Energy Management Energy Meter with plug-in Output Modules Type EM4-DIN

Energy Management Energy Meter with plug-in Output Modules Type EM4-DIN Degree of protection (front): IP 40 Front dimensions: 9 DIN modules RS 422/485 Serial port by means of optional module Dual pulse output by means of optional module Alarm output (kw dmd) by means of optional module Digital inputs for the management of the time periods and of the H 2O and GAS meters Product description Three-phase energy meter with built-in configuration key-pad; particularly indicated for the metering and the management of the energy in addition to the metering and the management of the signals coming from the water and gas meters. Housing for DIN-rail or wallmounting, IP40 (front) protection degree. Completely sealable housing. In case of direct connection up to 100A, the measuring Type selection Range Code input terminals are suitable for cables with a cross-section area from 6 to 35 mm 2. The special design of the instrument s housing allows to add at any time the interface modules, even when the instrument is already installed. The following modules are available: - for all versions: pulse output; - only for the versions with auxiliary power supply: digital inputs, RS485 serial port and BUS Dupline. Power supply Class 1 (active energy) Class 2 (reactive energy) Three-phase multi-function energy meter Back-lighted LCD display 3 1 / 2 DGT instantaneous variables read-out 8 DGT + 7 1 / 2 DGT energy read-out Measurements of system and phase variables: W, Wdmd Measurements of total energies: kwh, kvarh Measurements of partial energies: kwh, kvarh Energy measurements according to EN61036 and EN61268 Energy measurements by time periods (t1-t2-t3-t4) selectable by input contacts Measurements of m 3 H 2O and m 3 GAS by means of input contacts TRMS measurements of distorted wave forms (voltages/currents) Two basic models: direct connection 20(100)AAC, CT 5(10)AAC and VT connection Self power supply (available for some models only) or auxiliary power supply: 24V, 48V, 115V, 230V, 50-60Hz; 18 to 60VDC, 77 to 143VDC How to order Model Range code System Power supply Slot A Slot B Slot A (retransmission) EM4-DIN AV5 3 X X XX Important note: The models from AV0 to AV7 can be equipped with any type of available modules (slot A and B). The models AV8 and AV9 can be equipped only with the O and R type modules. The AV8 and AV9 models can measure all the parameters even if the three phase system being connected is missing one phase. The AV2 model is suitable only for three-phase unbalanced system without neutral. Slot A (retransmission) cont. Auxiliary Power Supply: AV0: 208V L-L/20(100)AAC [3] AV1: 400V L-L/20(100)AAC [1] AV3: 660V L-L/20(100)AAC [2] AV4: 208V L-L/5(10)AAC [3] AV5: 400V L-L/5(10)AAC [1] AV6: 100V L-L/5(10)AAC [3] AV7: 660V L-L/5(10)AAC [2] Self Power Supply: AV2: 220V L-L/20(100)AAC [4] AV8: 208V L-L/20(100)AAC [1] AV9: 400V L-L/20(100)AAC [1] System 3 : Three-phase, unbalanced load with or without neutral For all versions A: 24VAC -15+10%, 50-60Hz B: 48VAC -15+10%, 50-60Hz C: 115VAC -15+10%, 50-60Hz D: 230VAC -15+10%, 50-60Hz 4: 18 to 60VDC 5: 77 to 143VDC AV2, AV8 and