Bauart gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 00000000 100W Constant Voltage Constant Current LED Driver IP65 IP67 (except for AB,Dtype) Metal housing with class I design Ⅰ current output. HLG100H operates from 90~305VAC and offers models with different rated voltage ranging between V and 54V. Thanks to the high efficiency up to 93%, with the fanless design, the entire series is able to operate for 40 ~ 80 case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG100H is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. I I B I D File Name:HLG100HSPEC 180930
SPECIFICATION MODEL HLG100H HLG100H4 HLG100H30 HLG100H36 HLG100H4 HLG100H48 HLG100H54 DC VOLTAGE CONSTANT CURRENT REGION Note.4 V 10 ~ V 4V 1 ~ 4V 30V 15 ~ 30V 36V 18 ~ 36V 4V 1 ~ 4V 48V 4 ~ 48V 54V 7 ~ 54V RATED CURRENT RATED POWER 4.8A 96W 4A 96W 3.A 96W.65A 95.4W.8A 95.76W A 96W 1.77A 95.58W RIPPLE & NOISE (max.) Note. 150mVpp 150mVpp 0mVpp 0mVpp 0mVpp 0mVpp 0mVpp OUTPUT VOLTAGE ADJ. RANGE Adjustable for A/ABType only (via builtin potentiometer) 17 ~ V ~ 7V 7 ~ 33V 33 ~ 40V 38 ~ 46V 43 ~ 53V 49 ~ 58V CURRENT ADJ. RANGE Adjustable for A/ABType only (via builtin potentiometer) 3 ~ 4.8A.5 ~ 4A ~ 3.A 1.65 ~.65A 1.4 ~.8A 1.5 ~ A 1.1 ~ 1.77A VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% ±1.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME Note.6 10ms,50ms/115VAC 500ms,50ms/30VAC HOLD UP TIME (Typ.) 16ms / 115VAC, 30VAC VOLTAGE RANGE Note.5 90 ~ 305VAC 17 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF 0.98/115VAC, PF 0.95/30VAC, PF 0.93/77VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< % (@ load 60% / 115VAC,30VAC; @ load 75% / 77VAC) TOTAL HARMONIC DISTORTION INPUT (Please refer to " TOTAL HARMONIC DISTORTION (THD)" section) EFFICIENCY (Typ.) AC CURRENT (Typ.) 93% 1.A / 115VAC 93% 0.55A / 30VAC 93% 0.5A / 77VAC 93% 93% 93% 93% INRUSH CURRENT (Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 60A(t width=415 μs measured at 50% I peak ) at 30VAC; Per NEMA 410 4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 30VAC LEAKAGE CURRENT <0.75mA / 77VAC OVER CURRENT 95 ~ 106% Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION 3 ~ 7V 8 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V OVER VOLTAGE Shut down o/p voltage with autorecovery or repower on to recovery 54 ~ 63V 59 ~ 65V OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase= 40 ~ 80 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase= 80 ENVIRONMENT WORKING HUMIDITY ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ 60 ) 10 ~ 500Hz, 5G 1min./1cycle, period for 7min. each along X, Y, Z axes UL8750 (type HL ), CSA C. No. 50.008; EN/AS/NZS 613471, EN/AS/NZS 6134713 independent; SAFETY STANDARDS Note.8 GB19510.1,GB19510.14, IP65 or IP67, J613471, J6134713, KC KN61347 1, KN6134713(except for AB,Dtype), EAC TP TC 004 approved ; design refer to UL609501, TUV EN609501 SAFETY & WITHSTAND VOLTAGE I/PO/P:3.75KVAC I/PFG:KVAC O/PFG:1.5KVAC EMC ISOLATION RESISTANCE I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 5 / 70% RH EMC EMISSION Note.8 Compliance to EN55015, EN5503 Class B, EN610003 Class C (@ load 60% ) ; EN6100033,GB17743 and GB1765.1, EAC TP TC 0 EMC IMMUNITY Compliance to EN610004,3,4,5,6,8,11, EN61547, EN5504, light industry level ( surge immunity LineEarth 4KV, LineLine KV ), EAC TP TC 0 OTHERS NOTE MTBF 19.K hrs min. MILHDBK17F (5 ) DIMENSION *68*38.8mm (L*W*H) PACKING 1.1Kg; 1pcs/14.4Kg/0.8CUFT File Name:HLG100HSPEC 180930
