K12 DOORS K12.12 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
CONTENTS 1. Door locks series 8600... K12.12.03 1.1. General K12.12.03 1.2. Turning of the latch bolt K12.12.03 2. Types... K12.12.04 2.1. Lock with latch bolt and dead bolt K12.12.04 2.2. Lock with narrow latch bolt and dead bolt K12.12.05 2.3. Lock with roller and dead bolt K12.12.06 2.4. Lock with dead bolt only K12.12.07 3. Section preparations for locks... K12.12.08 4. Door locks series 8600E... K12.12.09 5. Door locks series 9600 with SKG certificate... K12.12.10 6. Keeps... K12.12.12 6.1. General K12.12.12 6.2. Keeps in zinc alloy K12.12.12 6.3. Keeps in zinc alloy with faceplate in stainless steel K12.12.13 6.4. Keeps in stainless steel K12.12.14 6.5. Keeps in stainless steel with plastic case K12.12.14 7. Section preparations for keeps... K12.12.15 8. Electric strikes... K12.12.16 8.1. General information K12.12.16 8.2. Types and function K12.12.17 8.3. Electric strikes series 8355-.-. K12.12.18 9. Application examples... K12.12.20 K12.12.02
1. Door locks series 8600 1.1. General The dead bolt is pivoting, rather than sliding. It is therefore longer than conventional bolts, so there is the same proportion of the dead bolt within the lockcase as is engaged into the frame, making it extremely difficult for burglars to force entry. Faceplate (flat or U-form) in stainless steel. Very narrow lock: lockcase width = 15.5 mm. Locking and unlocking by a single turn of 360 with the cylinder key. The latch bolt can be operated by the door handle as well as by the key. Two holes above and below the handle opening allow the door handles to be screwed to each other through the lock, so there are no screws visible from the outside. In addition to a more pleasing look and increased security a much stronger fastening of the door handles is obtained. The lock can be used left hand and right hand simply by turning the latch bolt. The lock is manufactured completely from non-corroding materials. The locks are tested in accordance with the European standard EN 12209:2003/AC:2005 and obtained the following classification code: Category of use Durability Door mass Fire resistance 3 S 7 0 0 C 2 B A 2 0 Note: for locks series 8300: durability = X Finish: faceplate : stainless steel lockcase : zinc alloy latch bolt : zinc alloy nickel plated dead bolt : zinc alloy nickel plated Safety Corrosion resistance Note: When a lock (only series 8300) is mounted without cylinder, the plastic protection piece and screw should not be removed. Security Door application Type of key operation Type of spindle Key identification 1.2. Turning of the latch bolt Procedure: 1. Put the dead bolt (B) in locked position. 2. Pull the latch bolt (A) forwards with a pair of pliers. 3. Turn the latch bolt (A) 180. 4. Move the latch bolt (A) backwards. K12.12.03
2. Types K12.12 2.1. Lock with latch bolt and dead bolt Flat faceplate Order code A B C E 8601-16-30 27 30 16 8605-16-30 13.5 8601-16-35 32 35 16 8605-16-35 13.5 8301-16-40 37 40 16 8305-16-40 13.5 8601-20-30 27 30 20 8605-20-30 13.5 8601-20-35 32 35 20 8605-20-35 13.5 8301-20-40 37 40 20 8305-20-40 13.5 8601-24-30 27 30 24 8605-24-30 13.5 8601-24-35 32 35 24 8605-24-35 13.5 8301-24-40 37 40 24 8305-24-40 13.5 U-faceplate Order code A B C D E 8601-U22-25 22.5 29 22 6.5 8605-U22-25 14.5 8601-U22-30 27.5 34 22 6.5 8605-U22-30 14.5 8301-U22-35 32.5 39 22 6.5 8305-U22-35 14.5 8601-U24-25 22.5 29 24 6.5 8605-U24-25 14.5 8601-U24-27 24 29 24 5 8605-U24-27 14.5 8601-U24-30 27.5 34 24 6.5 8605-U24-30 14.5 8601-U24-32 29 34 24 5 8605-U24-32 14.5 8301-U24-35 32.5 39 24 6.5 8305-U24-35 14.5 8301-U24-37 34 39 24 5 8305-U24-37 14.5 K12.12.04
