Agilent Sun Power Series HLMP-CB1, HLMP-CM1, HLMP-CB3, HLMP-CM3 T-1 3 / 4 ( mm) Precision Optical Performance InGaN Blue and Green Lamps Data Sheet Description These high intensity blue and green LEDs are based on InGaN material technology. InGaN is the most efficient and cost effective material for LEDs in the blue and green region of the spectrum. The 472 nm typical dominant wavelength for blue and 26 nm typical dominant wavelength for green are well suited to color mixing in full color signs. These LED lamps are untinted, nondiffused, T-1 3 / 4 packages incorporating second generation optics producing well defined spatial radiation patterns at specific viewing cone angles. These lamps are made with an advanced optical grade epoxy, offering superior high temperature and high moisture resistance performance in outdoor signal and sign applications. The high maximum LED junction temperature limit of +13 C enables high temperature operation in bright sunlight conditions. The package epoxy contains both UV-A and UV-B inhibitors to reduce the effects of long term exposure to direct sunlight. These lamps are available in two viewing angle options to give the designer flexibility with optical design. Features Well defined spatial radiation pattern Viewing angles: 1 and 3 High luminous output Colors: 472 nm Blue, 26 nm Green Superior resistance to moisture UV resistant epoxy Benefits Superior performance in outdoor environments Wavelengths suitable for color mixing in full color (RGB) signs Applications Commercial outdoor signs Automotive interior lights Front panel indicators Front panel backlighting CAUTION: HLMP-CBxx and HLMP-CMxx LEDs are Class 1 ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Agilent Application Note AN-1142 for additional details.
LED Indicators Device Selection Guide Typical Color and Dominant Luminous Intensity, Leads with Package Part Number Viewing Angle Wavelength λd (nm) Typ. Iv (mcd) Min. Stand-Offs Drawing HLMP-CB1-Pxx 1 Blue 472 88 No A HLMP-CB1-Rxx 1 Blue 472 1 No A HLMP-CB16-Pxx 1 Blue 472 88 Yes B HLMP-CB3-Kxx 3 Blue 472 31 No A HLMP-CB3-Mxx 3 Blue 472 2 No A HLMP-CB31-Mxx 3 Blue 472 2 Yes B HLMP-CM1-Sxx 1 Green 26 19 No A HLMP-CM1-Wxx 1 Green 26 No A HLMP-CM16-Sxx 1 Green 26 19 Yes B HLMP-CM3-Mxx 3 Green 26 2 No A HLMP-CM3-Sxx 3 Green 26 19 No A HLMP-CM31-Mxx 3 Green 26 2 Yes B Part Numbering System HLMP - X X XX - X X X XX Mechanical Options : Bulk DD: Ammo Pack Color Bin Selection : Full color range Maximum Intensity Bin : No maximum Iv bin limit Minimum Intensity Bin Refer to device selection guide Viewing Angle and Standoff Options 1: 1 degree without standoff 16: 1 degree with standoff 3: 3 degree without standoff 31: 3 degree with standoff Color B: Blue M: Green Package C: T-1 3/4 ( mm) round lamp 2
Package Dimensions. ±.2 (.197 ±.8). ±.2 (.197 ±.8) 8.71 ±.2 (.343 ±.8) 1.14 ±.2 (.4 ±.8) d 8.71 ±.2 (.343 ±.8) 31.6 (1.244) MIN. 2.3 (.93) MAX..7 (.28) MAX. 31.6 1. ±.1 (.9 ±.6) LEAD (1.244) MIN..7 (.28) 1.14 ±.2 (.4 ±.8) LEAD MAX. 1. (.39) MIN.. ±.1 SQ. TYP. (.2 ±.4) 1. (.39) MIN.. ±.1 SQ. TYP. (.2 ±.4) FLAT.8 ±.2 (.228 ±.8) 2.4 ±.38 (.1 ±.1) FLAT.8 ±.2 (.228 ±.8) 2.4 ±.38 (.1 ±.1) HLMP-Cx1 and HLMP-Cx3 HLMP-Cx16 and HLMP-Cx31 Notes: 1. Dimensions in mm. 2. Tolerance ±.1 mm unless otherwise noted. HLMP-Cx16 d = 12.6 ±.2 (.496 ±.1) HLMP-Cx31 d = 12.22 ±. (.481 ±.2) 3
