DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODEL CC0XL (Gas) May 0 Part #00
GENERAL SAFETY WARNINGS AND PRECAUTIONS PERSONAL SAFETY Read and understand all operating instructions before attempting to operate the saw. Always wear safety approved hearing, eye, head and respiratory protection. Always wear sturdy boots with non-slip soles to ensure proper footing. Use of steel toed safety boots is recommended. Due to the nature of concrete cutting, sparks may be generated therefore never wear clothing that is made of flammable material. Know how to stop the saw quickly in case of emergency. Keep all parts of your body away from the blade and all other moving parts. Use caution and follow all instructions when loading and unloading the saw. BLADE SAFETY Examine cutting blades before each use. Blade should have no cracks, nick, or flaws. The center hole must be undamaged. Use only blades recommended for you particular model saw. The saw should only be used for cutting material that is specified on each cutting blade. Read the instructions provided with each blade to determine which material the blade is designed to cut. Use only reinforced abrasive blades or steel centered diamond blades manufactured for use on concrete saws. Inspect blade flanges for damage, excessive wear and cleanliness before mounting the blade. The blade must fit snuggly on the clean, undamaged blade shaft. Observe the specified maximum speed of the blade. Never use a blade that has a lower maximum operating speed than the blade shaft speed. The ignition governor is designed to limit the maximum no-load engine speed. Speeds in excess of that may cause the blade to exceed the maximum blade speed. Do not operate the unit at speeds greater than the maximum blade speed. Always keep guards in place and never allow the blade exposure on the guard to exceed 0 degrees. Repair or replace damaged guards immediately. Never expose anyone to the direct line of the blade. Make sure that the blade does not come in contact with the ground or any other surface when transporting the saw. GENERAL SAW SAFETY The saw must never be left unattended when the engine is running. Keep both hands on the handles when operating the saw. Never operate the saw if there is a fuel leak. Use extreme caution and slow speed when using the self propelled drive to move the saw up or down ramps or when loading and unloading from trucks or trailers. When going down ramps, DRIVE the saw forward slowly. When going up ramps, BACK the saw in reverse slowly. CUTTING / WORK AREA SAFETY Never operate the saw in any application or job in which you are not trained or supervised. Always ensure that the work area does not contain any buried or embedded electrical lines, gas lines or water lines. Ensure that all electricity in the ground, floor, walls or ceilings is shut off prior to cutting. Ensure that all gas and water lines that may be buried or embedded in the ground, floor, walls or ceilings are shut off prior to cutting. Operate the saw only in well ventilated areas. Engine exhaust contains carbon monoxide which can cause loss of consciousness and death. Keep bystanders and animals out of the work area. Observe all safety regulations for the safe handling of fuel. Store fuel in appropriate safety containers. Shut off the engine and allow it to cool prior to fueling. Wipe off any spilled fuel. Always move away from the fueling area prior to starting saw. Do not operate the saw in areas which contain combustible material or fumes. Sparks may occur from cutting that could cause a fire or explosion. Concrete cutting as all construction work is inherently dangerous! Failure to comply with the preceding warnings could result in serious bodily injury!
