Greene & Greene Mailbox by Seth Keller Signature details create an elegant box. 2 AmericanWoodworker.com
We needed a new mailbox, but I couldn t find an off-the-shelf version that I liked. So I decided to build my own. As I ve always admired the work of Greene and Greene, the architect brothers who fused Asian design with Arts and Crafts style during the early 20th century, I thought it would be cool to include some of their signature elements in my mailbox: Pronounced joints with heavily rounded edges create the structure, stepped profiles accentuate the lid, and faceted pegs add visual interest and overall balance. The pegs also hide the screws used to assemble the box. I built my box of mahogany a favorite of the brothers Greene and a wood perfectly suited for exterior use. White oak, cyprus or cedar would also be good choices. You ll need 7 bd. ft. of 4/4 stock. Finish your box with exterior oil as I did, or leave it unfinished. Unfinished mahogany turns silver-grey when it s exposed to the elements. Extended box joints The joints may look exotic, but they re really just box joints with extended, rounded-over fingers (Fig. A, page 6). The inside corners of the sockets are also rounded, so they nest perfectly with the rounded fingers. These joints are easy to make with a router and a router table. You ll need two templates, a 1/4-in. roundover bit and a 1/2-in. flushtrim bit with the bearing mounted above the cutting flutes (also called a pattern bit, see Sources, page 5). 1. Make both templates from 1/2-in. MDF (Fig. B). One template is used for the back and front pieces (Parts A and B, Fig. A). The other template is used for the sides (C). The fingers and sockets on these templates must fit together snugly. I cut my templates on the bandsaw, using the miter gauge and the fence to assure straight cuts. 2. Cut the front and back pieces to final dimensions. Then use the front/back template to lay out the fingers and sockets. 3. Cut out the waste between the fingers, using the bandsaw (Photo 1). Don t cut too far into the corners remember, they ll be rounded to fit the fingers. 4. Fasten the template with screws or double-faced tape. If you use screws, mount the templates on the inside face of each piece, so the holes won t show on your completed mailbox. Rout the sockets with a 1/2-in.-dia. flush-trim bit (Photo 2). This leaves a 1/4-in. radius on the inside corners. Later, the fingers will be rounded over at the same radius, so they ll fit perfectly. 5. Cut the sides to final dimension. Use your 12-in. miter saw with the blade swiveled 6 degrees to cut the angled fronts. Attach a stop block to make sure both side pieces are identically cut. If you don t have a large miter saw, you could use a bandsaw to make these cuts and gang the pieces together to sand the edges smooth. 6. Mark, rough-saw and rout fingers and sockets on the side pieces. Carefully position the template to mark the front fingers (Photo 3). Before you rout these narrow pieces, add a board of equal thickness behind, to fully support the template. SOCKET FINGER 1Start by marking and rough-sawing the sockets. Their inside corners will be radiused by routing in a later step, so leave sufficient material. FRONT/BACK TEMPLATE 2Rout the fingers and sockets using templates and a flushtrim bit. This template creates fingers at the top and bottom of the front and back pieces. The fingers and sockets are reversed on the template used to rout the side pieces (below). SIDE TEMPLATE FLUSH ANGLED FLUSH FRONT EDGE 3Carefully position the template on the sides angled front edges. The template s fingers and bottom corner must both be flush. AmericanWoodworker.com 3
4Cut stopped square holes in all the fingers with your mortiser. To assure that the holes are precisely centered, use a clamped-on indexing block to position the workpiece. 5Round the fingers and sockets on a router table. First, hold the piece on edge and rout clockwise around each finger. Then lay the piece flat and rout full length on both faces. STOP BLOCK -WIDE INDEXING BLOCK 1/4" RAD. ROUNDOVER BIT FLAT SECTION 6Cut the top of each side piece at a 45-degree angle for the sloping lid. Leave a 3/4-in.-wide flat section on the top. Clamp on a stop block to assure both pieces are identical. 7. Cut stopped square holes in all the fingers (Photo 4). Make sure to cut the holes on opposite faces of the two sides; otherwise you ll have a pair of left (or right) sides. 8. Drill shank holes for the screws through the stopped mortises. 9. Round the fingers and sockets with a 1/4-in.-rad. roundover bit (Photo 5). When you round the ends of the fingers, rout clockwise and make several shallow passes, to minimize tear out. 10. Dry-fit the front, back and sides to check the fit of the fingers and sockets. Complete the box 11. Cut the sides at a 45-degree angle to accommodate the lid (Photo 6). Use a stop block to guarantee identical parts. 12. Rout end-to-end grooves in the sides and stopped grooves in the front and back pieces for the bottom. Cut the bottom (D) to final dimension, rout a rabbet all around and drill drainage holes. Dry-fit the box with the bottom installed, to make sure it fits. 13. Disassemble the box for sanding. Sand the flat surfaces up to 220-grit with a random orbit sander. Soften the rounded-over edges and ends of the fingers and sockets by hand sanding, so they look organic, rather than machined. 14. Assemble the box (Photo 7). Drill pilot holes to make sure the screws don t break or split the wood. Remember to install the bottom before you fasten the last piece. Make and install the pegs 15. Rip a 2-ft. length of 1/4-in. by 1/4-in. stock. 