Page 1 of 24 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT FOR FCC CLASS A VERIFICATION Test Report No. AGR No. Applicant Address Manufacturer Address Type of Equipment Model Name Serial number Total page of Report : E06DR-065 : A06NA-116 : Win4NET Co., Ltd. : KOLON Digital Tower 1301, 222-7, Kuro-Dong, Kuro-Gu, Seoul, 152-848, Korea : Win4NET Co., Ltd. : KOLON Digital Tower 1301, 222-7, Kuro-Dong, Kuro-Gu, Seoul, 152-848, Korea : DVR(Digital Video Recorder) : XM-5016 : N/A : 24 pages (including this page) Date of Incoming : December 04, 2006 Date of Issuing : December 19, 2006 SUMMARY The equipment complies with the regulation; FCC Part 15 Subpart B, Class A (Verification). This test report contains only the results of a single test of the sample supplied for the examination. It is not a general valid assessment of the features of the respective products of the mass-production. Prepared by: Approved by: Seung-Hyun, Nam / Project Engineer Gea-Won, Lee / Chief Engineer EMC Dept. EMC Dept. ONETECH Corp. ONETECH Corp.
Page 2 of 24 CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE...3 2. GENERAL INFORMATION...4 2.1 PRODUCT DESCRIPTION...4 2.2 MODEL DIFFERENCES:...4 2.3 RELATED SUBMITTAL(S) / GRANT(S)...4 2.4 TEST SYSTEM DETAILS...4 2.5 TEST METHODOLOGY...4 2.6 TEST FACILITY...4 3. SYSTEM TEST CONFIGURATION...5 3.1 JUSTIFICATION...5 3.2 CONDITION DURING THE TEST...5 3.3 CABLE DESCRIPTION...5 3.4 EQUIPMENT MODIFICATIONS...6 3.5 CONFIGURATION OF TEST SYSTEM...6 4. PRELIMINARY TEST...6 4.1 AC POWER LINE CONDUCTED EMISSION TEST...6 4.2 RADIATED EMISSION TEST...6 5. FINAL RESULT OF MEASURMENT...7 5.1 CONDUCTED EMISSION TEST...7 5.2 RADIATED EMISSION TEST...8 6. FIELD STRENGTH CALCULATION...9 7. LIST OF TEST EQUIPMENT...10 APPENDIX I - CONDUCTED EMISSION GRAPH TEST DATA...11 APPENDIX II - TEST SET-UP PHOTOS (CONDUCTED EMISSION)...12 APPENDIX III - TEST SET-UP PHOTOS (RADIATED EMISSION)...13 APPENDIX IV - IDENTIFICATION LABEL...14 APPENDIX V - PHOTOGRAPHS REPORT...15 APPENDIX VI INFORMATION TO THE USER IN USER S MANUAL...24
Page 3 of 24 1. VERIFICATION OF COMPLIANCE APPLICANT ADDRESS CONTACT PERSON : Win4NET Co., Ltd. : KOLON Digital Tower 1301, 222-7, Kuro-Dong, Kuro-Gu, Seoul, 152-848, Korea : Mr. Sung-Dae, Kim / Research Engineer TELEPHONE NO : +82-2-2103-5600 MODEL NAME SERIAL NUMBER : XM-5016 : N/A DATE : December 19, 2006 DEVICE TYPE E.U.T. DESCRIPTION THIS REPORT CONCERNS CLASS A DIGITAL DEVICE - UNINTENTIONAL RADIATOR DVR(Digital Video Recorder) ORIGINAL GRANT MEASUREMENT PROCEDURES ANSI C63.4: 2003 TYPE OF EQUIPMENT TESTED KIND OF EQUIPMENT AUTHORIZATION REQUESTED EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) MODIFICATIONS ON THE EQUIPMENT TO ACHIEVE COMPLIANCE FINAL TEST WAS CONDUCTED ON PRE-PRODUCTION VERIFICATION FCC PART 15 (CLASS A) No 10 METER OPEN AREA TEST SITE -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements.