AV9 only X: Self Power Supply 400V L-L (-20+15%, 50-60Hz) 208V L-L (-20+15%, 50-60Hz) 220V L-L (-10+15%, 50-60Hz) [1] Un: -20+15% [2] Un: -30+15% [3] Un: -20+20% [4] Un: -10 +15% X: None O: AO2900 module Dual open collector output. Three operating modes: two pulse outputs (kwh and kvarh); one alarm output (kw dmd) and one pulse output (kwh or kvarh) one output remotely controlled by a serial port and one pulse output (kwh or kvarh) D: AQ2940 module Two digital inputs for the management of water and gas meters R: AO2910 module. One relay output + one open collector output. Operation modes like module AO2900 Slot B (retransmission) Only with A-B-C-D-4 power supply XX: None S0: AR2950 module RS422/485 serial port Specifications are subject to change without notice EM4 DIN DS ENG 311007 1

Input specifications Number of inputs Current 3 Voltage 4 Accuracy (display, RS485) Ib: 5A, Imax: 10A Ib: 20A, Imax:100A Un: see Range code on previous page Current from 0.003Ib to 0.2Ib: ±(0.5%RDG +3DGT) from 0.2Ib to Imax: ±(0.5%RDG +1DGT) Voltage in the range Un: ±(0,5% RDG + 1DGT) Frequency ±0.1% RDG (50 to 60 Hz) Active power (@ 25 C ± 5 C, R.H. 90%) ±(1% RDG +1DGT). PF 1, 0.1Ib to Imax, in the Un range; PF 0.5L, PF 0.8C, 0.2Ib to Imax, in the Un range Energies (@ 25 C ± 5 C, R.H. 90%) Class 1 acc. to EN61036 Class 2 acc. to EN61268 Ib: 5A, Imax: 10A 0.1Ib: 500mA, Start up current: 20mA Un: see table range code Ib: 20A, Imax: 100A 0.1Ib: 2A, Start up current: 80mA Un: see table range code Acc. to EN61036, EN61268 Additional errors Wave form <1% (3 rd harmonic: 10%) Voltage asymmetry < 0.5% (referred to Un) Magnetic induction 0 (up to 0.5 mt) HF Electromagnetic fields < 1% Operation of accessories 0 Temperature drift 200ppm/ C Sampling rate 1000 samplings/s @ 50Hz Display Type Back-lighted LCD Instantan. variables read-out 3 1 /2 DGT Energies Total: 8 DGT + 7 1 /2 DGT; Partial: 8 DGT + 7 1 /2 DGT; Max. and Min. indication Max. 1999 (99999999), Min. 0 Measurements Power, energy. TRMS measurements of distorted wave forms. Coupling type Direct Crest factor Ib 5A Ib 20A Current overload 3 (15A max. peak) 6 (127A max. peak) 5(10) A, for 10ms 300A max, @ 50Hz 5(10) A, for 500ms 200A max, @ 50Hz 5(10) A, permanent 10A, @ 50Hz 20(100) A, for 10ms 2700A max, @ 50Hz 20(100) A, permanent 100A, @ 50Hz Voltage overload Permanent 1.2 Un For 1s 2 Un Input impedance 400V L-L (AV1-AV5-AV9) > 720KΩ 208V L-L (AV0-AV4-AV8-AV2) > 720KΩ 660V L-L (AV3-AV7) > 1.97MΩ 100V L-L (AV6) > 400KΩ 5(10) A (AV4-AV5-AV6-AV7) < 0.3VA 20(100) A (AV0-AV1-AV3-AV8-AV9) < 4VA 20(100) A (AV2) < 4VA Frequency 50 to 60 Hz Interface module specifications RS422/RS485 (on request) Type Connections Addresses Protocol Data (bidirectional) Dynamic (reading only) Static (writing only ) Data format Baud-rate Insulation AR2950 module Multidrop bidirectional (static and dynamic variables) 2 or 4 wires, max. distance 1000m, termination directly on the module 255, selectable by key-pad MODBUS/JBUS Phase and system variables: see table Display pages All the programming data, reset of energy, activation of static output. Stored energy (EEPROM) max. 99.999.999 kwh/kvarh 1 start bit, 8 data bit, no parity, 