SuperSlot Technical Specification Revision 1.0 March 20, 2015 SuperSlot and the SuperSlot logo are trademarks of Sound Devices, LLC
This document is protected under Sound Devices, LLC non-disclosure agreement. Distribution without the expressed consent of Sound Devices is prohibited. Introduction SuperSlot is an electro-mechanical connection, developed and licensed by Sound Devices, to simplify the interconnection of wireless audio systems with audio mixers and cameras. Superslot offers power, signal, and control connections. SuperSlot-compatible products include wireless systems, cameras, and audio mixers. This SuperSlot Specification identifies the mechanical and electrical specifications of SuperSlot host and client devices. A SuperSlot host is typically an audio mixer/ recorder or camera. A SuperSlot client is typically a wireless receiver or transmitter. The host accommodates SuperSlot-compliant wireless receivers or transmitters from any manufacturer. SuperSlot uses the ubiquitous DB-25 connector for all electrical connections. The SuperSlot standard is fully backwards compatible with the Panasonic slot-type system, popularized by Panasonic cameras and first introduced by Ikegami. Electrical connections in the Panasonic-type slot are a subset of SuperSlot. Mechanically the two standards are identical. SuperSlot client products are compatible with Panasonic-type host devices, with reduced functionality. Panasonic-slot-type client products are compatible with SuperSlot host devices. Electrical Features Legacy Panasonic Slot Feature Compatibility: Wireless receiver compatibility Power supplied is 12V, unregulated Two-channel analog audio connections, variable audio levels Additional Features Provided in SuperSlot: Remote control is via UART so that a SuperSlot host can fully control a connected client. Accommodates up to a 4-channel receiver. Accommodates up to a 4-channel transmitter. AES digital audio connection may be used by receiver for full digital interconnect. Compatible with multiple, asynchronous AES audio streams. Supports SMPTE Linear Timecode connection. Genlock connection can be used by host to synchronize video. 6-18 VDC, 5W power is available for client. Requirements of receiver or transmitter (client): Accepts 6-18 VDC input voltage, 5 watts max. Client must turn on with application of DC power. Analog audio outputs must be configurable (through UART) to fixed output of +2 dbu +/-0.5 db. Standard UART Rx and Tx connections required. - 1 -
Recommended UART BAUD rate is 115k, 8n1. Lower rates can be used, but will result in slower communication of data. SuperSlot UART signaling is 3.3V but is 5V tolerant on signals from client. Transmitters must use AES connection for audio. Logic Interface ID Command The protocol of serial communication is outside the scope of this electromechanical specification. In addition to the sample commands listed below, Sound Devices will work to accommodate manufacturers existing command sets and protocols. Sample Receiver Commands Frequency Scan Squelch threshold Audio output level Pilot tone Battery levels Sample Transmitter Commands Frequency Output Power Audio Level Mute Battery levels - 2 -
SuperSlot DB-25 Pin Assignments DB-25 Pin required for SuperSlot Name Description Rx Tx 1 Gnd Ground 2 Ch 1+ analog / Ch1,2 AES + 3 Ch 1 - analog / Ch1,2 AES - Ch1 + analog audio out of Wireless Rx into Alternately, Ch1 and Ch 2 AES3+ (balanced, 110 ohm, transformerless). Ch1 - analog audio out of Wireless Rx into Alternately, Ch 1 and Ch 2 AES3- (balanced, 110 ohm, transformerless). 4 Gnd Ground for power 5 6-18 VDC 6 No Connect - Float 7 No Connect - Float 8 No Connect - Float 9 LTC to Tx 10 LTC from Rx to Camera 11 Genlock from Rx to Camera 12 No Connect - Float Power from SuperSlot into Wireless Rx or Tx. 6.0-18.0 V, 5W max. Linear Timecode. LTC = 0/3.3V level. Linear Timecode from Wireless Rx to Camera (compatible camera needed). LTC = 0/3.3V level. Genlock signal from Wireless Rx to Camera (compatible camera needed) TC Gen 13 Gnd Ground 14 Gnd Ground 15 Ch 2+ analog / Ch3,4 AES + 16 Ch 2- analog / Ch3,4 AES - Ch2 + analog audio out of Wireless Rx into Alternately, Ch3 and Ch4 AES3+ (balanced, 110 ohm, transformerless). Ch2 - analog audio out of Wireless Rx into Alternately, Ch3 and Ch4 AES3- (balanced, 110 ohm, transformerless). 17 No Connect - Float 18 Ch1,2 AES + out 19 Ch1,2 AES - out AES3 + (balanced, 110 ohm, transformerless) AES3 - (balanced, 110 ohm, transformerless) - 3 -
DB-25 Pin required for SuperSlot Name Description Rx Tx 20 Ch3,4 AES + out 21 Ch3,4 AES - out 22 UART Receive (0/3.3V) 23 UART Transmit (0/3.3V) 24 No Connect AES3 + (balanced, 110 ohm, transformerless) AES3 - (balanced, 110 ohm, transformerless) UART from Wireless Rx to SuperSlot. 0/3.3V signaling. Superslot is 5 V tolerant; high >2 V, low <0.8 V. UART from SuperSlot to Wireless Rx. 0/3.3 V signaling. 25 Gnd Ground TC Gen Notes: Wireless Rx indicates wireless receiver. Wireless Tx indicates wireless transmitter. The Wireless Rx can also be a timecode generator or similar product. All ground connections are required on both Tx s and Rx s. - 4 -
.142 REF 3.191 3.050 1.929 2.598 3.450 MA ETERNAL LENGTH SuperSlot Mechanical Specification.984 DIMESIONS ARE SYMMETRICAL ABOUT CENTER 1.500 MA ETERNAL HEIGHT TOP SIDE A 2.700 TOP SIDE A CUT AWAY ISO VIEW 3D MODEL OF SUPERSLOT AVAILABLE CONTACT SOUND DEVICES FILE NAME: superslot.step R.090 (4).750 M3x.5 THREAD (4) 2.700 B.750 FCI D-SUB CONNECTOR P/N - D25S24B4P00LF (or equivalent) SECTION A-A B SECTION B-B REVISION HISTORY REV DESCRIPTION DATE 000 RELEASED 2/4/2015 001 002 DATE: 02/04/15 Dimensions are in inches unless otherwise specified. Tolerance unless otherwise specified:. +/-.005". +/-.010". +/-.030" FILENAME: Angles +/-.5 E7556 State Road 23/33 Reedsburg, WI 53959 www.sounddevices.com PH: 608-524-0625 FA: 608-524-0655 SUPERSLOT MECHANICAL SPEC.000-5 -