Compact Motorized Using the superior characteristics of the best selling ELMY butterfly valve actuator, we developed an improved successor, the. With a replaceable control circuit board, tough metal gears, new limit cam mechanism, a new clutch mechanism, and an improved watertight design, the actuator is even better than before. Features Circuit board is easily replaceable to meet different requirements. New adjustable limit switch cam plate. Waterproof design protects against rain water or condensation Declutchable handwheel for ease of operation and maximum safety. High output torque and compact in size. Types to -0
Type Output torque (Nm) Power source (V) Motor capacity (W) Travel time (/Hz) (sec) Rating (min) Insulation Type of motor and its protective device Space heater Position limit switch Torque limit switch Mechanical limit stop Conduit connections Enclosure Manual operation Number of turns for handle/handwheel Paint finish Options Type 0 0. No space heater with servounit.. With speed controller unit. Detachable handle. turns Specifications Type Type 9 9 0 /0 (0/) AC 000 /Hz 0 ) Potentiometer and 0 ) Intermediate limit switch (no voltage) ) Servounit (AC 0mA, DCV, 00V) ) Speed controller unit Type. /0 (/0) Type 9 0 Class E Reversible motor with built-in thermal protector Supplied under the standard specifications One each at the open and close positions Extra position limit switches (under no voltage) None End of travel positioning bolt built-in G / (PF /) ports JIS C 090 (IP ), Class, dust and water-jet proof type Declutchable handwheel. turns Epoxy-melanin baked with Munsell. BG / Type 0 90 / /0 (0/0) (/900) -0
(Approx.) (Approx.) W (Approx.) W W Dimensions Type 0 P A Types and. A P H H F K E G PF H H Type Types and K F F K G PF P A P A E G PF H H E F K (Approx.) G PF H H Dimensions / Weight Motor type Type 0 Type Type Type. Type Type ( ): Demension with servounit Dimensionmm H H P A E F K () (9) 9() 9() 0() 0() 0 0 0 W 0 0 Approx. weight kg...... -0
Mounting details D F F D A B E A B E C G C G Mounting flange details Type 0 Type Type Type. Type Type type ISO F0 ISO F0 Tomoe original ISO F0 Tomoe original ISO F0 ISO F Tomoe original ISO F0 ISO F ISO F Tomoe original ISO F ISO F Tomoe original A B C D 0 0 0 0 0 0 0 0 0 0 0 0................... 0 0 0 0 0 0 0 0 9 0 9 0 0 0 0 0 0 0 0 0 E 0. 0.0 0.0.0.0 0.0.0 F 90 90 Qty M 0 0 0 0 G P............0..0..0.0.0.0.0 Dep. 0 0 0 0-0
Terminal board connection diagram () FG contact should be grounded. () If space heater (option) is used, round contact should be connected to contacts and. () Power source for control unit of V series and V series is same, but power source for actuator motor is not. Wirng diagram Input voltage: single phase alternating current /Hz Heater Common Stop Output voltage Output voltage for open side for closed side Terminal block screw size: M (with washer) 9 0 COM NC NO COM NC NO side Extra limit switch for open side Extra limit switch for closed side Mid point side Output for potentiometer (option) F.G. Terminal board Terminal No. Specification Standard with extra position limit switches With intermediate limit switches With a potentiometer and extra position limit switches With a potentiometer and intermediate limit switches Heater COMMON switch switch Extra position limit switch,open end intermediate limit switch COMMON intermediate limit switch NC intermediate limit switch NO Extra position limit switch, close end intermediate limit switch COMMON intermediate limit switch NC intermediate limit switch NO Potentiometer Potentiometer Potentiometer Earth (F.G.) d d, and 9 are out of use. : wired : not wired Contact output Terminal No. COM OPEN 9 CLOSE Contacts Connection Common with No. and 9 Connect with No. at open position Connect with No. at close position Capacity ACV-0A -0
