SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z540-1-1994 FUGRO SUHAIMI LIMITED, YANBU P.O. Box 31720 Yanbu Al-Sinaiyah-41912, Kingdom of Saudi Arabia Mohammed Baquer Hameed Phone: 009663 857 2035 CALIBRATION Valid To: December 31, 2018 Certificate Number: 3512.10 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations 1 : I. Dimensional Parameter/Equipment Range CMC 2 ( ) Comments Calipers (All Types) (10 to 300) mm (300 to 600) mm 8.8 µm 8.8 µm Kudale caliper checker Micrometers (Inside, Outside & Depth) Up to 25 mm (25 to 200) mm (200 to 300) mm (300 to 500) mm 8.6 µm 8.8 µm 8.8 µm 8.8 µm Mititoyo gauge block Dial Indicators Up to 25 mm 8.4 µm Kudale dial calibration tester Measuring Tape/Steel Rule Up to 1000 mm 0.82 mm Kudale scale & tape Height Gauge (10 to 600) mm 6.8 µm Kudale caliper checker Page 1 of 12
Parameter/Equipment Range CMC 2 ( ) Comments Digital Thickness Gauge, Ferrous (25.4 to 1899) µm 1.0 µm Elcometer thickness foils set Thickness Gauge, Dial Type Up to 1 mm Up to 100 mm 1.1 µm 5.8 µm Mitutoyo gauge block set & foils Set II. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 4 ( ) Comments DC Resistance Generate, Earth Test Insulation & Continuity Tester (1 to 10) Ω (10 to 100) Ω (0.1 to 1) kω (1 to 10) kω (10 to 100) kω (0.1 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ Up to 1 GΩ (1 to 10) GΩ (10 to 100) GΩ 0.01 % + 1.2 Ω 0.01 % + 1.2 Ω 0.01 % + 1.2 kω 0.01 % + 1.2 kω 0.01 % + 1.2 kω 0.01 % + 1.2 MΩ 0.03 % + 1.2 MΩ 0.03 % + 1.2 MΩ 0.04 % + 0.16 GΩ 0.03 % + 1.2 GΩ 0.05 % + 1.2 GΩ ILET decade resistance box DC Voltage (8845A) Measure (0 to 100) mv (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V 0.006 % + 0.003 mv 0.005 % + 0.1 mv 0.004 % + 0.2 mv 0.005 % + 2.4 mv 0.005 % + 23 mv Fluke 8845A precision multimeter Page 2 of 12
Parameter/Equipment Range CMC 2, 3, 4 ( ) Comments AC Voltage Measure (0 to 100) mv 45 Hz 100 khz 200 khz 0.07 % + 0.024 mv 0.07 % + 0.024 mv 0.14 % + 0.05 mv 0.7 % + 0.12 mv 4.6 % + 0.03 mv Fluke 8845A precision multimeter (0 to 1) V (Up to 50) Hz (0.05 to (10 to 30) khz (30 to 100) khz (100 to 200) khz 0.1 % + 0.4 mv 0.1 % + 4.0 mv 0.1 % + 1 mv 0.07 % + 1 mv 4.6 % + 7 mv (1 to 10) V (0.05 to 10) khz (10 to 30) khz (30 to 100) khz 0.07 % + 0.4 mv 0.07 % + 0.4 mv 0.14 % + 4 mv 0.7 % + 11 mv (10 to 100) V (0.05 to 10) khz (10 to 30) khz (30 to 100) khz 0.07 % + 20 mv 0.07 % + 30 mv 0.14 % + 40 mv 0.7 % + 0.27 V (100 to 700) V (0.05 to 1) khz (1 to 10) khz 0.07 % + 0.25 V 0.07 % + 0.21 V 0.07 % + 0.25 V Resistance Measure (0 to 100) Ω (0.1 to 1) kω (1 to 10) kω (10 to 100) kω (0 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ 0.01 % + 0.005 Ω 0.01 % + 0.1 Ω 0.01 % + 0.1 Ω 0.01 % + 4 Ω 0.01 % + 0.04 kω 0.05 % + 1.6 kω 0.9 % + 61 kω Fluke 8845A precision multimeter DC Current Measure (0 to 100) µa (0 to 1) ma (1 to 10) ma (10 to 100) ma (0.1 to 1) A (1 to 3 ) A (1 to 10) A 0.1 % + 0.04 µa 0.06 % + 0.2 µa 0.06 % + 1.0 µa 0.002 % + 0.013 ma 0.06 % + 0.3 ma 0.12 % + 1.0 ma 0.17 % + 6.0 ma Fluke 8845A precision multimeter Page 3 of 12