Table of Contents Description Page No. Common Parts...... - Front Axle Assembly...... Screw Feed Assembly..... Engine Group Horsepower Honda.... - Engine Group Horsepower Honda...... - Engine Group Horsepower Honda for 0" Guard...... - Engine Group Horsepower Robin......... - Blade Shaft Assembly... Blade Guard Assembly.... Blade Guard Assembly.... 0 Blade Guard Assembly.... Pointer Assembly.........0 Water Tank Option Group.. Notes... Warranty.. Quick Reference Service: Filters & Belts DP Part No. Description Manufacturer s Part No. 00 Air Filter for & HP Honda (Honda #-ZE-0) 0 Air Filter for HP Robin (Robin #-0-0) 0 Fuel Filter for HP Robin (Robin #0-00-) 000 Belt for HP Honda & HP Robin (Gates #VX) & HP Honda with 0" Blade Guard 000 Belt for HP Honda (Gates #VX00)
CC0XL Common Parts 0 0
CC0XL Common Parts - 00 (Regular Cut) - 0 (Upcut) ITEM PART NO. QTY. DESCRIPTION 0 Frame Weldment (Regular Cut) 0 Frame Weldment (Upcut) 0 Wheel, x x /" 00 Set Collar, /" 000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M-. x 0mm 00 Lock Washer, M Split 000 Belt Guard (Regular Cut) 0 Belt Guard (Upcut) 000 Cap Screw, Hex Hd., M-. x 0mm 00 Capscrew, Flat Hd., M x mm 00 Tapered Guard Mount 0 Tapered Guard Mount Spacer 00 Shaft Guard 00 Wrench Head 000 Wing Screw, M x mm 000 Capscrew, Soc. Hd., M X mm 0 Water Hose Assembly, 0" Long 00 Fitting, /" M. Pipe to /" M. Garden 000 Water Valve 0000 Close Nipple, /" NPT 0 000 Pipe Elbow, /" Female 00 Flat Washer, /" SAE 000 Fitting, /" F. Pipe to /" F. Garden 000 Hose Filter Washer 00 Indexing Plunger /- 00 Lift Bar Assembly 000 Lock Nut, /- Nylon 0000 Cap Screw, Hex Hd., /- x " 00 Sliding Handle Weldment 0 Cap, " Sq. Tube 0 00 Handle Grip 00 Cap Screw, Hex Hd., /- x -/" 0 Front Axle Assembly 0 Screw Feed Assembly
Front Axle Assembly: 0 ITEM PART NO. QTY. DESCRIPTION 00 Front Axle Weldment 0 Retaining Ring, External /" 0000 Wheel, " x " x /" 0000 Flat Washer, /" SAE 000 Flg Mnt Brg /" Peer UCFT0--0 000 Carriage Bolt, /"- X -/" 00 Lock Washer, M Split 000 Lock Nut, M Nylon
Screw Feed Assembly #0 ITEM PART NO. QTY DESCRIPTION 0 Adjustment Shaft W/Grease Fitting 00 Clevis Pin, / x -/" 00 Hairpin Cotter, /" x /" to /" 000 Bearing, /", Two Bolt Flange 0 Adjustment Screw 0 Spacer Tube / x / 00 Woodruff Key, / x /, #0 00 Lock Nut, /-, Flex Top 0000 Handwheel, " x /" 00 Carriage Bolt, /-0 x -/", GR 000 Lock Nut, /-0 Nylon 00 Bellow, " Long 00 Bellow Mount Washer
CCXL Honda HP Engine Assembly, #000 0.....
CCXL Honda HP Engine Assembly, #000 ITEM PART NO. QTY. DESCRIPTION 000.0 HP Honda Engine GX0 0 Key, /" Sq. x -/" 000 Taper Bushing, " w/ Set Screws 000 Sheave,. - Groove 000 V-Belt, VX 0 Wire Harness, Stop Switch (Gas Saw Only) 0 Throttle Control, " 00 Belt Adjustment Weldment 000 Flat Washer, /" SAE 00 Flat Washer, /" USS 000 Flat Washer, # USS 000 Lock Nut, M-0. Nylon Insert 000 Cap Screw, Hex Hd., M-0. x 0mm 00 Hex Nut, M 00 Lock Washer, M Split 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x 0mm 00 Cap Screw, Hex Hd., M-. x mm 00 Cap Screw, Hex Hd., M-. x mm 0 00 Muffler Deflector, - HP Honda 000 Screw, Self Tapping, #- x /" 0 CC0 Adaptor Plate 00 Oil Drain Assembly. 0 /" x.00" Oil Drain Hose. 00 Adapter, M x. M to /" Male JIC. 000 Fitting, /" F. JIC to /" Pushlock. 0000 Cap, /" JIC. 0000 Fitting, /" M. JIC to /" Push Lock
CCXL Honda HP Engine Assembly, #00 0.....
CCXL Honda HP Engine Assembly, #00 ITEM PART NO. QTY. DESCRIPTION 00 Engine, HP Honda GX0 0 Key, /" Sq. x -/" 000 Taper Bushing, " w/ Set Screws 000 Sheave,. - Groove 000 V-Belt, VX00 0 Wire Harness, Stop Switch (Gas Saw Only) 0 Throttle Control, " 00 Belt Adjustment Weldment 000 Flat Washer, /" SAE 00 Flat Washer, /" USS 000 Flat Washer, # USS 000 Lock Nut, M-0. Nylon Insert 000 Cap Screw, Hex Hd., M-0. x 0mm 00 Hex Nut, M 00 Lock Washer, M Split 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x mm 00 Cap Screw, Hex Hd., M-. x 0mm 00 Muffler Deflector, - HP Honda 0 000 Screw, Self Tapping, #- x /" 00 Oil Drain Assembly. 0 /" x.00" Oil Drain Hose. 00 Adapter, M x. M to /" Male JIC. 000 Fitting, /" F. JIC to /" Pushlock. 0000 Cap, /" JIC. 0000 Fitting, /" M. JIC to /" Push Lock
CCXL Honda HP Engine Assembly For 0" Blade Guard #00 0.....
