FCC 47 CFR PART 15 SUBPART C ISED CANADA RSS-247 ISSUE 1 CERTIFICATION TEST REPORT FOR TETRA RADIO HANDSET HVIN: SC2024 PMN: SC2024

FCC 47 CFR PART 15 SUBPART C ISED CANADA RSS-247 ISSUE 1 CERTIFICATION TEST REPORT FOR TETRA RADIO HANDSET HVIN: SC2024 PMN: SC2024 REPORT NUMBER: R11228006-E2 ISSUE DATE: 2016-08-31 Prepared for SEPURA PLC 9000 CAMBRIDGE RESEARCH PARK BEACH DRIVE WATERBEACH CAMBRIDGE CB25 9TL United Kingdom Prepared by 12 LABORATORY DR. RESEARCH TRIANGLE PARK, NC 27709 USA TEL: (919) 549-1400 NVLAP Lab code: 200246-0

Revision History Ver. Issue Date Revisions Revised By 1 2016-08-31 Initial Issue Brian Kiewra Page 2 of 121 This report shall not be reproduced except in full, without the written approval of.

TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS...5 2. TEST METHODOLOGY...6 3. FACILITIES AND ACCREDITATION...6 4. CALIBRATION AND UNCERTAINTY...6 4.1. MEASURING INSTRUMENT CALIBRATION...6 4.2. SAMPLE CALCULATION...6 4.3. MEASUREMENT UNCERTAINTY...7 5. EQUIPMENT UNDER TEST...8 5.1. DESCRIPTION OF EUT...8 5.2. MAXIMUM OUTPUT POWER...8 5.3. DESCRIPTION OF AVAILABLE ANTENNAS...8 5.4. SOFTWARE AND FIRMWARE...8 5.5. WORST-CASE CONFIGURATION AND MODE...9 5.6. DESCRIPTION OF TEST SETUP...10 6. TEST AND MEASUREMENT EQUIPMENT...13 7. ANTENNA PORT TEST RESULTS...17 7.1. ON TIME AND DUTY CYCLE...17 7.1.1. ON TIME AND DUTY CYCLE RESULTS...17 7.1.2. DUTY CYCLE PLOTS...18 7.2. BASIC DATA RATE GFSK MODULATION...19 7.2.1. 20 db AND 99% BANDWIDTH...19 7.2.2. HOPPING FREQUENCY SEPARATION...23 7.2.3. NUMBER OF HOPPING CHANNELS...25 7.2.4. AVERAGE TIME OF OCCUPANCY...28 7.2.5. OUTPUT POWER...33 7.2.6. AVERAGE POWER...34 7.2.7. CONDUCTED SPURIOUS EMISSIONS...35 7.3. ENHANCED DATA RATE QPSK MODULATION...40 7.3.1. 20 db AND 99% BANDWIDTH...40 7.3.2. HOPPING FREQUENCY SEPARATION...44 7.3.3. NUMBER OF HOPPING CHANNELS...46 7.3.4. AVERAGE TIME OF OCCUPANCY...49 7.3.5. OUTPUT POWER...53 7.3.6. AVERAGE POWER...54 7.4. ENHANCED DATA RATE 8PSK MODULATION...55 Page 3 of 121 This report shall not be reproduced except in full, without the written approval of.

7.4.1. 20 db AND 99% BANDWIDTH...55 7.4.2. HOPPING FREQUENCY SEPARATION...59 7.4.3. NUMBER OF HOPPING CHANNELS...61 7.4.4. AVERAGE TIME OF OCCUPANCY...64 7.4.5. OUTPUT POWER...68 7.4.6. AVERAGE POWER...69 7.4.7. CONDUCTED SPURIOUS EMISSIONS...70 8. RADIATED TEST RESULTS...75 8.1. LIMITS AND PROCEDURE...75 8.2. TRANSMITTER ABOVE 1 GHz...76 8.2.1. BASIC DATA RATE GFSK MODULATION...76 8.2.2. ENHANCED DATA RATE 8PSK MODULATION...90 8.2.3. WORSE-CASE 18-26GHz... 104 8.3. WORST-CASE BELOW 1 GHz... 106 9. POWER LINE CONDUCTED... 110 10. SETUP PHOTOS... 112 Page 4 of 121 This report shall not be reproduced except in full, without the written approval of.

1. ATTESTATION OF TEST RESULTS COMPANY NAME: EUT DESCRIPTION: HVIN: PMN: SERIAL NUMBER: SEPURA PLC 9000 CAMBRIDGE RESEARCH PARK BEACH DRIVE WATERBEACH CAMBRIDGE CB25 9TL United Kingdom TETRA RADIO HANDSET SC2024 SC2024 Radiated: 1PR0003Z2A5 Conducted: 1PR0003Z2AQ DATE TESTED: 2016-05-09 to 2016-05-11 APPLICABLE STANDARDS STANDARD CFR 47 Part 15 Subpart C ISED CANADA RSS-247 Issue 1 ISED CANADA RSS-GEN Issue 4 TEST RESULTS Pass Pass Pass tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For By: Prepared By: Jeff Moser EMC Program Manager UL Consumer Technology Division Brian Kiewra WISE Engineer UL Consumer Technology Division Page 5 of 121 This report shall not be reproduced except in full, without the written approval of.

2. TEST METHODOLOGY The tests documented in this report were performed in accordance with FCC CFR 47 Part 2, FCC CFR 47 Part 15, ANSI C63.10-2013, RSS-GEN Issue 4, RSS-247 Issue 1. 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 12 Laboratory Dr., Research Triangle Park, NC 27709, USA and 2800 Suite B, Perimeter Park Drive, Morrisville, NC 27560. 12 Laboratory Dr., RTP, NC 27709 Chamber A Chamber C 2800 Suite B Perimeter Park Dr., Morrisville, NC 27560 Chamber NORTH Chamber SOUTH The onsite chambers are covered under ISED Canada company address code 2180C with site numbers 2180C -1 through 2180C-4, respectively. (RTP) is accredited by NVLAP, Laboratory Code 200246-0. The full scope of accreditation can be viewed at http://www.nist.gov/nvlap/. 4. CALIBRATION AND UNCERTAINTY 4.1. MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturer's recommendations, and is traceable to recognized national standards. 4.2. SAMPLE CALCULATION Where relevant, the following sample calculation is provided: Field Strength = Measured Voltage (dbuv) + Antenna Factor (db/m) + Cable Loss Preamp Gain 36.5 dbuv + 18.7 db/m + 0.6 db 26.9 db = 28.9 dbuv/m Page 6 of 121 This report shall not be reproduced except in full, without the written approval of.

4.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the apparatus: PARAMETER UNCERTAINTY Total RF power, conducted +/- 0.45 RF power density, conducted +/- 1.50 Spurious emissions, conducted +/- 2.94 All emissions, radiated up to 26 GHz +/- 5.36 Temperature +/- 0.07 Humidity +/- 2.26 DC and low frequency voltages +/- 1.27 Conducted Emissions (0.150-30MHz) +/- 2.37 Uncertainty figures are valid to a confidence level of 95%. Page 7 of 121 This report shall not be reproduced except in full, without the written approval of.

5. EQUIPMENT UNDER TEST 5.1. DESCRIPTION OF EUT The EUT is a portable communication device (walkie talkie) that can be configured as a standalone device or operate within a charging cradle. The device comes with an optional lapel speaker accessory. The EUT contains 802.11 b/g and Bluetooth radios. The radio module is manufactured by Texas Instruments. 5.2. MAXIMUM OUTPUT POWER The transmitter has a maximum peak conducted output power as follows: Frequency Range (MHz) Mode Output Power (dbm) Output Power (mw) 2402-2480 Basic GFSK 8.16 6.55 2402-2480 DQPSK 5.10 3.24 2402-2480 Enhanced 8PSK 5.58 3.61 5.3. DESCRIPTION OF AVAILABLE ANTENNAS The radio utilizes an inverted-f antenna, with a maximum gain of 2.5 dbi. 5.4. SOFTWARE AND FIRMWARE The EUT driver software installed during testing was Tetra USB Serial Driver x86. The test utility software used during testing was BT/WiFi Test Script ver 0.5. Page 8 of 121 This report shall not be reproduced except in full, without the written approval of.

5.5. WORST-CASE CONFIGURATION AND MODE Radiated emission and power line conducted emission were performed with the EUT set to transmit at the channel with highest output power as worst-case scenario. The fundamental of the EUT was investigated in three orthogonal orientations X,Y,Z, it was determined that Z orientation was worst-case orientation; therefore, all final radiated testing was performed with the EUT in Z orientation. For charger/cradle mode, the EUT can only be mounted in one orientation (Z-Axis). Based on the conducted measurements, the worst-case data rates were: 802.11b mode: 11 Mbps 802.11g mode: 54 Mbps EUT was tested in standalone mode and mounted in the charger. The EUT was also tested with the lapel speaker accessory attached. For Enhanced Data rate modes, 8DPSK is considered worst-case and only select tests were performed for the DQPSK mode. Additionally, unless noted in the test report, all tests were performed with the DH5 packet size as this was considered worst-case. Page 9 of 121 This report shall not be reproduced except in full, without the written approval of.