1 stop bit 9600 bit/s By means of optocouplers, 2000 V RMS output to measuring inputs Digital outputs (on request) AO2900 module Pulse outputs Number of outputs 2 Number of pulses 2000 V RMS output to supply input To be used as energy retransmission, water and gas, remote static outputs and alarm. Three working modes are selectable: two pulse outputs (kwh and kvarh); one alarm output (kw dmd) and one pulse output (kwh or kvarh); one output remotely controlled by means of the serial port and one pulse output (kwh or kvarh) From 0.01 to 100 pulses programmable according to the selected CT and VT ratios Output type Open collector (NPN transistor ) V ON 1.2 VDC / max. 100 ma 2 Specifications are subject to change without notice EM4 DIN DS ENG 311007

Interface module specifications (cont.) V OFF 30 VDC max. Pulse duration 220 ms (ON), 220 ms (OFF) According to DIN43864 Alarm output Number of outputs 1 Alarm type Up alarm, down alarm. Setpoint adjustment 0 to 100% of the electrical scale Hysteresis 0 to 100% of the electrical scale On-time delay 0 to 255 seconds Response time 700 ms Output type Open collector (transistor NPN) V ON 1.2 VDC / max. 100 ma V OFF 30 VDC max. Insulation By means of optocouplers, 2000 V RMS outputs to measuring inputs, 2000 V RMS output to supply input. Insulation between the two outputs: functional AO2910 module Relay + open collector output. Working mode like AO2900. Pulse output One static output+one relay output, other characteristics like AO2900. Alarm output Only relay output, other characteristics like AO2900. Output type Static type like module AO2900; Relay type: SPDT, AC1, AC15: 1AAC @250VAC Insulation 2000 V RMS outputs to measuring inputs, 2000 V RMS output to Software functions Password Numeric code of max. 3 digits 2 protection levels of the programming data 1 st level Password 0, no protection 2 nd level Password from 1 to 1000, all data are protected Transformer ratio CT 1 to 5000 VT 1.0 to 199.9 and 200 to 1999 Note: The CT ratio * VT ratio mustnever exceed the value 5000. The current measuring inputs can manage CT s with a secondary of 1A and 5A (accuracy always refers Supply specifications supply input. Insulation between the two outputs: 2000 V RMS Digital inputs (on request) AQ2940 module Four working modes are selectable: total and partial energy meters (kwh and kvarh) without the use of digital inputs total and partial energy meters (kwh and kvarh) managed by time periods (t 1-t 2-t 3-t 4); total energy meters (kwh, kvarh) and total day-time/night GAS meter; total energy meters (kwh, kvarh), GAS and WATER meters; Number of inputs 2 Input frequency 20Hz max. Duty cycle 50% Prescaler adjustment Contact measur. voltage Contact measur. current Input impedance Contact resistance Insulation Display Variables Errors from 0,1 to 100,0 m 3 / pulse 12V < +Aux < 24VDC Logic status: OFF < 2V, ON > 10V 15mA max 1kΩ 1kΩ, close contact 100kΩ, open contact By means of optocouplers, 2000 V RMS digital inputs to measuring inputs, 2000 V RMS digital inputs to supply input. to 5A) Up to 4 variables per page Page 1: kwh-kvarh Page 2a: k Wh (t 1-t 2-t 3-t 4) k varh (t 1-t 2-t 3-t 4) Page 2b: GAS m 3 day-time