CCXL Honda HP Engine Assembly For 0" Blade Guard #00 ITEM PART NO. QTY. DESCRIPTION 00 Engine, HP Honda GX0 0 Key, /" Sq. x -/" 000 Taper Bushing, " w/ Set Screws 000 Sheave,. - Groove 000 V-Belt, VX 0 Wire Harness, Stop Switch (Gas Saw Only) 0 Throttle Control, " 00 Belt Adjustment Weldment 000 Flat Washer, /" SAE 00 Flat Washer, /" USS 000 Flat Washer, # USS 000 Lock Nut, M-0. Nylon Insert 000 Cap Screw, Hex Hd., M-0. x 0mm 00 Hex Nut, M 00 Lock Washer, M Split 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x 0mm 00 Cap Screw, Hex Hd., M-. x mm 00 Cap Screw, Hex Hd., M-. x mm 0 00 Muffler Deflector, - HP Honda 000 Screw, Self Tapping, #- x /" 0 Motor Mount Wedge 00 Oil Drain Assembly. 0 /" x.00" Oil Drain Hose. 00 Adapter, M x. M to /" Male JIC. 000 Fitting, /" F. JIC to /" Pushlock. 0000 Cap, /" JIC. 0000 Fitting, /" M. JIC to /" Push Lock
CCXL Robin HP Engine Assembly, #00..... 0
CCXL Robin HP Engine Assembly, #00 ITEM PART NO. QTY. DESCRIPTION 00.0 HP Robin Engine EX0 0 Key, /" Sq. x -/" 000 Taper Bushing, " w/ Set Screws 000 Sheave,. - Groove 000 V-Belt, VX 0 Wire Harness, Stop Switch (Gas Saw Only) 0 Throttle Control,." 00 Belt Adjustment Weldment 000 Flat Washer, /" SAE 00 Flat Washer, /" USS 000 Flat Washer, # USS 000 Lock Nut, M-0. Nylon Insert 000 Cap Screw, Hex Hd., M-0. x 0mm 00 Hex Nut, M 00 Lock Washer, M Split 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x 0mm 00 Cap Screw, Hex Hd., M-. x mm 00 Cap Screw, Hex Hd., M-. x mm 0 0 CC XL Adaptor Plate 00 Oil Drain Hose Assembly. 00 Oil Drain Hose, /" ID X " Long. 00 Fitting, /" M. Pipe to /" Pushlock. 0 Adapter, Mx. M. to /" F. Pipe. 0000 Fitting, /" M. JIC to /" Push Lock. 0000 Cap, /" JIC
Blade Shaft Assembly, #0 ITEM PART NO. QTY DESCRIPTION 0 Blade Shaft 000 Sheave,.- Groove 00 Flange Block Bearing, -/" 00 Bearing Spacer 00 Key, /" Sq. x /" 0 Key, /" Sq. x -/" 00 Taper Bushing, -/" 000 Inner Flange -/" 000 Flange Nut, /- R.H. 000 Outer Flange, -/" w/ Pin 000 Flange Nut, /- L.H. 000 Carriage Bolt, /"- X -/" 00 Lock Nut, M-. Nylon Insert
" Blade Guard Assembly #0..... ITEM PART NO. QTY. DESCRIPTION 0 " Blade Guard 00 Water Manifold Gasket 0 Water Manifold 0 Water Tube for " Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 0000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M x mm 000 Lock Nut, M Nylon 0 Water Tube Clamp 000 Cap Screw, Flat Hd. Soc., M x mm 00 Splash Flap 000 Flat Washer, # USS 000 Cap Screw, Hex Hd., M x 0mm 000 Fender Washer, /" I.D. x -/" O.D. 000 Lock Nut, M Nylon 000 Spring, / X.0 X " 00 Hinge Assy., Metric Fasteners. 000 Blade Guard Hinge. 0000 Flat Washer, /" SAE. 00 Cap Screw, Hex Hd., M x 0mm. 000 Lock Nut, M Nylon. 00 Cap Screw, Hex Hd., M x mm 0000 Warning Label
" Blade Guard Assembly #0 A ITEM PART NO. QTY. DESCRIPTION 00 " Blade Guard Assembly (Slip-On Style) 000 Blade Guard Hinge 00 Cap Screw, Hex Hd., M x 0mm 0000 Flat Washer, /" SAE 000 Lock Nut, M Nylon 0 Water Manifold 00 Water Manifold Gasket 0 Water Tube for " Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 00 Cap Screw, Hex Hd., M x mm 0 Water Tube Clamp 000 Cap Screw, Flat Hd. Soc., M x mm 000 Spring, /" x " 000 Lock Nut, M Nylon 000 Cap Screw, Hex Hd., M x 0mm 00 Splash Flap 000 Fender Washer, /" x -/" 000 Flat Washer, # USS
0" Blade Guard Assembly #00..... ITEM PART NO. QTY. DESCRIPTION 00 0" Blade Guard 00 Water Manifold Gasket 0 Water Manifold 00 Water Tube for 0" Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 0000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M x mm 000 Lock Nut, M Nylon 0 Water Tube Clamp 000 Cap Screw, Flat Hd. Soc., M x mm 00 Splash Flap 000 Flat Washer, # USS 000 Cap Screw, Hex Hd., M x 0mm 000 Fender Washer, /" x -/" 000 Lock Nut, M Nylon 000 Spring, /" x " 00 Hinge Assy., Metric Fasteners. 000 Blade Guard Hinge. 0000 Flat Washer, /" SAE. 00 Cap Screw, Hex Hd., M x 0mm. 000 Lock Nut, M Nylon 0000 Warning Label
Pointer Assembly - 000-0 (HP Electric) ITEM PART NO. QTY DESCRIPTION 00 Pointer Bar - Straight 000 Pointer Bar - Offset 00 Wheel, " 000 Lock Nut, /- Nylon 00 Lock Washer, M Split 000 Hex Nut, /- 000 Lock Nut, M Nylon 00 Cap Screw, Hex Hd., M x mm 00 Rope, / x " 00 Pinch Clamp, Two Ear 000 Pointer Rod 00 Ponter Rod (HP Electric) Pointer Assembly - 0 (Upcut) ITEM PART NO. 0 QTY. DESCRIPTION Bar, Pointer 000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M x mm 000 Lock Nut, M Nylon 0
WATER TANK OPTION: 000...... MOUNTS TO LIFT BAR. ITEM PART NO. QTY. DESCRIPTION 00 Water Tank W/Hose Assy.. 0 Water Tank Assy., -/ Galllon. 00 Petcock. 000 Hose Clamp #. 00 /"MPT X /" Hose Barb. 00 /" x -/" Clear Hose 00 Tiedown, Elastic, " 0 Water Hose Assembly, 0" Long
NOTES
Intentionally Blank