. On-off use with extra limit switch (as standard) with intermediate limit switch (as option) Recommended fuse and non-fuse breaker Type Power source and frequency Recommended capacity for fuse Recommended capacity for non-fuse breaker 0, V/0V Hz/Hz V/0V Hz/Hz A A A A,. V/0V Hz/Hz V/0V Hz/Hz A A A A, V/0V Hz/Hz V/0V Hz/Hz A A A A. Modulating use with speed control unit (as option) with servo unit (as option) Type Power source and frequency Recommended capacity for fuse Recommended capacity for non-fuse breaker 0, V/0V Hz/Hz V/0V Hz/Hz A A.A A,. V/0V Hz/Hz V/0V Hz/Hz A A A A, V/0V Hz/Hz V/0V Hz/Hz 0A A 0A A -0
Wiring diagrams (Control options) Standard With extra position limit switch (non-voltage) Purpose To send non-voltage full-open and full-closed signals by switching on and off. ACTUATOR WIRING LS open LS shut M Thermal protector Heater O.L.S S.L.S 0 Stop Limit switch contact development Fully closed Fully open O.L.S S.L.S LS open Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. LS shut With intermediate limit switch Purpose To send intermediate open and close signals by switching on and off, and to stop the valve at intermediate positions. Options Intermediate limit switches (two, non-voltage) Limit switch contact development Thermal protector Heater M O.L.S S.L.S L S. L S. 0 Stop ACTUATOR WIRING O.L.S S.L.S LS. Fully closed Intermediate position Intermediate position Fully open Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. LS. -0 9
Wiring diagrams (Control options) With potentiometer and extra position limit switch (non-voltage) Purpose To control valve opening by resistance variations and send non-voltage full-open and full-closed signals by switching on and off. Options or 0 potentiometer ACTUATOR WIRING LS open LS shut Potentiometer M Thermal protector Heater O.L.S S.L.S 9 0 Stop Limit switch contact development Fully closed Fully open O.L.S S.L.S LS open LS shut Notes. Do not use a switch for two or more of motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. With thermal output ACTUATOR WIRING Thermal protector Heater M O.LS S.LS Stop LS open LS shut 9 0 Limit switch contact development Fully closed O.L.S Fully open S.L.S LS open LS shut Notes. Outputs when thermal operation shall be b contacts.. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switche work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur.. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. -0
Wiring diagrams (Control options) With servo unit, potentiometer and extra position limit switch (non-voltage) Purpose To control valve opening by resistance variations, send intermediate open and close signals, and to stop the valve at intermediate positions by switching on and off. ACTUATOR WIRING Options or 0 potentiometer Intermediate limit switches (two, non-voltage) M L S. L S. Potentiometer Thermal protector Heater O.L.S S.L.S 9 0 Stop Notes. The contact capacity of the extra limit switch is VAC-0 A (min. 0. A). For anything below this contact capacity ( ma to ma, to 0 V), please use specifications for minute loads. Controller Specifications with servo unit Input signal DC. to 0 ma (Option to V, 0 to 0 V) Output signal DC. to 0 ma Contact output Fully open, Fully closed (non voltage) (capacity: AC V-0 A (over 0. A)) Dead band % to % variable Operation frequency rate ED % or less Zero span adjustment range to % FS Span adjustment 0 to 0% FS Switching of RA and DA By changing connector Operation temperature 0 to degrees C -09