5.6. DESCRIPTION OF TEST SETUP SUPPORT EQUIPMENT Support Equipment List Description Manufacturer Model Serial Number FCC ID Laptop Compaq CQ56-115DX CNF1134NRP NA Laptop Lenovo T450 RTP0116PC0A2UQU NA AC Adaptor Click CPS024100240 1541B NA Charging Cradle Sepura STP8000 7PP311551F7005Q NA I/O CABLES (CONDUCTED SETUP) Cable No Port # of Identical ports I/O Cable List Connector Type Cable Length (m) Remarks 1 Antenna Port 1 EUT 0.1m NA CABLES (Radiated Setup) Cable No Port # of Identical ports I/O Cable List Connector Type Cable Length (m) Remarks 1 AC Charger 1 AC Adaptor 1.85 NA 2 Accessory Lapel Speaker 1 RF/Serial >1m NA TEST SETUP Test software exercised the radio card. Page 10 of 121 This report shall not be reproduced except in full, without the written approval of.

SETUP DIAGRAM FOR TESTS Conducted Setup Note The antenna seen in this drawing is the CB radio antenna. Page 11 of 121 This report shall not be reproduced except in full, without the written approval of.

Radiated Setup Standalone Setup Charger Setup Page 12 of 121 This report shall not be reproduced except in full, without the written approval of.

6. TEST AND MEASUREMENT EQUIPMENT The following test and measurement equipment was utilized for the tests documented in this report: Test Equipment Used - Radiated Disturbance Emissions Test Equipment (Morrisville - South Chamber) Equip. ID Description Manufacturer Model Number Last Cal. Next Cal. 0.009-30MHz (Loop Ant.) AT0079 Active Loop Antenna ETS-Lindgren 6502 2015-12-08 2016-12-31 AT0074 AT0069 AT0076 30-1000 MHz Hybrid Broadband Antenna 1-18 GHz Double-Ridged Waveguide Horn Antenna, 1 to 18 GHz 18-40 GHz Horn Antenna, 18-26.5GHz Sunol Sciences Corp. JB3 2015-06-10 2016-06-30 ETS Lindgren 3117 2016-03-07 2017-03-31 ARA MWH-1826/B 2015-08-27 2016-08-31 AT0077 Horn Antenna, 26-40GHz ARA MWH-2640/B 2015-08-27 2016-08-31 S-SAC01 S-SAC02 S-SAC03 S-SAC04 Gain-Loss Chains Gain-loss string: 0.009-30MHz Gain-loss string: 30-1000MHz Gain-loss string: 1-18GHz Gain-loss string: 18-40GHz Receiver & Software Various Various 2015-10-07 2016-10-31 Various Various 2015-06-09 2016-06-30 Various Various 2015-08-22 2016-08-31 Various Various 2016-02-29 2017-02-28 SA0025 Spectrum Analyzer Agilent N9030A 2016-03-17 2017-03-31 SA0026 (18-40GHz RSE) Spectrum Analyzer Agilent N9030A 2016-02-24 2017-02-28 SOFTEMI EMI Software UL Version 9.5 NA NA HI0050 Temp/Humid/Pressure Meter Cole-Parmer 99760-00 2015-07-01 2016-07-31 Page 13 of 121 This report shall not be reproduced except in full, without the written approval of.

Test Equipment Used - Wireless Conducted Measurement Equipment Equipment ID Description Manufacturer Model Number Last Cal. Next Cal. Conducted Room 1 SA0019 Spectrum Analyzer Agilent Technologies E4446A 2015-09-02 2016-09-30 PWM004 RF Power Meter Keysight Technologies N1911A 2015-06-08 2017-06-08 PWS004 Peak and Avg Power Keysight Sensor, 50MHz to 6GHz Technologies E9323A 2015-06-05 2016-06-05 HI0079 Temp/Humid/Pressure Meter Springfield PreciseTemp 2015-07-1 2016-07-31 MM0167 True RMS Multimeter Agilent U1232A 2015-08-17 2016-08-31 76022 T1023 T146 HI0080 DC Regulated Power Supply EMPower USB RF Power Sensor, 10MHz to 6GHz Conducted Room 2 Spectrum Analyzer Temp/Humid/Pressure Meter CircuitSpecialist s.com CSI3005X5 N/A N/A ETS Lindgren 7002-006 2015-10-01 2016-10-01 Agilent Technologies E4446A 2015-06-17 2016-06-17 Springfield HI0080 2015-07-01 2016-07-31 MM0168 True RMS Multimeter Agilent U1232A 2015-08-17 2016-08-31 76021 DC Regulated Power Supply CircuitSpecialist s.com CSI3005X5 N/A N/A Page 14 of 121 This report shall not be reproduced except in full, without the written approval of.

Test Equipment Used - Line-Conducted Emissions Voltage (Morrisville Conducted 1) Equipment Description ID Manufacturer Model Number Last Cal. Next Cal. CBL077 Coax cable, RG223, N-male to BNC-male, 20-ft. Pasternack PE3476-240 2015-10-29 2016-10-31 HI0079 Temp/Humid/Pressure Meter Springfield Precision PreciseTemp 2015-07-01 2016-07-31 LISN003 LISN, 50-ohm/50-uH, 2- Fischer Custom FCC-LISN-50-25-2- conductor, 25A Com. 01-550V 2015-08-24 2016-08-31 LISN008 LISN, 50-ohm/50-uH, 2- Solar conductor, 25A (For support Electronics gear only.) 8012-50-R-24-BNC 2015-09-03 2016-09-30 MM0167 Multi-meter Agilent U1232A 2015-08-17 2016-08-31 PRE0101521 EMI Test Receiver 9kHz-7GHz (75141) Rohde & Schwarz ESCI 7 2015-08-26 2016-08-31 TL001 Transient Limiter, 0.009-30MHz Com-Power LIT-930A 2015-05-22 2016-05-31 PS214 AC Power Source Elgar PS215 AC Power Source Elgar CW2501M (s/n 1523A02396) CW2501M (s/n 1523A02397) SOFTEMI EMI Software UL Version 9.5 NA NA NA NA NA NA Page 15 of 121 This report shall not be reproduced except in full, without the written approval of.

7. MEASUREMENT METHODS Duty Cycle: KDB 558074 Section 6.0 (b) 20 db BW: ANSI C63.10 Section 6.9.2. 99% Occupied Bandwidth: ANSI C63.10-2013, Section 6.9.3 Hopping Frequency Separation: ANSI C63.10 Section 7.8.2 Number of Hopping Channels: ANSI C63.10 Section 7.8.3 Average Time of Occupancy: ANSI C63.10 Section 7.8.4 Output Power: ANSI C63.10 Section 7.8.5 Out-of-band emissions in non-restricted bands: ANSI C63.10 Section 7.8.6 & 7.8.8 Out-of-band emissions in restricted bands: ANSI C63.10:2013 Sections 6.3-6.6 Line Conducted Emissions: ANSI C63.10:2013 Sections 6.2 Page 16 of 121 This report shall not be reproduced except in full, without the written approval of.

8. ANTENNA PORT TEST RESULTS LIMITS 8.1. ON TIME AND DUTY CYCLE None; for reporting purposes only. PROCEDURE KDB 558074 Section 6.0 (b) Test Information Date: 2016-05-10 Tester: Mark Learner 8.1.1. ON TIME AND DUTY CYCLE RESULTS Mode ON Time Period Duty Cycle Duty Duty Cycle 1/B B x Cycle Correction Factor Minimum VBW (msec) (msec) (linear) (%) (khz) 2.4 GHz band (Hopping OFF) Bluetooth GFSK 2.910 3.753 0.775 77.54% 1.10 0.344 Bluetooth 8PSK 2.910 3.753 0.775 77.54% 1.10 0.344 Page 17 of 121 This report shall not be reproduced except in full, without the written approval of.

HOPPING OFF 8.1.2. DUTY CYCLE PLOTS DUTY CYCLE GFSK MODE DUTY CYCLE 8PSK MODE Page 18 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2. BASIC DATA RATE GFSK MODULATION 8.2.1. 20 db AND 99% BANDWIDTH FCC 15.247 (a) (1) IC RSS-247 5.1 (1) IC RSS-Gen clause 6.6 None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 1-5% of the 20 db bandwidth and 99% Occupied Bandwidth. The VBW is set to RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Channel Frequency 20 db Bandwidth 99% Bandwidth (MHz) (khz) (khz) Low 2402 926 855.9652 Middle 2441 938 866.322 High 2480 844 878.7051 Page 19 of 121 This report shall not be reproduced except in full, without the written approval of.

