room essentials 4 drawer chest DPCI # 249-05 - 0103 (Black Woodgrain) DPCI # 249-05 - 0106 (Espresso) >> assembly instructions 92335 H 1
FREE! Do not go back to your store! we will help you! Missing or Damage Parts? Have Questions about Assembly? The store where you made this purchase does not stock parts for this item. If you needs parts (damaged or missing) or have questions about assembly, please call our toll free support line. All orders normally ship within 24 hours. Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling. 2
Congratulations on your latest Target purchase Don't start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you'll be on your way to transforming your room in no time. Good luck - though we're confident you won't need it. before you begin Check for damaged or missing parts. Please call 1-855-MYTGTHOME (855-698-4846) for parts and service. Please reference DPCI# 249-05 - 0103 (Black Woodgrain) 249-05 - 0106 (Espresso) 2. Use the carton as a worksurface to prevent product damage during assembly. 3. Gather all tools prior to assembly. 4. Two people are required for assembly. tools needed 3
table of contents customer service information introduction parts list hardware how to use the cam lock system assembly specification sheet information sheet products available 2 3 5 6-7 8 9-29 30 31 32 QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI# number ready when calling. 4
ITEM DESCRIPTION QUANTITY 00470 right drawer side 4 00471 left drawer side 4 S 03077 drawer back 4 07531 drawer bottom 4 S S back panel 2 LA EA drawer front 4 ID bottom panel 1 LA top panel 1 PA top rail 1 PA PB rail 4 FC HC left end panel right end panel 1 1 FC PB 00471 03077 PB HC PB EA 07531 ID 00470 PB 5
hardware 10401 12754 13414 20209 20228 x28 x4 x2 x26 x16 panel clips rectangular foot corner bracket dowel pin drawer fastener 21812 25233 25241 25266 x24 x4 x8 x2 flat head screw spacer short flat head screw long flat head screw 26027 26214 31685 31686 x24 x8 x8 x8 1/4" screw machine screw small cam large cam 6
hardware 31570 41404 88060 94073 x16 x8 x1 x2 cam bolt wall attachment strip drawer tip warning label drawer glide 7
how to use the cam lock system 1 2 3 CORRECT NOT CORRECT 180 4 5 6 8
step 1 drawer assembly - attach drawer bottom to back 03077 07531 paper x 4 2. Press the drawer bottom (with the finished side up) into the grooves on the drawer back. Paper overlays the slot, but it has a slit so drawer bottom inserts well. 9
step 2 drawer assembly - attach drawersides 00470 07531 20228 00471 x 4 x16 drawer fastener 2. Press the grooves on the drawer sides onto the drawer bottom (with the finished side up). Use a small hammer to nail the drawer sides to the drawers back (use drawer 4x fastener for each drawer). 10
step 3 drawer assembly - insert cam bolts EA 31570 x 4 x8 drawer front cam bolt Screw cam bolts into the drawer front. Cam bolts must be screwed down flush. 11
step 4 drawer assembly - attach drawer front and insert drawer cams 88060 NOT CORRECT 00470 CORRECT 03077 07531 31685 88060 finish side up x8 x1 EA small cam 00471 x 4 2. 3. 4. Place cams in large holes so that the arrow on cam faces the edge of the panel. Place the cam bolts that are attached to the drawer front into the holes on the drawer sides. Make sure the drawer bottom is completely inserted into the grooves and tighten the cams. (look at page 8 for help if needed). Apply drawer tip warning label to the inside of the top drawer. 12
step 5 drawer assembly - attach panel clips 00470 EA 10" 10" 07531 10401 03077 x16 00471 x 4 panel clips 2. Place back panel clips as shown and press the thin tabs between the back panel and the groove. Tighten the screws but be careful not to over tighten. 13
step 6 case assembly - insert dowel pins PA PB 20209 x4 x18 dowel pin Press dowel pins into the holes at the end of the 4 rails (PB) and on the top side of the rail (PA) as shown on the picture. 14
step 7 case assembly - insert dowel pins, cams and corner bracket ID PB x1 13414 x2 20209 x4 25233 x2 31686 x4 corner bracket dowel pin short flat head screw large cam 2. 3. Press the dowel pins into the large holes at the end of the top (ID). Put large cams into the 4 holes on the downside of the top (ID) and make sure the the arrow on the cam is toward the edge. Screw corner bracket on to one of the rails (PB) as shown on the picture. 15
step 8 case assembly - insert cams and dowel pins CORRECT NOT CORRECT 20209 x2 31686 x2 31570 x2 FC dowel pin large cam cam bolt 2. 3. Tap the dowel pins into the larger holes at the top edge of the left end panel. Place the large cam into the holes on the left end panel. Screw the cam bolts into the small holes (inner holes)at the bottom of the left end panel. Cam bolts must be screwed down flush. 16
step 9 case assembly - attach drawer glides. front of glide front screw location back screw location top / haut back FC 21812 26027 41404 front (finished edge) x12 x12 x4 bottom spacer 1/4" screw Fully extend drawer glides to the front. 2. Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide, then through the spacers and into the holes on the panel. 3. Tighten screws but do not over tighten. drawer glide 4. Close slide until the front hole is visible through the oval slot on the glide. 5. Place 1/4" screws through the hole in the slot and through the spacer. 6. Tighten screw but do not over tighten. 17
step 10 case assembly - insert cams and dowel pins CORRECT NOT CORRECT HC 20209 x2 31686 x2 31570 x2 dowel pin large cam cam bolt 2. 3. Tap the dowel pins into the larger holes at the top and bottom edges of the right end panel Place the large cam into the holes on the right end panel. Screw the cam bolts into the small holes (inner holes) at the bottom of the left end panel. Cam bolts must be screwed down flush. 18
