THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 50040 BLACK/MAPLE, 50042 PEWTER/CHERRY IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com OR CALL OR WRITE THE FOLLOWING: 8700 REX ROAD PICO RIVERA, CA 90660 (562) 446-2255 FAX (562) 446-2277 (800) 445-1527 6/2/04
ASSEMBLY INSTRUCTIONS IMPORTANT: CAREFULLY UNPACK & IDENTIFY EACH COMPONENT BEFORE ATTEMPTING TO ASSEMBLE. REFER TO PARTS LIST. PLEASE TAKE CARE WHEN ASSEMBLING THE UNIT AND ALWAYS SET THE TABLE TOPS ON A CLEAN, SOFT SURFACE. NOTE: DO NOT TIGHTEN SCREWS. 6 22 7 10 8 8 1 1. LAY DESKTOP (1) ON A SMOOTH, FLAT SURFACE WITH HOLES FACING UP. ATTACH LEFT AND RIGHT REAR LEGS (6 AND 7) TO DESKTOP (1) USING PHILLIPS SCREWS (). (LEAVE SCREWS LOOSE AND MAKE SURE 2 SMALL HOLES IN LEGS FACE REAR) ATTACH FRONT LEGS (8) TO DESKTOP USING PHILLIPS SCREWS (). (LEAVE SCREWS LOOSE AND MAKE SURE 2 SMALL HOLES IN LEGS FACE REAR) INSERT END OF CURVED TUBES (10) INTO HOLES IN REAR LEGS AND ATTACH USING ALLEN BOLTS (22).
16 22 22 22 26 9 22 22 1 12 12 2. ATTACH REAR PANEL (9) TO REAR LEGS USING WASHERS (26) AND ALLEN BOLTS (22). INSERT CORD MANAGEMENT CLIP (16) INTO REAR PANEL AS SHOWN. ATTACH KEYBOARD SLIDERS (12) TO DESKTOP (1) USING ALLEN BOLTS (22).
21 21 15 14 14 2 4 3. PLACE BOTTOM SHELF (2) (HOLES FACE UP) ONTO LEGS AND ATTACH USING ALLEN BOLTS (21). ATTACH LOCKING CASTERS (14) TO FRONT OF BOTTOM SHELF USING PHILLIPS SCREWS (). ATTACH NON-LOCKING CASTERS (15) TO REAR OF BOTTOM SHELF USING PHILLIPS SCREWS (). PLACE KEYBOARD SHELF (4) UNDER TABS ON KEYBOARD SLIDERS AND ATTACH USING PHILLIPS SCREWS (). TIGHTEN ALL SCREWS IN LEGS FROM STEP 1.
5 5 22 11 11 13 13 22 26 26 20 20 4. CAREFULLY TURN UNIT RIGHT SIDE UP. ATTACH VERTICAL PANELS (5) TO DESK TOP USING ALLEN SCREWS (20). ATTACH BRACKETS (13) TO THE SIDES OF VERTICAL PANELS (5) USING PHILLIPS SCREWS (). ATTACH CD HOLDERS (11) TO DESK TOP USING WASHERS (26) AND ALLEN BOLTS (22). ATTACH OTHER END OF CURVED TUBES (WITH TAB) TO FRONT LEGS (8) USING PHILLIPS SCREWS ().
3 18 18 19 17 26 26 22 22 24 24 5. SCREW CAM BOLTS (18) INTO BOTTOM OF TOP SHELF (3). LAY TOP SHELF ONTO VERTICAL PANELS MAKING SURE HOLES IN VERTICAL PANELS AND CAM BOLTS ALIGN. INSERT CAM LOCKS (19) INTO HOLES IN VERTICAL PANELS MAKING SURE ARROW POINTS TOWARDS BOLTS. SCREW CAM LOCKS 1/4 TURN OR UNTIL SECURE TO LOCK IN PLACE. SCREW PHILLIPS BOLTS WITH WASHERS (24) INTO HOLES IN BRACKETS. ATTACH CD HOLDERS TO TOP SHELF USING WASHERS (26) AND ALLEN BOLTS (22).
DESCRIPTION PARTS LIST QUANTITY 1. DESKTOP 1 2. BOTTOM SHELF 1 3. TOP SHELF 1 4. KEYBOARD SHELF 1 5. HORIZONTAL PANEL - 1 LEFT AND 1 RIGHT 2 6. REAR LEG - LEFT 1 7. REAR LEG - RIGHT 1 8. FRONT LEG 2 9. REAR PANEL 1
DESCRIPTION PARTS LIST QUANTITY 10. CURVED TUBE 4 11. CD HOLDER 2 12. KEYBOARD SLIDER 1 SET 13. BRACKET 2 14. CASTER - LOCKING 2 15. CASTER - NON-LOCKING 3 16. CORD MANAGEMENT CLIP 1 17. CORD MANAGEMENT CAP 1 18. CAM BOLT 4 19. CAM LOCK 4
DESCRIPTION PARTS LIST QUANTITY 20. ALLEN SCREW - 1/4 X 2 4 21. ALLEN BOLT - M8 X 2 4 22. ALLEN BOLT - 1/4 X 1/2 16. PHILLIPS SCREW 48 24. PHILLIPS BOLT WITH WASHER 20 25. ALLEN WRENCH 2 26. WASHER 8 0 1 2 3 4 5 6 7 LIMITED WARRANTY Studio RTA warrants to the Original Purchaser that this product will be free from defects in its material and workmanship as described below. The company will repair or replace, at its option, without charge to the original purchaser only, defective products or parts during the following warranty periods. Ten (10) years or (Thirty (30) days on closeouts and discounted products) while owned by the Original Purchaser... Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty shall be effective for the applicable time period beginning from date of purchase as shown on your original sales receipt. This warranty is your sole remedy for product defects and excludes defects due to or arising in connection with product abuse or misuse, use modification of, or attachments to the product, and products or parts not used, maintained, or installed in accordance with the company s installation, maintenance and/or applicable guidelines. There are no other warranties, express or implied other than those specifically described, including without limitation any implied warranty of merchantability or of fitness for a particular purpose. The company will not be responsible for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.the company will advise you of the procedure to follow in making warranty claims.telephone Studio RTA at (562) 446-2255 to explain the defect and give your name, address, and telephone number. Please be prepared with the model number of the product, date and place of purchase. If you require any assistance with assembly or parts please visit our website: www.studiorta.com.