Technical Manual JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A. SPECIFICATIONS ACOUSTIC & ELECTRICAL SPECIFICATIONS: DP3 Internal Amplification Output (at load): 6000W Peak, 3000W Continuous DP3 Output Topology: 3-Channel, Class-I Frequency Response: 45 Hz- 16 khz (±3 db) Frequency Range: 40 Hz- 18 khz (-10 db) Maximum Peak Output 1 : 143 db SPL, 1 m Signal Processing: dbx Type IV Conversion System, 3-Way Precision bandpass filters, limiting, pre-equalization, filers and auto -matic self-tested functions AC Power Operating Range: Auto Select 90-132/VAC 50/60 Hz AC Input Connector: Neutrik Powercon (NAC3MPA) AC Power Loop-thru: Neutrik Powercon (NAC3MPB) AC Current Requirement: 6A per system at 120V, 3A per system at 240V Signal Input: F-LXR Active 20K Ohms Balanced, 10K Ohms Unbalanced Signal Loop-Through: M-XLR (passive pass-through) Controls: Precision 0.5 db increment 16 db input attenuator (DPIP only) SYSTEMS COMPONENTS: Cabinet: Enclosure Assembly C4889ADP Grille: Left (351685-002), Right (351685-001) Low Frequency (2) 2265H, 380 mm (15 ) dia., 76 mm (3 ) Transducer: Dual Coil, Neodymium Differential Drive R, Direct Cooled TM Bandpass Nominal Impedance: 4 Ohms (LF woofers wired in parallel) DC Resistance: 5.10 Ohms ±10% SYSTEMS COMPONENTS: Mid Frequency (4) 2169H, 203 mm (8 in) dia, 76 mm (3 Transducer: in) Dual Coil, Neodymium Differential Drive, Direct Cooled TM Bandpass Nominal Impedance: 8 ohms (drivers wired in series-parallel) DC Resistance: 5.1 Ohms ±10% High Frequency: Transdcuers: (3) 2435H, 76 mm (3 in) diameter beryllium diaprhagm, 38 mm (1.5 in) throad diameter neodymium compression drivers Bandpass Nominal Impedance: 16 Ohms (HF drivers wired in series) DC Resistance: 4.0 Ohms ±10% AURAL SWEEP TEST SPECIFICATIONS: A. System Aural Sweep Test: 100mV Input, 20 Hz to 20 khz Fully clock wise sweep Duration 7 sec B. LF. Aural Sweep Test: 15.0V Input, 10 Hz to 100 Hz C. MF. Aural Sweep Test: 7.0V Input, 20 Hz to 1 khz D. HF. Aural Sweep Test: 0.75V Input, 1 khz to 16 khz PHYSICAL SPECIFICATIONS: Enclosure Dimensions: 494 mm x 1215 mm x 692 mm D (19.4 x 47.8 x 27.2 in. D) Net Weight: 205 lbs. (93.1kg) WARRANTY INFORMATION: Refer to Warranty Statement packed with each product. PACKAGE Warranty 59660 Users Guide 365427-001 Carton 365140-001 Filler, Inner (2) 365141-001 Filler, Outer (2) 365142-001 Microfoam,PGK (8) 49790P Protective Jackets Drive Pack 360849-001 Power Cord Assembly 355040-002 Edison/Shucko,Pack Includes: 355146-001 (120V) (1) 355147-001 (230V) (1) Power Cords NAC3FCB (Neutrik) (1) Gray PowerCon Amp Filler Long (2) 365348-001 Amp Filler Short (2) 365349-001 Front Filler 365347-001 VT4889ADP-ACC Dolly Assembly 229-0029-02 Soft Cover 365110-001 Carton 365243-001 Lower Filler 365244-001 Upper Filler 365245-001 Installation Procedure 365246-001 JBL VT4889-AF Carton 990-00233-00 Filler (2) 991-00258-00 Specification Sheet 336890-001 JBL VT4889-SF Carton 990-00232-00 Filler (2) 337616-001 Specification Sheet 336890-001 910-00035-01 (1) Ferro fluid vial w/ blotter paper and instruction sheet 910-00035-02 (12) Ferro fluid vials w/ blotter paper and instruction sheet 05-12 REV F