BLOCK DIAGRAM Fosc : 100KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. V V DIM DIM (B Type) DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io (%) Typical output current normalized by rated current (%) File Name:HLG100HSPEC 180930
DIMMING OPERATION HLG100H DIM(Blue) DIM(White) V(Black) V(Red) 3 in 1 dimming function (for B/ABType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 1V V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% DO NOT connect "DIM to V" % 10% 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLG100HSPEC 180930
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Swih Adjuster 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG100H BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a swih and relay can turn ON/OFF the lighting fixture. File Name:HLG100HSPEC 180930
OUTPUT LOAD vs TEMPERATURE(Note.10) 100 100 80 80 60 60 LOAD (%) 40 LOAD (%) 40 40 5 10 0 15 30 50 60 70 (HORIZONTAL) 40 5 0 45 55 65 75 80 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 80 Constant Current Mode LOAD (%) 100 90 80 70 60 50 40 PF 1.00 0.98 0.96 0.94 0.9 0.90 0.88 0.86 0.84 0.8 0.80 0.78 77Vac 30Vac 115Vac 90 100 15 135 145 155 165 175 180 0 30 305 50% 60% 70% 80% 90% 100% INPUT VOLTAGE (V) 60Hz LOAD (100W) Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 80 5 EFFICIENCY vs LOAD possess superior working efficiency that up to 93% can be reached in field applications. 48V Model, Tcase at 80 94 90 86 THD(%) 15 10 5 115VAC 30VAC 77VAC EFFICIENCY (%) 8 78 74 70 66 77Vac 30Vac 115Vac 6 0 58 50% 60% 70% 80% 90% 100% 10% % 30% 40% 50% 60% 70% 80% 90% 100% LOAD LOAD File Name:HLG100HSPEC 180930
LIFE TIME 1 100 80 LIFETIME(Kh) 60 40 0 30 40 50 60 70 80 90 Tcas e ( ) File Name:HLG100HSPEC 180930
MECHANICAL SPECIFICATION Blank/DType Case No.994A Unit:mm 1 9.6 196 AType 1 9.6 9.4 Tcase 98 V(Black) SJOW 17AWG&H05RNF 1.0mm *3C V(Red) SJOW 17AWG&05RNF 1.0mm *C ψ 4. 4PL SJOW 17AWG&H05RNF 1.0mm *3C 9.4 34. 9.4 9.4 34. 68 : Max. Case Temperature 68 34 196 Tcase Vo ADJ. 98 Io ADJ. SJOW 17AWG&05RNF 1.0mm *C ψ 4. 4PL 38.8 : Max. Case Temperature 38.8 34 V(Black) V(Red) File Name:HLG100HSPEC 180930
BType 1 196 SJOW 17AWG&H05RNF 1.0mm *3C 9.6 9.4 34. 9.4 68 Tcase 34 98 ψ 4. 4PL UL517 AWG*C SJOW 17AWG&05RNF 1.0mm *C DIM(Blue) DIM(White) V(Black) V(Red) : Max. Case Temperature ABType 1 196 9.6 Tcase Vo ADJ. 98 Io ADJ. : Max. Case Temperature 38.8 38.8 SJOW 17AWG&H05RNF 1.0mm *3C 9.4 34. 9.4 68 34 ψ 4. 4PL UL517 AWG*C SJOW 17AWG&05RNF 1.0mm *C DIM(Blue) DIM(White) V(Black) V(Red) File Name:HLG100HSPEC 180930
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG100H to operate in dry/wet/damp or outdoor environment. AC source I/P HLG100H O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M1 Order No. Suitable Current 4PIN 5A/PIN M104 10A max. 5PIN 5A/PIN M105 10A max. M15 Order No. Suitable Current PIN 1A/PIN M150 1A max. LED Lamp Cable Joiner 66 6 CJ041 suitable for 14AWG~16AWG CJ04 suitable for 18AWG~AWG ψ5 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG100H O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ04. Junction Box Option 196 358 76 10 5 SJOW 17AWG& H05RNF 1.0mm *3C 68 61 8.5 3 8.5 6 ψ5 V(Black) V(Red) SJOW 17AWG& 05RNF 1.0mm *C 3 PF 1/" 3 PF 1/" 150± 35 38.8 150± Junction box option is available for A / Blank Type. Please contact MEAW WELL for details. 86 INSTALLATION MANUAL Please refer to:http://www.meanwell.com/manual.html File Name:HLG100HSPEC 180930