16. Shape the end to form a pyramid with slightly rounded sides and a dulled point, by rubbing it on 220-grit sandpaper adhered to your bench. Use a handsaw to cut each peg to length. The pegs must be slightly shorter than the mortises, so they don t bottom out. 17. Add a bit of waterproof glue when you insert each peg. Then tap it lightly in place (Photo 8). Immediately remove any squeezed-out glue. Make the top and lid 18. For a good grain match, make the top (E) and lid (F) from the same piece of wood. Rip the top at a 22-1/2-degree angle. Turn the remaining piece over and adjust the fence on the tablesaw to cut the lid. 19. Using the tablesaw, cut a centered 1/4-in. by 1-5/16-in. groove in the front edge of the lid. To make a centered cut, set the blade 3/16-in. from the fence and make two passes rotate the lid 180 degrees to make the second pass. 20. Shape the ends of the top and lid on the router table, using the 1/4-in.-rad. roundover bit. Be careful not to let the bearing disengage when you reach the bevels. 21. Rout mortises for the hinges (see Sources, page 5). The hinges must be positioned slightly lower than normal with the barrels partially hidden so the hinge screws won t break through the angled lid. The mortises are deeper than the hinge leaf thickness, to minimize the gap between the top and lid. You can hand-chop the mortises, or remove 4 AmericanWoodworker.com
most of the material with a straight bit chucked in a laminate trimmer, and then clean up the corners with a chisel. 22. Install the hinges, so you can check the gap and their operation. Brass screws break easily, so drill pilot holes before installing them. Remove the hinges for the next step. 23. Mark the handle profile onto the lid (Fig. D). This stepped profile, with its elongated S-shaped curves, is commonly called a cloud lift. Cut the profile on the bandsaw and smooth the faces by sanding. 24. Plane the spline blank (G) to fit the groove you ve cut in the lid. 25. Install the spline and transfer the cloud lift profile, using a washer with a 1/8-in. rim to create the 3/16-in. lip (Photo 9). 26. Remove the spline, cut the profile on the bandsaw and sand the sawn edge smooth. Install the spline to make sure the profiles are complementary. Then remove the spline again, for final shaping. 27. Round over both edges of the lid s cloud lift profile on the router table, with the 1/4-in.-rad. roundover bit lowered 1/16-in. During this process, the bit s bearing will ride the edge on the opposite side of the groove. 28. Create a half-round edge on the spline s cloud lift profile by sanding or filing, or both. 29. Glue in the spline, using clamps to make sure it seats completely in the groove. 30. Mark and mortise stopped square holes on the lid and top and drill shank holes for screws (in the top, only). 31. Attach the hinges. Center the top/lid assembly on the box and fasten it with screws. Sand the edges of the top and lid while they re attached, to smooth the transition between the two parts. Then remove the lid for final sanding. 32. Install the remaining pegs: two in the top and three in the lid. Final details 33. Apply an exterior grade finish to accentuate the wood s color. Exterior oil finishes are easy to apply, but they must be renewed annually. Spar varnish lasts longer, but it takes longer to apply and must be removed and replaced if it s allowed to deteriorate. 34. Re-attach the lid when the finish is dry. 35. The top and fingers extend beyond the back of the box, so install spacers (J) to facilitate mounting it. Drill mounting holes through the back and the top spacer. Then mount the mailbox with fasteners appropriate for the exterior walls of your house. Sources Rockler, rockler.com, 800-279-4441, Roundover Bit with Bearing, 1/4"radius, 1/2" shank, #91309; Pattern Flush Trim Router Bit, 1/2" diameter, flute length, 1/4" Shank, #80021. Woodcraft, woodcraft.com, 800-225-1153, Drawn Brass Broad Cabinet Hinges, 2" x 1-1/8", #16Q32. Brass wood screws are available at hardware stores and home centers. SQUARE 4x4 #4 x FH BRASS SCREWS 7Assemble the box one corner at a time. Square the joint and clamp the parts firmly. A squarely-milled 4x4 makes this easy. Pre-drill, then install the screws. 8Set the pegs with the tap of a hammer. Use a washer to guarantee they protrude uniformly. SPLINE BLANK 9Use a washer to create a complementary profile when you trace the lid s handle onto the spline blank. The groove for the spline was cut in the lid earlier, before the handle profile was sawn. AmericanWoodworker.com 5
Figure A Exploded View 7/8" 22-1/2 o BEVELS #4 x BRASS F.H. SCREW (TYP.) 11/16" E 3/32" x 9/16" x 2" MORTISE (TYP.) F 1-1/8" x 2" BRASS BUTT HINGE Cutting List Overall Dimensions: 1 H x 15" W x 6" D Part Name Qty. Dimensions A Back 1 5/8" x 10-1/2" x 14-1/2" B Front 1 5/8" x 7-1/2" x 14-1/2" C Side 2 5/8" x 10-1/2" x 5-1/2" D Bottom 1 1/2" x 3-1/8" x 13" E Top 1 5/8" x 2" x 15" F Lid 1 5/8" x 5-7/8" x 15" G Spline 1 1/4" x x 15-1/4" H Peg 21 1/4" x 1/4" x 1/4" J Spacer 2 3/8" x x 10" G ROUNDED EDGE 1/2" MDF Figure B Routing Templates J MOUNTING HOLE C PILOT HOLE FRONT AND BACK (TYP.) SIDES 10-1/2" A C 5" 5" J 1/4" x 5/16" D GROOVE (TYP.) 3/8" D 1/4" x 1/4" TONGUE 3/8" DIA. DRAINAGE HOLE (TYP.) H B Figure C Side Dimensions 5-1/2" 1/4" x 1/4" x 5/16" D MORTISE (TYP.) 1/4" ROUNDOVER (TYP.) 3/4" 45 o 84 o STOPPED MORTISE (TYP.) 3/4" Figure D Lid Dimensions 2" 9/16" 15" 22-1/2 o 11/16" 4-7/8" 5-1/2" 7-1/2" 1/4" x 1-5/16" DADO 1/4" 3/8" RAD. 3/8" RAD. 3/4" 1/2" 1-5/16" 102 o 3/16" LIP 3/16" 1/4" 6 AmericanWoodworker.com