WIRING DIAGRAM Compression Driver, HF (3) 2435HPL (125-30001-00X) Diaph Repl D8R2435 BLK BLK YEL YEL/BLK WHT PCB BLU WHT/BLK 1± LF, RIGHT 2± LF, RIGHT 3± MF 4± HF Wire Harness 365111-001 WHT BLU WHT/BLK Driver, Mid Freq. (4) 2169H (339111-001X) Cone Repl C8R2169 GRN GRN/BLK Driver, Low Freq. (2) 2265HPL (338343-003X) Cone Repl C8R2265 RED BLK
SCHEMATIC DIAGRAM Wire Harness P/N 365111-001 Molex: #39-01-2105 Cable Mount
INPUT CUP ASSEMBLY SCHEMATIC Ribbon Cable 352270-001 Connector Assembly Diagram 352087-001 Wire Harness Diagram
COMPONENT EXPLODED VIEW Rigging Bracket (12) 351922-001 881-41100-10 4 x 5/8 PAN,PH,PB,CLR T-Nut (10) 352214-001 10-32 x 1/4 Zinc Plated T-Nut (8) 61861 10-32 X 7/16 Step Barrel Rigging Bracket (4) 351922-001 T-Nut (8) 350840-001 10-32 x 5/16 Gasket, HF Horn Side (2) 359-00237-00 Screw (12) 804-11110-16 10-32 x 1 FLT,PH, BLK ZINC, LCS Bracket HF (2) 339237-001 Horn Support Base 336981-002 Washer (2) 842-00156-03 #8 FLT,SS Nut (2) 834-30010-00 1/4-20 KEPS,BLK,RGT Screw (2) 803-41056-16 8-32 x 1 PAN,PH,SS Input Cup Assembly 352817-001 804-41110-16 10-32 x 1 PAN,PH,BLK Wire Harness 365111-001 Screw (10) 804-41110-16 10-32 x 1 PAN,PH,BLK T-Nut (8) 352214-001 10-32 x 1/4 Zinc Plated Rear Access Panel 365041-001 Gasket, Rear Access Panel 365112-001 910-0006-00 Adh,Jowat, 110 60 BLK 802-11010-10 6-32 x 5/8 FLT,PH,BLK Rigging Bracket (4) 363907-001 Screw (12) 705-90002-14 1/4-20 x 7/8 SCKT SET, CUP POINT Nut (12) 834-30010-00 1/4-20 KEPS,BLK ZINC, LCS, RGT Driver, High Freq. (3) 2435HPL (125-30001-00X) Diaph Repl D8R2435 Rigging Pad (8) 351001-001 1 1/4 Rigging Frame (2) 338978-001 Quick Release Pin (8) 361344-001 338885-001 1/4 x 1 FLTHD, SKT GRD 8 PATCH Horn Support 336980-001 804-42110-12 10 x 3/4 PAN,TORX,BLK ZINC LCS 875-33011-20 1/4-20 x 11/2 SCKT,HEX,BLK ZINC,MCS Amplifier Assembly 354344-014X (DP) 354344-015X (AN) 354344-016X (CN) 354344-017X (DA) (Pleasesee the next page for PWA s part numbers) Gasket, Rear (2) 360-70002-01 15 Driver, Low Freq. (2) 2265HPL (338343-003X) Cone Repl C8R2265 804-72110-24 10-32 x 1 1/2 SKT,TOR,BLK Horn (3) 337055-001 Gasket, HF Horn Center (2) 359-00225-00 Gasket,Waveguide Top/Bot (2) 337119-001 Washer (12) 844-01110-07 1/4, SAE,REG,BLK T-Nut (16) 61861 10-32 x7/16 Step Barrel Grille, Right 351685-001 Grille, Left 351685-002 803-32011-04 8-32 x 1/4 TRUSS,TORX, BLK Grille, HF 128-00430-00 Washer (12) 844-10100-06 #1/4 x.06exttth, REG,CLR ZINC,CS Bolt (12) 854-00003-08 1/4-20 x 1/2 HEX, CLR ZINC,MCAS Wire Jumper (2) 338512-001 Rear Hinge Assembly (2) 364597-001 875-33011-20 1/4-20 x 11/2 SCKT,HEX,BLK ZINC,MCS Grille Trim (2) 351649-001 Handle (2) 354978-001 Gasket,Handle (2) 360937-001 804-421110-12 10-32 x 3/4 PAN,TORX,BLK Screw (12) 884-42110-12 10 x 3/4 PAN,TORX,PB