2.2. Lock with narrow latch bolt and dead bolt K12.12 Flat faceplate Order code A B C E 8601B-16-30 27 30 16 8605B-16-30 13.5 8601B-16-35 32 35 16 8605B-16-35 13.5 8301B-16-40 37 40 16 8305B-16-40 13.5 8601B-20-30 27 30 20 8605B-20-30 13.5 8601B-20-35 32 35 20 8605B-20-35 13.5 8301B-20-40 37 40 20 8305B-20-40 13.5 8601B-24-30 27 30 24 8605B-24-30 13.5 8601B-24-35 32 35 24 8605B-24-35 13.5 8301B-24-40 37 40 24 8305B-24-40 13.5 U-faceplate Order code A B C D E 8601B-U22-25 22.5 29 22 6.5 8605B-U22-25 14.5 8601B-U22-30 27.5 34 22 6.5 8605B-U22-30 14.5 8301B-U22-35 32.5 39 22 6.5 8305B-U22-35 14.5 8601B-U24-25 22.5 29 24 6.5 8605B-U24-25 14.5 8601B-U24-27 24 29 24 5 8605B-U24-27 14.5 8601B-U24-30 27.5 34 24 6.5 8605B-U24-30 14.5 8601B-U24-32 29 34 24 5 8605B-U24-32 14.5 8301B-U24-35 32.5 39 24 6.5 8305B-U24-35 14.5 8301B-U24-37 34 39 24 5 8305B-U24-37 14.5 K12.12.05
2.3. Lock with roller and dead bolt Flat faceplate Order code A B C 8611-16-30 27 30 8611-16-35 32 35 16 8311-16-40 37 40 8611-20-30 27 30 8611-20-35 32 35 20 8311-20-40 37 40 8611-24-30 27 30 8611-24-35 32 35 24 8311-24-40 37 40 U-faceplate Order code A B C D 8611-U22-25 22.5 29 6.5 8611-U22-30 27.5 34 22 6.5 8311-U22-35 32.5 39 6.5 8611-U24-25 22.5 29 6.5 8611-U24-27 24 29 5 8611-U24-30 27.5 34 6.5 24 8611-U24-32 29 34 5 8311-U24-35 32.5 39 6.5 8311-U24-37 34 39 5 Adjustable roller The roller has an adjustment range of 8 mm. Adjust the roller with a hexagonal spanner of 2.5 mm. K12.12.06
2.4. Lock with dead bolt only Flat faceplate Order code A B C 8621-16-30 27 30 8621-16-35 32 35 16 8321-16-40 37 40 8621-20-30 27 30 8621-20-35 32 35 20 8321-20-40 37 40 8621-24-30 27 30 8621-24-35 32 35 24 8321-24-40 37 40 U-faceplate Order code A B C D 8621-U22-25 22.5 29 6.5 8621-U22-30 27.5 34 22 6.5 8321-U22-35 32.5 39 6.5 8621-U24-25 22.5 29 6.5 8621-U24-27 24 29 5 8621-U24-30 27.5 34 6.5 24 8621-U24-32 29 34 5 8321-U24-35 32.5 39 6.5 8321-U24-37 34 39 5 K12.12.07
3. Section preparations for locks Profile with vent groove (Flat faceplate) Profile without vent groove (U-faceplate) Hole ø14 mm is not required for locks with roller or locks without latch bolt. R = Height reference. K12.12.08
4. Door locks series 8600E Type E = with deactivating mechanism: All locks with latch bolt series 8600 can be provided with this mechanism to deactivate the latch bolt. The latch bolt is deactivated by pushing it into the lockcase and by turning the small cover. Locks: With flat faceplate Order code A B C E 8601E-20-30 27 30 20 8605E-20-30 13.5 8601E-20-35 32 35 20 8605E-20-35 13.5 8301E-20-40 37 40 20 8305E-20-40 13.5 8601E-24-30 27 30 24 8605E-24-30 13.5 8601E-24-35 32 35 24 8605E-24-35 13.5 8301E-24-40 37 40 24 8305E-24-40 13.5 deactivate latch bolt With U-faceplate Order code A B C D E 8601E-U22-25 22.5 29 22 6.5 8605E-U22-25 14.5 8601E-U22-30 27.5 34 22 6.5 8605E-U22-30 14.5 8301E-U22-35 32.5 39 22 6.5 8305E-U22-35 14.5 8601E-U24-25 22.5 29 24 6.5 8605E-U24-25 14.5 8601E-U24-27 24 29 24 5 8605E-U24-27 14.5 8601E-U24-30 27.5 34 24 6.5 8605E-U24-30 14.5 8601E-U24-32 29 34 24 5 8605E-U24-32 14.5 8301E-U24-35 32.5 39 24 6.5 8305E-U24-35 14.5 8301E-U24-37 34 39 24 5 8305E-U24-37 14.5 K12.12.09