EQUIPMENT AND PARTS WARRANTY Diamond Products warrants all equipment manufactured by it against defects in workmanship or materials for a period of one () year from the date of shipment to Customer. The responsibility of Diamond Products under this Warranty is limited to replacement or repair of defective parts at Diamond Products Elyria, Ohio factory, or at a point designated by it, of such parts as shall appear to us upon inspection at such parts, to have been defective in material or workmanship, with expense for transportation and labor borne by Customer. In no event shall Diamond Products be liable for consequential or incidental damages arising out of the failure of any Product to operate properly. Integral units such as engines, electric motors, batteries, transmissions, etc., are excluded from this Warranty and are subject to the prime manufacturer s warranty. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ALL SUCH OTHER WARRANTIES ARE HEREBY DISCLAIMED. Prospect Street, Elyria, Ohio 0 (0) - (00) - Fax (0) - www.diamondproducts.com Printed in U.S.A. #00
CONCRETE SAW PARTS LIST MODEL CC0XL Electric Units August 0 Part 00
GENERAL SAFETY WARNINGS AND PRECAUTIONS PERSONAL SAFETY Read and understand all operating instructions before attempting to operate the saw. Always wear safety approved hearing, eye, head and respiratory protection. Always wear sturdy boots with non-slip soles to ensure proper footing. Use of steel toed safety boots is recommended. Due to the nature of concrete cutting, sparks may be generated therefore never wear clothing that is made of flammable material. Know how to stop the saw quickly in case of emergency. Keep all parts of your body away from the blade and all other moving parts. Use caution and follow all instructions when loading and unloading the saw. Electric Units: disconnect power cord prior to changing the blade or performing maintenance. BLADE SAFETY Examine cutting blades before each use. Blade should have no cracks, nicks, or flaws. The center hole must be undamaged. Use only blades recommended for your particular model saw. The saw should only be used for cutting material that is specified on each cutting blade. Read the instructions provided with each blade to determine which material the blade is designed to cut. Use only reinforced abrasive blades or steel centered diamond blades manufactured for use on concrete saws. Inspect blade flanges for damage, excessive wear and cleanliness before mounting the blade. The blade must fit snuggly on the clean, undamaged blade shaft. Observe the specified maximum speed of the blade. Never use a blade that has a lower maximum operating speed than the blade shaft speed. The ignition governor is designed to limit the maximum no-load engine speed. Speeds in excess of that may cause the blade to exceed the maximum blade speed. Do not operate the unit at speeds greater than the maximum blade speed. Always keep guards in place and never allow the blade exposure on the guard to exceed 0 degrees. Repair or replace damaged guards immediately. Never expose anyone to the direct line of the blade. Make sure that the blade does not come in contact with the ground or any other surface when transporting the saw. GENERAL SAW SAFETY The saw must never be left unattended when the engine is running. Keep both hands on the handles when operating the saw. Use caution and slow speed when using the self propelled drive to move the saw up or down ramps or when loading and unloading from trucks or trailers. When going down ramps, DRIVE the saw forward slowly. When going up ramps, BACK the saw in reverse slowly. Always position yourself on the high side of the slope. Gas Units: never operate the saw if there is a fuel leak. CUTTING / WORK AREA SAFETY Never operate the saw in any application or job in which you are not trained or supervised. Always ensure that the work area does not contain any buried or embedded electrical lines, gas lines or water lines. Ensure that all electric, gas and water lines that may be buried or embedded in the ground, floor, walls or ceilings are shut off prior to cutting. Keep bystanders and animals out of the work area. Do not operate the saw in areas which contain combustible material or fumes. Sparks may occur from cutting that could cause a fire or explosion. Gas Units: operate the saw only in well ventilated areas. Engine exhaust contains carbon monoxide which can cause loss of consciousness and death. Gas Units: observe all safety regulations for the safe handling of fuel. Store fuel in appropriate safety containers. Shut off the engine and allow it to cool prior to fueling. Wipe off any spilled fuel. Always move away from the fueling area prior to starting saw. Concrete cutting as all construction work is inherently dangerous! Failure to comply with the preceding warnings could result in serious bodily injury!
