room essentials 4 Drawer dresser w/ door DPCI # 249-05-0418 (Black Woodgrain) DPCI # 249-05-0419 (Virginia Walnut) >> assembly instructions 92380 Video instruction as Help to assembly, scan the QR code and see the video. 1
FREE! Do not go back to your store! we will help you! Missing or Damage Parts? Have Questions about Assembly? The store where you made this purchase does not stock parts for this item. If you needs parts (damaged or missing) or have questions about assembly, please call our toll free support line. All orders normally ship within 24 hours. Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling. 2
Congratulations on your latest Target purchase Don't start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you'll be on your way to transforming your room in no time. Good luck - though we're confident you won't need it. before you begin 3. 4. Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference DPCI # 249-05-0418 (Black Woodgrain) DPCI # 249-05-0419 (Virginia Walnut) Use the carton as a worksurface to prevent product damage during assembly. Gather all tools prior to assembly. Two people are required for assembly. tools needed 3
table of contents customer service information introduction parts list hardware how to use the cam lock system assembly adjustment of hinge specification sheet information sheet 2 3 5 6-7 8 9-32 33 34 35 QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling. 4
ITEM DESCRIPTION QUANTITY 00590 right drawer side 4 00591 03087 left drawer side drawer back 4 4 L 06294 drawer bottom 4 E back panel drawer front 2 4 F left end panel 1 G H divider panel right end panel 1 1 T I L bottom panel top panel 1 1 W F T shelf 2 G W door left 1 T H 03087 00591 I 06294 00590 E 5
hardware 11042 20203 20228 23006 23010 25215 25233 x8 x12 x24 25 pcs x2 x11 x6 x8 shelf pin dowel pin drawer fastener nails large head nails short flat head screw flat head screw 26234 25502 26040 26228 31570 25610 x5 x16 x18 x5 x18 x2 long feet screw drawer screw short screw handle screw cam bolt connector bolt 31683 32205 10601 10901 50505 81009 91405 96203 x18 x5 x2 x1 x3 x5 x2 x2 cam short feet screw garment rod holder cover hinge handle L-plate stopper 6
hardware 52114 65806 41649 72501 94072 x3 x5 x4 x1 x1 door hinge rectangular foot 88060 94073 97642 x1 x2 x1 Warning label wall attachment strip hex wrench drawer glide garment rod stabilizer 7
how to use the cam lock system 1 2 3 CORRECT NOT CORRECT 180 4 5 6 8
step 1 case assembly - insert cams and dowel pins CORRECT NOT CORRECT finished front edge I finished front edge L finished front edge G 20203 x12 31683 x10 Arrow dowel pin cam Place the cams into the large holes on G, L and I, so that the arrow is facing the edge of the panel. Insert dowel pins into the small outer holes on the ends of the G,L and I. 9
step 2 case assembly - insert hinges F finished front edge 50505 x3 hinge 3. Divide hinge by loosening the screw and split hinge part from each other. Place hinge into the correct holes on the left end panel. Tighten screws but do not over tighten. 10
step 3 case assembly - insert cam bolt finished front edge finished front edge H finished front edge I 31570 x10 32205 x5 finished front edge F L cam bolt short feet screw Screw cam bolts into the panels F, L and H, cam bolts must be screwed down. Tab short feet screw into panel I with a hammer. 11
step 4 case assembly - attach drawer glides flat head screw drawer glide screw drawer glide screw 25233 x8 26040 x16 41649 x4 H flat head screw drawer glide screw drawer glide G 3. Place drawer glider screws and flat head screw through the correct holes on the drawer slide into the holes on the panels G + H. Tighten screws but do not over tighten. Repeat this step for each of the remaining glides. 12
step 5 case assembly - insert garment rod holder finished front edge G F 25215 x2 10601 x2 finished front edge short flat head screw garment rod holder Screw the garment rod holder into the panels using short flat head screws. 13
step 6 case assembly - attach top panel and bottom panel to divider panel 25610 97642 L x2 x1 finished front edge G finished front edge 3. connector bolt hex wrench Place the cam bolts from top panel L into the holes on the divider panel G. Tighten cams. Use the hex wrench to install connector bolts into I and divivider panel G. finished front edge I 14