Parts list for With servo unit inside of types 0,, and. Terminal 9 0 Dog for open position Dog for closed position Potentiometer Connector for motor Connector for motor capacitor RA: connector for potentiometer DA: connector for potentiometer 9 RA: wiring connector 0 DA: wiring connector Trimmer for hysterisis adjustment Trimmer for zero adjustment Trimmer for span adjustment Trimmer for output zero adjustment Trimmer for output span adjustment Remarks: When Z is adjusted, then please adjust S too. When Z is adjusted, then please adjust S too. With servo unit inside of types and Terminal Dog for open position Dog for closed position Potentiometer Connector for motor Connector for motor capacitor RA: connector for potentiometer Trimmer for hysterisis adjustment Trimmer for zero adjustment Trimmer for span adjustment Trimmer for output zero adjustment Trimmer for output span adjustment Remarks: When Z is adjusted, then please adjust S too. When Z is adjusted, then please adjust S too. -0
Wiring diagrams (Control options) With speed controller unit Purpose Set the valve open and close time. Options or 0 potentionmeter, heater M O.LS S.LS CONTROL UNIT / Hz Stop O.LS RL Pot Option S.LS 9 0 earth CL Notes. This diagram shows when the valve is at the intermediate position.. Control unit can be used for each voltage by switching jumper pins, but the motor actuator can not. Notes. Do not use a switch for two or more motor actuators, as the voltage will be transmitted to the other motor through the capacitor and cause malfunction.. Extra limit switches work to % ahead of each opening and closing position of the valve. Therefore, if you stop the valve using signals from an extra limit switch, leakage may occur. Type 0,,. ing degree 0 to 90 degrees and close time Hz Hz Adjustment method 0sec 0sec sec 0sec 00sec 0sec Adjustment trimmer sec 0900sec -
Parts list for with speed controller unit Inside of types 0,, and. Terminal Limit switch cam Dog for open position 0 Dog for closed position Dog for open signal Dog for closed signal 9 9 0 Connector for potentiometer Connector for motor capacitor Connector for motor Trimmer for closed position Trimmer for open position Inside of types and Terminal Limit switch cam Dog for open position Dog for closed position 0 9 9 0 Dog for open signal Dog for closed signal Connector for potentiometer Connector for motor capacitor Connector for motor Trimmer for closed position Trimmer for open position Connector for open signal Connector for closed signal Connector for open limit switch Connector for closed limit switch -
Adjustable operating speed Stroke time for open to close and close to open can be set independently. See the trimmer position for operating speed adjustment. Trimmer position and stroke time Position Type 0, and Type. Type Type Hz Hz Hz Hz Hz Hz Hz Hz sec 0 sec sec 0 sec sec sec 0 sec 0 sec Tolerance ± sec Tolerance ± sec 90 sec 0 sec 0 sec 0 sec sec 0 sec 0 sec sec Tolerance ± 0 sec Tolerance ± 0 sec 0 sec sec sec Tolerance ± 0 sec 0 sec 0 sec 0 sec sec Tolerance ± 0 sec 900 sec sec 00 sec 0 sec 0 sec 0 sec 0 sec 0 sec 00 sec Tolerance ± sec Tolerance ± sec () Carry out the procedure after the limit switch and stopper bolt are set. () Adjust the trimmer with a screwdriver following the table above. () Standard stroke time can be set by turning the trimmer fully in the clockwise direction. () Stroke time can be adjusted by turning the trimmer counterclockwise. Type and : The graph below shows stroke time and trimmer position Type : The graph below shows stroke time and trimmer position HZ HZ HZ HZ 0 0 0 0 0 0 sec 00 00 0 sec -
Rated current Type Motor voltage (V) Impressed voltage (V) Frequency (Hz) Starting current (A) Rated current (A) Note 0. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 means not available as standard specification. Values are provided as reference..... 0. 0. 0. 0. 0. 0..... 0. 0. 0. 0.9 0. 0. 0. 0...........0 0.9 0.9........0.... 0. 0. 0. 0. 0. 0. 0.0 0.0 0. 0. 0.0 0. 0.90 0.0 0.0 0.0 0. 0.0 0.0 0.0 0.0 0.0 0.90.0.00.0 0. 0.0 0. 0.0 0. 0. 0. 0...0.0.0 0.0.00 0.90.00 0.0 0.0 0. 0. -