shown. When mounting housing to wall, take into account that the canopy flanges cannot be mounted directly on the housing/extension centerline...see top view, page 11. NOTE! Due to to varying field conditions, housing to wall anchors are not provided. djust the extension to the desired depth and install and tighten the lock screw on the bottom side of the housing. Refer to page 1 of this instruction for the specific canopy type to be installed and follow those steps to complete the installation. D EXTENSION F-88 NOPY FLNGE SHOWN...FHP97 FLNGE, page 5, or 6502-618 METL NOPY FLNGE, page 8, MY LSO E USED. W HRDWRE PK #7200-26 QTY ITEM DESRIPTION 2 1/ - 20 x 1 1/" Phillips truss head machine screw 1/-20 Hex nut 2 1/" Lock washer D 1/-20 x 1/2" Phillips truss head machine screw NOTE! Hardware pack is for one flange. Two extra of each item marked are included for fastening the light fixture to the flange. W DJUSTMENT 18-2 2-6 HOUSING LENGTH 11 1/ 12 EXTENSION LENGTH 17 1/ 18 P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 1 OF 1 SY 092 Examples: Label/Part Number Identification (actual part identification on page 2) NOPY NOPY END END DEPTH ER-2L 1 With the canopy flanges installed with slightly loose screws, decide which end of the fixture run you will begin the canopy installation, then see above to select the correct canopy end panel, or canopy end. 2 SQURE = S RDIUS = R LEFT HND= L RIGHT HND = R Position the canopy retainer angle midway on the end canopy flange as shown, with the inside of the angle flush against the canopy flange. IF D-88 NOPY, be sure there are mounting holes in the canopy flange above and below the canopy retainer angle. Secure the retainer angle with a tab of masking tape. Repeat at the opposite end of the run. NOTE! This step does not apply if the MS metal canopy is to be used. NOPY END PNEL SQURE = S RDIUS = R SE SHELF DEPTH EPR818-27R UPRIGHT HEIGHT NOPY END PNELS / NOPY ENDS NOPY END DEPTH LEFT HND= L RIGHT HND = R EXTERIOR INTERIOR FINISH FIRST FINISH SEOND LEFT HND OR RIGHT HND PPLIES ONLY IF THE EXTERIOR ND INTE- RIOR FINISHES RE DIF- FERENT. EP/EP HRDWRE PK #7200-057 QTY ITEM DESRIPTION 1 ottom mounting bracket, 12" aluminum extrusion 2 # 8 x 5/8" Phillips flat head wood screw End panel hooks D 8 # 8 x 1/2" Phillips truss head sheet metal screw E 1 1" x " x 1" anopy retainer angle, galvanized F # 10 x 5/8" Phillips pan head sheet metal screw NOTE! Hardware pack is for one canopy end panel or one canopy end. if canopy end, skip to next page... IF NOPY END PNEL:, then proceed... E enter bottom retainer angle on the bottom edge of the panel. The down flange of the angle MUST be flush with the interior side of the panel. Screw the bottom angle to the panel as shown. Insert the down flange of the retainer angle between the base end cover and the base shelf...see page 1, at top. The rear edge of the panel must be flush against the upright. FINISH ODE: MO - MS SE SHELF SE END OVER P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282
NOPY SYSTEMS PGE 1 OF 1 SY 092 5 6 7 8 5 Insert a panel hook into the second upright slot from the top, mark hole locations and remove the panel hook. Drill a shallow pilot hole,1/8 bit, insert panel hook and secure to the end panel with screws, as shown. Repeat step 5 at 6 above the base shelf. Repeat step 5 with the remaining two panel brackets, equally spaced on the face of the upright. FIRST...screw the canopy retainer flange to the canopy end panel as shown. SEOND...pull the canopy tight against the canopy end panel and secure with screws as shown. IF NOPY END: Flush the top of the canopy end with the top of the upright...be sure the rear of the canopy end is flush against the upright Insert panel hooks into the second and seventh upright slot from the top, mark hole locations and remove the panel hooks. Drill shallow pilot holes with a 1/8 drill bit. Insert panel hooks and secure to the end panel with screws, as shown. Go to step 8, above, to secure the canopy end to the canopy. F SEOND NOPY END PNELS / NOPY F FIRST D D ENDS, ONT D P.O. OX 729 / TERRELL, TEXS 75160 / 972.56.57 / 800.776.29 P.O. OX 177 / GOODWTER, LM 5072 / 205.89.65 / 800.6.6282 # EN# ISION Y DTE 88 ISE LYOUT M 10/9/00 L002776 UPDTE ON NOPY PNEL J 11//0 # EN# ISION Y DTE