BLK Futr, Coating 910-00015-00 Enclosure Assembly C4889ADP (available to VerTec Dealers and Service Centers only) Driver,Mid Freq. (4) 2169H (339111-001X) Cone Repl C8R2169 Gasket, Rear (4) 360-60002-01 RBI (2) 338020-001 804-72110-24 10-32 x 1 1/2 SKT,TOR,BLK ZINC LCS Handle (8) 923-00022-07 Handle Gasket (8) 382-00337-00 Screw (24) 804-42110-12 10-32 x 3/4 PAN,TORX, BLK Screw (48) 884-42110-12 10 x 3/4 PAN,TORX, PB,BLK Front Hinge Assembly (2) 364596-001 Slider Knob (2) 350839-001 10-32 x 5/8 PATCH R.A.P 354965-001 Dolly Lock Pin (2) 351797-002 Nut (2) 836-36110-00 3/8-24 NYLON,BLK RIGHT Retainer, Dolly Pin (2) 351696-001 R.A.P. 354965-001
AMPLIFIER ASSEMBLY 354344-001 DP3 AMPLIFER ASSEMBLY REFERENCE Amplifier Assemblies Input Modules DP3 Note: Amplifier asembly includes the input module. Part No. Description 354344-001 Amplifier Assembly, Base Model, VT-Series 354344-002X Amplifier Assembly, VT4888DP 354344-003X Amplifier Assembly, VT4882DP 354344-004X Amplifier Assembly, VT4882DP-AN 354344-005X Amplifier Assembly, VT4882DP-CN 354344-007X Amplifier Assembly, VT4888DP-AN 354344-008X Amplifier Assembly, VT4888DP-CN 354344-010X Amplifier Assembly, VT4880ADP 354344-011X Amplifier Assembly, VT4880ADP-AN 354344-012X Amplifier Assembly, VT4880ADP-CN 354344-014X Amplifier Assembly, VT4889ADP 354344-015X Amplifier Assembly, VT4889ADP-AN 354344-016X Amplifier Assembly, VT4889ADP-CN 354344-017X Amplifier Assembly, VT4889ADP-DA 354344-006X Amplifier Assembly, VT4882DP-DA 354344-009X Amplifier Assembly, VT4888DP-DA 354344-013X Amplifier Assembly, VT4880ADP-DA Note: If ordering an input module you must order 1 of the tuning files below depending on the system model number. Model Numbers DP-dbx DP-AN DP-CN DP-DA 361541-001X 361092-001X 361093--001X 444668-001X Tuning File Part Numbers VT4888DP 355059-001 361885-001 361886-001 444729-001 VT4882DP 361282-001 361887-001 361888-001 444728-001 VT4889ADP 365137-001 365113-001 365136-001 444731-001 VT4880ADP 365139-001 365114-001 365138-001 444730-001 354379-001 1/4-20 x 1 1/2, 5/16 SHLDR,BLKLUBE 354379-002 1/4-20 x 3/4, 5/16 SHLDR,BLKLUBE End cap 353901-001 PWA,DP3 Panel 141873-1JBL (Main) PWA, DP3 Output 140193-1JBL NOTE: These (7) individual PWA s are out of the main panel: PWA,DP3 Main 137338-5BJBL PWA, DP3 SMPS 137338-5CJBL PWA,DP3 LVPS 137338-5DJBL PWA,DP3 LF MOD 137338-5EJBL PWA,DP3 MF MOD 137337-5FJBL PWA,DP3 HF MOD 137338-5GJBL PWA,DP3 SPKR INTERFACE 137338-5HJBL Gasket, Cabinet (2) 354341-001 DP3 AMPLIFIER ASSEMBLY REFERENCE AC Module 873-33014-10 8-32 x 5/8 SCKT, CAP DBX, BLK ZINC Gasket, Riser 353830-001 Riser, DP 353829-001 Badge, Center 354382-001 873-33014-10 8-32 x 5/8 SCKT, CAP, DBX, BLK ZINC Riser, DP 353829-001 Module 354446-003 Knob, Volume, Vert 355039-002 (dbx Only) Label, Overlay 354380-002 Gasket, Riser 353830-001 End cap 353901-001 Screen (2) 354290-001 Foam Pad 382-00325-00