Parameter/Equipment Range CMC 2, 4 ( ) Comments AC Current Measure (0 to 10) ma (0.05 to 1) khz (1 to 10) khz 0.17 % + 7 µa 0.17 % + 7 µa 0.4 % + 8 µa Fluke 8845A precision multimeter (10 to 100) ma (0.05 to 1) khz (1 to 10) khz 0.12 % + 65 µa 0.12 % + 65 µa 0.23 % + 0.32 ma (0.1 to 1) A (0.05 to 1) khz (1 to 10) khz 0.1 % + 0.8 ma 0.12 % + 0.8 ma 0.4 % + 9 ma (1 to 3) A (0.05 to 1) khz (1 to 10) khz 0.2 %+ 2 ma 0.2 %+ 2 ma 0.4 % + 11 ma (3 to 10) A (0.05 to 1) khz 0.2 % + 9 ma 0.2 % + 1.3 ma Welding Machine Measure, Volt & Ampere (20 to 80) Vdc (10 to 500) Adc (20 to 80) Vac (10 to 500) Aac 0.09 Vdc 1.5 Adc 0.11 Vac 2.1 Aac SMP welding machine SMP 1336 Sr. No.56-208 DC High Voltage Holiday Detector - Measure (0 to 2) kv (2 to 20) kv (20 to 60) kv 0.06 % + 1.2 kv 0.06 % + 1.2 kv 0.06 % + 1.2 kv Brandenburg DC HV tester Multimeter, Clamp Meter DC-Voltage Test Generate (0 to 320) mv (0.32 to 3.2) V (3.3 to 32) V (32 to 320) V 100 V to 1 kv 0.01 % + 13 µv 0.01 % + 120 mv 0.01 % + 1.4 mv 0.01 % + 14 mv 0.03 % + 120 mv Page 4 of 12
Parameter/Equipment Range CMC 2, 4 ( ) Comments AC Voltage Generate (0 to 0.3) V 1 khz 50 khz 100 khz 0.05 % + 43 µv 0.05 % + 43 µv 0.05 % + 43 µv 0.05 % + 47 µv 0.07 % + 80 µv 0.10 % + 150 µv 0.02 % + 370 µv (0.3 to 3) V 1 khz 50 khz 100 khz 0.05 % + 410 µv 0.05 % + 430 µv 0.05 % + 430 µv 0.05 % + 470 µv 0.01 % + 1 mv 0.2 % + 4 mv (3 to 30) V 1 khz 50 khz 100 khz 0.05 % + 4 mv 0.05 % + 4 mv 0.05 % + 4 mv 0.1 % + 5 mv 0.2 % + 18 mv 0.4 % + 50 mv (30 to 100) V 1 khz 50 khz 100 khz 0.05 % + 18 mv 0.05 % + 19 mv 0.05 % + 18 mv 0.1 % + 22 mv 0.1 % + 32 mv 0.2 % + 59 mv 0.4 % + 170 mv (100 to 300) V 0.06 % + 49 mv 0.06 % + 69 mv 0.09 % + 79 mv 0.17 % + 150 mv (300 to 750) V 200 Hz 0.07 % + 140 mv 0.07 % + 140 mv 0.10 % + 220 mv 0.10 % + 240 mv 0.18 % + 320 mv Page 5 of 12
Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Current Measure and Generate 200 A 500 A 50 Hz 0.64 % + 0.8 A 0.64 % + 1.7 A with coil 5500A Parameter/Equipment Range CMC 2, 3, 4 ( ) Comments DC Current Generate (0 to 0.3) ma (0.3 to 3.2) ma (3.2 to 32) ma (32 to 320) ma (0.32 to 3.2) A (3.2 to 10) A 0.02 % + 22 na 0.02 % + 200 na 0.02 % + 2 µa 0.02 % + 22 µa 0.07 % + 0.51 ma 0.06 % + 2.3 ma Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Current Generate (0 to 0.3) ma 10 Hz 110 Hz 0.08 % + 0.4 µa 0.08 % + 0.4 µa 0.08 % + 0.7 µa 0.08 % + 0.4 µa 0.34 % + 12 µa 0.3 % + 12 µa with coil 5500A (0.3 to 3) ma 10 Hz 110 Hz 0.08 % + 0.6 µa 0.08 % + 0.6 µa 0.08 % + 0.6 µa 0.08 % + 0.6 µa 0.12 % + 0.9µA 0.31 % + 3 µa Page 6 of 12