tariff, GAS m 3 night tariff Page 2c: H 2O m 3, GAS m 3 Page 3: W L1 Page 4: W L2 Page 5: W L3 Page 6: W dmd Phase sequence, serial communication status, wrong connection of current measuring inputs. Self supplied version 400V L-L (-20% +15%, 50-60Hz) 208V L-L (-20% +15%, 50-60Hz) 220V L-L (-10+15%, 50-60Hz) Auxiliary power supply Energy consumption 230VAC -15 +10%, 50-60Hz 115VAC -15 +10%, 50-60Hz 48VAC; -15 +10%, 50-60Hz 24VAC; -15 +10%, 50-60Hz 18 to 60VDC; 77 to 143VDC 7VA Specifications are subject to change without notice EM4 DIN DS ENG 311007 3

General Specifications Operating temperature Storage temperature Installation category Display pages 0 to +55 C (32 F to 131 F) (R.H. < 90% non-condensing 40 C) -20 to +60 C (-4 F to 140 F) (R.H. < 90% non-condensing 40 C) Cat. III (IEC60664) Insulation 2000 VRMSbetween all inputs / outputs to earth Dielectric strength 4000 VRMS for 1 minute Noise rejection CMRR 100 db, 48 to 62 Hz EMC Burst 4kV/level 4 (EN61000-4-4) Immunity to irradiated electromagnetic fields 10V/m 26-1000MHz (EN61000-4-3) Electrostatic discharges 15kV (EN61000-4-2) Radio frequency emissions according to CISPR 14 and CISPR 22 Pulse voltage (1.2/50µs) 8kV (EN61000-4-5) Standards Safety IEC60664-1 Metrology Energy measurements: EN61036, EN61268. Pulse output DIN43864 Approvals CE Connections 5(10) A Screw-type, Cable cross-section area 4 mm 2 Connections 20(90) A Screw-type, Min./Max. cable cross-section area 6 mm 2 / 35 mm 2 Min./Max. screws tightening torque 2 Nm / 6 Nm (100A inputs) Min./Max. screws tightening torque 0,4 Nm / 0,8Nm (other inputs / outputs) Housing Dimensions 162.5 x 90 x 63 mm Material ABS, NORYL, PC self-extinguishing: UL 94 V-0 Mounting DIN-rail and wall Degree of protection Front: IP40 Connections: IP20 Weight 800 g approx. (packing included) Variables that can be displayed No 1 st variable 2 nd variable Notes 1 kwh kvarh 2a kwh (t 1 or t 1-t 2-t 3-t 4) kvarh (t 1 or t 1-t 2-t 3-t 4) Depending on the type of selection you have chosen. 2b Day-time GAS m 3 Night GAS m 3 For the energy it is possible to choose the following operating mode: 2c H 2O m 3 GAS m 3 t 1partial meters or t 1-t 2-t 3-t 4 multitariff selection 3 W L1 4 W L2 5 W L3 6 W dmd dmd = demand (integration time selectable from 1 to 30 min.) 7 Display of the serial communication status, phase sequence, wrong connection of current measuring inputs Used calculation formulas Phase variables Instantaneous effective voltage Note: RS422/RS485 dynamic data. The variables transmitted are the ones listed in the table above and those mentioned in the Display pages of WM22-DIN data sheet except for: THD A, THD V, A max, W dmdmax, and VA dmd max. Instantaneous active power System variables Equivalent system voltage Consumption recording Instantaneous power factor (TPF) Instantaneous effective current Instantaneous apparent power Instantaneous reactive power System reactive power System active power System apparent power System power factor (TPF) Note: i = phase (L1, L2 or L3) P = active power Q = reactive power t 1, t 2 = starting and ending time points of consumption recording n = time unit t= time interval of consumption recording n 1, n 2 = starting and ending discrete time points of consumption recording 4 Specifications are subject to change without notice EM4 DIN DS ENG 311007