NOTES
Table of Contents Description Page No. Common Parts...... Front Axle Assembly...... Screw Feed Assembly....... Motor Assembly, HP, 0V, Phase.... Motor Assembly, HP, 0V, Phase..... Motor Assembly, HP, 0V, Phase....... Motor Assembly, HP, 0V, Phase......... Motor Assembly, HP, 0V, Phase... Motor Assembly, HP, V, Phase... 0 Starter Box Assembly, Phase, 0-0V... Starter Box Assembly, Phase, -0V... Starter Box Assembly, Phase, 0-00V... Starter Box, 0-0V... Starter Box, -0V... Starter Box, 0-00V... 0 Blade Shaft Assembly... Blade Shaft Assembly (HP, 0/0V Units)... Blade Shaft Assembly (HP, V Units)... Blade Guard Assembly... Blade Guard Assembly... 0 Blade Guard Assembly... Pointer Assembly... Pointer Assembly (HP Units)... Warranty...... Rear Cover
00 CC0 XL COMMON PARTS 0 DETAIL B SCALE : 0 TO BLADE GUARD 0 DETAIL A SCALE :
CC0XL COMMON PARTS - 00 (Regular Cut) - 0 (Upcut) ITEM PART NO. Default /QTY. DESCRIPTION 0 Frame Weldment (Regular Cut) 0 Frame Weldment (Upcut) 0 Wheel, x x /" 00 Set Collar, /" 000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M-. x 0mm 00 Lock Washer, M Split 000 Belt Guard (Regular Cut) 0 Belt Guard (Upcut) 000 Cap Screw, Hex Hd., M-. x 0mm 00 Capscrew, Flat Hd., M x mm 00 Tapered Guard Mount 0 Tapered Guard Mount Spacer 00 Shaft Guard 00 Wrench Head 000 Wing Screw, M x mm 000 Capscrew, Soc. Hd., M X mm 0 Water Hose Assembly, 0" Long 00 Fitting, /" M. Pipe to /" M. Garden 000 Water Valve 0000 Close Nipple, /" NPT 0 000 Pipe Elbow, /" Female 00 Flat Washer, /" SAE 000 Fitting, /" F. Pipe to /" F. Garden 000 Hose Filter Washer 00 Indexing Plunger /- 00 Lift Bar Assembly 000 Lock Nut, /- Nylon 0000 Cap Screw, Hex Hd., /- x " 00 Sliding Handle Weldment 0 Cap, " Sq. Tube 0 00 Handle Grip 00 Cap Screw, Hex Hd., /- x -/" 0 Front Axle Assembly 0 Screw Feed Assembly
0 Front Axle Assembly ITEM PART NO. QTY. DESCRIPTION 00 Front Axle Weldment 0 Retaining Ring, External /" 0000 Wheel, " x " x /" 0000 Flat Washer, /" SAE 000 Flg Mnt Brg /" Peer UCFT0--0 00 Carriage Bolt, M-. x 0 00 Lock Washer, M Split 000 Lock Nut, M-. Nylon Insert
Screw Feed Assembly #0 ITEM PART NO. QTY DESCRIPTION 0 Adjustment Shaft W/Grease Fitting 00 Clevis Pin, / x -/" 00 Hairpin Cotter, /" x /" to /" 000 Bearing, /", Two Bolt Flange 0 Adjustment Screw 0 Spacer Tube / x / 00 Woodruff Key, / x /, #0 00 Lock Nut, /-, Flex Top 0000 Handwheel, " x /" 00 Carriage Bolt, /-0 x -/", GR 000 Lock Nut, /-0 Nylon 00 Bellow, -/" 00 Bellow Mount Washer 0 Hose Clamp #
0 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE X DETAIL C SCALE : DETAIL B SCALE : SHOWN FOR REFERENCE REF: OVERLOAD SWITCH IS 0 X DETAIL A SCALE :.
0 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE ITEM PART NO. QTY. DESCRIPTION 00 Motor, HP, 0V, Ph, W/Switch Box 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 000 Sheave,. - Groove 000 Taper Bushing, -/" W/ Setscrews & Key 000 V-Belt, VX00 0 Hose Clamp, /" x /" Wide 00 Ampmeter, 0-0 Amp, AC 000 AC Current Transformer 00 Voltage Label, 0V 0000 Flat Washer, /" SAE 000 Lock Washer, /" Split 00 Cap Screw, Hex Hd., /-0 x /" 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly WITH UPCUT FRAME,0, REVERSE MOTOR MOUNTING.
0 CC0XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE DETAIL B SCALE : SHOWN FOR REFERENCE X 0 DETAIL C SCALE :. X DETAIL A SCALE :.
0 CC0XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE ITEM PART NO. QTY. DESCRIPTION 0000 HP, Ph, 0V Motor W/Starter Box 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 000 Sheave,. - Groove 000 Taper Bushing, -/" W/ Setscrews & Key 000 V-Belt, VX00 00 Amp Meter w/ Bracket, 0-0 AC 000 AC Current Transformer 0000 Machine Screw, Rd. Hd., #- x /" 000 Lock Washer, # Split 000 Hex Nut, #- 00 Heater,.-. Amp 00 Voltage Label, 0V 00 Flat Washer, M 000 Cap Screw, Hex Hd., M-0. x 0mm 0 000 Lock Nut, M-0. Nylon Insert 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly
0 CC0XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE DETAIL B SCALE : SHOWN FOR REFERENCE X 0 DETAIL C SCALE :. X DETAIL A SCALE :.
