SELECTION CHART Amplifier Unit Shape Power supply Output AC/220V 0/60Hz Relay Contact: SPDT AC20V 2A / DC30V 3A Solid State:Open-Collect or 0mA Max. MDA - 00 Sensor head Shade Minimum Detectable object 0 2.0mm dia. steel ball MSC-00 7 2.mm dia. Steel ball MSC-07 0 3.0mm dia. steel ball MSC-0 0 X 0 (LXW).0mm dia. Steel ball MSR-0 200 X 0 (LXW) 7.0mm dia. steel ball MSR-200 Y-02
SPECIFICATIONS Amplifier Unit Power Supply Power Consumption Sensitivity adjustment AC /220V +% 0/60Hz 3VA Max. By sensitivity selector switch and fine-adjustment trimmer Timers Solid-State Relay Contact Normal/OFF delay 40ms ( by switch ) ONE-SHOT 40ms ( fixed ) Time interval of detection (Note) Solid-State Relay Contact Normal OFF delay 7ms Max. 7ms Max. 2ms Max. Control Output Sensor Adapt Solid-State Relay Contact Open-collector:0mA max. ( DC40V ) SPDT 20VAC 2A ( resistive ) ; 30VDC 3A ( resistive ) All models of Passage Confirmation Sensors Correct Cable length Output Status Indicator Operating Temperature Operating Humidity Isolate Resistance Voltage Resistance Vibration Resistance Shock Immunity Protection Category Weight By switch NO/NC Changeable ( By switch ) Power Indicator & Operation Indicator - C ~ + C 3~ 8%RH 0M Max. ( 00VDC MEGA ) one time across power terminal & exposed, two times at all terminal ( non-contact output and sensor ). AC,00V, 0/60Hz min one time across power terminal & exposed metal, two times at all terminal ( non-contact output & sensor; contact ). directions,2 hours respectively to Hz,.mm double amplitude in X, Y, and Z 0m/s2G in X, Y, and Z directions,3 times respectively IP30 Approx.300g Note: Time to detect minimum size Object, Longer detection time if object is larger. Y- 03
Sensor head Item Detection Area Detection Object Type MSC-00 MSC-07 MSC-0 0mm dia. 7mm dia. 0mm dia. Moving ferrous metal ( sensibility of non-ferrous metal is low ) Min. Target 2.0mm dia. Steel ball 2.mm dia. Steel ball 3.0mm dia. Steel ball Operating Temperature -2 C ~ +70 C ( Without icing ) Operating Humidity 3-90%RH Isolate Resistance Voltage Resistance Vibration Resistance Shock Immunity Cable Weight Protection Category Housing Material Sensor Face Except for expose head & isolate wire with connection Except for expose head & isolate wire with connection to Hz,.mm double amplitude in X, Y, and Z directions,2 hours respectively 0G in X, Y, and Z directions,3 times respectively 3m ( Coaxial Cable ) Approx.430g Approx.800g Approx.200g IP67 ALUMINIUM ABS Item Detection Area Detection Object Min. Target Type MSR-0 MDS-L200 0x0mm 200(L)x0(W) Magnetic metal ( The sensibility of non-magnnetic metal is not well ).0mm dia. Steel ball 7.0mm dia. Steel ball Operating Temperature Operating Humidity Isolate Resistance 0M -2 C ~ +70 C ( Without icing ) 3-90%RH Voltage Resistance Vibration Resistance Shock Immunity AC,000V/min to Hz,.mm double amplitude in X,Y,and Z directions,2 hours respectively 0G in X,Y,and Z directions,3 times respectively Cable 3m ( Coaxial Cable ) Weight Approx.,300g Approx.2,0g Protection Category IP67 Material Housing Sensor Face ABS ABS ALUMINIUM Y- 04
PRECAUTIONS FOR PROPER USE Disturb of the around metal When mounting on a steel base, follow the guidelines below to prevent detection of the mounting material. Dimension l m Moving metal MSC-00 MSC-07 MSC-0 0 30 200 40 300 0 m MSR-0 MSR-200 UNIT: mm l l When mounting on an iron base is necessary, follow the guidelines given below must be satisfied. Otherwise, it may be resulted in a mistake operation. MSC-00 MSC-07 Drop through mount: Drill a With min. diameter 0f 2mm. hole 34mm Max. 2 MSR-0 MSC-0 Drop through mount: Drill a With min. diameter 0f 0mm. hole 0 40 2mm Max. 40 MSR-200 Note: The type of MSR-0.0 & MSR-200 7.0 should be mounted on the surface in order to minimize the interference of metal. Y- 0
Interference of sensor each other When installing 2 or more sensors of the same model in close proximity, it is necessary to connect the grounding screw to the machine ground and to maintain spacing greater than the distance shown in the following table to prevent interference. Dimension Series(d) parallel(d2) MPC-00N32.0 0 30 MPC-07N32. MPC-0N33.0 MPR-0N3.0 MPR-200N37.0 200 300 40 0 UNIT: mm Other precautions: The operation of the sensor is stable to 2 seconds after the power is applied. Do not use Sensor signal immediately on power-up. In order to prevent interference, keep exposed cable wire mm or less.(see diagram) When target has stopped or a wire break occurs, the output is ONE PULSE(40ms) Don't touch the sensor's active face at the status of high sensitivity, because atouchbyhandwillbedetected. mm Max. CHARACTERISTICS Target speed-size chart MSC-00 Speed V(m/s) 20 Iron brass Target (m) 20 Speed V(m/s) MPC-07 20 Iron brass (m) 20 Target Check domain 4 3 2 Check domain 4 3 2.4 0 2 3 4 6 7 8 Target size 0. 9 (mm).4 0 2 0. 3 4 6 7 8 9 Target size (mm) Y- 06
MSC-0 Output residuary voltage Speed V(m/s) 20 Target (m) Iron 20 brass Residuary voltage (V).2..0.4 0 2 3 4 Check domain 6 7 8 Target size 9 4 3 2 0. (Mm) 0.9 0.8 0.7 0.6 3 7 30 0 700 300 00 ACTION CHART Detects object PASSAGE NO Action method N.O. N.C. Timer shift Solid-contact Relay-contact Detects indicator Power indicator TIMER NORMAL ON OFF ON OFF ON OFF ON OFF B B A A power off Note : When a target is passing, the Output of the contact is on, while the non-contact is Changeable ( N.O.or N.C. ). Note 2: Output of the contact is oneshot type. It can output a 40ms fixed pluse-width Independent of the time the target present. A: 40ms(OFF DELAY) B: 40ms(ONE SHOT) Y- 07
F2LP-W0M F2LP-W7M F2LP-W0M F2LP-W7M Y- 08
TH- TH-20 Y- 09