20 db AND 99% BANDWIDTH 20 db BANDWIDTH LOW CH 99% BANDWIDTH LOW CH Page 20 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH MID CH 99% BANDWIDTH MID CH Page 21 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH HIGH CH 99% BANDWIDTH HIGH CH Page 22 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2.2. HOPPING FREQUENCY SEPARATION ANSI C63.10 Section 7.8.2 FCC 15.247 (a) (1) IC RSS-247 5.1 (2) Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 khz or the 20 db bandwidth of the hoping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 khz or two-thirds of the 20 db bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mw. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 300 khz and the VBW is set to 3x RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Channel 1 (MHz) Channel 2 (MHz) Channel Separation (MHz) 2/3 of 20dB BW (MHz) Margin (MHz) 2441 2442 1 0.625-0.375 Page 23 of 121 This report shall not be reproduced except in full, without the written approval of.

HOPPING FREQUENCY SEPARATION HOPPING FREQUENCY SEPARATION Page 24 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2.3. NUMBER OF HOPPING CHANNELS ANSI C63.10 Section 7.8.3 FCC 15.247 (a) (1) (iii) IC RSS-210 5.1 (4) Frequency hopping systems in the 2400 2483.5 MHz band shall use at least 15 nonoverlapping channels. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to cover the entire authorized band, in either a single sweep or in multiple contiguous sweeps for visibility of the entire span. Then, smaller spans are set to more clearly identify the channels. The RBW is set to 30% of the channel spacing (approx. 300 khz). The analyzer is set to Max Hold. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Normal Mode: 79 Channels observed. AFH Mode: min of 20 Channels declared. Page 25 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS NUMBER OF HOPPING CHANNELS (100 MHZ SPAN) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, FIRST SEGMENT) Page 26 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, SECOND SEGMENT) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, THIRD SEGMENT) Page 27 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2.4. AVERAGE TIME OF OCCUPANCY ANSI C63.10 Section 7.8.4 FCC 15.247 (a) (1) (iii) IC RSS-247 5.1 (4) The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to 0 Hz, centered on a single, selected hopping channel. The width of a single pulse is measured in a fast scan. The number of pulses is measured in a 3.16 second scan, to enable resolution of each occurrence. The average time of occupancy in the specified 31.6 second period (79 channels * 0.4 s) is equal to 10 * (# of pulses in 3.16 s) * pulse width. For AFH mode, the average time of occupancy in the specified 8 second period (20 channels * 0.4 seconds) is equal to 10 * (# of pulses in 0.8 s) * pulse width. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Page 28 of 121 This report shall not be reproduced except in full, without the written approval of.

DH Packet Pulse Number of Average Time Limit Margin Width Pulses in of Occupancy (msec) 3.16 (sec) (sec) (sec) seconds GFSK Normal Mode DH1 0.4 32 0.128 0.4-0.272 DH3 1.654 17 0.281 0.4-0.119 DH5 2.904 12 0.348 0.4-0.052 DH Packet Pulse Number of Average Time Limit Margin Width Pulses in of Occupancy (msec) 0.8 (sec) (sec) (sec) seconds GFSK AFH Mode DH1 0.4 8 0.032 0.4-0.368 DH3 1.654 4.25 0.070 0.4-0.330 DH5 2.904 3 0.087 0.4-0.313 Page 29 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH - DH1 PULSE WIDTH DH1 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH1 NUMBER OF PULSES DH1 Page 30 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH3 PULSE WIDTH DH3 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH3 NUMBER OF PULSES DH3 Page 31 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH5 PULSE WIDTH DH5 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH5 NUMBER OF PULSES DH5 Page 32 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2.5. OUTPUT POWER ANSI C63.10 Section 7.8.5 15.247 (b) (1) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. RSS-247 Clause 5.4 (2) For frequency hopping systems operating in the band 2400-2483.5 MHz and employing at least 75 hopping channels, the maximum peak conducted output power shall not exceed 1 W; for all other frequency hopping systems in the band, the maximum peak conducted output power shall not exceed 0.125 W. TEST PROCEDURE The transmitter output was connected to a power meter equipped with a power sensor capable of measuring peak power. The cable assembly insertion loss of 10.1dB (including 10 db pad and 0.1dB cable) was entered as an offset in the power meter to allow for direct reading of power. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS The following is peak power: Channel Frequency Output Power Directional Limit Margin (MHz) (dbm) Gain (dbm) (dbi) Low 2402 8.16 2.50 30-21.84 Middle 2441 7.02 2.50 30-22.98 High 2480 6.65 2.50 30-23.35 Page 33 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.2.6. AVERAGE POWER None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS The cable assembly insertion loss of 10.1 db (including 10 db pad and 0.1 db cable) was entered as an offset in the power meter to allow for direct reading of power. The below is an gated average measurement. Channel Frequency Average Power (MHz) (dbm) Low 2402 8.13 Middle 2441 6.98 High 2480 6.62 Page 34 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMITS 8.2.7. CONDUCTED SPURIOUS EMISSIONS ANSI C63.10 Section 7.8.6 and 7.8.8 FCC 15.247 (d) In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)). IC RSS-247 5.5 In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under Section A8.4 (4), the attenuation required shall be 30 db instead of 20 db. Attenuation below the general field strength limits specified in RSS-Gen is not required. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 khz. The video bandwidth is set to 300 khz. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels. The bandedges at 2.4 and 2.4835 GHz are investigated with the transmitter set to the normal hopping mode. Test Information Date: 2016-05-10 Tester: Mark Learner Page 35 of 121 This report shall not be reproduced except in full, without the written approval of.

RESULTS SPURIOUS EMISSIONS, LOW CHANNEL LOW CHANNEL BANDEDGE LOW CHANNEL SPURIOUS Page 36 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS, MID CHANNEL MID CHANNEL REFERENCE MID CHANNEL SPURIOUS Page 37 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS, HIGH CHANNEL HIGH CHANNEL BANDEDGE HIGH CHANNEL SPURIOUS Page 38 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS BANDEDGE EMISSIONS WITH HOPPING ON LOW BANDEDGE WITH HOPPING ON HIGH BANDEDGE WITH HOPPING ON Page 39 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3. ENHANCED DATA RATE QPSK MODULATION 8.3.1. 20 db AND 99% BANDWIDTH FCC 15.247 (a) (1) IC RSS-247 5.1 (1) IC RSS-Gen clause 6.6 None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 1-5% of the 20 db bandwidth and 99% Occupied Bandwidth. The VBW is set to RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner Channel Frequency 20 db Bandwidth 99% Bandwidth (MHz) (khz) (khz) Low 2402 1332 1211.9 Middle 2441 1338 1228.1 High 2480 1326 1212.7 RESULTS Page 40 of 121 This report shall not be reproduced except in full, without the written approval of.

20 db AND 99% BANDWIDTH 20 DB BANDWIDTH LOW CH 99% BANDWIDTH LOW CH Page 41 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH MID CH 99% BANDWIDTH MID CH Page 42 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH HIGH CH 99% BANDWIDTH HIGH CH Page 43 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3.2. HOPPING FREQUENCY SEPARATION ANSI C63.10 Section 7.8.2 FCC 15.247 (a) (1) IC RSS-247 5.1 (2 Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 khz or the 20 db bandwidth of the hoping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 khz or two-thirds of the 20 db bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mw. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 300 khz and the VBW is set to 3x RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Channel 1 (MHz) Channel 2 (MHz) Channel Separation (MHz) 2/3 of 20dB BW (MHz) Margin (MHz) 2441 2442 1 0.892-0.108 Page 44 of 121 This report shall not be reproduced except in full, without the written approval of.

