WLL UNIT ssembly uide 150 200 350 400 500 300 450 600 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd
WLL UNIT ssembly uide EORE YOU STRT INSTLLTION SHOULD E PERORMED Y OMPETENT PERSON ONLY. THIS PRODUT OULD E DNEROUS I INORRETLY INSTLLED Panel x1 ack Panel Panel x2 End Panel Panel x2 ase Panel Shelf x2 rontal (packed separately) x1 Hanging racket x2 Inc Screws Hanging racket Plate x2 (Screws NOT included) Hinge Mounting Plate x2 Inc Screws Hinge x2 Inc Screws orner usset x2 Hanging racket over ap x2 () x8 Wooden Dowel () x8 am Dowel (Expanding) (H) x8 am Lock (K) x4 30mm Screw (L) x8 15mm Screw (S) x4 20mm Screw (M) x4 over ap (N) x1 Door uffer (Z) x8 Shelf Peg Plastic (T) x10 ack Panel Support lip REQUIRED TOOLS NOT to be used with M DOWEL & M LOK Page 1 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd
Seat () cam dowel into hole as shown. Step 1. Seat dowel () into holes in end panel () as shown. WLL UNIT ssembly uide Step 2. Seat cam dowel () into holes in end panel () as shown. Step 3. arcase onstruction ttach panels x2 () to panel (), using cam dowels () & cam locks (H) (in blue), and also using dowels () (in orange) in positions as shown. Step 4. Slide panel () into the groove of panels () and x 2 (). Dowel () & am Dowel () location detail N. ll am Locks (H) are to be positioned facing the outside of the unit arcase, for ease of tightening. Do not use power tools with cam dowel () or cam lock (H) H H Step 5. Insert cam lock (H). Hand tighten all cam locks (H), this will expand the cam dowels () and tighten the unit together. View from underside View from underside or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd Page 2
WLL UNIT ssembly uide Step 6. Seat dowel () into holes in both panels () as shown. Seat () cam dowel into hole as shown. Step 7. Seat cam dowel () into holes in both end panels () as shown. Step 8. arcase onstruction ttach panel () to panels () using cam dowels () & cam lock (H) (in blue) and also using dowels () (in orange) in positions as shown. Ensure panel () is seated into the groove of panel (). Dowel () & am Dowel () location detail N. ll am Locks (H) are to be positioned facing the outside of the unit arcase, for ease of tightening. Do not use power tools with cam dowel () or cam lock (H) H H Step 9. Insert cam lock (H). Hand tighten all cam locks (H), this will expand the cam dowels () and tighten the unit together. View from underside View from underside Page 3 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd
Step 10. Ensure arcase is square. WLL UNIT ssembly uide T T 94 126 Step 11. ack panel lips Slide the back panel clips (T) into the groove of both panels () & ()s. The back panel clips (T) should be evenly spaced as shown and positioned to allow the hanging bracket and corner gussets to be fitted. Once in place, tighten screw. Step 12. Hinge Mounting Plates ttach hinge mounting plates onto end panels () in locations shown using 4 x screws (L) Hinge side to be mounted in accordance to customer kitchen plan. 126 94 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd Page 4
WLL UNIT ssembly uide Step 13. Hanging rackets steps a,b & c to be carried out on both sides as shown Detail Detail Detail S S Step a Insert Hanging racket into pre-drilled holes Step b Rotate locking lever 180 degrees Step c Secure with provided 2 x 20mm screws (S) per bracket L L L Detail Step 14. Secure orner ussets to the bottom left and right hand side of the wall unit using 4 x 15mm screws (L) per plate. L Detail View though ack Panel M Step 15. Drill a small pilot hole through the centre of the orner ussets. Use this hole at the end of the process to screw through and into the wall. over the screw heads using the cover caps (M) provided. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used. Pilot hole Page 5 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd
Step 16. Measure appropriately and attach the 2 x hanging bracket plates onto the wall screwing through the provided holes into your wall. Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall construction are used. WLL UNIT ssembly uide Hanging racket Plate Step 17. Hang the cabinet using the brackets to hook onto the plate as shown Step 18. Using points a, b & c adjust the abinet to suit. a Hanging racket viewed though ack Panel Step a. Rotate the screw clockwise to move the cabinet up. nti-clockwise for down. Step b. djust the depth using centre screw. b a b Step c. Screw the red screw until it touches the plate to lock in position. c K Step 19. Screw into any side units using the provided 2x 30mm screws (K) to secure the unit. Screw just to the rear of the hinge plate then place a cover cap on the head to conceal it. or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd Page 6
WLL UNIT ssembly uide Step 20. Insert hinge in top & bottom holes as shown. Hinges Step 21. Secure hinges by tightening 2 x screws with hinge dowels attached. These are already positioned within the hinges. Step 23. djust hinge to suit. s shown below. Step 22. ttach the door to unit where required. To attach door clip hinge onto hinge plate and click to secure. Hinge Mounting Plates RONTL HINE DJUSTMENT To adjust hinge using a screw driver, tighten or loosen as required at points 1 & 2. Point 1 - left - right Point 2 - In - Out Step 24. it cover caps to hinge. Hinge over aps 1 2 Page 7 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd