Assembly Instructons Model: AOGC508FKF FRONT:.52m SIE : 0.78m HEIGHT:.8m CONCRETE SLAB 880 620mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EGES OWNWARS BY 0mm. 50mm 0mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHE We thank you for choosng an Australan Made Avary. For further assstance please vst our detaled nstructonal vdeo lbrary at www.abscosheds.com.au/watch-vdeos At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. feedback@absco.com.au. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE
Model: AOGC508FKF GENERAL INSTRUCTIONS Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the avary must be level. It s recommended that the avary be set on a 00mm concrete slab and anchored down approprately (refer page 5 for detals). Anchor sets are not suppled as standard tems wth ths product. TOOLS REQUIRE 4mm A NOTE ON SAFETY Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. o not erect your avary n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 2
Model: AOGC508FKF COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT ESCRIPTION PART No. CHECK QTY COMPONENT ESCRIPTION PART No. CHECK 2 STEEL SHEET 785mm X 773mm 30A 4 CHANNEL L = 773mm 85 STEEL SHEET 592mm X 773mm 43A 2 CHANNEL L = 773mm 58C 2 STEEL SHEET 785mm X 773mm 30E 5 CHANNEL L = 72mm STEEL SHEET 585mm X 773mm 54R 2 CHANNEL L = 745mm 72 MESH SHEET 220mm X 72mm - 3 JAMB L= 785mm 9 MESH SHEET 590mm X 72mm - JAMB L= 785mm 92 PRE-ASSEMBLE OOR - JAMB L= 72mm 95 2 CHANNEL L = 53mm 64 2 88A LIP TRIM L= 592mm 2 CHANNEL L = 53mm 8F FITTINGS AN ACCESSORIES (SEE NEXT PAGE) INE-A-CHOOK FEEER & RINKER KIT ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 3
Model: AOGC508FKF COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT ESCRIPTION PART No. CHECK QTY COMPONENT ESCRIPTION PART No. CHECK CONTENTS OF FITTINGS PACKET 200 SELF TAPPING SCREWS OOR PABOLT 22A 00 LARGE FLANGE POP-RIVETS OOR PABOLT HASP ASSEMBLY INSTRUCTIONS 6 SMALL FLANGE POP-RIVETS 3mm RILLBIT ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 4
NO. Organc Garden Co. Avary Model: AOGC508FKF 88A 58C PAGE 5 VIEW OF ROOF COMPONENTS 58C 43A 88A ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6
85 64 72 64 9 FRONT OOR PAGE 6 Organc Garden Co. Avary Model: AOGC508FKF 8F 30A 30E 30A 85 30E 85 9 95 92 8F 72 54R VIEW OF WALL COMPONENTS 85 9 ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6
Model: AOGC508FKF ABSCO ASSEMBLY INTROUCTION The snap-tte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. Where possble, many components have been pre-punched for ease of assembly, wth others requrng 3mm holes to be drlled where requred. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIE PUSH HIGH SIE HIGH SIE HIGH SIE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. PUSH Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS HIGH SIE Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed o not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components Pre-drll the hole pror to jonng components together. Many components wll be able to be used as a template to determne drllng locatons Each permeter channel must fnsh flush wth the edges of the sheets. the snap-tte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 3mm POP RIVETS (SMALL FLANGE FOR FITTING OOR HINGES) 3mm POP RIVETS (LARGE FLANGE FOR FITTING MESH TO FRAMES) PAGE 7
Model: AOGC508FKF REAR PANEL ASSEMBLY 30A 30A 8F 8F ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 8