Absolute Maximum Ratings at T A = 2 C Parameter DC Forward Current [1] Peak Pulsed Forward Current Average Forward Current Reverse Voltage (I R = 1 µa) Power Dissipation LED Junction Temperature Operating Temperature Range Storage Temperature Range Soldering Temperature Note: 1. Derate linearly as shown in Figure for temperatures above C. Blue and Green 3 ma 1 ma 3 ma V 12 mw 13 C 4 C to +8 C 4 C to +1 C 26 C for seconds Electrical/Optical Characteristics at T A = 2 C Parameter Symbol Min. Typ. Max. Units Test Conditions Forward Voltage HLMP-CB1x-P V F 3.8 4. V I F = 2 ma HLMP-CB1-R 3. 4. HLMP-CB3x-K 3.8 4. HLMP-CB3x-M 3.8 4. HLMP-CM1x-S 3.8 4. HLMP-CM1-W 3. 4. HLMP-CM3x-M 3.8 4. HLMP-CM3-S 3. 4. Reverse Voltage V R I R = 1 µa Peak Wavelength Peak of Wavelength of Blue (λ d = 472 nm) λ peak 47 nm Spectral Distribution Green (λ d = 26 nm) 24 at I F = 2 ma Spectral Halfwidth Wavelength Width Blue (λ d = 472 nm) λ 1/2 3 nm at Spectral Power Green (λ d = 26 nm) 47 Point at I F = 2 ma Capacitance C 43 pf V F =, F = 1 MHz Luminous Efficacy Emitted Luminous Blue (λ d = 472 nm) η v 7 lm/w Power/Emitted Radiant Green (λ d = 26 nm) 2 Power Thermal Resistance RΘ J-PIN 24 C/W LED Junction-to- Cathode Lead 4
RELATIVE INTENSITY 1..9 BLUE GREEN.8.7.6..4.3.2.1 4 4 6 6 7 2. 2.2 2.4 2.6 2.8 3. 3.2 3.4 3.6 3.8 WAVELENGTH nm FORWARD VOLTAGE FORWARD CURRENT 3 2 2 1 1 I F FORWARD CURRENT ma 3 2 2 1 1 2. 2.2 2.4 2.6 2.8 3. 3.2 3.4 3.6 3.8 4. 4.2 V F FORWARD VOLTAGE V Figure 1. Relative intensity vs. wavelength. Figure 2. Forward current vs. forward voltage (for HLMP-CB1-R, HLMP-CM1-W and HLMP-CM3-S). Figure 3. Forward current vs. forward voltage (for HLMP-CB1x-P, HLMP-CB3-K, HLMP-CB3x-M, HLMP-CM1x-S and HLMP-CM3x-M). INTENSITY NORMALIZED AT 2 ma 1. 1.. 1 1 2 2 3 I F FORWARD CURRENT ma 4 3 3 2 2 1 1 2 4 6 8 1 NORMALIZED INTENSITY 1..9.8.7.6..4.3.2.1-3 -2-1 1 2 3 I F FORWARD CURRENT ma T A AMBIENT TEMPERATURE C ANGULAR DISPLACEMENT DEGREES Figure 4. Relative luminous intensity vs. forward current. Figure. Maximum forward current vs. ambient temperature. Figure 6. Spatial radiation pattern 1 lamps. 1. 478 1.2 NORMALIZED INTENSITY.9.8.7.6..4.3.2.1-4 -3-2 -1 1 2 3 4 DOMINANT WAVELENGTH nm 477 4 476 4 47 3 474 3 GREEN 473 2 472 BLUE 2 471 2 4 6 8 1 12 NORMALIZED INTENSITY 1..98.96.94.9..88 2 4 6 8 1 ANGULAR DISPLACEMENT DEGREES FORWARD CURRENT ma DEGREES C Figure 7. Spatial radiation pattern 3 lamps. Figure 8. Color vs. forward current. Figure 9. Normalized Iv vs. T (green).
Color Bin Limits (nm at 2 ma) Blue Color Range (nm) Bin ID Min. Max. 1 46. 464. 2 464. 468. 3 468. 472. 4 472. 476. 476. 48. Tolerance for each bin limit is ±. nm. Green Color Range (nm) Bin ID Min. Max. 1 2. 24. 2 24. 28. 3 28. 32. 4 32. 36. 36. 4. Intensity Bin Limits Bin Name Min. Max. K 31 4 L 4 2 M 2 68 N 68 88 P 88 11 Q 11 1 R 1 19 S 19 2 T 2 32 U 32 42 V 42 W 72 Tolerance of each minimum and maximum is ± 1%. Tolerance for each bin limit is ±. nm. Note: 1. All bin categories are established for classification of products. Products may not be available in all bin categories. Please contact your Agilent representatives for further information. 6
www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (8) 23-312 or (48) 64-867 Europe: +49 () 6441 9246 China: 18 6 17 Hong Kong: (+6) 6271 241 India, Australia, New Zealand: (+6) 6271 2394 Japan: (+81 3) 333-812(Domestic/International), or 12-61-128(Domestic Only) Korea: (+6) 6271 2194 Malaysia, Singapore: (+6) 6271 24 Taiwan: (+6) 6271 264 Data subject to change. Copyright 23 Agilent Technologies, Inc. Obsoletes 988-739EN January 16, 23 988-868EN