CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 1 Monday, November 7, 2011 3:48 PM FOLDING MITRE SAW STAND MODEL NO: CFMSS1 PART NO: 6500968 OPERATION & MAINTENANCE INSTRUCTIONS LS1111
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 2 Monday, November 7, 2011 3:48 PM INTRODUCTION Thank you for purchasing this CLARKE folding mitre saw stand. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. SPECIFICATIONS Model Number CFMSS1 Part Number 6500968 Max. Load Maximum Dimensions (W x H x D) (stops in place) Minimum Dimensions (W x H x D) Distance (between rollers, centre to centre) Weight 100 kg 2145 mm x 1015 mm x 635 mm 1435 mm x 880 mm x 635 mm Min. 1150 mm - Max 2000 mm 13 kg 2
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 3 Monday, November 7, 2011 3:48 PM SAFETY WARNINGS 1. The maximum capacity of this mitre saw stand is 100 kgs. On no account must this be exceeded. 2. Do not climb on the mitre saw stand or use as a step ladder, as this could cause severe damage. 3. Take care when placing a load on to the mitre saw stand, It should be placed gently so that the strain is taken up gradually. 4. Always check the mitre saw stand for wear, damage or loose parts before use. 5. Always ensure you are working on a firm flat surface, and that the mitre saw stand is completely stable. Read instruction manual before use. CARTON CONTENTS The following items should be supplied in the carton. If any parts are missing or damaged, please see your Clarke dealer where you purchased the mitre saw stand. Description Part Number 1 x Base assembly HTCFMSS101 2 x Work support (Roller) HTCFMSS102 2 x Saw mounting bracket HTCFMSS103 4 x Length adjustment knob HTCFMSS104 2 x Height locking knob HTCFMSS105 4 x Truss head M6x60 Carriage Bolt (55mm threaded) HTCFMSS106 4 x M6 nut HTCFMSS107 4 x M6 Flat washer HTCFMSS108 4 x M6 Spring Washer HTCFMSS109 3
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 4 Monday, November 7, 2011 3:48 PM ASSEMBLY IMPORTANT: Always ensure that before mounting a Mitre Saw, you take into consideration the type of cuts and the size of the workpiece you will be working with. Stability of the table is of paramount importance. Take extra care if working with large or very long pieces, extra support may be required. SETTING UP THE MITRE SAW STAND 1. Press the locking pin inwards and rotate each leg into position. The locking pin will locate into a second hole when secure. 2. Repeat for all four legs. 3. Slide a roller into each end of the frame. 4. Adjust the roller to the desired height and secure with a height locking knob. Ensure the roller is inserted as shown noting the position of the stop bar. 5. Place the mounting brackets on the frame but do not tighten the clamps. 4
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 5 Monday, November 7, 2011 3:48 PM 6. Place the mitre saw onto the two mounting brackets and slide the carriage bolts from beneath the bracket and through the holes in the base of the mitre saw. The flat washer / spring washer and nuts are then used to secure the mitre saw. NOTE: If your mitre saw does not have suitable holes for mounting to this stand, it should be mounted on to a suitable board at least 15 mm thick, and the board, with mitre saw, secured to this stand using suitable bolts. 7. Finally, tighten the tool support clamps using the handles. NOTE: Check before use that the range of motion on the mitre saw is not restricted in any way by the carriage bolts. if it is mount the mire saw on to a suitable board of at least 15 mm thick as mentioned previously. ROLLERS AND WORKSTOPS You can flip the work stops located on the rollers into position to provide you with a positive stop. The rollers together with the work stops may be extended as required. 1. Loosen the length adjustment knob. 2. Adjust to the required position. 3. Retighten the length adjustment knob. 5
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 6 Monday, November 7, 2011 3:48 PM WOODWORKING TOOLS AND ACCESSORIES A huge range of Clarke woodworking tools and accessories are available from your local Clarke stockist. Including: Replacment mitre saw blades Scroll Saws Circular Saws Band Saws Jig Saws Table Saws Lathes Sanders Routers Planers Thicknessers Work Clamps Work Benches 6
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 7 Monday, November 7, 2011 3:48 PM 7
CFMSS1 Folding Mitre Saw Stand (080602-1).fm Page 8 Monday, November 7, 2011 3:48 PM