Page1 easyrescue-divepro - Transponder Manual easyrescue-divepro Diver Locating System Product No.: A040-DP Rev. 1.1 Sigmundstrasse 180 90431 Nürnberg Tel. +49(0)911 37663830 info@weatherdock.de www.easyais.de
PLEASE READ THIS FIRST! Page 2 of 34 Safety Precautions The easyrescue-diveprotransponder contains Li-Ion batteries. When the device is used at temperatures outside the limits of -20 C and +55 C, the useful battery capacity is reduced. Keep the device away from hot environments, because at temperatures of more than +70 C the batteries inside the easyrescue-diveprocould cause damage. Li-Ion batteries shall be given to the recycling process and should not be given to the home garbage. The easyrescue-diveproproduces electromagnetic fields, which could interfere medical devices. For safety reasons store this device so that children cannot reach it. The manufacturer is not responsible for damages or failures that are caused by the easydivepos, damaged battery pack or misuse by the user. Use this device only together with certified equipment. Other equipment could damage the easydivepos. Clean this device with a clean, dry and soft blanket. Do not use aggressive or acid liquids and chemicals for cleaning. Do not open the device on your own. Unpermitted opening of the easyrescue-diveprocould damage the device and the warranty is lost. LICENSING IMPORTANT: In most countries the operation of a VHF unit unsing the marine band is included under the vessels marine VHF license provisions. Please contact the relevant authority in your country for more information. In accordance with a policy of continual development and product improvement the easyrescue-diveprohardware and software may be upgraded
Page 3 of 34 from time to time and future versions of the easyrescue- DivePromay therefore not correspond exactly with this manual. When necessary upgrades to the product will be accompanied by updates or addenda to this manual. Please take time to read this manual carefully and to understand its contents fully so that you can install and operate your system correctly. Information contained in this manual is liable to change without notice., disclaims any liability for consequences arising from omissions or inaccuracies in this manual and any other documentation provided with this product. DISCLAIMER THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Page 4 of 34 ATTENTION: PLEASE USE THE easyrescue-diveprocarefully AND NOT UNINTENDED. ALSO THE easyrescue-diveprowill NOT OPERATE AUTOMATICALLY. IT MUST BE INITIALISED BY THE USER IN CASE OF EMERGENCY All trademarks mentioned in this document are the property of their respective owners. Copyright 2011,. Copying of this document, and giving it to others and the use or communication of the contents thereof, is forbidden without express authority. Offenders are liable to the payment of damages. Sin nuestra expresa autorización, queda terminantemente prohibida la reproducción total o parcial de este documento, así como su uso indebido y/o su exhibición o comunicación a terceros. De los infractores se exigirá el correspondiente resarcimiento de daños y perjuicios.
DIRECTORY Page 5 of 34 1. SHORT DESCRIPTION... 7 2. ACTIVATORS AND INDICATORS... 9 2.1. ACTIVATING ELEMENTS...10 2.1.1. Button "ON"...10 2.1.2. Button "ALERT"...10 2.2. INDICATORS...10 2.2.1. GPS LED...10 2.2.2. ON LED...10 2.2.3. ALERT LED...11 2.2.4. White Flash LED...11 3. OPERATION INSTRUCTION... 12 3.1. ACTIVATION "ON"...12 3.2. ACTIVATION "ALERT"...14 4. INSTALLATION TIPS... 16 5. CHARGING THE BATTERIES... 18 6. PROGRAMMING... 20 6.1. PROGRAMMING STATIC DATA...21 6.2. ADMINISTRATOR SETTINGS...25 6.2.1. MMSI (Alert)...25 6.2.2. MMSI (ON)...26 6.2.3. Frequencies...26 6.3. FIRMWARE UPDATE...26 7. TECHNICAL DATA... 28 8. DECALARATION OF CONFORMITY... 30 9. BOX CONTAINS... 31 10. AVAILABLE ACCESSORY... 32 11. FAQ... 32 12. ANNEX RANGE TEST RESULTS... 33
Page 6 of 34 13. SUPPORT... 34 14. WARRANTY... 34 Revision of the operation manual Rev. 1.0 Author: Jürgen Zimmermann, 08. February 2012 Rev. 1.1 Author: Max Schuster, 4 th December 2014 C0ngratulations! Thanks to purchase a unit from the. This testifies your high technical competence
Page 7 of 34 1. SHORT DESCRIPTION Figure 1 The easyrescue-divepro is a portable battery powered AIS- Position transmitter with an integrated GPS-receiver. The device is intended for the use in locating operations. The easyrescue-divepro operates as a VHF-Transmitter and it can be activated in two situations by pressing two different buttons:
Page 8 of 34 (A) The locating object wants to inform the searching ship about its position. So the ship, it belongs to, can search and find the locating object. This happens on a frequency in the marine VHF band, which is assigned by the authority of the country. (B) Alerting in case of emergency the units operates as an AIS-SART (AIS - Search-and-Rescue-Transmitter). The range depends on the height of the transmitters antenna over sea level. The range is approx. 10-15 nautical miles, if the height of easyrescue-divepro s antenna 1m and up above sea level assumed that the receiving antenna is at a height of 5m and up (ship's VHF antenna). The Li-Ion battery pack provides a capacity that ensures an operation time of more than 120h, when activated. This device maintains water tightness down to 10m depth, not unduly affected by seawater or oil and is resistant to sunlight. It withstands drops from a height of 20 m into water. The Li-Ion batteries can be recharged easily using the charging station that can be purchased by an authorized distributor.
Page 9 of 34 2. ACTIVATORS AND INDICATORS Figure 2
Page 10 of 34 2.1. Activating elements 2.1.1. Button "ON" Pressing the button ON the easyrescue-divepro enters the 'Identification" mode (transmitting locating object's position). If this button is pressed again for 3 seconds, the normal mode will be terminated and the device is turned off. 2.1.2. Button "ALERT" With the button "ALERT the device can be activated in case of emergency. AIS-SART messages cause an alarm at the receiver side (i.e. shore base station or mobile ship station). The ALERT mode can be terminated by pressing the BOTH button for 3 seconds. The easyrescue-divepro switches totally off then. 2.2. Indicators 2.2.1. GPS LED The green LED with the marking GPS is blinking, when the device receives GPS signals and is able to get a position fix. If the GPS LED does not blink, there is not GPS reception possible. 2.2.2. ON LED The yellow LED with the marking ON" is blinking, when the easyrescue-divepro is activated in case of identification (transmitting locating object's position and additional status information).
2.2.3. ALERT LED Page 11 of 34 The green LED with the marking "ALERT" is blinking, when the easyrescue-divepro is in alert mode. 2.2.4. White Flash LED The bright white flash LED is used for visual locating purpose, especially at night times.
Page 12 of 34 3. OPERATION INSTRUCTION 3.1. Activation "ON" Press the button ON. Figure 4 The ON-LED starts flashing every 2 seconds. As soon as a GPS position is available the GPS-LED start flashing
Page 13 of 34 too. The easyrescue-divepro starts transmitting a burst of VHF messages. The reporting interval can be selected by the easyrescue-divepro Programming Tool (see later). The reporting interval can be 3 minutes, 1 minutes, 30, 10 and 6 seconds. The yellow LED also indicates the charge status of the battery. If the battery is full, the LED would flash once. If it is half full, then twice and in case it is becoming empty three times. Transmitted information: Unit-ID: (9 digits) Position : Latitude & Longitude with a resolution of 1/10.000 of a minute, Speed over ground (SOG) : drift due to currents, Course over ground (COG), Diving Vessel / Divers name: (20 characters) Vessels destination or area of activity: (20 characters)
Page 14 of 34 3.2. Activation "ALERT" Figure 3 Press the button ALERT and take care that the easyrescue-divepro has got line of sight to the sky. This ensures best GPS reception conditions. The ALERT-LED starts flashing every 2 seconds. As soon as a GPS position is available the GPS-LED starts
Page 15 of 34 flashing too. The easyrescue-divepro starts transmitting a position report every minute. The unit is transmitting into the international AIS, which ensures most effective help from other ships in vicinity. If the unit loses a GPS position fix, then the GPS-LED stops flashing but the easyrescue-divepro will transmit the last known position. The status of the battery is the same as described above. Transmitted information : Unit-ID: (9 digits) Position : Latitude & Longitude with a resolution of 1/10.000 of a minute, Speed over ground (SOG) : drift due to currents, Course over ground (COG), Diving Vessel / Divers name: (20 characters) Vessels destination or area of operation: (20 characters) Search-And-Rescue ALERT The ALERT-mode can be terminated by pressing both buttons for more than 3 seconds. The unit goes back to normal operation (ON-Mode).