step 7 case assembly - attach left and right panel F finished front edge L G finished front edge H finished front edge I finished front edge Place the cam bolts from left and right end panels F and H into the holes on the top and bottom panels L and I. Tighten cams. 15
step 8 case assembly - attach L-plates L H 25215 x4 91405 x2 G short flat head screw L-plate I F finished front edge Use short flat head screw to attach L-plate to the right end panel H and in alignment with top panel L, place in center. Use short flat head screw to attach L-plate to the left end panel F and in alignment with top panel L, place in center. 16
step 9 case assembly - attach rectangular feet H L G 26234 x5 65806 x5 I F long feet screw rectangular foot Place rectangular feet 65806 into the holes on the bottom panels I. Place the screws 26234 through holes and gently screw them onto the bottom panel. Make sure to fasten the screws together with short feet screw 32205, but be careful not to over tighten. 17
step 10 case assembly - attach back panels 1 unfinished side 2 unfinished side I H I 23006 x2 23010 x11 90 25 pcs large head nails 3 nails H 3. 4. Tab 2 of the large head nails 23010 into the centre of back edge of divider panel G. ONLY HALF WAY IN. Slide the back panels up (unfinished side up) against the nails and hold smooth with bottom panel I. Attach one nail 23006 in each corner. Attach the rest of nails 23006 all the way arround the edges and 9 pcs 23010 into divider panel G. I 18
step 11 case assembly - mount safety wall attachment strips 1 2 3 1 1/5" IMPORTANT. The screw supplied together with the wall attachment strip is to be used only for fixing the wall attachment strip to the furniture. In addition to this, you vill need to choose a screw or fitting which is suitable for securing the bracket to the kind of walls you have. If you are unsure about what type of screw to usee contact your local handware store. Wall attachment strip are required to be installed. 94073 x2 L F wall attachment strip G H 3. Place the dresser in the desired position against the wall. Mark the locations of the TWO wall attachment SLOTS at the top of the DRESSER. MEASURE down 1 1/5" from the mark at the top of the case and attach the two wall STRIPS with washers and screws. Note - The washers and screws for wall attachment should be purchased from a hardware store to suit the type of wall. Pass the wall attachment strips through the slots at the top back of the case, and attach them to the underside of the DRESSER top with the screws and washers that are included in the PACK. I 19
step 12 case assembly - attach stabilizer L H 26040 x2 94072 x1 F G short screw I stabilizer 3. Place the stabilizer 94702 in between divider panel G and right end panel H. Place the short screw 26040 through the holes of 94702 and gently screw them into the panels G and H. Tighten screws but do not over tighten. 20
step 13 case assembly - install shelves and cover L T x2 H G 10901 x1 11042 x8 F T shelf pin I cover 3. 4. Fix cover to the top panel L to cover the cam holes. Insert shelf pin 11042 in right end panel F and divider panel G. Place shelves T into the case assembly as shown. Press shelves T down onto the shelf pin. 21
step14 case assembly - install garment rod L T H 72501 x1 F G T I IMPORTANT. When using garment rod - Place Shelves T in bottom. garment rod Attach garment rod 72501 into garment rod holder assembled in between left end panel F and divider panel G. 22
step 15 case assembly - install door hinge 52114 x3 W door hinge Insert door hinge into the holes on the door W. Tighten screws but do not over tighten. 23
step 16 case assembly - attach door L T F G W T H I 3. 4. Align the holes in hinge and door hinge. Move the door W to perfectly assemble with left end panel F. Tighten screws but do not over tighten. Ajustment of door, see page 33. 24
step 17 case assembly - attach handle to door and stop to divider panel L T F G T H 26228 81009 96203 W x1 x1 x2 I handle screw handle stopper Use the handle screw 26228 to attach the handle 81009 to the door W. Attach stops 96203 to the divider panel G. 25
