Domino's Take-out Pizza building kit in HO scale, latest design This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing, and self-adhesive decals. All parts fit together but may need light sanding in joints for cosmetic reasons. The model needs painting. Some model building and painting skills are required. Manufactured by Custom Cuts by Summit USA LLC, 512 Ford Street, Lake Charles, LA 70601 www.summit-customcuts.com
Assembly instructions for Domino's Pizza building Thank you for buying this Dominos' Pizza building kit. Please take some time to read these instructions before you begin assembling. This kit is milled in styrene plastic and is very easy to glue together using Plastruct Plastic Weld or similar glue products. The wall parts are tabbed and slotted for easier assembly. Take your time to identify all parts, lay them out and clean them for any burrs before gluing them together. Walls and roof Base, inside walls and counter Window frames, doors and window glazing Awnings and brackets
Facade sign and 2 small signs for the sides Street sign Assembly Start by attaching the walls to the roof as shown. The parts goes almost together, then apply the liquid glue and apply pressure to the part to make them go all the way together. Assemble the parts for the counter, fitting the slots and tabs. Mount the counter to the floor and mount the 2 wall parts.
Glue the wall pieces to the floor as shown. Glue the over-the-counter valance to the small inner roof piece. Glue the inner roof to the walls as shown. Glue the awning bracket to wall, fitting the tabs in the slots, and after the glue has set, glue on the awning. For best looking result, you may lightly sand the joints - corners and roof. If needed, fill with putty. Use a finer grit paper, 180 and finish with 6-800 until smooth. Now it is time to paint the building and the signs, see painting section. After the paint has dried, mount the side door by gluing the door support (the black piece slightly larger than the door) inside the wall, then glue on the door. Leave a 0.04" lip to make room for the floor.
Mount the window glazing inside the wall, leaving a 0.04" lip on the bottom of the tall front and side windows (to leave room for the floor). Remove the "filling" inside the window frames and cut/file away the burrs, then Install the window frames, this is a press fit so you do not need to glue them in. If you want to glue them in place, use Crystal Clear or a similar liquid glass product. Glue the sign parts on both sides of the sign base as shown (laminate). Painting For best results, give the building and the signs a coat of primer first. Paint the whole building dark tan. On this model I used. Mask off the tan and paint the bottom of the wall dark brown. Paint the side of the facade sign blue, I brush painted Humbrol #14. Mask off the sign faces and paint the street sign Aluminum or light gray. Paint the awnings and brackets a bright red. Before handling the decal sheet, I strongly recommend you seal it with a coat of Krylon Crystal Clear acrylic coating or Testors Dull Cote. Uncoated, you have a risk of rubbing off some of the print when handling it.
Cut the decals with a sharp hobby knife or a pair of scissors. Remove the backing paper using the tip of the knife to separate it from the decal. Cutting out the individual logo letters gets the best result, but you could also just paint the letters. Peel the off the backing paper in one corner, fold it back 1/4". Align the decal and then attach the corner. Peel off the rest of the backing paper to attach the rest of the decal. Mount the decals on the signs using the same method. Mount the decals on the inside walls as shown on the picture below. Finishing Mount the signs on the wall using a tiny amount of Woodland Scenics Scenic Cement or white glue. These glues will let you move the sign until it sits right. If you want to detail the roof with vents and airconditioners, we recommend Walthers #933-3733 Roof Details Kit. Enjoy your Domino's Pizza on your layout. Here are some other products you may enjoy in a future project:
#SMFS Summit Motel, full version #TB-001 Taco Bell Restaurant #EX-001 Exxon Gas Station & Store #DP-001 Domino's Pizza take-out #TB-003 New Taco Bell Restaurant #SW-001 Subway Restaurant #CS-001 Dave's Coffee Shop #KFC-001 KFC Restaurant #WH-001 Waffle House Restaurant #SC-001 Rural Shamrock Gas Station #SH-001 Shell Gas Station & Store #DG-001 Dollar General Store #LO-001 #CVS-001 CVS Pharmacy #FS-001 Modern City Fire Station #ML-001 Strip Mall backdrop #1 #ML-002 Strip Mall backdrop #2 Lowe's backdrop building #JL-001 Jiffy Lube
Mall complex #ML-003 Office Depot backdrop #ML-005 Pier 1 Imports backdrop #ML-006 Dollar Tree backdrop #CH-001 Polk County Court House #BK-001 First State Bank #GS-001 Gas Station backdrop #HD-001 Harcdee s Restaurant #AM-001 Small Amtrak Station #DA-001 Discount Auto Parts #CJ-001 Carl s Jr. Restaurant #PH-001 Pizza Hut Restaurant Keep updated for new products on our website: www.summit-customcuts.com #DP-004 MKT Depot