4. INSTALLATION TIPS Page 16 of 34 To install the easyrescue-divepro the unit holder as you can see in picture below. You can mount these on the pole of your buoy. So you can use it for a variety of poles. If you have access to board supply voltage, you can connect the cable to 12V / 24V. So the unit will be powered through
Page 17 of 34 this power supply. In case of power supply outage the unit will continue operation using the integrated rechargeable batteries without any interrupt.
Page 18 of 34 ATTENTION: Do not have a pole close to the antenna (left figure). This would significantly reduce the radiated power of the VHF signal. The right figure is perfect. 5. CHARGING THE BATTERIES The easyrescue-divepro can be recharged in the Battery- Charger. The Battery-Charger is an accessory with the product number A121 and can be purchased by your distributor. Inside the easyrescue-divepro there are Li-Ion batteries, which have got a capacity of around 120 h operation time. These batteries are high quality batteries with very low self discharge. So you can store the fully charged easyrescue- DivePro for more than three month without a significant loss in capacity.
Page 19 of 34 Put it into the charging station as picture above. The nose on the upper end of the station will fix the device. Place the easyrescue-divepro into the Battery-Charger. The battery charger must be connected to DC power supply (12V / 24V, 1A). When charging, the yellow LED is on continuously. The green LED is on, when the batteries are full charged. When the batteries are almost empty, the full charge process lasts approximately 4 hours.
Page 20 of 34 6. PROGRAMMING The easyrescue-diveprocan be configured with information, that is included in the VHF messages and different settings. The Unit-ID is a 9-digit figure like the MMSI, known from the AIS system. It is a unique number, programmed by an authorized body! In order to program the easyrescue-divepro you need the USB-Programmer device A124. The USB-cable shall be connected to a PC or laptop.
Page 21 of 34 With the Programmer device comes a CD-ROM with the installation software for the PC. Insert the CD-ROM into your PC or Laptop and start the setup program. On the Windows-Desktop you will see the icon of the easyrescue-diveproprogramming software. When you double-click that icon the following program window will open: Figure 4 6.1. Programming Static Data Now you have to insert the easyrescue-divepro into the programmer socket, which is connected to the USB port of
Page 22 of 34 the PC. You see all LEDs are turning on until only the white LED remains on. Now the unit is ready for connecting with the PC software. Please select the right COM-Port and press "Connect". After that the following picture will occur: Figure 5 The contents shown above are just an example. The MMSI can only programmed by an administrator. In case of changing the VHF frequency channels, which might be necessary in some countries, contact you distributor. He is authorized to change the frequencies.
Page 23 of 34 You can enter a name, which could be the name of the captain or vessel. You can also enter the area of activity of the vessel, which could be the home area. You also have the possibility to change the reporting rate to following values : 3 minutes, 1 minute, 30, 10 and 6 seconds. ATTENTION: The reporting rate has effect on the battery operation time: 3 minutes => 180 hours, 1 minute => 120 hours, < 1 minute => 24-36 hours To store all the data and settings press "Save to DivePro ". After successful programming the following window occurs:
Page 24 of 34 Now you can press on "Disconnect" and remove the unit out of the socket. The unit will turn off automatically after 10 sec. The previously programmed data are stored in a non-volatile memory. So the easyrescue-divepro need not to be programmed again and again. The data remain even, if the device is powered off. But you can change the contents later by repeating this process.
