ACME 50 Application Guide p1
CONTENTS Features & Benefits... 2 Product Images... 3-8 TRIM AND CONNECTORS Trim & Connector Diagram.... 9 Partition Profile Section... 10 Adjustability.... 11 Ceiling & Floor Track... 12 Typical Drawing Package... 13 Wall Start Condition... 14 Finished End Condition... 15 Corner Condition.... 16 3 Way T Condition... 17 Bypass Panel... 18 Butt-Joint Condition.... 19 Angular Condition... 20 DOORS AND FRAMES Hinged Doors... 21-22 Pivot Doors... 23 Sliding Doors... 24 Full Height Frames... 25 Door Details.... 26-28 Hardware.... 29 Typical Applications... 30-31 Specification Check List... 32 p1
INTRODUCTION Acme 50 is a clean, seamless glass wall with a modern, slim aesthetic. It encloses space while maximizing daylight in workspaces. Acme 50 blends harmoniously with the surrounding architecture. Ideally suited for office front applications, its minimalist aesthetic can enhance any corporate, creative or architectural environment. Acme 50 can be specified with many combinations of specialty glass, frame colors, and a variety of door and hardware options. Acme 50 allows 1 of adjustability within the slim 1 1 /2 profile. Levelers are concealed within the bottom rails and spaced every 18 to ensure a stable platform to support the glass panels. Manufactured using glass and 18 gauge steel, it is an eco-friendly choice. FEATURES & BENEFITS: 1½ high by 2½ deep minimalist profile 1 of total adjustability (helps to eliminate costly flash patching and feathering) Framed glass door options with matching 1½ stiles and rails are available in sliding, hinged and pivot configurations Frameless swinging glass doors Full or half-height locking door pulls Finish options include powder-coated steel, textured paints, and glazing to accommodate a variety of aesthetic choices Available with either 3 /8 or ½ thick glass Utilizes US hardware and cylinders to be compatible with existing master key systems Only framed glass door on the market that accepts full size commercial mortise lock, such as the Corbin ML2000 36-39 STC rating for glass panels Acme 50 can contribute points toward LEED projects Manufactured within 500 miles of projects in Chicago, Boston, New York and Washington DC High recycled steel and glass content FSC Certified wood doors p2
Minimalist design is highlighted by post-less corner conditions and framed sliding doors. Graduated specialty glass creates a sense a privacy while maximizing the exposure to natural light. p3
p4 An endless variety of veneer door options are available to meet the designers requirements and budget.
The integrated lock box of the fully framed door accommodates any heavy-duty US commercial lockset. Satin Etched Glass balances privacy with translucency. p5
p6 For maximum privacy, glass can be nearly opaque.
Acme 50 easily integrates with millwork walls. Clerestory windows allow light into the space while adding privacy. p7
p8 3 Way T condition allows small offices or spaces to feel larger and more open.