0 CC0XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE ITEM PART NO. QTY. DESCRIPTION 0000 HP, Ph, 0V Motor W/ Starter Box 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 000 Sheave,. - Groove 000 Taper Bushing, -/" W/ Setscrews & Key 000 V-Belt, VX00 00 Amp Meter w/ Bracket, 0-0 AC 000 AC Current Transformer 0000 Machine Screw, Rd. Hd., #- x /" 000 Lock Washer, # Split 000 Hex Nut, #- 00 Heater,. -. Amp 00 Voltage Label, 0V 00 Flat Washer, M 000 Cap Screw, Hex Hd., M-0. x 0mm 0 000 Lock Nut, M-0. Nylon Insert 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly
000 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE DETAIL B SCALE : X SHOWN FOR REFERENCE X DETAIL A SCALE :
000 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE ITEM PART NO. NUMBER QTY. DESCRIPTION 00 Motor, hp Phase Baldor 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 00 Key, /" Sq. x -/" 0 Sheave,. - Groove 000 Set Screw, Soc. Hd., /- x /" 0 Blade Guard Spacer 000 Cap Screw, Flat Hd., M-. x 0mm 000 V-Belt, VX00 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly 00 Starter Box Assembly, -Phase, 0-0V 00 Cap Screw, Hex Hd., M-.0 x mm 00 Lock Washer, M Split 0 Fender Washer, M
00 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE X DETAIL B SCALE : SHOWN FOR REFERENCE X DETAIL A SCALE :
00 CC0 XL ELECTRIC MOTOR OPTION, HP, 0V, -PHASE ITEM PART NO. NUMBER QTY. DESCRIPTION 00 Motor, hp Phase Baldor 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 00 Key, /" Sq. x -/" 0 Sheave,. - Groove 000 Set Screw, Soc. Hd., /- x /" 0 Blade Guard Spacer 000 Cap Screw, Flat Hd., M-. x 0mm 000 V-Belt, VX00 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly 00 Cap Screw, Hex Hd., M-.0 x mm 00 Lock Washer, M Split 0 Fender Washer, M 00 Starter Box Assembly, -Phase, -0V
0 CC0 XL ELECTRIC MOTOR OPTION, HP, V, -PHASE DETAIL B SCALE : X SHOWN FOR REFERENCE X DETAIL A SCALE : 0
0 CC0 XL ELECTRIC MOTOR OPTION, HP, V, -PHASE ITEM NO. PART NUMBER QTY. DESCRIPTION 000 Motor, HP, V, PH. Baldor 00 Belt Adjustment Weldment 00 Flat Washer, /" USS 00 Lock Washer, M Split 00 Hex Nut, M-. 00 Cap Screw, Hex Hd., M-. x 0mm 000 Lock Nut, M-. Nylon Insert 00 Key, /" Sq. x -/" 0 Sheave,. - Groove 000 Set Screw, Soc. Hd., /- x /" 00 Blade Guard Spacer, " 0 Cap Screw, Flat Hd., M-. x 0mm 000 V-Belt, VX00 0 Frame Weldment (Regular Cut) 00 Lift Bar Assembly 000 Starter Box Assembly, -Phase, 0-00V 00 Cap Screw, Hex Hd., M-.0 x mm 00 Lock Washer, M Split 0 Fender Washer, M
STARTER BOX ASSEMBLY,? -PHASE, 0-0V TO STARTER #00 BOX OVERLOAD TO MOTOR FOR CUSTOMER SUPPLIED POWER CORD ITEM PART NO. QTY. DESCRIPTION 000 Starter Box, 0-0V 00 Amp Meter w/ Bracket, 0-0 AC 000 AC Current Transformer 0000 Machine Screw, Rd. Hd., #- x /" 000 Lock Washer, # Split 000 Hex Nut, #- 00 Voltage Label, 0V 00 Cord Connector, /" Thd.,.-" Cord, 0 Deg. 0 Lock Nut, /" 00 Cord Grip, /-/", 0 Deg. 00 Lock Nut, " 00 Cable Assy., Ga., Wire x "
STARTER BOX ASSEMBLY, -PHASE, -0V #00 TO STARTER BOX OVERLOAD TO MOTOR FOR CUSTOMER SUPPLIED POWER CORD ITEM PART NO. QTY. DESCRIPTION 000 Starter Box, -0V 00 Amp Meter, 0-0 AC 000 AC Current Transformer 0000 Machine Screw, Rd. Hd., #- x /" 000 Lock Washer, # Split 000 Hex Nut, #- 00 Voltage Label, 0V 00 Cord Connector, /" Thd.,.-" Cord, 0 Deg. 0 Lock Nut, /" 00 Cord Grip, /-/", 0 Deg. 00 Lock Nut, " 00 Cable Assy., Ga., Wire x "
Intentionally Blank
