F 110 M M SELV Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function High efficiency up to 94% Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer IP67 / IP65 design for indoor or outdoor installations Type HL LED Driver for use in Class Ⅰ, Division 2 hazardous location luminaires Three in one dimming function (1~10Vdc or PWM signal or resistance) Suitable for LED lighting and street lighting applications Compliance to worldwide safety regulations for lighting Suitable for dry / damp / wet locations 5 years warranty (Note.10) IP65 IP67 H L G -150H s er i es - A Blank : IP67 rated. Cable for I/O connection. A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance. D (option, safety pending) : IP67 rated. Timer dimming function, contact MEAN WELL for details. SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT OTHERS NOTE DC VOLTAGE Can be adjusted by internal potentiometer A type only CURRENT ADJ. RANGE 7.5 ~.5A 6 ~ 10A 4.5 ~ 7.5A 3.8 ~ 6.3A 3 ~ 5A 2.5 ~ 4.2A 2.16 ~ 3.6A 1.92 ~ 3.2A 1.68 ~ 2.8A VOLTAGE TOLERANCE Note.3 ±2.5% ±2.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION EMC IMMUNITY MTBF - -15 - -24-30 -36-42 -48 V 15V V 24V 30V 36V 42V 48V CONSTANT CURRENT REGION Note.4 6 ~V 7.5 ~ 15V 10 ~ V ~ 24V 15 ~ 30V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V RATED CURRENT RATED POWER.5A 10A 7.5A 6.3A 5A 4.2A 3.6A 3.2A 153.6W 2.8A RIPPLE & NOISE (max.) Note.2 150mVp-p 150mVp-p 150mVp-p 150mVp-p 0mVp-p 0mVp-p 0mVp-p 0mVp-p 0mVp-p VOLTAGE ADJ. RANGE Note.6 10.8 ~ 13.5V 13.5 ~ 17V 17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 38 ~ 46V 43 ~ 53V 49 ~ 58V TOTAL HARMONIC DISTORTION SHORT CIRCUIT ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±2.0% ±1.5% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% Note.8 1000ms,50ms/115VAC 500ms,50ms/230VAC at full load ; B type 1000ms,0ms/115VAC 500ms,0ms/230VAC at 95% load 16ms at full load 230VAC / 115VAC Note.5 90 ~ 305VAC 7 ~ 431VDC 47 ~ 63Hz PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) THD< % when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input 91.5% 92% 93% 93% 93.5% 93.5% 94% 94% 94% 1.7A / 115VAC 0.75A / 230VAC 0.7A / 277VAC COLD START 65A(t width=425 μs measured at 50% I peak) at 230VAC <0.75mA / 277VAC 95 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V 54 ~ 63V 59 ~ 65V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery Shut down o/p voltage, recovers automatically after temperature goes down -40 ~ +70 (Refer to "Derating Curve") ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.7 UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1, J61347-2-13 approved ; design refer to UL60950-1, TUV EN60950-1 SAFETY & WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC EMISSION Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A 192.2K hrs min. MIL-HDBK-217F (25 ) -54 DIMENSION *68*38.8mm PACKING 1.15Kg; pcs/14.8kg/0.8cuft 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at MHz of bandwidth by using a " twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to "DRIVING METHODS OF LED MODULE". 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. A type only. 7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. 8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 10. Refer to warranty statement. 11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. 54V ±0.5% ±0.5%
Mechanical Specification Case No.954D Unit:mm Blank:() 4 ψ 4.2 IP67 rated. Cable for I/O connection. A Type:(-_A) 4 Vo A DJ. Io A DJ. ψ4.2 IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) B Type:(-_B) 4 ψ 4.2 DIM+(Blue ) DIM-(W hi te ) File Name:-SPEC 14-05-30
D Type(option):(-_D) 4 ψ 4.2 IP67 rated. Timer dimming function, contact MEAN WELL for details. Block Diagram Fosc : 100KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V DIM+ DIM- (B Type) Derating Curve Static Characteristics 100 80 60 40 100 90 80 70 60 50 40-40 -25-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 5 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz File Name:-SPEC 14-05-30
Power Factor Characteristic 1.0 0 0.9 8 0.9 6 0.9 4 0.9 2 0.9 0 0.8 8 0.8 6 0.8 4 0.8 2 0.8 0 0.7 8 Constant Current Mode 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % LOAD () 2 7 7 V a c 2 3 0 V a c 1 1 5 V a c EFFICIENCY vs LOAD (48V Model) series possess superior working efficiency that up to 94% can be reached in field applications. 94 90 86 82 78 277Vac 230Vac 115Vac 74 70 10% % 30% 40% 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B). 100 (A) Constant Voltage area (B) Constant Current region In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io (%) Typical LED power supply I-V curve File Name:-SPEC 14-05-30
DIMMING OPERATION (for B-type only) DIM+(Blue ) DIM-(W hi te ) Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connect ing a resistance or 1 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Single driver 10KΩ KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ OPEN Resistance value Multiple drivers (N =drive r qua ntity for syn ch ro nize d 10K Ω/N K Ω/N 30K Ω/N 40K Ω/N 50K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N ----- dim ming operation ) Percentage of rated current 10% % 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% 1 ~ 10V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz Duty value Percentage of rated current Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. Dimming connection diagram for turning the lighting fixture ON/OFF : N FG L 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 10% % 30% 40% 50% 60% 70% 80% 10% 10% % % 30% 30% 40% 40% 50% 50% 60% 60% 70% 70% 80% 80% 90% 100% 90% 90% 100% 100% OPEN 95%~108% OPEN 95%~108% Relay Switch Adjuster 10K~100K Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N B Type DIM+ DIM- V(-) V(+) Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. 1.Output constant current level can be adjusted through output cable by connecting a resistance or 1~10Vdc or 10V PWM signal between DIM+ and DIM-. 2.The LED lighting fixture can be turned ON/OFF by the switch. File Name:-SPEC 14-05-30
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of to operate in dry/wet/damp or outdoor environment. AC source I/P O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M Order No. Sui tabl e Cur ren t 4- PIN 5 A/PIN M - 04 10A max. 5- PIN 5 A/PIN M - 05 10A max. M15 Order No. Suitable Cur ren t 2- PIN A/PIN M 15-02 A max. LED Lamp Cable Joiner 66 26 CJ04-1 suitable for 14AWG~16AWG CJ04-2 suitable for 18AWG~22AWG Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ04-1, CJ04-2. Junction Box(Option ) 4 366 76 10 5 -V(Black) SJT W 14AWG 2-ψ5 3- PF 1/2" 150± 3- PF 1/2" 150± Optional junction box available for A / Blank - type, please contact MEAW WELL for details. 86 File Name:-SPEC 14-05-30