HOPPING FREQUENCY SEPARATION HOPPING FREQUENCY SEPARATION Note The channel hopping separation of 1MHz is less than the 20 db bandwidth (approx. 1.3 MHz). However, the output power is less than 125 mw and the channel separation is greater than 2/3 the 20 db bandwidth (approx. 875 khz). Page 45 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3.3. NUMBER OF HOPPING CHANNELS ANSI C63.10 Section 7.8.3 FCC 15.247 (a) (1) (iii) IC RSS-247 5.1 (4 Frequency hopping systems in the 2400 2483.5 MHz band shall use at least 15 nonoverlapping channels. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to cover the entire authorized band, in either a single sweep or in multiple contiguous sweeps for visibility of the entire span. Then, smaller spans are set to more clearly identify the channels. The RBW is set to 30% of the channel spacing (approx. 300 khz). The analyzer is set to Max Hold. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Normal Mode: 79 Channels observed. AFH Mode: min of 20 Channels declared. Page 46 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS NUMBER OF HOPPING CHANNELS (100 MHZ SPAN) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, FIRST SEGMENT) Page 47 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, SECOND SEGMENT) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, THIRD SEGMENT) Page 48 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3.4. AVERAGE TIME OF OCCUPANCY ANSI C63.10 Section 7.8.4 FCC 15.247 (a) (1) (iii) IC RSS-247 5.1 (4) The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to 0 Hz, centered on a single, selected hopping channel. The width of a single pulse is measured in a fast scan. The number of pulses is measured in a 3.16 second scan, to enable resolution of each occurrence. The average time of occupancy in the specified 31.6 second period (79 channels * 0.4 s) is equal to 10 * (# of pulses in 3.16 s) * pulse width. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS DQPSK Mode DH Packet Pulse Width Number of Pulses in Average Time of Limit Margin (msec) 3.16 (sec) (sec) (sec) seconds DH1 0.407 31 0.126 0.4-0.274 DH3 1.658 18 0.298 0.4-0.102 DH5 2.904 9 0.261 0.4-0.139 Note: for AFH (DQPSK) mode, please refer to the results of AFH (GFSK) mode; the channel selection and hopping rate are the same for both EDR and Basic Rate operation, data for Basic Rate on page 27 demonstrates compliance with channel occupancy when AFH is employed. Page 49 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH - DH1 PULSE WIDTH DH1 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH1 NUMBER OF PULSES DH1 Page 50 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH3 PULSE WIDTH DH3 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH3 NUMBER OF PULSES DH3 Page 51 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH5 PULSE WIDTH DH5 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH5 NUMBER OF PULSES DH5 Page 52 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3.5. OUTPUT POWER ANSI C63.10 Section 7.8.5 15.247 (b) (1) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. RSS-247 Clause 5.4 (2) For frequency hopping systems operating in the band 2400-2483.5 MHz and employing at least 75 hopping channels, the maximum peak conducted output power shall not exceed 1 W; for all other frequency hopping systems in the band, the maximum peak conducted output power shall not exceed 0.125 W. TEST PROCEDURE The transmitter output was connected to a power meter equipped with a power sensor capable of measuring peak power. The cable assembly insertion loss of 10.1 db (including 10 db pad and 0.1dB cable) was entered as an offset in the power meter to allow for direct reading of power. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Note: For DQPSK mode, the channel separation was limited to 2/3 the 20 db bandwidth. Therefore, the output power was limited to 125 mw. The following is peak power: Channel Frequency Output Power Directional Limit Margin (MHz) (dbm) Gain (dbm) (dbi) Low 2402 5.10 2.50 21-15.90 Middle 2441 3.52 2.50 21-17.48 High 2480 2.89 2.50 21-18.11 Page 53 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.3.6. AVERAGE POWER None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS The cable assembly insertion loss of 10.1 db (including 10 db pad and 0.1 db cable) was entered as an offset in the power meter to allow for direct reading of power. Channel Frequency Average Power (MHz) (dbm) Low 2402 2.75 Middle 2441 0.99 High 2480 0.16 Page 54 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4. ENHANCED DATA RATE 8PSK MODULATION 8.4.1. 20 db AND 99% BANDWIDTH FCC 15.247 (a) (1) IC RSS-247 5.1 (1) IC RSS-Gen clause 6.6 None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 1-5% of the 20 db bandwidth and 99% Occupied Bandwidth. The VBW is set to RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Channel Frequency 20 db Bandwidth 99% Bandwidth (MHz) (khz) (khz) Low 2402 1254 1210.5 Middle 2441 1260 1209.5 High 2480 1248 1199.8 Page 55 of 121 This report shall not be reproduced except in full, without the written approval of.

20 db AND 99% BANDWIDTH 20 DB BANDWIDTH LOW CH 99% BANDWIDTH LOW CH Page 56 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH MID CH 99% BANDWIDTH MID CH Page 57 of 121 This report shall not be reproduced except in full, without the written approval of.

20 DB BANDWIDTH HIGH CH 99% BANDWIDTH HIGH CH Page 58 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4.2. HOPPING FREQUENCY SEPARATION ANSI C63.10 Section 7.8.2 FCC 15.247 (a) (1) IC RSS-247 5.1 (2) Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 khz or the 20 db bandwidth of the hoping channel, whichever is greater. Alternatively, frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 khz or two-thirds of the 20 db bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mw. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 300 khz and the VBW is set to 3x RBW. The sweep time is coupled. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Channel 1 (MHz) Channel 2 (MHz) Channel Separation (MHz) 2/3 of 20dB BW (MHz) Margin (MHz) 2441 2442 1 0.84-0.16 Page 59 of 121 This report shall not be reproduced except in full, without the written approval of.

HOPPING FREQUENCY SEPARATION HOPPING FREQUENCY SEPARATION Note The channel hopping separation of 1MHz is less than the 20 db bandwidth (approx. 1.3 MHz). However, the output power is less than 125 mw and the channel separation is greater than 2/3 the 20 db bandwidth (approx. 875 khz). Page 60 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4.3. NUMBER OF HOPPING CHANNELS ANSI C63.10 Section 7.8.3 FCC 15.247 (a) (1) (iii) IC RSS-247 5.1 (4) Frequency hopping systems in the 2400 2483.5 MHz band shall use at least 15 nonoverlapping channels. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to cover the entire authorized band, in either a single sweep or in multiple contiguous sweeps for visibility of the entire span. Then, smaller spans are set to more clearly identify the channels. The RBW is set to 30% of the channel spacing (approx. 300 khz). The analyzer is set to Max Hold. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Normal Mode: 79 Channels observed. AFH Mode: min of 20 Channels declared Page 61 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS NUMBER OF HOPPING CHANNELS (100 MHZ SPAN) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, FIRST SEGMENT) Page 62 of 121 This report shall not be reproduced except in full, without the written approval of.

NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, SECOND SEGMENT) NUMBER OF HOPPING CHANNELS (30 MHZ SPAN, THIRD SEGMENT) Page 63 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4.4. AVERAGE TIME OF OCCUPANCY ANSI C63.10 Section 7.8.4 FCC 15.247 (a) (1) (iii) IC RSS-247 5.1 (4) The average time of occupancy on any channel shall not be greater than 0.4 seconds within a period of 0.4 seconds multiplied by the number of hopping channels employed. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The span is set to 0 Hz, centered on a single, selected hopping channel. The width of a single pulse is measured in a fast scan. The number of pulses is measured in a 3.16 second scan, to enable resolution of each occurrence. The average time of occupancy in the specified 31.6 second period (79 channels * 0.4 s) is equal to 10 * (# of pulses in 3.16 s) * pulse width. Test Information Date: 2016-05-10 and 2016-05-11 Tester: Mark Learner RESULTS 8PSK (EDR) Mode DH Packet Pulse Number of Average Limit Margin Width (msec) Pulses in 3.16 Time of (sec) (sec) (sec) seconds DH1 0.406 31 0.126 0.4-0.274 DH3 1.656 17 0.282 0.4-0.118 DH5 2.9 13 0.377 0.4-0.023 Page 64 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH - DH1 PULSE WIDTH DH1 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH1 NUMBER OF PULSES DH1 Page 65 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH3 PULSE WIDTH DH3 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH3 NUMBER OF PULSES DH3 Page 66 of 121 This report shall not be reproduced except in full, without the written approval of.

PULSE WIDTH DH5 PULSE WIDTH DH5 NUMBER OF PULSES IN 3.16 SECOND OBSERVATION PERIOD DH5 NUMBER OF PULSES DH5 Page 67 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4.5. OUTPUT POWER ANSI C63.10 Section 7.8.5 15.247 (b) (1) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the 5725-5850 MHz band: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. RSS-247 Clause 5.4 (2) For frequency hopping systems operating in the band 2400-2483.5 MHz and employing at least 75 hopping channels, the maximum peak conducted output power shall not exceed 1 W; for all other frequency hopping systems in the band, the maximum peak conducted output power shall not exceed 0.125 W. TEST PROCEDURE The transmitter output was connected to a power meter equipped with a power sensor capable of measuring peak power. The cable assembly insertion loss of 10.1 db (including 10 db pad and 0.1 db cable) was entered as an offset in the power meter to allow for direct reading of power. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS Note: For 8PSK mode, the channel separation was limited to 2/3 the 20 db bandwidth. Therefore, the output power was limited to 125 mw. The following is peak power. Channel Frequency Output Power Directional Limit Margin (MHz) (dbm) Gain (dbm) (dbi) Low 2402 5.58 2.50 21-15.42 Middle 2441 4.07 2.50 21-16.93 High 2480 3.48 2.50 21-17.52 Page 68 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMIT 8.4.6. AVERAGE POWER None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. Test Information Date: 2016-05-10 Tester: Mark Learner RESULTS The cable assembly insertion loss of 10.1dB (including 10 db pad and 0.1 db cable) was entered as an offset in the power meter to allow for direct reading of power. Channel Frequency Average Power (MHz) (dbm) Low 2402 2.75 Middle 2441 1.00 High 2480 0.16 Page 69 of 121 This report shall not be reproduced except in full, without the written approval of.

LIMITS 8.4.7. CONDUCTED SPURIOUS EMISSIONS ANSI C63.10 Section 7.8.6 and 7.8.8 FCC 15.247 (d) In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 db instead of 20 db. Attenuation below the general limits specified in 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)). IC RSS-247 5.5 In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 db below that in the 100 khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under Section A8.4 (4), the attenuation required shall be 30 db instead of 20 db. Attenuation below the general field strength limits specified in RSS-Gen is not required. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 khz. The video bandwidth is set to 300 khz. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels. The bandedges at 2.4 and 2.4835 GHz are investigated with the transmitter set to the normal hopping mode. Test Information Date: 2016-05-10 Tester: Mark Learner Page 70 of 121 This report shall not be reproduced except in full, without the written approval of.