TRIM & CONNECTORS TRIM & CONNECTOR DIAGRAM FULL LITE SLIDING DOOR WITH PULL THRU GLASS (SINGLE) TOP CHANNEL WITH CEILING TRACK WALL POST WITH WALL TRACK BUTT-GLAZED CORNER BOTTOM CHANNEL WITH FLOOR TRACK BUTT-GLAZED JOINT FULL-LITE DOOR WITH LOCK BOX (AVAILABLE AS HINGED OR PIVOT) FULL LITE SLIDING DOORS WITH PULL THRU GLASS FINISHED END 3 WAY T CONDITION p9
PROFILES PARTITION PROFILE SECTION CEILING LINE 1 1 /2 5 /8 DAYLITE SIZE POST HEIGHT CEILING HEIGHT 1 1 /2 5 /8 FINISHED FLOOR LINE p10
ADJUSTABILITY IDEAL FLOOR LOW POINT OF FLOOR REVEAL - VARIES 2 1 /2 2 1 /2 5 /8 1 1 1 /2 FIN. FLOOR LINE MIN. VAR UP TO 1 HIGH RECOMMENDED LIGHT & SOUND SEAL (TYP) LIGHT & SOUND SEAL (TYP) Notes: Concealed levelers in the base allow for over 1 of height adjustability to varying floor conditions. p11
TRIM & CONNECTORS CEILING TRACK Recessed ceiling channel is manufactured of 18 gauge steel, 1 deep, recessed from panel face. The ceiling channel is provided with continuous light and sound seal at the ceiling and can be attached to the ceiling grid by means of non-damaging clips or screwed through a drywall ceiling or soffit. 5 /8 CEILING LINE DAYLITE SIZE POST HEIGHT CEILING HEIGHT 1 1 /2 FLOOR TRACK The floor channel is manufactured of 18 gauge steel. Acme 50 can be installed either before carpet is installed or on top of carpet. The system can also be installed on top of VCT tile, stone or other hard surfaces. The floor channel is attached by either nailing into the floor or with screws (for finished floor applications). 1 1 /2 FINISHED FLOOR LINE 5 /8 p12
TYPICAL DRAWING PACKAGE A typical drawing package will include a floor plan, sections details, and elevations. A glass legend will be supplied along with an other information that pertains for the project. BLOCKING BY OTHERS BLOCKING BY OTHERS 5 6 1 / 2 MUST HOLD F F DET. 1 DET. 5 A27/D26 361 DET. 6 8 5[ CEILING HEIGHT (MUST HOLD) 100\ POST HEIGHT 97\ DAYLITE WOOD DOOR (B/O) 8-4_ JAMB OPENING HEIGHT FIN. FLOOR MAY VARY FROM } TO 1\ IF FLOOR NOT BEING LEVEL. SECTION 1 ALL/GL PARTITION TYPE A SECTION 2 SWING WOOD DOOR UNIT 1 2 URETHANE SEAL 26 PANEL DAYLITE 5-6 (MUST HOLD) 36 JAMB OPENING WIDTH 35 3 /4 DOOR WIDTH GL-1 38 TO CL OF LEVER ALIGN ALIGN ELEVATION 1 GLASS LEGEND GL-1 = 1/2 THK. CLEAR TEMPERED 27 PANEL SIZE 37 1 /2 DOOR UNIT SIZE DETAIL 1 DETAIL 5 DETAIL 6 CORRIDORE SIZE p13
TRIM & CONNECTORS WALL POST CONDITION Wall start posts are available in heights of 96-120. Finished in a matching powder coat painted finish. Wall start condition can also be a door jamb. LIGHT & SOUND SEAL (TYP) PANEL DAYLITE 3 / 8 OR 1 / 2 THK. GLASS Note: Wall posts run floor to ceiling. 2 1 /2 1 1 / 4 3 / 4 PANEL SIZE TOP CHANNEL WITH CEILING TRACK WALL POST WITH WALL TRACK BOTTOM CHANNEL WITH CEILING TRACK p14
TRIM & CONNECTORS FINISHED END CONDITION 3 / 4 PANEL SIZE Finished end posts are available in heights of 96-120. Finished in a matching powder coat painted finish. Note: Finished end posts runs floor to ceiling. 2 1 /2 1 1 / 2 PANEL DAYLITE TOP CHANNEL WITH CEILING TRACK FINISHED END POST BOTTOM CHANNEL WITH CEILING TRACK p15