Parameter/Range Frequency CMC 2, 3, 4 ( ) Comments AC Current Generate (cont) (3 to 30) ma 10 Hz 110 Hz 0.1 % + 4 µa 0.08 % + 7 µa 0.08 % + 7 µa 0.08 % + 7 µa 0.12 % + 12 µa 0.29 % + 36 µa with coil 5500A (30 to 300) ma 10 Hz 110 Hz 0.09 % + 78 µa 0.09 % + 69 µa 0.09 % + 69 µa 0.09 % + 69 µa 0.12 % + 100 µa 0.29 % + 240 µa AC Current Generate (0.3 to 3) A 110 Hz 0.12 % + 1 ma 0.12 % + 1 ma 0.12 % + 1 ma 0.29 % + 4 ma (3 to 10) A 110 Hz 0.23 % + 7 ma 0.23 % + 7 ma 0.23 % + 7 ma 0.58 % + 19 ma Page 7 of 12
Parameter/Equipment Range CMC 2, 3, 4 ( ) Comments Resistance Generate (0 to 10) Ω (10 to 40) Ω (40 to 400) Ω 400 Ω to 1 kω (1 to 4) kω (4 to 40) kω (40 to 400) kω 400 kω to 1 MΩ (1 to 4) mω (4 to 40) mω (40 to 100) mω 0.030 % + 12 mω 0.030 % + 14 mω 0.024 % + 45 mω 0.017 % + 160 mω 0.017 % + 400 mω 0.023 % + 4.3 Ω 0.025 % + 15 Ω 0.023 % + 180 Ω 0.023 % + 0.55 Ω 0.058 % + 20 kω 0.069 % + 54 kω Capacitance Generate (0 to 0.75) nf (0.75 to 3) nf (3 to 6) nf (6 to 600) nf 0.35 % + 18 pf 0.35 % + 220 pf 0.35 % + 38 pf 1.1 % + 2.4 nf Transmitter & Switch -20 C 50 C 150 C 650 C 0.10 C 0.11 C 0.10 C 1.3 C Temperature dry block & precision multimeter III. Mechanical Parameter/Equipment Range CMC 2 ( ) Comments Pressure Gauge, Pressure Recorder, Pressure Switch, Pressure Transmitter, Pressure Relief Valve 5 bar 10 bar 20 bar 30 bar 40 bar 50 bar 60 bar 100 bar 200 bar 400 bar 600 bar 800 bar 1000 bar 1200 bar 0.01 bar 0.01 bar 0.01 bar 0.01 bar 0.02 bar 0.02 bar 0.02 bar 0.44 bar 0.82 bar 1.7 bar 3.8 bar 8.2 bar 8.2 bar 8.2 bar DH Budenberg (580 series), dead weight tester (hydraulic) Page 8 of 12
Parameter/Equipment Range CMC 2 ( ) Comments Vacuum Gauge (0 to 1) bar 0.016 bar Wika standard vacuum gauge Weighing Scales of Concrete Batch Plant Asphalt Batch Plant 600 kg 0.68 kg Cast iron & standard weights Mass Fixed Points 1 mg 2 mg 5 mg 10 mg 20 mg 50 mg 100 mg 200 mg 500 mg 0.05 mg 0.11 mg 0.06 mg 0.06 mg 0.06 mg 0.06 mg 0.10 mg 0.08 mg 0.14 mg Analytical balance Radwag model AS60/220.R2 Sr. No.413123 /56-189 1 g 2 g 5 g 10 g 20 g 50 g 100 g 200 g 500 g 1000 g 2000 g 5000 g 10 kg 20 kg 0.05 mg 0.085 mg 0.056 mg 0.050 mg 0.053 mg 0.060 mg 0.073 mg 0.22 mg 27 mg 27 mg 27 mg 69 mg 37 mg 36 mg Mettler Toledo mass comparator & analytical balance Radwag model AS60/220.R2 Sr. No.413123 /56-189 Weighing Scales (1 to 200) g (5 to 5000) g Up to 15 kg Up to 20 kg Up to 30 kg Up to 60 kg Up to 100 kg 5.3 mg 0.06 g 0.75 g 0.84 g 0.90 g 17 g 0.05 kg Standard weights Compression Machine (0 to 2000) kn 0.74 % Matest load cell, digital indicator Page 9 of 12