Available models Type Inputs Power supply Ordering code EM4-DIN AV9.3.X. 400V L-L, 20(100)A Self power supply AG2200 EM4-DIN AV8.3.X. 208V L-L, 20(100)A Self power supply AG2201 EM4-DIN AV2.3.x 220V L-L, 20(100)A Self power supply AG2244 EM4-DIN AV1.3.D. 400V L-L, 20(100)A 230VAC, 50-60Hz AG2202 EM4-DIN AV0.3.D. 208V L-L, 20(100)A 230VAC, 50-60Hz AG2203 EM4-DIN AV3.3.D. 660V L-L, 20(100)A 230VAC, 50-60Hz AG2204 EM4-DIN AV1.3.C. 400V L-L, 20(100)A 115VAC, 50-60Hz AG2205 EM4-DIN AV0.3.C. 208V L-L, 20(100)A 115VAC, 50-60Hz AG2206 EM4-DIN AV3.3.C. 660V L-L, 20(100)A 115VAC, 50-60Hz AG2207 EM4-DIN AV1.3.B. 400V L-L, 20(100)A 48VAC, 50-60Hz AG2208 EM4-DIN AV0.3.B. 208V L-L, 20(100)A 48VAC, 50-60Hz AG2209 EM4-DIN AV3.3.B. 660V L-L, 20(100)A 48VAC, 50-60Hz AG2210 EM4-DIN AV1.3.A. 400V L-L, 20(100)A 24VAC, 50-60Hz AG2211 EM4-DIN AV0.3.A. 208V L-L, 20(100)A 24VAC, 50-60Hz AG2212 EM4-DIN AV3.3.A. 660V L-L, 20(100)A 24VAC, 50-60Hz AG2213 EM4-DIN AV5.3.D. 400V L-L, 5(10)A 230VAC, 50-60Hz AG2214 EM4-DIN AV4.3.D. 208V L-L, 5(10)A 230VAC, 50-60Hz AG2215 EM4-DIN AV7.3.D. 660V L-L, 5(10)A 230VAC, 50-60Hz AG2216 EM4-DIN AV5.3.C. 400V L-L, 5(10)A 115VAC, 50-60Hz AG2217 EM4-DIN AV4.3.C. 208V L-L, 5(10)A 115VAC, 50-60Hz AG2218 EM4-DIN AV7.3.C. 660V L-L, 5(10)A 115VAC, 50-60Hz AG2219 EM4-DIN AV5.3.B. 400V L-L, 5(10)A 48VAC, 50-60Hz AG2220 EM4-DIN AV4.3.B. 208V L-L, 5(10)A 48VAC, 50-60Hz AG2221 EM4-DIN AV7.3.B. 660V L-L, 5(10)A 48VAC, 50-60Hz AG2222 EM4-DIN AV5.3.A. 400V L-L, 5(10)A 24VAC, 50-60Hz AG2223 EM4-DIN AV4.3.A. 208V L-L, 5(10)A 24VAC, 50-60Hz AG2224 EM4-DIN AV7.3.A. 660V L-L, 5(10)A 24VAC, 50-60Hz AG2225 EM4-DIN AV6.3.D. 100V L-L, 5(10)A 230VAC, 50-60Hz AG2226 EM4-DIN AV6.3.C. 100V L-L, 5(10)A 115VAC, 50-60Hz AG2227 EM4-DIN AV6.3.B. 100V L-L, 5(10)A 48VAC, 50-60Hz AG2228 EM4-DIN AV6.3.A. 100V L-L, 5(10)A 24VAC, 50-60Hz AG2229 EM4-DIN AV1.3.4 / [5] 400V L-L, 20(100)A 18-60VDC [77-143VDC] AG2230 [AG2237] EM4-DIN AV0.3.4 / [5] 208V L-L, 20(100)A 18-60VDC [77-143VDC] AG2231 [AG2238] EM4-DIN AV3.3.4 / [5] 660V L-L, 20(100)A 18-60VDC [77-143VDC] AG2232 [AG2239] EM4-DIN AV5.3.4 / [5] 400V L-L, 5(10)A 18-60VDC [77-143VDC] AG2233 [AG2240] EM4-DIN AV4.3.4 / [5] 208V L-L, 5(10)A 18-60VDC [77-143VDC] AG2234 [AG2241] EM4-DIN AV7.3.4 / [5] 660V L-L, 5(10)A 18-60VDC [77-143VDC] AG2235 [AG2242] EM4-DIN AV6.3.4 / [5] 100V L-L, 5(10)A 18-60VDC [77-143VDC] AG2236 [AG2243] Available modules Type Channels Code Open collector output 2 AO2900 Relay + open coll. output 2 AO2910 Possible module combinations Type Channels Code Digital inputs 2 AQ2940 RS485 Serial Output 1 AR2950 Power supply Self p.s. Auxiliary p.s. Power supply Self p.s. Auxiliary p.s. Basic unit Slot A Slot B Slot A Slot B Basic unit Slot A Slot B Slot A Slot B Open collector output Digital inputs Relay + open coll. output RS485 Serial Output (*) (*) AV2 only Specifications are subject to change without notice EM4 DIN DS ENG 311007 5

