Submittal Review TO: Pavilion Construction DATE: 07.20.2015 JOB NO.: 1484P 4700 SW Macadam Ave Suite 200 ATTENTION: Riley Tobin Portland, OR 97239 RE: BSD Sunset High School Concession Stand/Interior Renovations Package 1 Submittal: 10 28 00 Toilet, Bath and Laundry Accessories Approved Approved As Noted Revise as Noted/Resubmit Rejected/Resubmit As Specified No Action Required Submittal Not Requested/Returned Without Review Approval is for conformance with information given and the design concept expressed in the Contract Documents. Contractor is responsible for quantities and dimensions to be confirmed and correlated; for fabrication process; for means methods, techniques, sequences and procedures of construction; for coordination of the Work; and for all safety aspects of performing the Work. Approval does not modify the Contract Documents and approval of a specific item does not indicate approval of an assembly of which the item is a component. Specification Section Title Notation 102800 1.3A Product Data: Mirrors, Under-Lavatory Guards Not Submitted. Resubmit 102800 1.3A Product Data: B-5181, B-5806, B-6806 Approved 102800 1.3B Product Schedule No Action Required 102800 1.3C Maintenance Data No Action Required 102800 1.3D Warranty Not Submitted. Resubmit Summary Comments: 1. Mirrors and Under-Lavatory Guards have not been submitted. Resubmit 2. B-5181 Folding Shower Seat, B-5806 Grab Bar, and B-6806 Grab Bar are approved. 3. The requirements of 102800 1.3B have not been met. If G.C. does not intend to submit a product schedule, they are to proceed at their own risk. 1001 SW 5 th Ave. // Suite 1100 // Portland // OR 97204-1127 // P: 503.535.0707 // www.blrb.com
Sunset High School 13840 NW Cornell Rd. Portland, OR 97229 To: Attn: BLRB ARCHITECTS, P.S. RICHARD HIGGINS 1001 SW 5TH AVE., SUITE 1100 PORTLAND, OR 97204 Date: Contact Phone: Contact Email: 07/17/2015 503-535-0707 RHIGGINS@BLRB.COM CC d: SUBMITTAL TRANSMITTAL FOR APPROVAL Submittal #: 39 Rev.#: 0 In Accordance with Specification Section #: 102800 This is a submittal for Toilet, Bath and Laundry Accessories items per the table below as reviewed and noted by Pavilion Construction NW, LLC, and provided by W. H. Cress. Please provide a response to this submittal by 07/22/2015. Pavilion Status: Sent/Submitted Notes: Submitted By: Email Address: Riley Tobin rtobin@pavilionconstruction.com Phone: Fax: (503)290-5005 (503)244-1810 SUBMITTAL RESPONSE Architect s Response Proceed Proceed, as noted Revise and Resubmit Material Return without Review Schedule Tracking Date Date Date Date Received from Sub/Sup Requested to be returned Returned from Architect Returned to Sup/Sup 07/22/2015 Comments: PAVILION CONSTRUCTION LLC BY: CONFORMS WITH SPECIFICATIONS NOT CONFORMING CONFORMS WITH NOTES PARTIAL SUBMITTAL Riley Tobin DATED: 07/17/15 This submittal has been reviewed for general conformance with contract documents. This review does not relieve the supplier of responsibility for errors, omissions or any deviation from the requirements of the contract documents. Mike Harmel 07.20.2015 Pavilion Construction NW, LLC 4700 SW Macadam Ave. Portland, OR 97239 Phone: (503)290-5005 Fax: (503)244-1810 www.pavilionconstruction.com Page 1 of 1
Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 SECTION 10 28 00 TOILET, BATH AND LAUNDRY ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General, Supplementary and/or Special Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Public-use washroom accessories. 2. Public-use shower room accessories. 3. Underlavatory guards. B. Owner-Furnished Contractor Installed (OFCI) Accessories: Refer to FF&E Schedule at the end of Division 02 Section "Selective Demolition." C. Related Sections: 1. Division 06 Section Rough Carpentry for backing, blocking and attachment of accessories to wood framing. 1.3 SUBMITTALS A. Product Data: For each type of product indicated. B. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each accessory required. 1. Identify locations using room designations indicated. 2. Identify products using designations indicated. C. Maintenance data. D. Warranty: Sample of special warranty. 1.4 QUALITY ASSURANCE A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application. BLRB Architects - Portland, Oregon TOILET, BATH AND LAUNDRY ACCESSORIES 10 28 00-1
Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 PART 2 - PRODUCTS 2.1 PUBLIC-USE WASHROOM ACCESSORIES A. Basis-of-Design Products: Subject to compliance with requirements, provide products by Bobrick Washroom Equipment, Inc. 1. Manufacturers providing comparable products that may be incorporated in to the Work include, but are not limited to, the following a. American Specialties, Inc. b. Bobrick Washroom Equipment, Inc. c. Bradley Corporation. B. Grab Bar (GB): 1-1/4-inch diameter, stainless steel with snap flange. 1. Basis-of-Design Product: Bobrick B-5806.99. 2. Mounting: Flanges with concealed fasteners. 3. Material: Stainless steel, 0.05 inch thick. a. Finish: Satin finish with peened gripping surface. 4. Configuration and Length: As indicated on Drawings. 2.2 PUBLIC-USE SHOWER ROOM ACCESSORIES A. Basis-of-Design Products: Subject to compliance with requirements, provide products by Bobrick Washroom Equipment, Inc. 1. Manufacturers providing comparable products that may be incorporated in to the Work include, but are not limited to, the following a. American Specialties, Inc. b. Bobrick Washroom Equipment, Inc. c. Bradley Corporation. B. Grab Bar (GB): 1-1/4-inch diameter, stainless steel with snap flange. 1. Basis-of-Design Product: Bobrick B-5837.99. 2. Mounting: Flanges with concealed fasteners. 3. Material: Stainless steel, 0.05 inch thick. a. Finish: Satin finish with peened gripping surface. 4. Configuration and Length: As indicated on Drawings. C. Folding Shower Seat (FS): 1. Basis-of-Design Product: Bobrick B-5191- Compact design. 2. Configuration: Rectangular seat. 3. Seat: Phenolic or polymeric composite of slat-type or one-piece construction in color as selected by Architect. 4. Mounting Mechanism: Stainless steel, No. 4 finish (satin). 5. Dimensions: 18 wide x 15-13/16 projecting from wall. BLRB Architects - Portland, Oregon TOILET, BATH AND LAUNDRY ACCESSORIES 10 28 00-2
Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 2.3 UNDERLAVATORY GUARDS A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: 1. Plumberex Specialty Products, Inc. 2. IPS Corporation, Truebro B. Underlavatory Guard: 1. Description: Insulating pipe covering for supply and drain piping assemblies that prevent direct contact with and burns from piping; allow service access without removing coverings. 2. Material and Finish: Antimicrobial, molded plastic, white. PART 3 - EXECUTION 3.1 INSTALLATION A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated. B. Grab Bars: Install to withstand a downward load of at least 250 lbf, when tested according to ASTM F 446. END OF SECTION 10 28 00 BLRB Architects - Portland, Oregon TOILET, BATH AND LAUNDRY ACCESSORIES 10 28 00-3