TRIM & CONNECTORS CORNER CONDITION Our unique Butt Glazed Seamless Corner has a post-less butt glazed design. Available in heights of 96-120 and widths up to 120. Finished in a matching powder coat painted finish. PANEL LAYOUT DIMENSION PANEL DAYLITE 2 1 / 2 1 / 8 GLASS BUTT JOINT, POLISHED EDGES AT GLASS, CLEAR SEALANT 2 1 /2 TOP CHANNEL WITH CEILING TRACK PANEL LAYOUT DIMENSION PANEL DAYLITE BUTT GLAZED CORNER BOTTOM CHANNEL WITH CEILING TRACK p16
TRIM & CONNECTORS 3 WAY T CORNER CONDITION Our unique 3 Way T condition welded seamless condition has a post-less butt glazed design. Available in heights of 96-120 and LIGHT & SOUND SEAL (TYP) widths up to 120. Finished in a matching powder coat painted finish. PANEL SIZE 1 /2 DAYLITE SIZE 1 1 /2 1 1 /4 BUTT JOINT WITH SILICONE TOP CHANNEL WITH CEILING TRACK BUTT GLAZED 3 WAY T CONDITION BOTTOM CHANNEL WITH CEILING TRACK p17
TRIM & CONNECTORS BYPASS PANEL One of several options to transition between offices, our bypass panels are made of 18 gauge steel. Available in heights of 96-120 and widths up to 120. Finished in a matching powder coat painted finish. 3 / 8 OR 1 / 2 THK. GLASS ROOM SIDE LIGHT & SOUND SEAL (TYP) ROOM SIDE DAYLITE 3 1 / 4 3 1 / 4 DAYLITE 1 1 / 2 1 / 2 1 / 2 1 1 / 2 3 / 8 OR 1 / 2 THK. GLASS Note: Bypass panels run floor to ceiling. 2 1 /2 2 1 /2 1 1 1 5 / 8 1 5 / 8 TOP CHANNEL WITH CEILING TRACK DRYWALL PARTITION FLUSH BYPASS PANEL BOTTOM CHANNEL WITH CEILING TRACK p18
TRIM & CONNECTORS BUTT-JOINT CONDITION Butt-Joint Condition has (2) pieces of glass meeting end-to-end with 1 /8 clear silicone joint. 1 / 8 CLEAR SILICONE GLASS BUTT-JOINT Note: Butt-Joint conditions are used in any panel runs, keeping single glass panel widths under 48 maximum. 2 1 /2 3 / 8 OR 1 / 2 THICK GLASS TOP CHANNEL WITH CEILING TRACK BUTT-JOINT BOTTOM CHANNEL WITH CEILING TRACK p19
TRIM & CONNECTORS ANGULAR CONDITION Angular condition has mitered, angled, floor tracks, base plinths, and ceiling track with angle-cut glass ends and 1 /8 clear silicone joint. 1 / 8 CLEAR SILICONE GLASS BUTT JOINT PANEL SIZE 2 1 /2 134 TOP CHANNEL WITH CEILING TRACK BUTT-GLAZED ANGULAR CONDITION BOTTOM CHANNEL WITH CEILING TRACK p20
DOORS & FRAMES DOOR OPTIONS - HINGED 1¾ hinged flush metal doors 84-108 height options, 36 unit width Single & pair option available Powder coated to match frame McKinney TA2714 hinges standard Note: Can accept a cylindrical and Mortise lockset. Available in a single or pair configuration. 1¾ hinged flush wood doors 84-108 height options, 36 unit width Laminate, Natural Veneer, Composite Veneer finish option Single & pair option available McKinney TA2714 hinges standard Note: Can accept a cylindrical and Mortise lockset. Available in a single or pair configuration. 1¾ Hinged Framed Glass Door with Mortise Lockbox 84-120 Height Options, 36 Unit Width Single & Pair Option Available Door Frame Shall Be Powder Coated 3 /8 or ½ Clear Tempered Glass Standard McKinney TA2714 hinges standard Tempered Glass Only in Lock Box Doors Note: Corbin Russwin ML2000 standard, but compatible with any ANSI Standard Mortise or Cylindrical lockset. Available in a single or pair configuration. p21