5. Door locks series 9600 with SKG certificate General information The Foundation for Quality of window and door systems (SKG) is a recognised and independent test institution. The Foundation tests and awards certificates for windows, doors, facades and fittings. SKG awards stars to specify the quality of high security fittings and complete windows and doors. There are 3 categories to distinguish the different classes of security: Standard: 1 star Heavy: 2 stars Extra heavy: 3 stars The conditions to obtain this product certificate are described in the SKG Regulations. The tests are done in accordance with NEN 5089 Safety against burglary of buildings: high security fittings. Door locks series 9600 look the same and are mounted in the same way as door locks series 8600, but offer a higher security against forced entry. The dead bolt is equipped with two invisible cemented carbide rollers, making it impossible to cut the bolt with a hacksaw. Recommended for double action doors and doors without rebate. These high security locks are especially adapted and reinforced to comply with the rigorous SKG standards for security against forced entry. The two fixing holes, above and below the handle follower are suitable for screws M6. All other dimensions of the SKG type are the same as the standard type. Cemented carbide rollers Lock with SKG certificate K12.12.10
With flat faceplate The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG. SKG-type Standard type Order code Category Certificate number Order code Page 9601-U24-25 417.152.02 8601-U24-25 K12.12.04 9605-U24-25 417.152.02 8605-U24-25 K12.12.04 9611-U24-25 417.152.02 8611-U24-25 K12.12.06 9621-U24-25 417.152.02 8621-U24-25 K12.12.07 9601-U24-30 417.152.02 8601-U24-30 K12.12.04 9605-U24-30 417.152.02 8605-U24-30 K12.12.04 9611-U24-30 417.152.02 8611-U24-30 K12.12.06 9621-U24-30 417.152.02 8621-U24-30 K12.12.07 9301-U24-35 417.152.06 8301-U24-35 K12.12.04 9305-U24-35 417.152.06 8305-U24-35 K12.12.04 9311-U24-35 417.152.06 8311-U24-35 K12.12.06 9321-U24-35 417.152.06 8321-U24-35 K12.12.07 K12.12.11
6. Keeps 6.1. General There are 3 types of keeps: keeps in zinc alloy with case for use with dead bolt. keeps in zinc alloy with stainless steel faceplate with case for use with dead bolt. keeps in stainless steel without case for use with dead bolt. keeps in stainless steel with plastic case for use with dead bolt. The keeps are suitable for locks with latch bolt and dead bolt, with roller and dead bolt, or with dead bolt only. The locks have been tested by SKG in the Netherlands. 2 stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG. 6.2. Keeps in zinc alloy The keeps are horizontally adjustable by means of serrated plates. The adjustment range is 3 mm. The keeps are encased which gives a neat appearance and keeps the frame section free from dirt. Finish: keeps in zinc alloy, coated natural colour. Fixing by means of serrated plates with a horizontal adjustment range 3 mm. Order code G H I 8351-1 5.5 0 18 8351-2 14.5 0 18 8351-3 11 0 18 8351-4 8.5 0 18 8351-5 5.5 5 18 8351-7 5.5 0 23 n 8351-10 K12.12.12
6.3. Keeps in zinc alloy with faceplate in stainless steel The keeps are encased which gives a neat appearance and keeps the frame section free from dirt. Finish: keeps in zinc alloy, coated natural colour. Faceplate in stainless steel. Order code G H 8351-11 11 0 8351-12 5.5 0 8351-14 8.5 0 8351-15 5.5 5 Fixing holes with a horizontal adjustment range of 3 mm. K12.12.13
6.4. Keeps in stainless steel Extra slim keeps for sections with minimal installation depth. Finish: keeps in stainless steel. Order code G H I J 8353-1 2.5 0 20 10 8353-3 3 0 24 12 8353-5 3 0 20 9 8353-7 3 0 24 9 8353-7B 3 5 24 9 8353-7C 3 5 24 9 Fixing holes with a horizontal adjustment range of 3 mm. Keep n 8353-7C is not horizontally adjustable. 6.5. Keeps in stainless steel with plastic case Extra slim keeps for sections with minimal installation depth. Finish: keeps in stainless steel, case in black plastic. Order code G H I J 8353-2 2.5 0 20 10 8353-4 3 0 24 12 8353-6 3 0 20 9 8353-8 3 0 24 9 8353-8B 3 5 24 9 8353-8C 3 5 24 9 Fixing holes with a horizontal adjustment range of 3 mm. Keep n 8353-8C is not horizontally adjustable. K12.12.14
