VARIABLE SPEED BECH LATHE Instruction Manual Please read this instruction manual thoroughly and follow all directions carefully. 1
Important Safety Instructions READ ALL INSTRUCTIONS AND WATNINGS BEFORE USING THIS TOOL. Operator COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO ANY PRODUCT. THESE FACTORS MUST BE SUPPLIED BY THE OOPERATOR. PLEASE REMEMBER: 1. When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. 2. Keep work area clean. Cluttered areas invite injuries.' 3. Consider work area conditions. Do not use machines or power tools in damp, wet or poorly lit locations. Do not expose equipment to rain. Keep work area well lit. Do not use tools in the presence f flammable gases or liquids. 4. Keep children away. All children should be kept away from the work area. 5. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. 6. Stay alert. Never operate equipment if you are tired. 7. Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes might be impaired. 8. Do not wear loose clothing or jewelry as they can be caught in moving parts. 9. Wear restrictive hair covering to contain long hair. 10. Use eye and ear protection. Always wear. -ANSI approved chemical splash goggles when working with chemicals. -ANSI approved impact safety goggles at other times. -ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. -A full face shield if you are producing metal or wood filings and/or chips. 11. Keep proper footing and balance at all times. 12. Do not reach over or across running machinery. 13. Always check that adjusting keys and wrenches are removed from the tool or machine before starting it. 14. Do not carry any tool with your finger on the start button or trigger. 15. When servicing. Use only identical replacement parts. 2
Before Operation 1. Be sure the switch is OFF when not in use and before plugging in to wall outlet. 2. Do not use inappropriate attachments in an attempt to exceed the tool's capacity. Approved accessories are available from the dealer or machine maker. 3. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. 4. Check for alignment and binding of all moving parts. Broken parts or mounting fixtures and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 5. Do not use the tool if any switch does not turn off and on. Operation 1. Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do the job better and more safely at the rate for which it was intended. 2. Do not carry the tool by its power cord. 3. Always unplug the cord by the plug. Never yank the cord out of the wall outlet. 4. Always turn off the machine before unplugging. IF YOU QUESTION THE SAFE CONDITION OF THE MACHINE, DO NOT OPERATE IT! Electrical Grounding Instructions This machine has a three-prong plug(can choose), the third (round) prong is the ground. Plug this cord only into a three-prong receptacle. Do not attempt to defeat the protection the ground wire provides by cutting off the round prong. Cutting off the ground will result in a safety hazard and void the warranty. DO NOT MODIFY THE PLUG IN ANY WAY. IF YOU ARE NOT SURE ABOUT THE CONNECTIONS, CALL A QUALIFIED ELECTRICIAN. 3
IDENTIFICATION Starting Operation 1.Turn the switch(6)to the left for lathe function. The power (5)is light 2.Turn the emergency switch to the arrow direction, the speed showing screen will be on. 3.Push the start button (21), the spindle will be forward turning; the speed is 100r/min. Speed up and down button could control the spindle speed. 4. Turn the reverse button (25), the spindle will turn the direction to the opposite way. 5. When the spindle is running, push the Stop button (26), the spindle will stop. When push the start button (2) again, the spindle will back to the formal condition. 6. When the spindle is running, push the emergency stop (4), the spindle stop, the speed showing screen (22) will be off. 7. The headstock eyeshield (7) will control the spindle on and off. 8. Turn the switch(6)to the right for mill function. The power (5) is off. Then you may use the mill head. (Operational) 4
1. Thread Pitch Gearing &Speed Charts 14.Tool Post Lock Handle 2. Speed Up 15.Compound Slide Hand wheel 3. Machine ID/Safety Label 16.Tailstock Center 4. Emergency Stop Switch 17.Tailstock Clamp Bolt 5. Lathe Power Indicator Light 18.Tailstock Axis Alignment Indicator 6. Selector Switch 19.Tailstock Barrel Hand wheel 7. Headstock Eye shield 20.Tailstock Center Lock 8. Lathe Chuck 21.Start Button 9. Carriage Feed Hand wheel 22 Speed Showing Screen 10.Cross Slide Hand wheel 23 Forward Button 11.Automatic Carriage Feed Lever 24 Speed Down 12.Compound Slide 25 Reverse Button 13.Tool Post 26 Stop Button INITIAL START Turn the Selector Switch (F) to Lathe position. 5
PART NO. DESCRIPTION PART NO. DESCRIPTION 201 PHLP HD SCR M5-8*10 228 LOCK WASHER 5MM 202 PHLP HD SCR M3. 5*14 229 EXT TOOTH WASHER M5 203A EMERGENCY STOP SWITCH 230 PHLP HD SCR M5-0.8*16 205A FWD/REV SWITCH 231 SPINDLE CENTER MT3 207A LABEL 232 3-JAW CHUCK D=125MM 208 CONNECTOR 233 EXT RETAINING RING 6MM 209 ROUND NUT M27*1.5 234 PHLP HD SCR M5-.8*12 210 SPINDLE PULLEY 235 PHLP SCR M5-.8*12 211 SPINDLE GEAR 236 PHLP HD SCR M10-1.5*25 212 OIL RING 237 SUPPORT 213 PHLP HD SCR M5. 8*8 238 LIMIT BLOCK 214 SPINDLE SPACER 239 CHUCK GUARD 215 BEARING 32007 240 FIXING SUPPORT 216 SPINDLE BOX COVER 241 SMALL SHAFT 217 HEX NUT M4-0.7 242 COMPRESS SPRING 218 PHLP HD SCR M4. 7*35 243 FLAT WASHER 6MM 219 PIN SHAFT 244 HEX NUT M6-1.0 220 BOX FOR MICRO SWITCH 245 PLATE FOR SWITCHES 221 HEAD STOCK BODY 246 FLAT WASHER 10MM 222 FIXING NUT 247 PHLP HD SCR M5-.8*8 223 ROTATABLE SPACER 248 MICROSWITCH 224 KEY 4*40 249 3-JAW CHUCK FLANGE 225 SPINDLE 250 HEX BOLT M8-1.25*30 226 PHLP HD SCR M6-1 *16 251 PLUG BOLT 227 FRONT BEARING COVER 252 HEX NUT M10-1.5 6
PART NO. DESCRIPTION PART NO. DESCRIPTION 901 HEX BOLT M8-1.25*30 928 BOLT M8*25 902 FLAT WASHER M8 929 SCREW M5*8 903 AC MOTOR 930 FAN-SUPPORT 904 KEY 5*40 931 WASHER 905 WASHER 932 SCREW M6*35 906 DRIVER PULLEY 933 BOLT M10*25 907 KEYWAY SHAFT SPACER 934 NUT M3 908 MOTOR PULLEY 935 PULLEY SUPPORT 909 CHECK RING 936 PROTECT COVER 910 PHLP HD SCR M6-1.0*30 937 SCREW M6*12 911 OIL CUP 6 938 NUT M12 912 GREAT WASHER 939 POWER SOCKET 913 COUNTER PULLEY 940 BIG WASHER 12MM 914 SLIDE BEARING 941 SCREW M3*6 915 ARM SHAFT 942 MOTOR COVER 916 BEARING ARBOR 943 SPRING WASHER 6 917 TENSION PULLEY 944 TIMING BELT 1.5*124*15 918 BEARING 6001 945 V-BELT O737 919 SPACER 946 NUT M5 920 LOCK WASHER 6MM 947 POWER PLUG 921 EXT RETAINING RING 12MM 948 MOTOR SEAT 922 EXT RETAINING RING 28MM 949 SCREW M6*20 923 PIVOT 950 WASHER 3 924 PIVOT SPACER 951 MOTOR PROTECT COVER 925 FLAT WASHER 10MM 952 PC BOARD 926 HEX NUT M10-1.5 952 SCREW M3*16 927 PHLP HD SCR M3-14 7
8