6.2. Administrator settings Page 25 of 34 When you are administrator, that means you are authorized to do frequency changes, then you have got a "dongle" (blue USB-stick). The dongle has to be in USB port before starting the Programming-Tool. Now you can go to the administrator tab: Here you can change the unit identifiers and the frequencies. 6.2.1. MMSI (Alert) This identifier is sent out, when you have pressed the "Alert" button. The unit is transmitting on international AIS
Page 26 of 34 frequencies. All AIS-vessels will get an alert message on their plotters together with your position. It should always start with "97022...", because this is the official numbering of AIS- SART. We strongly recommend not changing this number. The manufacturer has provided a unique number here. 6.2.2. MMSI (ON) This is the MMSI, which is sent in normal operation. You can choose any 9-figure number you want, because the unit is sending on proprietary frequencies (NOT on AIS). 6.2.3. Frequencies Here you should enter the frequency you have got a license for. It could be a a single frequency, so both channels have the same value. Or you have got two frequencies, which are used in an alternating way, as known from the AIS. 6.3. Firmware Update With the Programming Tool you have the possibility for updating the internal software of the easyposalert (called firmware). So you can keep the unit always up to date. For updating press on "File => Update", then the Update window occurs.
Page 27 of 34 You select the new update file (extension *.wdc) by clicking on (1). For starting the update process just click on (2). See following window.
Page 28 of 34 7. TECHNICAL DATA Parameter Value Dimension 130 x 30 x 70 mm Weight 380 g DC supply rechargeable Li-Ion-batteries Locating object locating: Marine band programmable by distributor : Frequency 155.450... 162.025 MHz (contact local authority for frequency assignment) Radiated Power > 2 W (typ.) (min. 500 mw) GPS receiver Approved to IEC 61108-1 VHF-Antenna extended, vertical polarized min. 120 hours with fully charged Operating time batteries min. 3 month without significant Battery storage (fully charged) loss of charge Operation temperature range -10 C to +55 C Storage temperature range -30 C to +70 C Display 3 LEDs and a "Flash"-LED Activators 2 buttons IEC 61097-14, IEC 60945, ITU-R Standards M.1371-3, IMO Res. MSC.246(83), IEC 61108-1 Msg. 1: AIS Positions Report. Supported AIS messages Msg. 5: AIS Static Report. Msg. 14: AIS Alerting Message.
Parameter Environment Value Page 29 of 34 Waterproof: Down to 10m water level Exterior Finish: Highly visible yellow Compass safe distance: 80cm Mechanical shock Drop into water: 20 m Drop on concrete surface: 1m Thermal shock Temperature difference: 45 K Resistance Oil, seawater and sun light resistant
Page 30 of 34 8. DECALARATION OF CONFORMITY easyposalert (portable position transmitter) Identifing and Alerting transmitter Part No. Manufacturer: A040-DP 1) Proved performance: Up to 8-12nm by a ship with VHF receiver and an receiving antenna height of approximately 5 m height Up to 40 nm (from a helicopter (altitude 1000 ft) Very compact and rigid. 10m water depth level approved 2) Standards: easyposalert is based on AIS SOTDMA technology. The easyposalert is is approved by the following standards: ITU-R M.1371 EN 60945 (2002) IEC 61097-14 (2010) IEC 61108-1 (2003) MSC.246 (83) (IMO Resolution) R&TTE Directive 1999/5/EC BSH-Type Approval No.: BSH/4615/4361565/10 easyposalert s technical specification is according to above standards, with the exception of the ON feature and its functionality.
9. BOX CONTAINS Page 31 of 34 easyposalert transmitter, fully functional Manual
Page 32 of 34 10. AVAILABLE ACCESSORY Battery charger A121 Programmer A124 with programming software easyrescue- DivePro VHF receiver VHF antenna Please contact specialized distributors. 11. FAQ Problem Reason Solution Cannot activate the device. Battery change Battery is empty Recharge the Li-Ion batteries only with the charger station for the easyrescue-divepro The unit is fully potted and so there is no possibility to change the batteries.
Page 33 of 34 12. ANNEX RANGE TEST RESULTS
13. SUPPORT Page 34 of 34 14. WARRANTY This product is warranted to be free from defects in materials or workmanship for 24month from the date of purchase. Within this period, will at its sole option repair or replace any components that fail in normal use Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to abuse, misuse, accident or unauthorized alteration or repairs. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. IN NO EVENT SHALL TECHAF CORPORATION BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. retains the exclusive right to repair or replace the unit or software or offer a full refund of the purchase price at its sole discretion. Such remedy shall be your sole and exclusive remedy for any breach of warranty.