RESULTS SPURIOUS EMISSIONS, LOW CHANNEL LOW CHANNEL BANDEDGE LOW CHANNEL SPURIOUS Page 71 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS, MID CHANNEL MID CHANNEL BANDEDGE MID CHANNEL SPURIOUS Page 72 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS, HIGH CHANNEL HIGH CHANNEL BANDEDGE HIGH CHANNEL SPURIOUS Page 73 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS BANDEDGE EMISSIONS WITH HOPPING ON LOW BANDEDGE WITH HOPPING ON HIGH BANDEDGE WITH HOPPING ON Page 74 of 121 This report shall not be reproduced except in full, without the written approval of.

9. RADIATED TEST RESULTS LIMITS 9.1. LIMITS AND PROCEDURE FCC 15.205 and 15.209 IC RSS-GEN Clause 8.9 (Transmitter) IC RSS-GEN Clause 7.1.2 (Receiver) Frequency Range Field Strength Limit Field Strength Limit (MHz) (uv/m) at 3 m at 3 m 0.009-0.490 2400/F(kHz) @ 300 m - 0.490-1.705 24000/F(kHz) @ 30 m - 1.705-30 30 @ 30m - 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 TEST PROCEDURE The EUT is placed on a non-conducting table 80 cm above the ground plane for below 1GHz measurements and 1.5 m above the ground plane for above 1GHz measurements. The antenna to EUT distance is 3 meters. For measurements below 1 GHz the resolution bandwidth is set to 120 khz for peak detection measurements or 120 khz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For peak measurements above 1 GHz, the resolution bandwidth is set to 1 MHz and the video bandwidth is set to 3 MHz. For average measurements above 1GHz, the resolution bandwidth and video bandwidth are set as described in ANSI C63.10:2013 for the applicable measurement. The particular averaging method used for this test program was by measuring using a Peak detector with the resolution bandwidth set to 1MHz and a reduced video bandwidth, based on 1/T on where T on is the transmit on time. The spectrum from 9 khz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels in each applicable band. The frequency range of interest is monitored at a fixed antenna height and EUT azimuth. The EUT is rotated through 360 degrees to maximize emissions received. The antenna is scanned from 1 to 4 meters above the ground plane to further maximize the emission. Measurements are made with the antenna polarized in both the vertical and the horizontal positions. Page 75 of 121 This report shall not be reproduced except in full, without the written approval of.

9.2. TRANSMITTER ABOVE 1 GHz 9.2.1. BASIC DATA RATE GFSK MODULATION RESTRICTED BANDEDGE (LOW CHANNEL, STANDALONE) LOW CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 38.64 Pk 32.2-24.2 46.64 - - 74-27.36 124 187 H 2 * 2.377 50.18 Pk 32.1-24.1 58.18 - - 74-15.82 124 187 H 3 * 2.39 28.06 V1TR 32.2-24.2 36.06 54-17.94 - - 124 187 H 4 * 2.39 28.97 V1TR 32.2-24.1 37.07 54-16.93 - - 124 187 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, Ton is packet duration Height (cm) Polarity Page 76 of 121 This report shall not be reproduced except in full, without the written approval of.

LOW CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 37.06 Pk 32.2-24.2 45.06 - - 74-28.94 319 134 V 2 * 2.377 47.65 Pk 32.1-24.1 55.65 - - 74-18.35 319 134 V 3 * 2.39 27.05 V1TR 32.2-24.2 35.05 54-18.95 - - 319 134 V 4 * 2.389 29.36 V1TR 32.2-24.1 37.46 54-16.54 - - 319 134 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 77 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (LOW CHANNEL, CHARGER) LOW CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 36.39 Pk 32.2-24.2 44.39 - - 74-29.61 59 111 H 2 * 2.377 47.9 Pk 32.1-24.1 55.9 - - 74-18.1 59 111 H 3 * 2.39 27.09 V1TR 32.2-24.2 35.09 54-18.91 - - 59 111 H 4 * 2.389 29.75 V1TR 32.2-24.1 37.85 54-16.15 - - 59 111 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 78 of 121 This report shall not be reproduced except in full, without the written approval of.

LOW CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 35.21 Pk 32.2-24.2 43.21 - - 74-30.79 133 113 V 2 * 2.377 42.04 Pk 32.1-24.1 50.04 - - 74-23.96 133 113 V 3 * 2.39 25.96 V1TR 32.2-24.2 33.96 54-20.04 - - 133 113 V 4 * 2.389 27.83 V1TR 32.2-24.1 35.93 54-18.07 - - 133 113 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 79 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (HIGH CHANNEL, STANDALONE) HIGH CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 40.71 Pk 32.4-24.7 48.41 - - 74-25.59 132 106 H 3 * 2.484 31.93 V1TR 32.4-24.7 39.63 54-14.37 - - 132 106 H 4 * 2.484 32.02 V1TR 32.4-24.7 39.72 54-14.28 - - 132 106 H 2 2.506 45.44 Pk 32.5-24.8 53.14 - - 74-20.86 132 106 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 80 of 121 This report shall not be reproduced except in full, without the written approval of.

HIGH CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 39.11 Pk 32.4-24.7 46.81 - - 74-27.19 38 108 V 3 * 2.484 29.84 V1TR 32.4-24.7 37.54 54-16.46 - - 38 108 V 4 * 2.487 30.55 V1TR 32.4-24.7 38.25 54-15.75 - - 38 108 V 2 2.506 41.96 Pk 32.5-24.8 49.66 - - 74-24.34 38 108 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 81 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (HIGH CHANNEL, CHARGER) HIGH CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF Amp/Cbl/ AT0069 Fltr/Pad (db/m) Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 41.45 Pk 32.4-24.7 49.15 - - 74-24.85 59 111 H 3 * 2.484 33.15 V1TR 32.4-24.7 40.85 54-13.15 - - 59 111 H 4 * 2.484 33.43 V1TR 32.4-24.7 41.13 54-12.87 - - 59 111 H 2 2.506 47.78 Pk 32.5-24.8 55.48 - - 74-18.52 59 111 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 82 of 121 This report shall not be reproduced except in full, without the written approval of.

HIGH CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 38.77 Pk 32.4-24.7 46.47 - - 74-27.53 33 109 V 3 * 2.484 28.11 V1TR 32.4-24.7 35.81 54-18.19 - - 33 109 V 4 * 2.486 30.15 V1TR 32.4-24.7 37.85 54-16.15 - - 33 109 V 2 2.506 41.91 Pk 32.5-24.8 49.61 - - 74-24.39 33 109 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 83 of 121 This report shall not be reproduced except in full, without the written approval of.

HARMONICS AND SPURIOUS EMISSIONS Standalone Low Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.352 43.24 PK-U 31.8-24 51.04 - - 74-22.96 73 173 H * 2.352 25.98 V1TR 31.8-24 33.78 54-20.22 - - 73 173 H 3 * 4.804 44.81 PK-U 34-31.7 47.11 - - 74-26.89 241 141 H * 4.804 38.94 V1TR 34-31.7 41.24 54-12.76 - - 241 141 H 7 * 4.804 46.67 PK-U 34-31.7 48.97 - - 74-25.03 237 272 V * 4.804 41.99 V1TR 34-31.7 44.29 54-9.71 - - 237 272 V 2 3.202 40.65 Pk 33.4-33.4 40.65 - - - - 0-360 102 H 4 7.206 35.58 Pk 35.6-28.7 42.48 - - - - 0-360 199 H 5 9.608 37.27 Pk 36.6-27.1 46.77 - - - - 0-360 199 H 6 3.202 36.96 Pk 33.4-33.4 36.96 - - - - 0-360 102 V 8 7.206 40.78 Pk 35.6-28.7 47.68 - - - - 0-360 199 V 9 9.608 42.63 Pk 36.6-27.1 52.13 - - - - 0-360 102 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 84 of 121 This report shall not be reproduced except in full, without the written approval of.

Standalone Mid Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.882 43.24 PK-U 34.1-31.5 45.84 - - 74-28.16 251 137 H * 4.882 37.03 V1TR 34.1-31.5 39.63 54-14.37 - - 251 137 H 3 * 7.323 41.51 PK-U 35.5-28.4 48.61 - - 74-25.39 169 386 H * 7.323 34.46 V1TR 35.5-28.4 41.56 54-12.44 - - 169 386 H 6 * 4.882 46.61 PK-U 34.1-31.5 49.21 - - 74-24.79 243 295 V * 4.882 41.92 V1TR 34.1-31.5 44.52 54-9.48 - - 243 295 V 7 * 7.323 43.12 PK-U 35.5-28.4 50.22 - - 74-23.78 238 115 V * 7.323 36.37 V1TR 35.5-28.4 43.47 54-10.53 - - 238 115 V 1 3.254 38.94 Pk 33.1-33.7 38.34 - - - - 0-360 102 H 4 9.765 36.13 Pk 36.8-26.4 46.53 - - - - 0-360 102 H 5 3.255 42.72 Pk 33.1-33.7 42.12 - - - - 0-360 101 V 8 9.763 38.86 Pk 36.8-26.4 49.26 - - - - 0-360 101 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 85 of 121 This report shall not be reproduced except in full, without the written approval of.