Page 4 of 24 2. GENERAL INFORMATION 2.1 Product Description The Win4NET Co., Ltd., Model XM-5016 (referred to as the EUT in this report) is a DVR(Digital Video Recorder). Product specification described herein was obtained from product data sheet or user s manual. CHASSIS TYPE LIST OF EACH OSC. OR CRY. FREQ.(FREQ.>=1MHz) NUMBER OF LAYERS Metal Main Board: 12.288 MHz, 14.318 MHz, 25 MHz, 27 MHz and 48 MHz 2 Layers : BNC Board, Terminal Board, USB Board and Keypad Board 6 Layers : Main Board ELECTRICAL RATING AC 110-240V~, 47-63Hz, 1.7A EXTERNAL CONNECTOR AC Inlet, Main Power Switch, RJ45(LAN), RS232, VGA, Audio In/Out, S-Video, RS485, Alarm In/Out, USB, Video In/Out 2.2 Model Differences: -. The difference(s) compared to the EUT is as follows: None 2.3 Related Submittal(s) / Grant(s) Original submittal only 2.4 Test System Details The model numbers for all the equipments which were used in the tested system is: Model Manufacturer FCC ID Description Connected to XM-5016 Win4NET Co., Ltd. N/A DVR(Digital Video Recorder) (EUT) - PP01L DELL Computer Corp. DoC Notebook PC EUT N/A NewQ N/A LCD Monitor EUT SAM-14M Samsung N/A CCTV Monitor EUT SCC141H SAMBO N/A CCD Camera EUT 2.5 Test Methodology Both conducted and radiated testing was performed according to the procedures in ANSI C63.4: 2003. Radiated testing was performed at a distance of 10 meters from EUT to the antenna. 2.6 Test Facility The open area test site and conducted measurement facilities are located on at 307-51 Daessangryung-Ri, Chowol-Eup, Kwangju-City, Kyounggi-Do, 464-860, Korea. Description details of test facilities were submitted to the Commission on April 04, 2003. (Registration Number: 340658)
Page 5 of 24 3. SYSTEM TEST CONFIGURATION 3.1 Justification This device was configured for testing in a typical way as a normal customer is supposed to be used. During the test, the following components were installed inside of the EUT. DEVICE TYPE MANUFACTURER MODEL/PART NUMBER FCC ID Main Board N/A N/A N/A BNC Board N/A N/A N/A Switch Board N/A W4N-KEYPAD-V1.1 N/A Power Board N/A N/A N/A CD-RW LITE-ON IT CORP. SOHR-5239V N/A HDD Western Digital WD800JB-00JJCO N/A 3.2 Condition during the test -. After connecting the camera to the DVR (EUT), the captured images were continuously displayed on the screen of the PC and CCTV monitors. Notebook PC was connected to the EUT in order to the ping test via the LAN port from remote location. And other terminals of the EUT are connected to proper peripherals and cables. 3.3 Cable Description Port name Shielded Ferrite Bead Metal Hood Length (m) Connected to AC In N N N 1.5 LISN RJ45 N N BOTH END 1.5 Notebook PC RS232 Y N EUT END 1.5 - VGA Y BOTH END BOTH END 1.5 LCD Monitor Audio In/Out Y N BOTH END 1.5 - S-Video Y N BOTH END 1.5 CCTV Monitor RS485 N N EUT END 1.5 - Alarm In/Out N N EUT END 1.5 - USB Y N BOTH END 1.5 - Video In Y N BOTH END 1.5 CCD Camera Video Out Y N BOTH END 1.5 CCTV Monitor
