N ETWOR KS FHX 8-PORT FIBER ENCLOSURE USER MANUAL
Contents Safety Information... I Chapter 1 Installation Instructions... 1 1.1 Package Contents... 1 1.2 Carton Contents... 2 1.3 Labeling... 2 1.4 Installing Trunk Plate... 3 Chapter 2 Installing Modules... 4 Chapter 3 Trunk Leg Routing... 5 3.1 Standard Mode Shown... 5 3.2 Optional Mode Shown... 5 Chapter 4 Mounting the Housing... 6 4.1 Completing Installation... 8
Safety Information WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN DUST CAPS ON UNMATED CONNECTORS. CAUTION: Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. CAUTION: Care should be taken when opening or closing a fully loaded drawer in order to protect the fiber components. I
Chapter 1 Installation Instructions 1.1 Package Contents: Parts included with all enclosures: 6-Sliding tray pull-tabs 1-Label card 1-Trunk slack plate 2-Door latchs 4-M6 Nuts 2-Mounting brackets 4-M6x15mm Screws 1-Front cover Figure 1-1 FHX-1UP 01
1.2 Carton Contents Trunk slack plate Front cover Mounting bracket Door latch Sliding tray pull-tabs Dividing rail Label card Improved mounting brackets allow for depth adjustment in the rack. 1.3 Labeling Figure 1-2 Labeling options for the FHX Fiber Enclosures allow for identification to follow the EIA 606-B labeling standards. labels allow for ease of editing and label replacement when necessary. The labeling layout for the 1U enclosure on the inside of the front cover coincides with the port as shown in Figure 1-3. Figure 1-3 02
Insert the top half part of the buckle into the hole, press the spring on the lower half to make it fully inserted into the panel. Step 1 Insert the top half part of the buckle into the hole Step 2 Press the spring on the lower half to make it fully inserted into the panel. Step 3 Complete door latch installation. Figure 1-4 1.4 Installing Trunk Plate Install the trunk plate to the rear of the housing by sliding it onto the stud on each side and tightening the thumb screw to secure the plate in place. Removable Trunk Plate Screw Stud Figure 1-5 03
Chapter 2 Installing Modules Clean adapters and cables before mating (8-Port FHX MTP/MPO cassettes shown) Figure 2-1 Figure 2-2 When inserting the MTP/MPO cassette, there is a locating point as shown which can fix the cassette to avoid the crashing to door panel. Press the locating point to make the cassette moveable if needed. Figure 2-3 04
Chapter 3 Trunk Leg Routing Route fiber to the fiber cassettes as shown. Use enough cable length when making the loops to leave enough slack, so the cables are not put under tension when the drawer is fully extended. Use cable ties to secure fiber cords at the desired points as shown. 3.1 Standard Mode Shown (The top half part of trunk leg routing omitted for clarity) cable tie Figure 3-1 Completed Trunk Cable Installation NOTE: The cable ties should be untied when extend the drawer. 3.2 Optional Mode Shown Figure 3-2 05
Figure 3-3 a Chapter 4 Mounting the Housing Determine the desired height and location that will be inserted M6x15mm screws. a Figure 4-1 NOTE: Only the M6x15mm screws provided can be used. 06
Insert the M6x15mm screws (provided) into the desired holes as shown, and then use the nuts to tighten all screws. b b Figure 4-2 c c Install next two screws in center notch of mounting bracket, tighten all screws. Figure 4-3 07
4.1 Completing Installation d Record connectivity information on the label inside the front door. d Figure 4-4 e Close the front door. e Figure 4-5 08
Addresses, phone number and fax number also have been listed at www.fs.com. Please e-mail us at sales@fs.com or call us for assistance. All statements, technical information, and recommendations related to the products here are based upon information believed to be reliable or accurate.however, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact formore information.