Standalone High Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.96 43.9 PK-U 34.1-31.6 46.4 - - 74-27.6 343 222 H * 4.96 36.51 V1TR 34.1-31.6 39.01 54-14.99 - - 343 222 H 3 * 7.44 41.25 PK-U 35.5-28.7 48.05 - - 74-25.95 168 221 H * 7.44 34.04 V1TR 35.5-28.7 40.84 54-13.16 - - 168 221 H 6 * 4.96 44.64 PK-U 34.1-31.6 47.14 - - 74-26.86 245 400 V * 4.96 38.92 V1TR 34.1-31.6 41.42 54-12.58 - - 245 400 V 7 * 7.44 46.08 PK-U 35.5-28.7 52.88 - - 74-21.12 285 183 V * 7.44 40.87 V1TR 35.5-28.7 47.67 54-6.33 - - 285 183 V 1 3.307 42.78 Pk 32.7-33.5 41.98 - - - - 0-360 199 H 5 3.307 37.87 Pk 32.7-33.5 37.07 - - - - 0-360 101 V 4 9.92 38.16 Pk 37.1-26.5 48.76 - - - - 0-360 199 H 8 9.92 42.24 Pk 37.1-26.5 52.84 - - - - 0-360 101 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 86 of 121 This report shall not be reproduced except in full, without the written approval of.

Charger Low Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.377 48.59 PK-U 32.1-24.1 56.59 - - 74-17.41 64 154 H * 2.377 27.35 V1TR 32.1-24.1 35.35 54-18.65 - - 64 154 H 3 * 4.804 44.51 PK-U 34-31.7 46.81 - - 74-27.19 227 223 H * 4.804 38.98 V1TR 34-31.7 41.28 54-12.72 - - 227 223 H 7 * 4.804 48.49 PK-U 34-31.7 50.79 - - 74-23.21 210 239 V * 4.804 44.84 V1TR 34-31.7 47.14 54-6.86 - - 210 239 V 2 3.202 41.71 Pk 33.4-33.4 41.71 - - - - 0-360 101 H 6 3.202 38.06 Pk 33.4-33.4 38.06 - - - - 0-360 102 V 4 7.206 36.23 Pk 35.6-28.7 43.13 - - - - 0-360 199 H 8 7.206 40.45 Pk 35.6-28.7 47.35 - - - - 0-360 199 V 5 9.607 40.45 Pk 36.6-27.1 49.95 - - - - 0-360 199 H 9 9.608 43.4 Pk 36.6-27.1 52.9 - - - - 0-360 102 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 87 of 121 This report shall not be reproduced except in full, without the written approval of.

Charger Mid Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.882 46.39 PK-U 34.1-31.5 48.99 - - 74-25.01 197 244 H * 4.882 42.03 V1TR 34.1-31.5 44.63 54-9.37 - - 197 244 H 3 * 7.323 41.12 PK-U 35.5-28.4 48.22 - - 74-25.78 209 193 H * 7.323 33.01 V1TR 35.5-28.4 40.11 54-13.89 - - 209 193 H 6 * 4.882 45.87 PK-U 34.1-31.5 48.47 - - 74-25.53 199 222 V * 4.882 41.42 V1TR 34.1-31.5 44.02 54-9.98 - - 199 222 V 7 * 7.323 43.62 PK-U 35.5-28.4 50.72 - - 74-23.28 267 186 V * 7.323 37.31 V1TR 35.5-28.4 44.41 54-9.59 - - 267 186 V 1 3.255 43.31 Pk 33.1-33.7 42.71 - - - - 0-360 102 H 5 3.255 38.4 Pk 33.1-33.7 37.8 - - - - 0-360 102 V 8 8.95 33.5 Pk 35.9-27.8 41.6 - - - - 0-360 199 V 4 9.763 36.45 Pk 36.8-26.4 46.85 - - - - 0-360 199 H 9 9.764 42.06 Pk 36.8-26.4 52.46 - - - - 0-360 199 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 88 of 121 This report shall not be reproduced except in full, without the written approval of.

Charger High Channel Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.96 43.76 PK-U 34.1-31.6 46.26 - - 74-27.74 193 224 H * 4.96 36.96 V1TR 34.1-31.6 39.46 54-14.54 - - 193 224 H 3 * 7.44 42.03 PK-U 35.5-28.7 48.83 - - 74-25.17 215 182 H * 7.44 34.5 V1TR 35.5-28.7 41.3 54-12.7 - - 215 182 H 6 * 4.96 45.24 PK-U 34.1-31.6 47.74 - - 74-26.26 254 229 V * 4.96 38.83 V1TR 34.1-31.6 41.33 54-12.67 - - 254 229 V 7 * 7.44 45.3 PK-U 35.5-28.7 52.1 - - 74-21.9 280 180 V * 7.44 39.56 V1TR 35.5-28.7 46.36 54-7.64 - - 280 180 V 1 3.307 42.52 Pk 32.7-33.5 41.72 - - - - 0-360 102 H 5 3.307 38.64 Pk 32.7-33.5 37.84 - - - - 0-360 102 V 4 9.92 37.48 Pk 37.1-26.5 48.08 - - - - 0-360 102 H 8 9.92 40.81 Pk 37.1-26.5 51.41 - - - - 0-360 199 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 89 of 121 This report shall not be reproduced except in full, without the written approval of.

9.2.2. ENHANCED DATA RATE 8PSK MODULATION RESTRICTED BANDEDGE (LOW CHANNEL, STANDALONE) LOW CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 2.377 44.55 Pk 32.1-24.1 52.55 - - 74-21.45 67 102 H 1 * 2.39 39.1 Pk 32.2-24.2 47.1 - - 74-26.9 67 102 H 3 * 2.39 27.44 V1TR 32.2-24.2 35.44 54-18.56 - - 67 102 H 4 * 2.39 27.46 V1TR 32.2-24.1 35.56 54-18.44 - - 67 102 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 90 of 121 This report shall not be reproduced except in full, without the written approval of.

LOW CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 2.377 43.74 Pk 32.1-24.1 51.74 - - 74-22.26 40 115 V 1 * 2.39 40.85 Pk 32.2-24.2 48.85 - - 74-25.15 40 115 V 3 * 2.39 27.06 V1TR 32.2-24.2 35.06 54-18.94 - - 40 115 V 4 * 2.39 27.08 V1TR 32.2-24.2 35.08 54-18.92 - - 40 115 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 91 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (LOW CHANNEL, CHARGER) LOW CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 42.11 Pk 32.2-24.2 50.11 - - 74-23.89 162 238 H 2 * 2.377 45.06 Pk 32.1-24.1 53.06 - - 74-20.94 162 238 H 3 * 2.39 27.77 V1TR 32.2-24.2 35.77 54-18.23 - - 162 238 H 4 * 2.39 27.9 V1TR 32.2-24.2 35.9 54-18.1 - - 162 238 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 92 of 121 This report shall not be reproduced except in full, without the written approval of.

LOW CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF Amp/Cbl/ AT0069 Fltr/Pad (db/m) Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.39 39 Pk 32.2-24.2 47 - - 74-27 334 348 V 2 * 2.389 39.6 Pk 32.2-24.1 47.7 - - 74-26.3 334 348 V 3 * 2.39 26.36 V1TR 32.2-24.2 34.36 54-19.64 - - 334 348 V 4 * 2.389 26.4 V1TR 32.2-24.1 34.5 54-19.5 - - 334 348 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 93 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (HIGH CHANNEL, STANDALONE) HIGH CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 38.22 Pk 32.4-24.7 45.92 - - 74-28.08 210 292 H 2 * 2.484 41.06 Pk 32.4-24.7 48.76 - - 74-25.24 210 292 H 3 * 2.484 28.71 V1TR 32.4-24.7 36.41 54-17.59 - - 210 292 H 4 * 2.484 28.56 V1TR 32.4-24.7 36.26 54-17.74 - - 210 292 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 94 of 121 This report shall not be reproduced except in full, without the written approval of.

HIGH CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 35.67 Pk 32.4-24.7 43.37 - - 74-30.63 323 161 V 3 * 2.484 26.23 V1TR 32.4-24.7 33.93 54-20.07 - - 323 161 V 4 * 2.484 26.33 V1TR 32.4-24.7 34.03 54-19.97 - - 323 161 V 2 2.519 37.95 Pk 32.5-24.9 45.55 - - 74-28.45 323 161 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 95 of 121 This report shall not be reproduced except in full, without the written approval of.