DOLLY ASSEMBLY 229-00029-02 JBL VT4889ADP-ACC Dolly Platform 351894-003 Screws (16) 807-13000-20 5/16-18 x 1 1/4 FLT, HEX,CLR ZINC, LCS Insert (10) 816207-001 8-32 x 4MM HXS,KNIFE326D08C10ZC Caster Plate (4) 909-00052-01 T NUT (2) 21749 CP, 832 x 1/4 Caster Wheels (4) 924-00005-00 Nut (16) Nylock Special 352018-001 Screws (12) 803-11000-08 8-32 x 1/2 FLT, PH, CLR ZINC,UNC JBL VT4889ADP-ACC Cover (2) Dolly Housing 351893-001 Spring Assembly (2) Vertec Dolly 351899-001
JBL VT4889-AF Pin, Ball Locking Assembly (2) 361345-001 4 in. DETAIL A Label, Array Frame 955-00154-00 Array Frame 337036-001 VT4889 AF ARRAY FRAME Hinge Block, Front (2) 352963-001 804-31110-08 10-32 x 1/2 TRUSS, PH, BLK ZINC, LCS Hinge Block, Rear (2) 352964-001 DETAIL A Short Long Bolt (16) 856-00013-44 3/8-16 X 2 3/4 HEX,CAP,BLK ZINC,MCA Nut, (16) 836-36113-00 3/8-16 Nylon Lock,BLK ZINC, MCAS,RT Washer, Flat (16) 846-00410-08 3/8 x.08 FLTPL,EX DT, BLK ZINC, CS Specification Tag VT4889 AF 337080-001 VT4889-AF (Array Frame) The VT4889-AF array suspension frame is crafted of 6061 Grade heat-treated aluminum. It includes 11 (eleven) attachment holes for fitting 6.5-ton shackles. Each of these holes is fitted with a bronze bushing for longer life. These holes are set on approximately 102mm (4 ) centers. Each hole has an I.D. (Inner Diameter) of 25.4mm (1 ). The frame includes four receiver blocks, designed to attach Hinge Bars from the VT4889 enclosures. These blocks are made of 7075 Grade aluminum. They are coupled with Grade 8 bolts, and the attached steel quick release pins are secured with stainless steel restraining lanyards. The VT4889-AF weighs 45 kilograms (100 lbs.) It measures approximately 1257mm x 1129mm x 102mm (49.5 x 44.45 x 4 ). VT4889 Manual 336890-001 JBL VT4889-AF
JBL VT4889-SF Pin,Ball Locking Assembly (4) 361345-001 4 in. Hinge Block, Front (2) 352963-001 DETAIL A Label, Array Frame 955-00154-00 Short Frame 888-00106-00 VT4889-SF Bolt (16) 856-00013-40 3/8-16 x 2-1/2 HEX, CAP, BLK ZINC, MCA Nut, (16) 836-36113-00 3/8-16 NYLON LOCK, BLK ZINC, MCAS,RT Washer, Flat (32) 846-00410-08 3/8 x.08 FLTPL,EX DT, BLK ZINC, CS VT4889-SF (Short Frame) Like the larger VT4889-AF, the Short Frame is crafted of 6061 Grade heattreated aluminum. It includes 6 (six) attachment holes. Each hole is fitted with a bronze bushing for longer life. These holes are set on approximately 102mm (4 ) centers. Each hole has an I.D. (Inner Diameter of 25.4mm (1 ). The frame includes four receiver blocks, designed to attach Hinge Bars from the VT4889 enclosures. These blocks are made of 7075 Grade aluminum. They are coupled with Grade 8 bolts, and the attached steel quick release pins are secured with stainless steel restraining lanyards. The VT4889-SF weighs only 23.6 kilograms (52 lbs.). It measures approximately 1257mm x 660mm x 102mm (49.5 x 26 x 4 ). ARRAY FRAME (Short Frame) 804-31110-08 10-32 x 1/2 TRUSS, PH, BLK, ZINC, LCS Hinge Block, Rear (2) 352964-001 DETAIL A Short Long Specification Tag VT4889-SF 337080-001 JBL VT4889-SF