MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual CD-4 CULTIVATING DISC IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. Made In CHINA 160 CORPORATE DRIVE, PO BOX 67, WARRENSBURG, MISSOURI 64093 PH 660. 747. 8183 FAX 660. 747. 8650 swisherinc.com 14674 REV. 07-344
LIMITED WARRANTY The manufacturer s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of One (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Commercial Use This product is not intended for commercial use and carries no commercial warranty. ) Limitation This warranty applies only to products which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher Mower Co., Inc., that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of the product. 3) Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal maintenance. In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-800--8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.
ASSEMBLY INSTRUCTIONS FOR ATV DISC Step 1: Assemble the two disc gang assemblies as shown in diagram Note: The diagram shows each item number as it is assembled onto the Square Axle Weldment. Tighten Lock Nut so all disc's are tight on Square Axle Weldment. 3
Step : Assemble the Hitch Tongue to the Frame using the Hex Bolts, Big Flat Washers and Lock Nuts. Note: Do not over tighten Hex Bolts and Lock Nuts, the Hitch Tongue should rotate up and down freely. Install the Wheel Bracket into the frame as shown in diagram. Note: Check the direction of angle iron on the wheel bracket as shown in diagram. 4
Step 3: Install the two Disc Gang assemblies to the frame using the U bolts and Lock Nuts as shown in diagram. Note: Install the two Disc Gang assemblies in the opposite direction, if they are installed incorrectly the disc will not function properly. Note: Install the two Disc Gang Assemblies onto the Frame in the opposite direction. 5
Step 4: Install the Mechanical Screw Jack onto the frame as shown in the diagram using the Hex bolts and Lock Nuts. Note: Do not over tighten these two bolts and Lock Nuts. Mechanical Jack 6
Step 5: Install Adjustable Rod to the Hitch Tongue and the Frame using the Hex Bolts and Lock Nuts as Shown. Install the Tires onto the Wheel bracket using the Flat Washers, Hex Bolts and Lock Nuts as shown.
Step 6: There maybe some adjusting of the Hitch Tongue for the height of towing vehicle, this function can be performed by rotating handle on Adjusting Rod. Rotating the handle on the Mechanical Screw Jack will raise the tires up down. Adjust the height of the Hitch Tongue by rotating this handle. Adjust the tires up or down by rotating this handle. This illustration shows the position where the handle be when the disc is in use.
Exploded Parts Drawing
Parts List Item No Prt No Description Qty Prt No Item No Description Qty 1 14546 " Coupling 1 14555 1 Bearing 1 13767 Hex Bolt M1 80 3 15304 Thick Flat Washer Ø1 3 13671 Hex Lock Nut M1 9 14681 3 Threaded Rod 1 4 14547 Hitch Tongue 1 04900 4 Nylock Nut M4 5 14548 Adjustable Rod 1 14556 5 Disc Pressure Plate 6 14787 Hex Bolt M16 90 3 14557 6 Disc Support Plate 4 7 1530 Big Flat Washer Ø16 6 14558 7 Short Sleeve 8 8 14680 U style Bolt 4 14559 8 Bearing Base Assy' 4 9 14306 Nylock Nut M16 4 15305 9 Carriage Bolt M1 35 16 10 14849 End cap 7 14560 30 Square Axle Weldment 11 14784 Flat Washer Ø1 14561 31 Long Sleeve 4 1 14550 Handle Grip 1 1456 3 Disc 10 13 114 Hex Bolt M6 30 1 14563 33 Wheel Bracket 1 14 14551 Handle 1 14786 34 Flat Washer Ø0 6 15 1190 Nylock Nut M6 1 15306 35 Hex Bolt M5 5 16 15303 Big Flat Washer Ø1 1 14564 36 Tire 17 1455 Outside Sleeve 1 11994 37 Nylock Nut M5 18 14553 Inside Sleeve 1 15307 38 Flat Washer Ø4 19 13670 Hex Bolt M1 60 1 15308 39 Hex Bolt M16 80 1 0 14554 Frame 1
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945 Owner s Manual CD-4 ATV & LAWN ACCESSORIES WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INORMATION AVAILABLE: * PRODUCT * SERIAL NUMBER - * MODEL NUMBER - TYPE - * PART NUMBER WITH PAINT CODE * PART DESCRIPTION IMPORTANT Read and follow all Safety Precautions and Instructions Before Operating this Equipment. TELEPHONE - 1-800--8183 FAX - 1-660-747-8650 SWISHER MOWER & MACHINE CO. INC. 160 CORPORATE DRIVE P.O. BOX 67 WARRENSBURG, MO 64093 www.swisherinc.com