step 18 drawer assembly - insert cams and cam bolts CORRECT NOT CORRECT 31683 x8 31570 x8 00591 00590 cam cam bolt E Insert cams 31683 in the large holes on the face of each drawer side. Make sure the arrow on the cam is pointed toward the edge of the drawer side as shown in the detail at left. Screw 2 cam bolts 31570 into each drawer front E. x4 26
step 19 drawer assembly - attach drawer sides to drawer back 03087 00590 20228 x24 00591 drawer fastener Align holes at back of the drawer sides, 00590 and 00591 with the holes on the drawer back 03087. Make sure the groove on the drawer back is facing the inside of the drawer. Tap drawer fasteners into place with a hammer. Repeat these steps for all 4 drawers. 27
step 20 drawer assembly - attach drawer bottom 03087 00590 00591 06294 finished side up 3. Press the drawer bottom 06294 (with the finished side up) into the grooves on drawer sides 00590, 00591and the back 03087. Paper overlays the groove, but it has a slit so drawer bottom inserts well. Repeat these steps for all 4 drawers. 28
step 21 drawer assembly - attach drawer front 03087 00590 06294 00591 E 3. 4. Place the cam bolts that are attached to the drawer front E into the holes on the drawer sides. Make sure the drawer bottom is completely inserted into the grooves in the drawer front and back. Tighten cams. Repeat these steps for all 4 drawers. 29
step 22 drawer assembly - attach handle to drawer front 26228 x4 81009 x4 E 00591 06294 handle screw handle 00590 03087 Use the handle screw 26228 to attach the handle 81009 to the drawer front E. Repeat these steps for all 4 drawers. 30
step 23 drawer assembly - attach drawer glides 25502 x16 41649 x4 06294 drawer screw E 00591 03087 drawer glide 3. 4. Place drawer glide on bottom of drawer side and slide forward against drawer front E. Insert drawer glide screws through the hole in the drawer glide and into the drawer side plates. Tighten screws but do not over tighten. Repeat these steps for all 4 drawers. 31
step 24 case assembly - install drawers into case assembly and warning label on top panel L E 88060 x1 F W E E E Warning label 3. Angle the drawer assembly so that the wheels are inserted into the drawer glides on divider panel G and right end panel H. Slide drawer assembly over the drawer glides on divider panel G and right end panel H. Apply warning label 88060 inside top drawer. 32
3. 3. 3. 08799998-50 33
specification sheet 3 YEAR WARRANTY: All Tvilum furniture is warranted to the original purchaser at the time of purchase and for 3 years after the purchase date. We warrant to you, the original purchaser, that our furniture and all furniture parts and components are free of defects in material or workmanship. The word defects as used in this warranty is defined as any imperfections which impair the use of the furniture. Our warranty is expressly limited to the replacement or repair of furniture parts and components and Tvilum will have a reasonable amount of time to remedy said defect. This warranty applies under conditions of normal use. The warranty does not cover defects caused by improper assembly or disassembly defects occurring after purchase due to intentional damage, product modifications, exposure to the elements, accidents, misuse, abuse or negligence and labor or assembly costs. All implied warranties, including the warranty of merchantability shall not extend beyond the duration of the written warranty stated above. Tvilum liability is expressly limited to the costs of material for repair or replacement of defective goods and in no event will Tvilum be liable for incidental or consequential damages resulting from use of the product. Some states do not allow limitations on how long an implied warranty may last or the exclusions or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you. 10 kg 22 lbs 15 kg 33 lbs This warranty gives you specific legal rights which may vary from state to state. max. Any claims made under this warranty must be presented in writing to: Tvilum 2195 Philpott Road South Boston, VA 24592 5 kg 11 lbs 34
Read more at www.tvilum.com THIS PRODUCT will ensure you A product tested for harmful substances Helps to maintain healthy indoor climate Wood from sustainable forestry The furniture is PEFC-certified Safe furniture for use in your home The furniture has been safety tested and approved Minimum 25% post consumer recycled materials 35
36