RESTRICTED BANDEDGE (HIGH CHANNEL, CHARGER) HIGH CHANNEL RESTRICTED, HORIZ Marker Frequency (GHz) Meter (dbuv) Det AF Amp/Cbl AT0069 /Fltr/Pad (db/m) Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 38.36 Pk 32.4-24.7 46.06 - - 74-27.94 243 376 H 2 * 2.484 41.24 Pk 32.4-24.7 48.94 - - 74-25.06 243 376 H 3 * 2.484 28.58 V1TR 32.4-24.7 36.28 54-17.72 - - 243 376 H 4 * 2.484 28.4 V1TR 32.4-24.7 36.1 54-17.9 - - 243 376 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 96 of 121 This report shall not be reproduced except in full, without the written approval of.

HIGH CHANNEL RESTRICTED, VERT Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Average Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.484 38.09 Pk 32.4-24.7 45.79 - - 74-28.21 17 387 V 2 * 2.485 41.19 Pk 32.4-24.7 48.89 - - 74-25.11 17 387 V 3 * 2.484 28.59 V1TR 32.4-24.7 36.29 54-17.71 - - 17 387 V 4 * 2.484 28.61 V1TR 32.4-24.7 36.31 54-17.69 - - 17 387 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 97 of 121 This report shall not be reproduced except in full, without the written approval of.

HARMONICS AND SPURIOUS EMISSIONS STANDALONE LOW CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.804 44.03 PK-U 34-31.7 46.33 - - 74-27.67 68 260 H * 4.804 34.66 V1TR 34-31.7 36.96 54-17.04 - - 68 260 H 5 * 4.804 42.9 PK-U 34-31.7 45.2 - - 74-28.8 241 101 V * 4.804 34.09 V1TR 34-31.7 36.39 54-17.61 - - 241 101 V 1 3.202 37.79 Pk 33.4-33.4 37.79 - - - - 0-360 102 H 3 7.206 31.54 Pk 35.6-28.7 38.44 - - - - 0-360 199 H 4 9.608 30.44 Pk 36.6-27.1 39.94 - - - - 0-360 199 H 6 7.206 37.01 Pk 35.6-28.7 43.91 - - - - 0-360 199 V 7 9.608 33.15 Pk 36.6-27.1 42.65 - - - - 0-360 102 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 98 of 121 This report shall not be reproduced except in full, without the written approval of.

STANDALONE MID CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 4 * 7.323 38.76 PK-U 35.5-28.4 45.86 - - 74-28.14 209 166 H * 7.323 29.4 V1TR 35.5-28.4 36.5 54-17.5 - - 209 166 H 5 * 7.323 40.98 PK-U 35.5-28.4 48.08 - - 74-25.92 267 167 V * 7.323 32.47 V1TR 35.5-28.4 39.57 54-14.43 - - 267 167 V 1 2.415 36.8 Pk 32.3-24.4 44.7 - - - - 0-360 102 H 2 3.254 37.72 Pk 33.1-33.7 37.12 - - - - 0-360 102 H 3 5.548 34.67 Pk 34.6-31.5 37.77 - - - - 0-360 102 H 6 9.763 32.21 Pk 36.8-26.4 42.61 - - - - 0-360 101 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 99 of 121 This report shall not be reproduced except in full, without the written approval of.

STANDALONE HIGH CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 3 * 7.44 39.11 PK-U 35.5-28.7 45.91 - - 74-28.09 217 185 H * 7.44 28.51 V1TR 35.5-28.7 35.31 54-18.69 - - 217 185 H 5 * 7.44 42.06 PK-U 35.5-28.7 48.86 - - 74-25.14 300 205 V * 7.44 33.55 V1TR 35.5-28.7 40.35 54-13.65 - - 300 205 V 1 2.454 35.21 Pk 32.3-24.5 43.01 - - - - 0-360 199 H 2 5.567 34.15 Pk 34.6-31.2 37.55 - - - - 0-360 102 H 6 9.919 30.17 Pk 37.1-26.6 40.67 - - - - 0-360 101 V 4 12.931 29.66 Pk 39.2-25 43.86 - - - - 0-360 102 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 100 of 121 This report shall not be reproduced except in full, without the written approval of.

CHARGER LOW CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 1 * 2.377 43.59 PK-U 32.1-24.1 51.59 - - 74-22.41 77 369 H * 2.377 26.2 V1TR 32.1-24.1 34.2 54-19.8 - - 77 369 H 2 3.203 37.49 Pk 33.4-33.4 37.49 - - - - 0-360 101 H 3 7.206 32.02 Pk 35.6-28.7 38.92 - - - - 0-360 101 H 5 7.206 35.87 Pk 35.6-28.7 42.77 - - - - 0-360 200 V 6 9.607 32.56 Pk 36.6-27.1 42.06 - - - - 0-360 102 V 4 9.608 31.48 Pk 36.6-27.1 40.98 - - - - 0-360 101 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 101 of 121 This report shall not be reproduced except in full, without the written approval of.

CHARGER MID CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ Fltr/Pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 3 * 7.323 38.62 PK-U 35.5-28.4 45.72 - - 74-28.28 196 270 H * 7.323 27.84 V1TR 35.5-28.4 34.94 54-19.06 - - 196 270 H 5 * 7.323 41.28 PK-U 35.5-28.4 48.38 - - 74-25.62 282 216 V * 7.323 33.05 V1TR 35.5-28.4 40.15 54-13.85 - - 282 216 V 1 2.416 35.29 Pk 32.3-24.4 43.19 - - - - 0-360 199 H 2 3.255 38.5 Pk 33.1-33.7 37.9 - - - - 0-360 199 H 4 3.255 36.29 Pk 33.1-33.7 35.69 - - - - 0-360 101 V 6 9.763 31.2 Pk 36.8-26.4 41.6 - - - - 0-360 199 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 102 of 121 This report shall not be reproduced except in full, without the written approval of.

CHARGER HIGH CHANNEL Marker Frequency (GHz) Meter (dbuv) Det AF AT0069 (db/m) Amp/Cbl/ fltr/pad Corrected Avg Limit Margin Peak Limit PK Margin Azimuth (Degs) 2 * 4.556 40.25 PK-U 34-32 42.25 - - 74-31.75 339 247 H * 4.558 29 V1TR 34-32 31 54-23 - - 339 247 H 4 * 7.441 39.28 PK-U 35.5-28.7 46.08 - - 74-27.92 16 390 H * 7.44 28.92 V1TR 35.5-28.7 35.72 54-18.28 - - 16 390 H 5 * 7.44 41.65 PK-U 35.5-28.7 48.45 - - 74-25.55 282 188 V * 7.44 33.18 V1TR 35.5-28.7 39.98 54-14.02 - - 282 188 V 1 3.21 35.66 Pk 33.4-33.2 35.86 - - - - 0-360 102 H 3 6.469 33.15 Pk 35.4-30.1 38.45 - - - - 0-360 102 H 6 14.875 29.01 Pk 39.9-23.6 45.31 - - - - 0-360 199 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 103 of 121 This report shall not be reproduced except in full, without the written approval of.

9.2.3. WORSE-CASE 18-26GHz SPURIOUS EMISSIONS 18 to 26GHz (STANDALONE) Marker Frequency (GHz) Meter (dbuv) Det AF AT0076 (db/m) Amp/Cbl Corrected Average Limit Margin Peak Limit Margin Azimuth (Degs) 2 * 20.411 46.36 PK-U 33.4-40.3 39.46 - - 74-34.54 33 360 H * 20.41 35.77 V1TR 33.4-40.3 28.87 54-25.13 - - 33 360 H 4 * 22.881 47.51 PK-U 33.7-39.4 41.81 - - 74-32.19 344 187 H * 22.878 35.89 V1TR 33.7-39.4 30.19 54-23.81 - - 344 187 H 1 * 20.38 46.95 PK-U 33.3-39.9 40.35 - - 74-33.65 285 398 V * 20.379 35.82 V1TR 33.3-39.9 29.22 54-24.78 - - 285 398 V 3 21.688 46.88 Pk 33.7-39.7 40.88 - - - - 0-360 202 V 5 24.654 46.58 Pk 34.6-38.5 42.68 - - - - 0-360 250 H 6 25.778 45.96 Pk 34.8-37.7 43.06 - - - - 0-360 252 V * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 104 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS 18 to 26GHz (CHARGER) Marker Frequency (GHz) Meter (dbuv) Det AF AT0076 (db/m) Amp/Cbl Corrected Average Limit Margin Peak Limit Margin Azimuth (Degs) 1 * 19.107 48.18 PK-U 32.9-40.8 40.28 - - 74-33.72 110 192 H * 19.107 36.5 V1TR 32.9-40.8 28.6 54-25.4 - - 110 192 H 3 * 22.127 48.15 PK-U 33.9-39.9 42.15 - - 74-31.85 0 291 H * 22.126 36.5 V1TR 33.9-39.9 30.5 54-23.5 - - 0 291 H 2 * 19.529 50.74 PK-U 32.9-40.4 43.24 - - 74-30.76 245 145 V * 19.529 41.47 V1TR 32.9-40.4 33.97 54-20.03 - - 245 145 V 4 * 22.227 47.25 PK-U 33.7-39.6 41.35 - - 74-32.65 203 160 V * 22.227 35.93 V1TR 33.7-39.6 30.03 54-23.97 - - 203 160 V 5 23.562 47.68 Pk 34.2-39.2 42.68 - - - - 0-360 299 V 6 26.047 46.29 Pk 35.1-37.5 43.89 - - - - 0-360 249 H * - indicates frequency in CFR47 Pt 15 / IC RSS-Restricted Band Pk - Peak detector PK-U: Maximum Peak V1TR: VB=1/Ton, where: Ton is packet duration Height (cm) Polarity Page 105 of 121 This report shall not be reproduced except in full, without the written approval of.

