Installation Guide 84 H and 95 H
Stacker Bracket Connectors for topper of the wall system Step 1: (for 95 H and 108 H only) Attach glass topper to the wall system using the bracket shown (84 H wall system will not need a topper). Please attach stacker brackets and topper before putting panels together. Topper Stacker Bracket Stacker Bracket Screws (will be screwed into bracket from inside, should be done before frame is put together) *95 H wall system will have a 11 H topper *108 H wall system will have a 24 H topper 1
Installing Wall Starter Wall Starter Track No pre-drilled holes. Please use sheet metal screws and tap holes through frame. 1 1 Fix the side groove into wall 40 mm adjustable depth Wall Starter A mill away 50mm A Insert the side pole to the side groove. Side pole is processed as photo and fixed with panel connectors. 2
Direct Wall Mount Leveling and Connecting Your 1st Panel to a Wall Starter Step 3 Use M8*40 bolt to connect side pole and frame Step2 Adjust the adjuster 5mm up to keep space for adjustment in the further assembling *Make sure it s level 5mm Leveler 3
Direct Panel Mount Screws straight into the wall 5mm Leveler 4
2. Connect the frames by M8*30 bolt Top Track! same height 1. Adjust all frames into same level 5
*All connectors simply bolt into panels. 4 ways connection 3 ways connection Straight Connector 2 ways connection 120 degree 2 ways connection 120 degree 3 ways connection Connect the partition and column by M8*20mm bolt 6
End Trim Attach End Trim to Wall system No pre-drilled holes. Please use sheet metal screws (gold screws) and tap holes through frame. Gold Screws 7
90 L Installing Swinging Door Frame How to Fix the Door Frame: 1. Fix the door frame material (45 cutting) with enhanced pole. 2. Fix the left and right door frame material with partition frame with screws in through the panels into the 3. Fix the top door frame material with L brackets, and insert it to the left and right door frame material. 4. Fix the partition frame above the door to the left and right partition frames. 5. Fix the hinges and sealings. 1 Door Frame with Partition Frame Door Frame with Side Pole Fix the L-Shape Aluminum Bracket Screw in through the panel into the door frame 5 2 L 3 4 8
1. Arrange Door Frame pieces on the floor in the correct positions that they will be put togther. TOP Door Frame Assembly A. FILLER SIDES FILLER B. 2. A. Screw in Top piece to side pieces using 1 screws (not self tapping). B. Then insert Fillers into sides with groove side up. 3. Insert Door Frame 59
90 4. Make sure Door Frame is level Door Frame Assembly L L 5. While tiles are o he wall, screw in through the panel to the frame with 1 1/2 self tapping screws. (7ft H walls this is the final step for the door frame assembly. 8ft H walls need to be screwed in from the top as well.) * 8ft 7ft *Only screw door frame in from top if setup is 8ft High 10
Swing Door Lock Assembly How to define door orientation Assembly Step One screw Left Open Door Right Open Door lock body door body Assembly Step Two Assembly Step Three 3 1 2 buckle groove lock buckle screw 11
Installing the tile hook Screws Hook L R R L Fix the tiles 12
Top Groove Panel Stabilizer *May sometimes be needed to cut to size. 1 1/2 Sheet Metal Screws 1 1/2 Sheet Metal Screws 7 H Custom Panel 84 11/16 (with top cap) 83 3/8 2 1/2 13
Top Groove Panel Stabilizer *May sometimes be needed to cut to size. Cut stabilizers to overlap seam of panels Do not let stabilizers connect at the seam of the panel frame 14
1. Screw in Sliding Door Track Clips into grooves between panels. (Door Rail must be placed 83 3/4 from the ground measuring from the bottom of the rail to the ground.) 2. Sliding Door Assembly Place Sliding Door Rail onto screwed in Sliding Door Rail Clips and screw in from below. Door Rail must be placed 83 3/4 from the ground. A B 83 3/4 83 3/4 C B 3. Place Sliding Door Bottom Track on floor using double sided tape, 4. After inserting the Sliding velcro, or glue; Lining it up with the Door into the rail, Secure Stopper Door Rail. Then proceed to place in on the end. Sliding Door. D 5. Place Sliding Door Rail Finish Cap(s). Parts: E A B C D E 15
! FINAL CONNECTION IS DONE BY A LICENSED ELECTRICIAN. WARNING: Risk of Fire or Electrical Shock. As with all non-directional systems, Do Not electrically connect panel to more than one supply source. Always determine that the panel is electrically connected to one and only one source of supply. Before using any equipment, check the entire system for polarity, continuity, and grounding integrity. Electric Setup Quad Power Modual 8w - 4c Flex Cables red in 3 1, 5 4, and 68 FIG 1 ***Outlet size: 325*** 3 H Blue 3 G Green/Yellow 1-2-4 G Green 3 N Gray 1-2-4 N White 1 H Bla ck 2 H Red 4 H Pink 3 IG 2 1 4 Base Power Feed New York City Version of base power-in New York City versions of the cable-management panels are available to comply with the special installation requirements of the New York City electrical code. Chicago Panels sold with NO ELECTRIC. Power Supply Connection The Power System is an eight wire system consisting of four individual circuits rated at 20amps/120 volts maximum. Circuit 1 (black), circuit 2 (red), and circuit 4 (pink), are served by a system neutral (white) and an equpiment ground (green). Circuit 3 (blue) uses an isolated neutral (gray), and an isolated ground (green/yellow). The system may be supplied by a three phase power system with four individual circuits rated 20 amps/120 volts maximum, or as perimtted by local code. Building Electric In Feed When connecting electric pass throughs to power moduals, please make sure ARROW is up! Base Power Feed Hinged Racetrack door open to show area for electric and wired management Outlet Layout Options: O1 O2 Shown with Electric Module and Data O3 Shown with Electric (you can order 1, 2, or 3 and dedicated outlets) O4 O5 OUTLET - BLANK - BLANK OUTLET - OUTLET - BLANK OUTLET - OUTLET - OUTLET OUTLET - DEDICATED* - BLANK O6 *PLEASE NOTE: Orange is used to represent the Dedicated Outlet. The Dedicated Outlet color is BLACK. OUTLET - DEDICATED* - OUTLET BLANK - DEDICATED* - BLANK SAPPHIRE Cubicles come with Style #325 Outlets. 16
Data Setup Options DM1 DM2 DM3 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 - Blank - Blank - Blank CAT 6 - CAT 6 - Blank - Blank CAT 6 - CAT 6 - CAT 6 - Blank DM4 DM5 DM6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 CAT 6 - CAT 6 - CAT 6 - CAT 6 CAT 6 - Phone Jack - Blank - Blank CAT 6 - CAT 6 - Phone Jack - Blank DM7 CAT 6 CAT 6 CAT 6 CAT 6 - CAT 6 - CAT 6 - Phone Jack All Modules can be customized to customers specifications. Please call to review options with one of our sales representatives. Color of jacks may vary. 17