Parameter/Equipment Range CMC 2,3 ( ) Comments Torque Wrench Low Range 10 Nm (10 to 50) Nm (50 to 100) Nm (100 to 300) Nm (300 to 500) Nm 0.60 Nm 0.60 Nm 0.71 Nm 1.2 Nm 1.5 Nm Kkudale torque tester High Range (500 to 700) Nm (700 to 1000) Nm (1000 to 2000) Nm (2000 to 3000) Nm 15 Nm 16 Nm 12 Nm 14 Nm Torque wrench tester Dongguan Liyi Environment Technology Sr. No. 56-188 ANJ-5000 Proving Ring 45 kn 0.40 kn Bonghin load cell IV. Thermodynamics Parameter/Equipment Range CMC 2 ( ) Comments Thermometer -20 C 50 C 150 C 650 C 1100 C 0.10 C 0.11 C 0.11 C 1.3 C 0.77 C Isotech & Fluke dry block Wika dry block CTD 9100-1100 (1100 C) Infrared Thermometer (0 to 50) C (50 to 100) C (100 to 200) C (200 to 300) C (300 to 400) C (400 to 500) C 0.11 C 0.10 C 0.10 C 0.16 C 0.09 C 0.17 C Precision infrared Fluke model-4181 Sr. No. 56-159-1 Page 10 of 12
Parameter/Equipment Range CMC 2 ( ) Comments Oven & Furnace (0 to 400) C (0 to 1200) C 0.1 C 3.0 C Fluke digital thermometer Temperature Recorder 100 C 1000 C 1.4 C 7.3 C Fluke process Temperature Bath 60 C 0.06 C Fluke digital thermometer 1523 Temperature & Humidity 10 C to 40 C (36 to 76) % RH 0.21 C 0.55 % RH Temp. humidity meter. Fluke-971 Sr. No.56-123 (Source humidity chamber) V. Time & Frequency Parameter/Equipment Range CMC 2,3 ( ) Comments Frequency Measuring Equipment (0 to 10) Hz (10 to 100 Hz (100 to 250) Hz 0.003 % + 0.002 Hz 0.004 % + 0.012 Hz 0.005 % + 0.01 Hz Tachometer (20 to 1800) rpm (1800 to 2400) rpm (2400 to 99 000) rpm 1.2 rpm 1.2 rpm 1.3 rpm 1 This laboratory offers commercial calibration service. Page 11 of 12
2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a Laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of Confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 In the statement of CMC, the value is defined as the percentage of reading, unless otherwise noted. 4 The standard values are determined using the indicated instrument (see Comments.) This capability is suitable for the calibration of the device intended to measure or generated the measured value in the ranges indicated. CMC are express as either a specific value that covers the full range or as a percentage or fraction of the reading plus a fixed floor specification. Page 12 of 12
Accredited Laboratory A2LA has accredited FUGRO SUHAIMI LIMITED, YANBU Madinat Yanbu Al-Sinaiyah, KINGDOM OF SAUDI ARABIA for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSLI Z540-1-1994 and R205 Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 28 th day of March 2017. President and CEO For the Accreditation Council Certificate Number 3512.10 Valid to December 31, 2018 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.