7. Section preparations for keeps Profile with frame groove Profile without frame groove Keep A 8351-.. 60 8353-.. 85 R = Height reference. KEEP DETAIL adjustable KEEP DETAIL adjustable adjustable adjustable adjustable adjustable K12.12.15
8. Electric strikes 8.1. General information Small electric strike incorporating a spacesaving locking flap, especially developed for installation in aluminium doors. The flap rotates back within the keep when operated. Big advantage: the cut-out is much smaller making the installation aesthetically pleasing. Break-in resistance of strike: 3750 N. Width adjustment of the locking flap: 3 mm. Current consumption: Alternating current (AC): 250 ma at 12V Direct current (DC): 280 ma at 12V The electric strikes are handed. Mechanical Reset button Electrical release connection (version E) Release button Electrical connection Reset button Quick and easy electrical connection. Adjustment range The reset button applies only to type 128 where the strike is held in the release position until the door has been opened. This button resets the electric strike when the door opens. The release button (version E) allows to suspend temporarily the automatic locking upon closing the door. Only available for type 118 and 128. K12.12.16
8.2. Types and function Model 118 The door is only unlocked when you push a button. After releasing the button the door is locked again. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. Note: when the door is pushed open by the gaskets, the door can still be open after releasing the button. This can be solved by mounting a door closer on the door. Electric strike Door Operation This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door. Model 128 On releasing the electric strike, for example, from a button on an intercom system, the strike is held in the release position until the door has been opened. The electric strike resets when the door opens. This means there is no need to rush through the door. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. This type is available with release button (version E). The release button allows to suspend temporarily the automatic locking upon closing the door. Electric strike Door Operation Model 138 This type works on 12V DC or 24V DC and may be permanently connected to electrical current. The electric strike is mainly used in combination with an emergency or a fire center. In case of a power failure, the door can be opened. Electric strike Door Operation K12.12.17
8.3. Electric strikes series 8355-.-. Electric strikes with extended faceplate for latch bolt and dead bolt. Finish: keep in aluminium natural anodised. left hand = illustrated right hand = opposite view Order code A B C Possibilities 3 mm adjustment 8355-1 5 11.5 6.5 118 10-24V AC/DC 8355-2 8 8 3 8355-3 10 8 3 8355-4 12 8 3 8355-5 8 11.5 6.5 8355-6 15 8 3 118E 10-24V AC/DC 128 10-24V AC/DC 128E 10-24V AC/DC 138-12 12V DC left or right Movement of locking flap 8355-8 10 11.5 6.5 138-24 24V DC Order example: 8355-6-128E left This is an electric strike with release button (E) with faceplate height of 15 mm and an electric strike type 128 (see page K12.12.17) working on 10-24V AC/DC. K12.12.18
3 mm adjustment Order code Possibilities 118 10-24V AC/DC 8355-9 118E 10-24V AC/DC 128 10-24V AC/DC 128E 10-24V AC/DC left or right Movement of locking flap 138-12 12V DC 138-24 24V DC Order example: 8355-9-128E left This is an electric strike with release button (E) and with an electric strike type 128 (see page K12.12.17) working on 10-24V AC/DC. K12.12.19
9. Application examples Lock n 8601-20-35 Lock n 8611-U22-30 + keep n 8351-5 + keep n 8351-3 Lock n 8601B-20-35 + electric strike n 8355-1-. right K12.12.20