Model: AOGC508FKF ROOF PANEL ASSEMBLY 43A 58C 88A 88A 58C ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 9
Model: AOGC508FKF SIE PANEL ASSEMBLY TWO REQUIRE 72 30E 85 85 ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 0
Model: AOGC508FKF FRONT PANEL ASSEMBLY STEP PARTS REQUIRE: 2) CHANNELS (PART 64) 3) JAMBS (PART 9) 9 64 9 9 64 STEP 2 JOIN ALL SECTIONS TOGETHER, LINING UP EACH JAMB WITH PRE-PUNCHE HOLES LOCATE IN BOTH CHANNEL SECTIONS. 8mm ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE
Model: AOGC508FKF FRONT PANEL ASSEMBLY STEP 3 LOCK THE CHANNEL ON TO THE SHEET AS SHOWN. THE CHANNEL WILL FINISH 30mm IN FROM EACH SIE OF THE SHEET. STEP 4 LAY THESE SECTIONS, ONE AT A TIME, OVER THE FRAME AS SHOWN, LOCKING THE SHEETS INTO THE BOTTOM CHANNEL. STEP 5 MOVE THE OOR HINGE JAMB (PART 92) INTO POSITION, LOCATING IT "OVER THE TOP" OF THE SHEET (54R) AN SECURING IT TO THE OTHER JAMB (9). (THE SCREWS SECURING THE EXISTING JAMB (9) WILL HAVE TO BE REMOVE AN THEN REPLACE) STEP 5 MOVE THE THREE INFILL CHANNELS INTO POSITION AN SCREW TO THE TOP/BOTTOM CHANNELS WITH TWO SCREWS EACH. (CONTINUE) 54 NOTCHE CORNERS TO BOTTOM OF SHEETS 92 THIS EGE ONLY FOLE AT 90 EGREES. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 2
Model: AOGC508FKF OOR PANEL ASSEMBLY (CONTINUE) STEP 7. LAY THE OOR PANEL IN THE OPEN POSITION ON THE FRAME AS SHOWN. USING THE SMALL FLANGE POP RIVETS, SECURE THE OOR TO THE OOR HINGE JAMB. STEP 8. FOR THE MIRAIL ABOVE THE OOR, JOIN THE JAMB (95) TO THE CHANNEL () AS SHOWN. FIT THE MIRAIL PARALLEL ABOVE THE OOR, TO THE SIE JAMBS WITH SCREWS FROM THE UNERNEATH SIE. 95 TO FIT ON TOP OF 92 AN 9 THIS SECTION OF 95 TO BE SLOTTE BEHIN 92 and 9. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 3
Model: AOGC508FKF PANEL CONSTRUCTION SIE WALL PANEL CHANNELS FIT INTO THE NOTCHE FRONT AN REAR WALL PANEL CHANNELS SCREW THE FRONT FRAME CORNER JAMBS INTO THE PRE-PUNCHE HOLES OF THE SIE WALL CORNER MULLIONS. LAP THESE CORNER SHEETS, RILL AN SCREW TOGETHER. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 4
Model: AOGC508FKF FINAL CONSTRUCTION STEP. LINE UP THE PRE-PUNCHE HIOLES IN THE ROOF SHEET AN SIE WALL TOP CHANNELS SECURE WITH SCREWS ANCHORING OF SHE LOCATION OF 8 CONCRETE ANCHORS STEP 2. RILL THROUGH THE ROOF LIP FLASHING, BOTH FRONT AN REAR, INTO THE TOP WALL CHANNELS AN SECURE WITH SCREWS STEP 3. - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, YNABOLT AN STEEL ANGLE - RILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - RILL A 0mm HOLE INTO THE CONCRETE YNABOLT ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 5
Model: AOGC508FKF FITTING OF WIRE MESH ALL MESH SHEETS ARE FITTE TO THE OF THE AVIARY. INSIE WARNING IT IS RECOMMENE THAT NEW GALVANISE MESH SHOUL BE WEATHERE FOR TWO (2) MONTHS OR SCRUBBE WITH A MIL ACIIC SOLUTION SUCH AS VINEGAR, THEN RINSE WITH WATER BEFORE BEING USE IN BIR HOUSING APPLIANCES. INSIE VIEW OF AVIARY THE MESH SHEETS ARE FIXE TO FRAMEWORK USING THE LARGE FLANGE RIVETS SUPPLIE. WORKING FROM INSIE THE AVIARY, LOCATE THE FIRST MESH SHEET OVER THE FRAMEWORK. RILL 3mm HOLES AN FASTEN WITH RIVETS TO THE FRAMEWORK AT 50mm CENTRES. IT IS IMPORTANT TO CONTINUALLY STRETCH THE MESH TO ENSURE A SMOOTH TIGHT FINISH. LOCATE RIVETS AT THE INSIE INTERSECTION OF THE WIRE TO FACILITATE TIGHTENING OF THE MESH AS SHOWN. ORGANIC GAREN CO. ASSEMBLY INSTRUCTION - MOEL: AOGC508FKF 3/0/6 PAGE 6