STARTERBOX ASSEMBLY,? -PHASE, 0-00V #000 TO STARTER BOX OVERLOAD TO MOTOR ITEM PART NO. QTY. DESCRIPTION 00 Starter Box, 0-00V 00 Amp Meter, 0-0 AC 000 AC Current Transformer 0000 Machine Screw, Rd. Hd., #- x /" 000 Lock Washer, # Split 000 Hex Nut, #- 00 Voltage Label, V 00 Cord Connector, /" Thd.,.-" Cord, 0 Deg. 0 Lock Nut, /" 00 Cord Grip, /-/", 0 Deg. 00 Lock Nut, " 00 Cable Assy., Ga., Wire x " FOR CUSTOMER SUPPLIED POWER CORD
STARTER BOX, 0-0 VOLT #000
STARTER BOX, 0-0 VOLT #000 SET TO MOTOR AMP RATING TRIP CLASS - RESET - A PHASE - OFF N.O. ONLY ITEM PART NO. QTY. DESCRIPTION 0000D Starter Box Base 0 M-.0 Threaded Insert 00 Sub-plate 00 Machine Screw, Pan Hd., M-0. x mm 00 Contactor, 0-0V (includes coil) 0 Replacement Coil, 0-0V 0 Overload Relay, - AMP 0 Auxilary Contacts, NO-NC 0 Cap Screw, Soc. Hd., #- x /" 0 Flat Washer, # 00 Grounding Lug 000 Lock Washer, /" Split 0 Cap Screw, Hex Hd., /- x /" 0 E-Stop Switch, 00V 0 Pushbutton, N.O., 00V 0 Starter Box Cover 0 Fastener, Electrical Box Top
STARTER BOX, -0 VOLT #000
STARTER BOX, -0 VOLT #000 SET TO MOTOR AMP RATING TRIP CLASS - RESET - A PHASE - OFF N.O. ONLY ITEM PART NO. QTY. DESCRIPTION 0000D Starter Box Base 0 M-.0 Threaded Insert 00 Sub-plate 00 Machine Screw, Pan Hd., M-0. x mm 00 Contactor, -0V (Includes Coil) 0 Replacement Coil, -0V 0 Overload Relay, - AMP 0 Auxilary Contacts, NO-NC 0 Cap Screw, Soc. Hd., #- x /" 0 Flat Washer, # 0 Cap Screw, Hex Hd., /- x /" 0000 Flat Washer, /" SAE 00 Grounding Lug 0 E-Stop Switch, 00V 0 Pushbutton, N.O., 00V 0 Starter Box Cover 0 Fastener, Electrical Box Top
STARTER BOX, 0-00 VOLT #00 0
STARTER BOX, 0-00 VOLT #00 SET TO MOTOR AMP RATING TRIP CLASS - RESET - A PHASE - OFF N.O. ONLY ITEM PART NO. QTY. DESCRIPTION 0000D Starter Box Base 0 M-.0 Threaded Insert 00 Sub-plate 00 Machine Screw, Pan Hd., M-0. x mm 00 Contactor, 0-00V (includes coil) 0 Replacement Coil, 0-00V 0 Overload Relay, - AMP 0 Auxilary Contacts, NO-NC 0 Cap Screw, Soc. Hd., #- x /" 0 Flat Washer, # 00 Grounding Lug 000 Lock Washer, /" Split 0 Cap Screw, Hex Hd., /- x /" 0 E-Stop Switch, 00V 0 Pushbutton, N.O., 00V 0 Starter Box Cover 0 Fastener, Electrical Box Top
Blade Shaft Assembly, #0 ITEM PART NO. QTY. DESCRIPTION 0 Blade Shaft 00 Flange Block Bearing, -/" 00 Bearing Spacer 00 Key, /" Sq. x /" 0 Key, /" Sq. x -/" 000 Sheave,.- Groove 00 Taper Bushing, -/" 000 Inner Flange -/" 000 Flange Nut, /- R.H. 000 Outer Flange, -/" w/ Pin 000 Flange Nut, /-, L. Hand 00 Lock Nut, M-. Nylon Insert 00 Carriage Bolt, M-. x 000 Set Screw, Soc. Hd., /-0 x /"
0000 BLADE SHAFT ASSEMBLY, HP, 0/0 VOLT ALSO FIT VOLT MODELS PRIOR TO MARCH 0. ITEM PART NO. QTY. DESCRIPTION 0 Blade Shaft 00 Flange Block Bearing, -/" 00 Bearing Spacer 00 Key, /" Sq. x /" 0 Key, /" Sq. x -/" 00 Sheave, V-.- Groove () 00 Taper Bushing, -/" w/ Set Screws 000 Inner Flange -/" 000 Flange Nut, /- R.H. 000 Outer Flange, -/" w/ Pin 000 Flange Nut, /- L.H. 00 Lock Nut, M Nylon 00 Carriage Bolt, M-. x 000 Set Screw, Soc. Hd., /-0 x /"
00 BLADE SHAFT ASSEMBLY, V UNITS. ITEM PART NO. QTY. DESCRIPTION 00 Blade Shaft 00 Flange Block Bearing, -/" 00 Bearing Spacer 00 Key, /" Sq. x /" 0 Key, /" Sq. x -/" 00 Sheave, V-.- Groove () 00 Taper Bushing, -/" w/ Set Screws 000 Inner Flange -/" 000 Flange Nut, /- R.H. 000 Outer Flange, -/" w/ Pin 000 Flange Nut, /- L.H. 00 Lock Nut, M Nylon 00 Carriage Bolt, M-. x 000 Set Screw, Soc. Hd., /-0 x /"
" Blade Guard Assembly #0..... ITEM PART NO. QTY. DESCRIPTION 0 " Blade Guard 00 Water Manifold Gasket 0 Water Manifold 0 Water Tube for " Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 0000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M x mm 000 Lock Nut, M Nylon 0 Water Tube Clamp 000 Cap Screw, Flat Hd. Soc., M x mm 00 Splash Flap 000 Flat Washer, # USS 000 Cap Screw, Hex Hd., M x 0mm 000 Fender Washer, /" I.D. x -/" O.D. 000 Lock Nut, M Nylon 000 Spring, / X.0 X " 00 Hinge Assy., Metric Fasteners. 000 Blade Guard Hinge. 0000 Flat Washer, /" SAE. 00 Cap Screw, Hex Hd., M x 0mm. 000 Lock Nut, M Nylon. 00 Cap Screw, Hex Hd., M x mm 0000 Warning Label
" Blade Guard Assembly 0.... ITEM PART NO. QTY. DESCRIPTION 00 " Blade Guard Assembly 00 Water Manifold Gasket 0 Water Manifold 0 Water Tube for " Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 0000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M-.0 x mm 0 Water Tube Clamp 000 Lock Nut, M Nylon 000 Cap Screw, Flat Hd., M-.0 x mm 00 Splash Flap 000 Flat Washer, # USS 000 Cap Screw, Hex Hd., M-0. x 0mm 000 Spring, /" x " 000 Lock Nut, M-0. Nylon Insert 000 Fender Washer, /" x -/" 00 Hinge Assy., Metric Fasteners. 000 Blade Guard Hinge. 0000 Flat Washer, /" SAE. 00 Cap Screw, Hex Hd., M x 0mm. 000 Lock Nut, M Nylon 0000 Warning Label
0" Blade Guard Assembly #00..... ITEM PART NO. QTY. DESCRIPTION 00 0" Blade Guard 00 Water Manifold Gasket 0 Water Manifold 00 Water Tube for 0" Guard 0000 Plug, /" NPT 0000 Fitting, /" M. Pipe to /" M. Garden 0000 Flat Washer, /" SAE 00 Cap Screw, Hex Hd., M x mm 000 Lock Nut, M Nylon 0 Water Tube Clamp 000 Cap Screw, Flat Hd. Soc., M x mm 00 Splash Flap 000 Flat Washer, # USS 000 Cap Screw, Hex Hd., M x 0mm 000 Fender Washer, /" x -/" 000 Lock Nut, M Nylon 000 Spring, /" x " 00 Hinge Assy., Metric Fasteners. 000 Blade Guard Hinge. 0000 Flat Washer, /" SAE. 00 Cap Screw, Hex Hd., M x 0mm. 000 Lock Nut, M Nylon 0000 Warning Label
000 POINTER ASSEMBLY ITEM NO. PART NUMBER Default/ QTY. DESCRIPTION 00 Pointer Bar - Straight 000 Pointer Bar - Offset 00 Wheel, " 000 Lock Nut, /- Nylon 0000 Lock Washer, /" Split 000 Hex Nut, /- 000 Pointer Rod 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x mm 00 Rope, / x " 00 Pinch Clamp, Two Ear
0 POINTER ASSEMBLY, HP UNITS ITEM PART NO. Default/Q TY. DESCRIPTION 00 Pointer Bar - Straight 000 Pointer Bar - Offset 00 Wheel, " 000 Lock Nut, /- Nylon 00 Lock Washer, M Split 000 Hex Nut, /- 00 Pointer Rod, " 000 Lock Nut, M-. Nylon Insert 00 Cap Screw, Hex Hd., M-. x mm 00 Rope, / x " 00 Pinch Clamp, Two Ear
EQUIPMENT AND PARTS WARRANTY Diamond Products warrants all equipment manufactured by it against defects in workmanship or materials for a period of one () year from the date of shipment to Customer. The responsibility of Diamond Products under this Warranty is limited to replacement or repair of defective parts at Diamond Products Elyria, Ohio factory, or at a point designated by it, of such parts as shall appear to us upon inspection at such parts, to have been defective in material or workmanship, with expense for transportation and labor borne by Customer. In no event shall Diamond Products be liable for consequential or incidental damages arising out of the failure of any Product to operate properly. Integral units such as engines, electric motors, batteries, transmissions, etc., are excluded from this Warranty and are subject to the prime manufacturer s warranty. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ALL SUCH OTHER WARRANTIES ARE HEREBY DISCLAIMED.