Date of Issue: 9/9 Dynabolt Plus is a general purpose all steel medium duty through fixing for masonry and concrete. For fixing to Concrete, solid and hollow brick, masonry, natural stone. Surface Finish Zinc Cobolt alloy plating with chromate conversion coating. Hot dipped galvanised to AS1 9. Features ~Through fixing no marking out and repositioning. ~Fully assembled. ~Variety of head styles ~Unique sleeve design collapses during tightening to provide pulldown onto fixture. ~Integral nut and washer. Applications Timber to concrete, form work, battens, bottom plates. Services ductwork, pipes brackets, cable trays, suspended ceilings. Metalwork signs, hand rails, gates. Light to medium duty loading. Materials Stainless Steel: AISI 31 Details
Date of Issue: 9/9 INSTALLATION 1. Use fixture as a template, drill a hole to the correct diameter and depth. Clean hole thoroughly with brush. 2. Remove debris by way of a vacuum or hand pump, compressed air, etc. Insert anchor tightly against fixture and tighten with spanner. 3. Continue tightening, allowing the sleeve to twist and pull down the fixture firmly onto the base material. Details
Date of Issue: 9/9 INSTALLATION AND PERFORMANCE DETAILS Hole Ø Embedded Fixture Clearance Ø Tight Torque (Nm) Edge Dist.Min. Structural Limits Spacing Dist. Min. Structural Min. Rec. Working Load (kn) See Safety Factors p.11 & MPa MPa MPa Tensile Shear Tensile Shear Tensile Shear 1 1 1 1 42 0 4 0 1 1 1 1 4 4 9 9 1 1 1 4 0 0 1 7 1 0 1 14 1 1 11 17 2 1 2 3 0 0 1 1 0 1 10 1 2 1.2 3.2 2.4.4 2.7.1 3..9 9.0 4..3.9. 11.7 22..3.3... 1. 1. 1. 1.4 3.7 3.0.9 3.3 7. 4..4 11.0..2 1.3 14.3 22..3.3... 1. 1. 1. 1.7 3.7 3.4.9 3...4 9.7 11..3 11. 1.3 9.2 1. 22..3.3... 1. 1. 1. For shear loads acting toward the edge(s) of the concrete, the above edge distances and spacings are not applicable, please consult Ramset Technical Consultant. This table should be read in conjunction with the Ramset Engineers Design Manual. Details
Date of Issue: 9/9 ROUND HEAD ANCHOR DETAILS Nom fixture Nom Hole (Plate) Stainless Steel Hot Dipped Galvanised 7 0 1 3 D0R* DP00R DP007R DP00R DP000R SETLOK SUSPENSION ANCHOR DETAILS Hole Ø Nom Hole C/S (Plate) S/S Hot Dip Gal 2 3 7 41 0 0 D002S D003S CA04 EYEBOLT ANCHOR DETAILS (Max Rec. Load 0kg) 31 D004X HOOKBOLT ANCHOR DETAILS (Max Rec. Load 0kg) 31 D004K POST HEAD DETAILS Round head M DR0 DR0 DR04SS Flathead M RFM04 RFM0 RFM0 DF04SS DF0SS DF0SS Acorn M RAM04 RAM0 RAM0 Tie wire M M REM0 REM0 REM COMPONENT SET DETAILS 1 M M M *Available only as Standard Dynabolt. mm mm mm mm DC00 DC DC10 DC10 Note: Nominal Hole depth = Embedment depth + 1/2 bolt diameter
Date of Issue: 9/9 ANCHOR DETAILS Nominal Fixture Nominal Hole (Plate) Stainless Steel Hot Dipped Galvanised 1 M M M M M M M M M M M M M1 M1 M1 3 7 92 41 7 3 4 9 2 1 1 113 17 27 2 4 1 4 74 3 2 9 23 3 3 3 1 1 D002* DP00 DP000 DP00 DP00 DP00 DP DP DP7 DP DP DP10 DP1 DP DP DP10 DP11 DP11 DP00 DP11 DP10 DP00SS DP000SS DP00SS DP00SS DP00SS DPSS DP7SS DPSS DP10SS DP1SS DPSS DPSS DPGH DPGH DP7GH DPGH DP10GH DP1GH DPGH DPGH DP10GH DP11GH DP11GH DP00GH DP11GH DP10GH HEX HEAD ANCHOR DETAILS 1 M M M M M M M M M M 4 4 0 0 7 1 27 1 2 1 4 37 3 4 0 0 1 DP00H DP004H DP00H DP00H DP4H DPH DP0H DPH DP1H DP17H DPH DP10H DP11H DP004HSS DP00HSS DP4HSS DP0HSS DP0HSS DPHSS DP17HSS FLAT HEAD ANCHOR DETAILS 0 2 7 47 9 0 21 M 7 M M *Available only as Standard Dynabolt. 3 3 D0F* DP000F DP007F DP0F DP000F DP00F DP07F DPF DPF DP000FSS DP007FSS Note: Nominal Hole depth = Embedment depth + 1/2 bolt diameter Details