Wiring diagrams 20(100)A model: three-phase unbalanced load Auxiliary power supply Fig. 1 Auxiliary power supply Fig. 2 Self-power supply Fig. 3 Direct connection (3-phase system + N) Direct connection (3-phase system) Direct connection (3-phase system w/out N ) 20(100)A model: three-phase unbalanced load Self-power supply Fig. 4 5(10)A model: three-phase unbalanced load Auxiliary power supply Fig. 5 Auxiliary power supply Fig. 6 Direct connection (3-phase system + N) Direct connection (3-phase system with or without neutral) CT connection (3-phase system with neutral) 5(10)A model: three-phase unbalanced load Auxiliary power supply Fig. 7 Auxiliary power supply Fig. 8 Auxiliary power supply Fig. 9 CT ARON connection (3-phase system) VT and CT ARON connection (3-phase system) VT and CT connection (3-phase system) 6 Specifications are subject to change without notice EM4 DIN DS ENG 311007

Wiring diagrams (optional modules) Open collector output VDC max 30V Fig.10 Relay + open coll. output Fig. 11 Only open collector outputs: the grounds of the outputs are separated, and therefore it s possible to carry out, for the same module, two different connections. The load resistance (Rc) must be designed so that the closed contact current is lower than 100mA; the VDC voltage must be lower than or equal to 30V. VDC: power supply voltage output. Vo+: positive output contact (open collector transistor). GND: ground output contact (open collector transistor). Digital inputs Fig. 12 Digital inputs Fig. 13 RS485 Serial output Fig. 14 PNP-NPN connections Contact and voltage connection 2 and 4-wire connection Accuracy Accuracy (RDG) depending on the current +4% Error +1.5% +1% Accuracy (RDG) depending on the current Error +4% +2.5% +2% 0% -1% -1.5% -4% PF=1 PF=L0.5 or C0.8 0,25A 1A 0.5A 2A 0,5A 2A 1A 4A 5A (Ib) 20A (Ib) 5A (Ib) 20A (Ib) 10A (Imax) 100A (Imax) 10A (Imax) 100A (Imax) EN 61036/ IEC 61036 limits (Active energy) 5(10A) Start-up current: 20mA 20(100A) Start-up current: 80mA -4% sinϕ=1 sinϕ=0.5 sinϕ=1 sinϕ=0.5 Specifications are subject to change without notice EM4 DIN DS ENG 311007 7 0% -2% -2.5% 0.1A 0.25A 1A 2A 0.25A 0.5A 2A 4A 5A (Ib) 5A (Ib) 20A (Ib) 20A (Ib) 10A (Imax) 10A (Imax) 100A (Imax) 100A (Imax) EN 61268/ IEC 61268 limits (Reactive energy) 5(6A) Start-up current: 20mA 20(100A) Start-up current: 80mA

Front panel description Keys for: 2 1. Key-pad To program configuration parameters and to display variables. S-key to enter programming and confirm selections; 4 3 1 - values programming; - function selection; - displaying the measuring pages. 2. Display LCD with alphanumeric indications to: - display configuration parameters; - display all the measured variables. 3. Removable label It shows the following information: - year of manufacturing - serial number - input voltages and currents - operating frequency - kwh measuring class - kvarh measuring class - symbols: electric system, attention and dual insulation. 4. Hidden dip-switch Enable/disable the access to the programming procedure. Dimensions and panel cut-out Terminal boards Open collector dual output module Relay output + open coll. output module RS485 Serial output module Digital inputs module AO 2900 AO 2910 AR 2950 AQ 2940 8 Specifications are subject to change without notice EM4 DIN DS ENG 311007