Page 6 of 24 3.4 Equipment Modifications -. None 3.5 Configuration of Test System Line Conducted Test : The power cord of the EUT was connected to LISN. All supporting equipments were connected to another LISN. Preliminary Power lines Conducted Emission test were performed by using the procedure in ANSI C63.4: 2003 7.2.3 to determine the worse operating conditions. Radiated Emission Test : Preliminary radiated emission test was conducted using the procedure in ANSI C63.4: 2003 8.3.1.1 to determine the worse operating conditions. Final radiated emission test was conducted at 10 meters open area test site. 4. PRELIMINARY TEST 4.1 AC Power line Conducted Emission Test During Preliminary Test, the following operating mode was investigated Operation Mode The captured images were displayed continuously on the screen of the Monitors. The Worse operating condition (Please check one only) X 4.2 Radiated Emission Test During Preliminary Test, the following operating mode was investigated Operation Mode The captured images were displayed continuously on the screen of the Monitors. The Worse operating condition (Please check one only) X
Page 7 of 24 5. FINAL RESULT OF MEASURMENT Preliminary test was done in normal operation mode. And the final measurement was selected for the maximized emission level. 5.1 Conducted Emission Test Humidity Level : 45 % Temperature : 22 C Limits apply to Type of Test Result : FCC CFR 47, PART 15, SUBPART B, SECTION 15.107(b) : CLASS A : PASSED BY 12.21 db at 9.50 MHz under peak mode EUT : DVR(Digital Video Recorder) Date: December 06, 2006 Operating Condition Detector : The captured images were displayed continuously on the screen of the Monitors. : CISPR Quasi-Peak (6 db Bandwidth: 9 khz) Frequency Line Peak (dbuv) Margin (MHz) Emission level Q.P Limits (db) 1.33 H 56.74 73.00-16.26 1.38 N 54.81 73.00-18.19 5.10 H 56.15 73.00-16.85 6.17 N 55.14 73.00-17.86 9.50 N 60.79 73.00-12.21 9.77 H 58.52 73.00-14.48 Frequency Line Average (dbuv) Margin (MHz) Emission level Limits (db) 1.33 H 39.42 60.00-20.58 5.10 H 41.06 60.00-18.94 9.50 N 41.50 60.00-18.50 9.77 H 38.27 60.00-21.73 Line Conducted Emissions Tabulated Data Remark : H : Hot Line, N : Neutral line See Appendix I for an overview sweep performed with peak and average detector. Tested by: Dong-Yub, Lee / Test Engineer
Page 8 of 24 5.2 Radiated Emission Test The following table shows the highest levels of radiated emission on both polarizations of horizontal and vertical. Humidity Level : 40 % Temperature : 19 C Limits apply to Type of Test Result : FCC CFR 47, PART 15, SUBPART B, SECTION 15.109(b) : CLASS A : PASSED BY 4.44 db at 636.50 MHz EUT : DVR(Digital Video Recorder) Date: December 04, 2006 Operating Condition Frequency Range Detector Distance : The captured images were displayed continuously on the screen of the Monitors. : 30MHz 1000MHz : CISPR Quasi-Peak (6 db Bandwidth: 120 khz) : 10 Meter Radiated Emission Ant Correction Factors Total FCC CLASS A Freq. Amp. Ant. Cable Amp. Limit Margin (MHz) (dbuv) Pol. (dbuv/m) (db) (dbuv/m) (dbuv/m) (db) 162.10 15.90 H 15.06 2.82 33.78 43.52-9.74 270.00 18.10 H 17.50 3.86 39.46 46.44-6.98 434.00 15.10 H 17.74 4.84 37.68 46.44-8.76 486.00 15.90 H 18.90 5.19 39.99 46.44-6.45 514.00 17.10 V 19.27 5.36 41.73 46.44-4.71 543.00 14.60 V 19.50 5.47 39.57 46.44-6.87 636.50 15.00 H 20.98 6.02 42.00 46.44-4.44 653.10 11.50 H 21.38 6.12 39.00 46.44-7.44 Radiated Emission Tabulated Data Remark: H : Horizontal, V : Vertical Tested by: Dong-Yub, Lee / Test Engineer