9.3. WORST-CASE BELOW 1 GHz Note: All measurements were made at a test distance of 3 m. The limits in the plots and tabular data are the FCC/IC limits extrapolated from the specification distance (300 m from 9-490 khz and 30 m from 490 khz 30 MHz) to the measurement distance to clearly show the relative levels of fundamental and spurious emissions and demonstrate compliance with the requirement that the level of any spurious emissions be below the level of the intentionally transmitted signal. The extrapolation factor for the limits were 40*Log (specification distance / test distance). The anechoic chamber has been properly calibrated so that the measurement results correspond to what would be obtained from an open field sites. SPURIOUS EMISSIONS 9kHz to 30MHz (WORST-CASE CONFIGURATION,STANDALONE) Marker Frequency (MHz) Meter (dbuv) Det AT0079 AF (db/m) Cbl Corrected db(uvolts/meter) FCC 15.209 (projected to 3m) Margin Azimuth (Degs) 1.01622 45.13 Pk 16.4.1 61.63 123.4-61.77 0-360 2.03588 41.85 Pk 13.6.1 55.55 116.51-60.96 0-360 3.36176 40.16 Pk 11.9.1 52.16 96.44-44.28 0-360 4 5.16955 19.15 Pk 11.3.4 30.85 69.54-38.69 0-360 5 23.3121 14.86 Pk 9.4.8 25.06 69.54-44.48 0-360 6 28.59112 15.06 Pk 8.6.9 24.56 69.54-44.98 0-360 Pk - Peak detector Page 106 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS 9kHz to 30MHz (WORST-CASE CONFIGURATION,CHARGER) Marker Frequency (MHz) Meter (dbuv) Det AT0079 AF (db/m) Cbl Corrected db(uvolts/meter) FCC 15.209 (projected to 3m) Margin Azimuth (Degs) 1.01844 46.49 Pk 15.5.1 62.09 122.29-60.2 0-360 2.35878 40.31 Pk 11.9.1 52.31 96.51-44.2 0-360 3 1.2237 28.96 Pk 11.9.2 41.06 65.85-24.79 0-360 4 5.16657 20.82 Pk 11.3.4 32.52 69.54-37.02 0-360 5 23.14508 15.87 Pk 9.5.8 26.17 69.54-43.37 0-360 6 23.28227 18.4 Pk 9.4.8 28.6 69.54-40.94 0-360 Pk - Peak detector Page 107 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS 30 TO 1000 MHz (WORST-CASE CONFIGURATION,STANDALONE) Marker Frequency (MHz) Meter (dbuv) Det AF AT0074 (db/m) Port 0 Factors Corrected QPk Limit Margin Azimuth (Degs) 1 30.8925 29.69 Pk 25.5-31.8 23.39 40-16.61 0-360 299 H 2 53.9275 35.52 Pk 11.9-31.6 15.82 40-24.18 0-360 102 V 3 139.99 30.48 Pk 17.5-30.7 17.28 43.52-26.24 0-360 102 V 4 185.635 32.31 Pk 15.8-30.4 17.71 43.52-25.81 0-360 102 V 5 201 31.61 Pk 17.1-30.2 18.51 43.52-25.01 0-360 199 V 6 537 30.07 Pk 22.7-28.7 24.07 46.02-21.95 0-360 199 V Pk - Peak detector FCC Part 15C 30-1000MHz.TST Rev 9.5 20 Aug 2015 Height (cm) Polarity Page 108 of 121 This report shall not be reproduced except in full, without the written approval of.

SPURIOUS EMISSIONS 30 TO 1000 MHz (WORST-CASE CONFIGURATION, CHARGER) Marker Frequency (MHz) Meter (dbuv) Det AF AT0074 (db/m) Port 0 Factors Corrected QPk Limit Margin Azimuth (Degs) 1 34.845 40.31 Pk 22.4-31.7 31.01 40-8.99 0-360 102 V 2 66.295 50.59 Pk 12.2-31.2 31.59 40-8.41 0-360 102 V 3 92.985 50.53 Pk 12.3-31 31.83 43.52-11.69 0-360 102 V 4 99.53 48.76 Pk 14.3-31.1 31.96 43.52-11.56 0-360 102 V 5 130.47 44.22 Pk 18.1-30.7 31.62 43.52-11.9 0-360 199 H 6 145.2388 44.6 Pk 17.1-30.7 31 43.52-12.52 0-360 199 H Pk - Peak detector FCC Part 15C 30-1000MHz.TST Rev 9.5 20 Aug 2015 Height (cm) Polarity Page 109 of 121 This report shall not be reproduced except in full, without the written approval of.

10. POWER LINE CONDUCTED LIMITS ANSI C63.10 Section 6.2 FCC 15.207 (a) RSS-Gen 7.2.2 TEST PROCEDURE The EUT is placed on a non-conducting table 40 cm from the vertical ground plane and 80 cm above the horizontal ground plane. The EUT is configured in accordance with ANSI C63.10. The receiver is set to a resolution bandwidth of 9 khz. Peak detection is used unless otherwise noted as quasi-peak or average. Line conducted data is recorded for both NEUTRAL and HOT lines. RESULTS Page 110 of 121 This report shall not be reproduced except in full, without the written approval of.

POWER LINE CONDUCTED RESULTS (CHARGER) Range 1: Line-L1.15-30MHz Marker Frequency (MHz) Meter (dbuv) Det LISN VCF [db] Cbl/Limiter Corrected dbuv Class-B QP Limit Margin Class-B Avg Limit 3.159 38.04 Pk.2 10 48.24 65.52-17.28 - - Margin 4.159 6.41 Av.2 10 16.61 - - 55.52-38.91 5.372 30.5 Pk.1 10 40.6 58.46-17.86 - - 6.372 11.54 Av.1 10 21.64 - - 48.46-26.82 11 22.128 21 Pk.3 10.6 31.9 60-28.1 - - 12 22.155 4.76 Av.3 10.6 15.66 - - 50-34.34 Pk - Peak detector Av - Average detection Page 111 of 121 This report shall not be reproduced except in full, without the written approval of.

Range 2: Line-L2.15-30MHz Marker Frequency (MHz) Meter (dbuv) Det LISN VCF [db] Cbl/Limiter Corrected dbuv Class-B QP Limit Margin Class-B Avg Limit 1.156 37.67 Pk.2 10 47.87 65.67-17.8 - - Margin 2.156 7.38 Av.2 10 17.58 - - 55.67-38.09 7.366 26.32 Pk.1 10 36.42 58.59-22.17 - - 8.366 2.76 Av.1 10 12.86 - - 48.59-35.73 9 8.904 25.03 Pk.1 10.3 35.43 60-24.57 - - 10 8.895 7.37 Av.1 10.3 17.77 - - 50-32.23 Pk - Peak detector Av - Average detection Page 112 of 121 This report shall not be reproduced except in full, without the written approval of.

11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO Page 113 of 121 This report shall not be reproduced except in full, without the written approval of.

RADIATED RF MEASUREMENT SETUP (BELOW 1 GHz) RADIATED FRONT PHOTO (STANDALONE BELOW 1 GHz) Page 114 of 121 This report shall not be reproduced except in full, without the written approval of.

RADIATED BACK PHOTO (CHARGER BELOW 1 GHz) Page 115 of 121 This report shall not be reproduced except in full, without the written approval of.

RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) RADIATED PHOTO (STANDALONE ABOVE 1 GHz) Page 116 of 121 This report shall not be reproduced except in full, without the written approval of.

RADIATED PHOTO (CHARGER ABOVE 1 GHz) Page 117 of 121 This report shall not be reproduced except in full, without the written approval of.

RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS FRONT PHOTO Y-AXIS FRONT PHOTO Page 118 of 121 This report shall not be reproduced except in full, without the written approval of.

Page 119 of 121 This report shall not be reproduced except in full, without the written approval of.

Z-AXIS FRONT PHOTO Page 120 of 121 This report shall not be reproduced except in full, without the written approval of.

POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO END OF REPORT Page 121 of 121 This report shall not be reproduced except in full, without the written approval of.