DOORS & FRAMES DOOR OPTIONS - HINGED 3 /8 Clear Tempered Frameless Glass Hinged Doors 84-120 height options, 36 unit width Single option only Casma 13100.611 hinges standard Note: Frameless glass door hardware included using Casma Lockset or passage set with hinges. This is the only hardware that can be applied to this door. p22
DOORS & FRAMES DOOR OPTIONS - PIVOT 1¾ Offset Pivot Flush Metal Doors 84-108 height options, 36 unit width Single only available Powder coated to match frame Rixson 117-3/4 offset pivot standard Note: Can accept a cylindrical and Mortise lockset. Available in a single or pair configuration. 1¾ Offset Pivot Flush Wood Doors 84-108 height options, 36 unit width Laminate, Natural Veneer, Composite Veneer finish option Single only available Rixson 117-3/4 offset pivot standard Note: Can accept a cylindrical and Mortise lockset. Available in a single or pair configuration. 1 ¾ Offset Pivot Framed Glass Door with Mortise lock box 84-120 height options, 36 unit width Single only available Powder Coated to match frame 3 /8 & ½ Clear Tempered Glass Standard Rixson 117-3/4 offset pivot standard Tempered glass only in lock box doors Note: Corbin ML2000 standard, but compatible with any US Commercial Mortise lockset. Also Available in a single or pair configuration. p23
DOORS & FRAMES DOOR OPTION - SLIDING 1¾ Sliding Full Lite door 84-120 height options, 40¾ unit width Single & pair option Door framing is powder coated 3 /8 Clear Tempered Glass Standard, ½ Glass not available in sliding doors Note: Sliding doors includes using a pull, track and deadbolt, if locking requirement requested. Note: Before using sliding doors on your project, please confirm with city codes the use of sliding doors as an only way of egress from smaller offices or conferences rooms. Certain cities ban the use of sliding doors. p24
DOORS & FRAMES FRAMES HINGED Full Height Door Frames. Single unit width available in 36 width. Pair unit width available in 72 width. Available in heights 84-120 full height frames. Only lock box doors and frameless glass doors can be used for heights greater than 108. PIVOT Single unit width available in 36 width. Pair units are not available Available in heights 84-120 full height frames. Only lock box doors can be used for heights greater than 108. SLIDING DOOR Frames for 1¾ doors. Single unit width available in 37 3 /4 width. Pair unit width available in 78 5 /8 width. Available in heights 84-120. Full height frames. Door locks are supplied in the door jambs for locking doors and must use an interchangeable core. p25
DOORS & FRAMES FULL HEIGHT HINGED DOOR DETAILS LIGHT & SOUND SEAL (TYPICAL) CEILING LINE 1 1 /2 1 1 /2 1 5 /8 1 3 / 4 2 1 / 2 DAYLITE SIZE JAMB OPENING HT. 1 3 / 4 1 1 /2 FIN. FLOOR LINE 5 /8+ PANEL DAYLITE 1 1 / 8 3-0 JAMB OPENING WIDTH 2-11 3 / 4 DOOR WIDTH 1 / 8 1 PANEL DAYLITE 1 1 / 2 2-8 3 / 4 DAYLITE 1 1 / 2 MORTISE LOCK 2 1 /2 1 3 /4 2 1 /2 PANEL SIZE 3-0 1 / 2 DOOR UNIT SIZE PANEL SIZE p26