Page 9 of 24 6. FIELD STRENGTH CALCULATION Meter readings are compared to the specification limit correcting for antenna and cable losses + Meter reading (dbuv) + Cable Loss (db) + Antenna Factor (Loss) (db/meter) = Corrected Reading (dbuv/meter) - Specification Limit (dbuv/meter) = db Relative to Spec (+/- db)
Page 10 of 24 7. LIST OF TEST EQUIPMENT No. EQUIPMENTS MFR. MODEL SER. NO. LAST CAL DUE CAL USE 1. Test receiver R/S ESVS10 827864/005 DEC/05 12MONTH 2. Test receiver R/S ESHS 10 834467/007 MAY/06 12MONTH 3. Spectrum analyzer HP 8566B 3407A08547 JUN/06 12MONTH R/S FSP 100017 JUN/06 4. TRILOG Broadband Schwarzbeck VULB9163 VULB9163 166 MAY/06 12MONTH Antenna 5. Biconical antenna EMCO 3110 9003-1121 FEB/06 12MONTH Schwarzbeck VHA9103 91031852 FEB/06 6. Log Periodic antenna EMCO 3146 9001-2614 FEB/06 12MONTH Schwarzbeck 9108-A(494) 62281001 FEB/06 7. LISN EMCO 3825/2 9109-1867 JUN/06 12MONTH 9109-1869 JUN/06 Schwarzbeck NSLK 8126 8126-404 JUL/06 8. Position Controller HD GmbH HD100 N/A N/A N/A 9. Turn Table HD GmbH DS420S N/A N/A N/A 10. Antenna Master HD GmbH MA240 N/A N/A N/A 11. RF Amplifier HP 8447D 2727A04987 JUN/06 12MONTH Remark: Mark mean used equipment.
Page 11 of 24 APPENDIX I - Conducted Emission Graph Test Data HOT LINE NEUTRAL LINE
Page 12 of 24 APPENDIX II - TEST SET-UP PHOTOS (Conducted emission)
Page 13 of 24 APPENDIX III - TEST SET-UP PHOTOS (Radiated emission)
Page 14 of 24 APPENDIX IV - IDENTIFICATION LABEL SUGGESTED LABEL FORMAT FOR EQUIPMENT SUBJECT TO VERIFICATION MAY 1995 All devices subject to verification are required to have an identification label pursuant to Section 2.954 of the Rules. Additional labeling requirements may be specified in the particular sections of the FCC rules governing the specific class of equipment. Under NO circumstances shall verified equipment be labeled with a FCC Identifier (FCC ID), or in any manner which implies that such equipment has been approved by the FCC. Model No. 123 Company name or trade name Country of origin * The label showing the equipment identification data may be combined with a label showing other information (serial numbers, other governments requirements, etc.), if desired. Compliance statements, when required, may be shown on the same label or a separate label. See the "Check sheet" for additional information concerning compliance statements. * Country of origin - U.S. Customs and the Federal Trade Commission regulations require all equipment produced in foreign countries to be marked with the country of origin. Questions concerning marking of equipment with the country of origin should be directed to these agencies. PROPOSED FCC LABEL (Part 15 sec. 15.19) The label included following statement will be attached on product or the compliance statement can be observed in a prominent location in the instruction manual. Model name: XM-5016 Win4NET Co., Ltd. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea
Page 15 of 24 APPENDIX V - PHOTOGRAPHS REPORT ATTACHMENT
Page 16 of 24
Page 17 of 24
Page 18 of 24
Page 19 of 24
Page 20 of 24
Page 21 of 24
Page 22 of 24
Page 23 of 24
Page 24 of 24 APPENDIX VI INFORMATION TO THE USER IN USER S MANUAL The instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual. INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WARNING Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment.