TRVseries [TRV-4SE] tube preamplifier [ TRV-4SE Limited] tube preamplifier ( Special version) basic circuit formal: -- NF type Class A amplification phono circuit formal: -- NF type MM cartridge correspondence frequency characteristic: -1 and -3dB( 10Hz - 100kHz) signal to noise ratio:96db output impedance:7kohm Koa -- highly precise -- resistor use input terminal:4 lines ( the one front part and the three rears) one tape-out recording output terminal: -- three lines tubes:--ecc83 amplification stage, rectification stage: -- 5AR4x2 demention -- 340Wx185Hx315Dmm weight: -- 8kg Tube cover Wooden side plates, AC cable [TRV-35SE] EL34 push-pull integrated / power amplifier maximum output: -- 45W+45W (8ohms) output tube: -- EL34 AB class push pull 3 inputs RCA (the one front part and the two rears) one preamplifier input, tape-out recording 1 line Fequency response 10Hz- 100 khz (-1,-4dB) SNlevel 90dB output:impedance 6 / 8ohm Total distortion < 0.1%( 1kHz) Input sencitivity 0.7V Tubes EL34 * 4, 12AU7(ECC82) * 2, 12AX7(ECC83) * 1 head phone terminal Power sanction min 100watts/ max 220watts KOA highly precise resistor use USA quality speaker terminal use outside size:340wx185hx315dmm waight:15kg Tube cover Wooden side plates, AC cable
[TRV-88SE] KT88 push-pull integrated / power amplifier maximum output: -- 45W+45W (8ohms) output tube: -- KT88 AB class push pull 3 inputs RCA (the one front part and the two rears) one preamplifier input, tape-out recording 1 line Fequency response 10Hz- 100 khz (-1,-4dB) SN level 90dB output:impedance 6 / 8ohm Total distortion < 0.1%( 1kHz) Input sencitivity 0.7V head phone terminal Tubes KT8834 * 4, 12AU7(ECC82) * 2, 12AX7(ECC83) * 1 KOA highly precise resistor use Power sanction min 100watts/ max 220watts USA quality speaker terminal use outside size:340wx185hx315dmm waight:15kg Tube cover Wooden side plates, AC cable [TRV-88SER] KT88 push-pull integrated amplifier NEW MODEL This is the newest Integrated Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is a 45 watts per channel using KT88 tubes which create a delicate and holographic sound. The ability to convey a deep, detailed and rich character of the instrument is just phenomenal. Lightning quick in response and the ability to deliver minute details in the recording will easily suck you into the music. The newly designed EI- Orient Core Output transformer creates thundering quick bass, big soundstage and incredible details makes this amplifier one of its kind. Remote control included. Please give us a call and be ready to be amazed. Get yourself ready for a booming year. Remote control: volume, mute Maximum output: 45W+45W Output tube: KT88 ABclass push pull MM phono stage, 3 inputs RCA (the one front part and the two rears) tape-out recording 1 line Fequency response 10Hz- 100 khz (-1,-4dB) SN level 90dB output:impedance 6 / 8ohm Total distortion < 0.1%( 1kHz) Input sencitivity 0.4V head phone terminal Tubes KT88 * 4, 12AU7(ECC82) * 2, 12AX7(ECC83)* 1 Power sanction min 100watts/ max 220watts KOA highly precise resistor use USA quality speaker terminal use outside size:340wx185hx315dmm waight:15kg Remote control,tube cover, Wooden side plates, AC cable
[TRV-A88SE] KT88 single ended integrated amplifier maximum output:--12w+12w(8ohms) fixed bias output tube:-- KT88 A class single-ended output:impedance 6 / 8ohm KOA highly precise resistor use Hi quality capacitor use Frequency response 15Hz- 40 khz ( +1,-1dB) Total distortion < 0.1%(1kHz) SN level 88dB Input sencitivity 0.7V Tubes KT88 * 2, 12AX7(ECC83) * 2 Output inpedance 6-8 ohm Input terminals 3 ( LINE 1 / 2 / 3) Power sanction 60watts demention:230wx185hx400dmm weight:11.5kg Tube cover Wooden side plates, AC cable [TRV-A300SE] 300B single ended integrated amplifier maximum output: -- 8W+8W (8ohms) self bias output tube: -- 300B A class single -ended output impedance 6 / 8ohm KOA highly precise resistor use Hi quality capacitor use Frequency response 10Hz- 50 khz ( +1,-1dB) Total distortion < 0.3%(1kHz) SN level 85dB Input sencitivity 0.6V Tubes 300B * 2, 6SN7 * 2 Output inpedance 6-8 ohm Input terminals 3 Power sanction 80watts demention:230wx185hx400dmm weight:11.5kg Tube cover Wooden side plates, AC cable
[TRV-A300SER] 300B single ended integrated amplifier NEW MODEL maximum output: -- 8W+8W (8ohms) self bias output tube: -- 300B A class single -ended output impedance 6 / 8ohm KOA highly precise resistor use Hi quality capacitor use Frequency response 10Hz- 50 khz ( +1,-1dB) Total distortion < 0.3%(1kHz) SN level 87dB Input sencitivity 0.6V Tubes 300B * 2, 12AU7 * 2, 12AX7 * 1, 5AR4 * 1 Input terminals 3 Power sanction 90watts demention: 340W x 195H x 315Dmm weight:16kg Remote dontrol, Tube cover, Wooden side plates, AC cable [TRV-M300SE] 300B parallel single ended mono power amplifier maximum output: -- 20W+20W ( 8ohms) fixed bias output tube: -- 300B A class parrale single -ended output:impedance 6 / 8 / 16ohm KOA highly precise resistor use Hi qualityl capacitor use Frequency response 10Hz- 60 khz (+1,-3dB) Total distortion < 0.3%( 1kHz) SN level 89dB Input sencitivity 0.8V Tubes 300B * 2, 12AX7 * 1,12AU7 * 1 Input terminals, ballance 1,unballance 1 Power sanction 120watts demention:176wx200hx 440Dmm weight:15kg Tube cover, AC cable [
[ TRV-M88SE] KT88 push pull mono power amplifier maximum output: -- 50W+50W ( 8ohms) fixed bias output tube: -- KT88 classab output:impedance 6 / 8 / 16ohm KOA highly precise resistor use Hi quality capacitor use Frequency response 20Hz- 50 khz (+1,-1dB) Total distortion < 0.1%( 1kHz) SN level 90dB Input sencitivity 0.7V Tubes KT88 * 2, 12AX7 * 1,12AU7 * 1 Input terminals, ballance 1,unballance 1 Power sanction 120watts demention:176wx200hx 440Dmm weight:15kg Tube cover, AC cable [TRV-CD4SE] 24bit192kHz up sampling CD player Total distortion: 0.002% SN level: 100dB Frequency Response: 20-20kHz(± 0.2dB) Channel separation: 92dB Dinamic range: 120dB DA conveter: Barbrown PCM1792 Tubes: 6DJ8(6922)*1 CD drive unit: Sony Dgital output: Rca and Tos Power requirements: 20W Dimension: 340*330*100mm( W/D/H) Analogue output terminals, RCA*1, Ballance*1 Digital output terminals: RCA, TOS Power sanction 20watts Demention:340Wx100Hx 330Dmm weight:20kg Remote control, AC cable
[TRV-EQ3SE] Phono Pre-Ampifier with MC NF type MM MC Phono Stage Frequency response:10hz - 70kHz(-1dB) Total distortion: 0.1% Input level MM 2.5mV, MC Low 0.23mV, MC High 0.19mV Input Impedance MM 47kohm MC 40ohm S/N ratio in Input MM90dB, MC87dB Gain MM 42.5dB, MC Low 58.7, MC High 64.4dB Output Voltage 200mV (1,000 Hz) Maximum Input Capability 250mV( 1kHz) 11mV( 1kHz) RIAA Curve Deviation +/-0.25 db ( 20 to 20,000Hz) Channel Separation More than 90dB Low Cut Filter: 15Hz 18dBoct., Input terminal: 3 lines (MM/ MC1/ MC2) Output terminal: 2 lines (RCA/ XLR) Capacitors : Mundorf Capacitor Resistors: Kiwame Resistors Tubes:ECC803 x 4 (JJ electronics/slovakia) 5AR4 x 1( JJ electronics/slovakia) Power Consumption 15W Dimention W 340mm x D 315mm x H 185mm Weight 10.0 kg Analog disc playing has deeply improved on the present popular digital audio sources, and now along combined is an individual phono amp seeking more of a sound quality.therefore the functions sought in the previous phono amp is consolidated to the signal source selection and volume adjustment. [Low noise design] In the rectification circuit of the amplifier, rectification tubes without switching noise in principle and luxurious rectification circuit with choke transformer are used. [Simple signal transfer] The amplifier minimizes the functions only needed for this amplifier, and the pureness of signals is secured by not passing through any unnecessary points. [Special Features of MC transformer] High stepup efficiency with low loss, reducing a half of transmission loss / Super-perm-alloy gigantic EI core winded / low-loss big copper wire / High linearity in low range / Energetic sound in all ranges supported by carefully-selected materials / Good rise characteristics minimize a phase distortion in audible bandwidgh and clarify / the great sound image / Energetic, lively music reproduction / The winding structure, uniquely devided into layers, for wide bandwidth response and high rise time / Vibration and co-vibration-free body structure by the weighted iron chasis Reproduce realistic music with good S/N images
[TR-MC1SE] MC step-up transformer Frequency response:10hz - 70kHz(-1dB) Input Impedance MC 2-47ohm Gain MC Low 16dB, MC High 22dB Input terminal: 2 lines (MC1/ MC2) Dimention W 180mm x D 155mm x H 145mm Weight 2.5 kg [Special Features of MC transformer] High stepup efficiency with low loss, reducing a half of transmission loss / Super-perm-alloy gigantic EI core winded / low-loss big copper wire / High linearity in low range / Energetic sound in all ranges supported by carefully-selected materials / Good rise characteristics minimize a phase distortion in audible bandwidgh and clarify / the great sound image / Energetic, lively music reproduction / The winding structure, uniquely devided into layers, for wide bandwidth responseand high rise time / Vibration and co-vibration-free body structure by the weighted iron chasis / Reproduce realistic music with good S/N images
[TRV-845SE] 845 single ended integrated amplifier with remote control maximum output: -- 20W+20W ( 8ohms) fixed bias output tube: -- 845 class-a single -ended output:impedance 4 / 8 / 16ohm KOA highly precise resistor use Alps high quality volume Frequency response 10Hz- 50 khz (0,-1dB) Total distortion < 0.1%( 1kHz) SN level 89dB Input sencitivity 0.9V Tubes 300B * 2, 2A3 * 2,6SN7 * 2 Input terminals,,rca 4, XLR 1, PRE-IN 1 Remote control : Volume, Input Selector, Muting Power sanction 300watts demention:460wx260hx 450Dmm weight:38kg Remote unit, tube cage, power cable, spare fises * TRV-845SE is a Pure Class-A Pre-main amplifier fully consists of triode tubes. * By using 2A3 tubes to drive 845, a sharp and delicate sound of 845 is further improved. * A newly developed large EI Orient-core output transformer creates a profound middle and bass sound. * We arranged a remote control for TR-845SE for the first time. * TRV-845SE is equipped with Pre-In facility to use the unit as a Power Amplifier as well.
TRXseries [TRX-1] tube preamplifier with remote control TRX-1 is the newest Pre-Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is using 274B rectifier tube that creates deeper bass with a very delicate and holographic sound. The combination of TRX-P6L, TRX-1 Pre-Amp and TRV-DC4SE convey a deep, detailed and rich character of the instrument is phenomenal. Lightning quick in response and the ability to deliver details in the recording will easily suck you into the music. The newly designed humungous EI-Orient Core Output transformer creates thundering quick bass, big soundstage and incredible details makes this amplifier one of its kind. circuit formal: NF type ClassA amplification 4 band Equalizer frequency:150,400,2k,10khz +/-6dB frequency characteristic: -1 and -3dB(10Hz - 100kHz) signal to noise ratio:96db output impedance: 6kohm Koa -- highly precise -- resistor use input terminal: 5 lines output terminal: -- three lines tubes: ECC83 amplification stage, rectification stage: 274B( 5U4G)x1 demention -- 340Wx185Hx315Dmm weight: -- 8kg Tube cover Wooden side plates, AC cable * Resistors are KOA Made in Japan and capacitors are Mundorf made in Germany [TRX-P6L] tube power amplifier Class AB Push Pull Tubes: 6L6GC x 4 12AX7 x 2 12BH7 x 2 Automatic Bias Output power: 6L6GC - UL @ 25 W, Triode @ 12 W KT-88 - UL @ 30 W, Triode @ 15 W EL-34 - UL @ 30 W, Triode @ 15 W Frequency response: 10HZ - 100KHz S/N ratio: 90Db Input Sensitivity: 600 mv Input Impedance: 100 K Ohm Input Gain; 0, - 3, -6dB NFB : 0, 3, 6 db Input terminal: RCA Out Terminal: 4, 6, 8 Ohms Power Consumption no Signal:100W max Dim: W340 x D315 x H187 ( mm) Weight: 15 Kilos * Resistors are KOA Made in Japan and capacitors are Mundorf made in Germany
NEW MODEL [TRX-PM84] tube integrated amplifier with remote control This is the newest Integrated Amplifier designed by Junichi Yamazaki of Triode Corporation-Japan. It is a 15 watts per channel using EL84 tubes. It create a delicate and holographic sound with the ability to convey a deep, detailed and rich character of the instrument. Lightning quick in response and the ability to deliver minute details in the recording will easily suck you into the music. The newly designed EI- Orient Core Output transformer creates thundering quick bass, big soundstage and incredible details makes this amplifier one of its kind. The First Tube Integrated Amplifier with built in USB DAC, USB Memory, Headphone and MM phono stage. It uses the 6BQ5/ EL84 tubes which outputs 15 watts per channel in Push Pull. It has also a Bass and Treble control and remote control. It is basicaly one of its kind with s traditional Triode sound and beauty. DAC: Burr-Brown made PCM 1798, 24 bit 192 KHz PC-USB (Type B ): Accepts :16 / 24 bit, 32 KHz / 44.1 KHz / 48 KHz / 88.2 KHz / 96 KHz USB Memory (Type A ): Accepts MP3 / AAC / WMA 32 KHz / 44.1 KHz / 48 khz Specifications: Circuit type: 6BQ5 (EL84) AB class Push-Pull Rated Output: 15W +15 W (8Ω) SN ratio: 87dB Frequency Response: 15Hz ~ 50 khz ( ± 1dB ) Input sensitivity: Line / 290 mv 100kΩ, MM/10mV 47 KΩ Input: MM phono system x 1, Line in x 2, PC-USB (Type B ) x 1 system, USB memory (Type A ) x1 Output: x1 Speaker system (4 ~ 8Ω), Headphone jack ( vacuum tube circuits ) Vacuum tube: Output tube 6BQ5 x 4, first stage 12AX7 x 1, driver 12AU7 x 2 Power Consumption: 130 W Dimensions: (W) 12 inches x (H) 6.1 inches x (D) 10.3 inches. Weight: 12.2 kg
NEW MODEL [TRX-M845]845 Drive 845 parralel single-ended mono power amplifier Maximum output: -- A class 50W ( 8ohms) Automatic bias Output tube: -- 845 parralel single -ended Tubes: 845 * 3, 6SN7 * 1, 12AU7 *1 (211 * 2) Output impedance 4 / 6 / 8 / 16 ohms Input : RCA * 1 / XLR * 1 (switch #2 #3 ) KOA highly precise resistor use NFB : 0, 1, 3 db switched Hi qualityl capacitor use Frequency response 10Hz- 50 khz (-2 db) Total distortion < 0.1%( 1kHz) SN level 89dB Input sencitivity 0.9V Power sanction 280 watts Demention:580W x300h x 440Dmm Weight: 55kg Tube cover, AC cable, Fuses