DOORS & FRAMES FULL HEIGHT PIVOT DOOR DETAILS CEILING LINE LIGHT & SOUND SEAL (TYPICAL) 1 /8 1 1 /2 1 1 /2 5 /8 DOOR STOP 1 3 / 4 2 1 / 2 DAYLITE SIZE JAMB OPENING HT. 1 3 / 4 5 /8+ 1 1 /2 CENTER HUNG PIVOT 3-0 JAMB OPENING WIDTH PANEL DAYLITE 1 1 / 1 8 2-1 3 / 4 DOOR WIDTH / 8 1 PANEL DAYLITE 1 / 2 2-8 3 / 4 DAYLITE 1 / 2 MORTISE LOCK OFFSET PIVOT 2 1 /2 1 3 /4 1-0 3 / 8 PANEL SIZE 3-0 1 / 2 DOOR UNIT SIZE PANEL SIZE p27
DOORS & FRAMES FULL HEIGHT SLIDING DOOR DETAILS CEILING LINE LIGHT & SOUND SEAL (TYPICAL) SLIDING TRACK 1 1 /2 5 /8 2 1 / 2 1 3 / 4 DAYLITE SIZE JAMB OPENING HEIGHT 1 3 / 4 1 1 /2 FIN. FLOOR LINE 5 /8+ ROOM SIZE STRIKE WITH SEAL AT DOOR STILE 3-4 3 / 4 NET DOOR WIDTH 1 / 2 3-1 3 / 4 DAYLITE 1 / 2 1 3 /4 LIGHT & SOUND SEAL TYPICAL 2 1 /2 PULLS (TBD) 2 1 /2 LOCK AT PARTITION POST (MUST USE INTERCHANGEABLE CORE 3-1 3 / 4 TRIM OPENING 3-3 3 / 4 DOOR UNIT SIZE 1 1 / 4 p28
DOORS & FRAMES HARDWARE Corbin Russwin Mortise Lockset ML2051 Corbin Russwin Mortise Passage Latchset ML2010 Corbin Russwin Heavy Duty Cylindrical Lock CL3351 * Corbin Russwin Heavy Duty Cylindrical Latch CL3310 * Flush Metal Hinged Doors O O O S O O O O Flush Wood Hinged Doors O O O S O O O O Framed Glass Hinged Doors Framed Glass Hinged Doors w/lockbox Frameless Glass Hinged Doors O S Adams Rite MS1850S Casma 1512 Passage Set Casma 1500.611 Lockset Rockwood 51 Pull RM3301 Rockwood 72 Pull RM3301 Rockwood 51 Pull LP3301DBD Rockwood 72 PullLP3301DBD S O O O S O O O O O Flush Metal Pivot Doors O O O S O O O O Flush Wood Pivot Doors O O O S O O O O Framed Glass Pivot Doors S 0 0 0 Framed Glass Pivot Doors w/lockbox O S Framed Glass Sliding Doors O S O O O S = Standard; O = Option * Must specify interchangeable core cylinder ** Ives RL30 Roller Latch standard with non-locking pulls p29
TYPICAL APPLICATIONS SINGLE APPLICATIONS-DRYWALL TO DRYWALL Single Office Front Single Conference Room Front p30
TYPICAL APPLICATIONS TWO OFFICE CONFIGURATION Two Office Configuration with Bypass Panel Two Office Configuration Frameless Glass Corners and 3 Way T Glass Condition p31
ACME 50 SPECIFICATION CHECK LIST QUOTATION/DRAWING CHECK [ ] All Glass/Door Frames/Door counts can be found on drawing and quote [ ] Door Type and Finishes are noted on drawing and priced in quote [ ] Connections (Corners, 3 Way, Finished Ends, and angle conditions) can be found on drawings and quote [ ] Correct ceiling height is called out on drawing [ ] Elevations match partition layout in floor plan and elevations show ceiling height [ ] Door hardware is priced in quote and noted on drawing [ ] Door hardware schedule is supplied (if required) [ ] Any specials are noted on drawings and quoted with lead time and SPA# [ ] Building Conditions are shown on drawing and priced in quote [ ] Angular Panel dimensions and degree of angle is shown in drawing [ ] Glass types, description and thickness are called out on drawing and quote [ ] Special glass is called on drawings and priced in quote [ ] Clear tempered mark will be supplied unless otherwise specified [ ] Field measurements must include ceiling heights at each door frame [ ] Keying and Master keying specifications are included p32
67 Toll Road Holland Landing, Ontario L9N 1H2 T 905.836.7676 F 905.836.6000 inscapesolutions.com