HEAVY DUTY STEEL CABINET ASSEMBLY INSTRUCTIONS ONE DRAWER BASE CABINET 05-206
Parts List Part No Description Qty Image ONE DRAWER BASE CABINET Part No Description Qty Image SB- Cabinet Body EH-0 Euro Hinge 4 M6-20 Hex Head Bolt 4 Handle s s 0 6 mm Hex Nut 4 AP-20 Door Pulls 2 25 mm inch Fender Washer 4 AP-DW Drawer Pull 50 mm 2 inch Drywall 4 SLD-0 Slide 4 ASH-3024 Adjustable Shelf DW-80 Large Drawer D-205 Door Panels 2 BSH-3024 Bottom Shelf Small Metal Hinge Mount 6 Liner Drawer Liner Large Metal Bottom Shelf 2 Clip Shelf Clip 4 Pad Door Pad 4 Page 2
One Drawer Base Cabinet Hardware 2 Large Metal s 4 M6-20 6 Hinge s 6 mm Nuts 4 Large Washers 4 Wood s 4 Shelf Clips 4 Door Pads 0 Handle s - Aluminum Drawer Pull 4 Hinges - Drawer Liner 2 - Aluminum Door Pulls Page 3
One Drawer Base Cabinet TOOLS REQUIRED Phillips Driver 0 mm Open End Wrench 0 mm Ratchet/Socket Tape Measure BEFORE YOU BEGIN: Thoroughly Clean the Assembly Area Remove Personal Items that Can Scratch the Cabinet Finish - Watches, Belt, Rings, etc. Open Cartons Carefully to Avoid Damaging Cabinet Panels Compare Carton Contents with Parts List Count Use the Shipping Cartons for the Assembly Surface - Do Not Assemble on Concrete If Using a Cordless Drill for Assembly - Dial Drill Torque to a Low Setting STEP - continued on next page Remove All Drawers From Cabinet - Important Note - Sometimes the rubber keepers on the drawer slides will make the drawers feel like they are locked. Place a flat head screwdriver between the side of the drawer and the side panel and Gently Pry. Drawer will pop open. Open Top Drawer to fully extended position. Push down on Right Drawer Slide release levers and push slide bodies towards cabinet. Repeat the procedure on the Left Drawer Slides. If Drawer does not release from slide, reverse the procedure, pulling up on the right lever and pushing down on the left lever. Remove Drawer from slide and cabinet body. Right Drawer Slide Push Down on Release Lever Note Lever Release May Be reversed Page 4
One Drawer Base Cabinet STEP - continued Remove Drawer from Cabinet Body Page 5
One Drawer Base Cabinet STEP 2 Remove Bottom Shelf by unscrewing 2 Large Metal s holding shelf in rear of cabinet. Remove shelf carefully from cabinet body to avoid scratching or scuffing interior panels. STEP 3 Move cabinet into its final position. Fasten cabinet to wall STUDS and/or adjacent cabinets as required. Wall Mount Parts 4 x Drywall s 4 x Fender Washers Parts 2 x Large Metal s x Bottom Shelf BSH-3024 STEP 4 Adjacent Cabinet Mount Parts 4 x M6-20 Hex Head Bolts 4 x 6 mm Hex Nuts Re-set Bottom Shelf in Cabinet. Push Bottom Shelf flush with front of cabinet. Fasten Bottom Panel using 2 Large Metal s. STEP 5 Extend the 2 top Side Panel Slides. Insert the Top Drawer Slides into these extended slides. When top slides are properly inserted, insert Drawer into the lower slides. STEP 6 Adjust 6-way Euro Hinges to align door panels as required. Place Shelf Clips at desired height - Install Adjustable Shelf. x DW-80 Drawer Left - Right Adjusting Up - Down Adjusting Slots NEVER FORCE SLIDES Installing drawers with double slides can be tricky. If you encounter resistance, check alignment and repeat above instructions. Slides are released by pulling the two plastic levers up or down. If slides are forced, ball bearings may be dislodged from the holding race and will result in a damaged slide. If you do dislodge ball bearing, reinsert ball bearing in its proper location and bend bearing race with a flat tipped screwdriver. Slide will function perfectly. 8 x Hinge Metal s 4 x Shelf Clips CLIP x Adj. Shelf ASH-3024 4 x Door Pads In - Out Adjusting Page 6
One Drawer Base Cabinet CARE AND CLEANING ONLY USE A WATER BASED CLEANING SOLUTION TO WIPE DOWN CABINET SURFACES DO NOT USE SOLVENTS AS THEY MAY DAMAGE THE CABINET FINISH OPTIONAL LEGS IMPORTANT NOTE Do not slide cabinet into position with full weight on legs, the shear force may break or damage the leg. Lift cabinet and set into position. Adjustment Range 4.0-6.5 Leg Mount Parts 4 x Metal s WARRANTY INFORMATION WARRANTY: Cabinets are warranted to be free from defects in material and workmanship for 2 months from the date of the original purchase, with proof of purchase by the original purchaser. In the event we deem the product to be defective, Cabinet vendor will be responsible for replacement of the defective part ONLY. No cost for labor or installation will be reimbursed. Damages due to shipping and handling, improper installation, abuses (intentional or accidental) or normal wear and tear are NOT covered by this warranty. There are no other guarantees or warranties, implied or expressed, beyond the terms of this expressed written warranty. ALL PRICES, DESIGNS, MATERIAL AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Page 7
CABINET WALL MOUNTING All cabinet models have be designed and structurally reinforced for Wall Mounting. Cabinets elevated above the floor allow easy cleaning and access underneath. In addition to a more professional look and finish, wall mounting eliminates the dust balls around the legs and the inevitable rusting on the leg leveling threads. We recommend that the rear of the cabinets rest on a back support of either an existing protruding foundation stem wall or on a dimensional 2 x 6 or 2 x 4 fastened to the wall (see below). Approximately 70% of the cabinet load will travel straight down the wall onto the back support and the balance of the load is cantilevered forward. The back support removes most of the load/force on the drywall screws used to fasten cabinets to the wall studs. The back support also makes install much faster and allows for easier alignment when bolting adjacent cabinets together. Page 8