step 11 case assembly - attach drawer glides back screw location front screw location front of glide top front (finished edge) HC 21812 26027 41404 back x12 x12 x4 spacer 1/4" screw bottom drawer glide 2. 3. 4. 5. Fully extend drawer glides to the front. Place 1/4" screws through the correct holes for the back and middle screws of the drawer slide, then through the spacers and into the holes on the panel. Tighten screws but do not over tighten. Close slide until the front hole is visible through the oval slot on the glide. Place 1/4" screws through the hole in the slot and through the spacer. 6. Tighten screw but do not over tighten. 19
step 12 case assembly - attach top rail PA LA finished front edge 31570 x4 25266 x2 finished front edge cam bolt long flat head screw 2. 3. Screw the cam bolts into the small holes (inner holes) on top panel. Cam bolts must be screwed down flush. Place long flat head screws through holes on top rail. Make sure the finished side of the rail is facing the front. Line up dowel pins with the holes in the top panel, then tighten screws. 20
step 13 base assembly - attach rail and bottom pannel PB ID FC 2. Put dowels on the rail (with corner brackets) into the holes on the left panel (in the middle of the side). Place the bottom panel to the left panel inserting dowel pins and cam bolts into the holes. 21
step 14 base assembly - attach rail and panel HC ID PB 2. Attach the remaining rails (PB) and the right panel (HC). Make sure dowel pins and cam bolts are completely inserted and then tighten the cams under the bottom. 22
step 15 case assembly - attach back panel S S FC ID Attach the back panel by sliding it into the grooves in the side and bottom panels. 23
step 16 case assembly - attach top assembly LA PB S HC FC PB ID PB 2. Attach the top panel by pressing in onto the back panel and by inserting dowel pins and cam bolts into the holes. Make sure dowel pins and cam bolts are completely inserted and then tighten the cams. 24
step 17 case assembly - attach corner bracket HC LA S 25233 x2 S ID short flat head screw FC Fasten the middle rail (with corner brackets) to the left and right panel with the short flat headed screws. 25
step 18 case assembly - attach rectangular feet 1/4" front edge IMPORTANT: When placing this unit on thick carpet, the addition of 4 rectangular feet is required to improve stability. For floors with a hard surface or low pile carpeting, the additional feet are not necessary. finished front edge LA FC S 12754 x4 25241 x8 1" S HC back edge rectangular foot flat head screw ID 2. 3. Place a rectangular foot on the bottom of the side panel at a distance from the front edge of 1/4" and 1" from the back edge, centered on the width of the panel-side. Place the screws through to two holes and gently screw them onto the side panel. Make sure to fasten the screws, but be careful not to over tighten. Repeat step 1-2 for the remaining 2 feet. 26
step 19 case assembly - attach back panel clips 2" 90 4" HC 4" PA S 2 x 4" 4" 10401 x12 S panel clips FC PB Place back panel clips as shown from inside, and press the thin tabs between the back panel and the groove. 2. Tighten the screws but be careful not to over tighten. 27
step 20 case assembly - mount wall attachment strips 1 2 3 1 1/5" IMPORTANT. The screw supplied together with the wall attachment strip is to be used only for fixing the wall attachment strip to the furniture. In addition to this, you vill need to choose a screw or fitting which is suitable for securing the bracket to the kind of walls you have. If you are unsure about what type of screw to usee contact your local handware store. Wall attachment strip are required to be installed. 94073 LA x2 FC S wall attachment strip HC 2. 3. Place the dresser in the desired position against the wall. Mark the locations of the TWO wall attachment SLOTS at the top of the DRESSER. MEASURE down 1 1/5" from the mark at the top of the case and attach the two wall STRIPS with washers and screws. Note - The washers and screws for wall attachment should be purchased from a hardware store to suit the type of wall. Pass the wall attachment strips through the slots at the top back of the case, and attach them to the underside of the DRESSER top with the screws and washers that are included in the PACK. ID 28
step 21 case assembly - install drawers into case LA EA EA 26214 x8 EA HC machine screw EA 2. 3. Slide groove on drawer sides over the drawer glide. Pull the slide forward until the threaded hole on the glide aligns with the hole in the drawer side. Attach glide screw from inside the drawer box into the drawer glide. 29
specification sheet 3 YEAR WARRANTY: All Tvilum furniture is warranted to the original purchaser at the time of purchase and for 3 years after the purchase date. We warrant to you, the original purchaser, that our furniture and all furniture parts and components are free of defects in material or workmanship. The word defects as used in this warranty is defined as any imperfections which impair the use of the furniture. Our warranty is expressly limited to the replacement or repair of furniture parts and components and Tvilum will have a reasonable amount of time to remedy said defect. This warranty applies under conditions of normal use. The warranty does not cover defects caused by improper assembly or disassembly defects occurring after purchase due to intentional damage, product modifications, exposure to the elements, accidents, misuse, abuse or negligence and labor or assembly costs. 30 kg 60 lbs 9 kg 20 lbs All implied warranties, including the warranty of merchantability shall not extend beyond the duration of the written warranty stated above. Tvilum liability is expressly limited to the costs of material for repair or replacement of defective goods and in no event will Tvilum be liable for incidental or consequential damages resulting from use of the product. Some states do not allow limitations on how long an implied warranty may last or the exclusions or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights which may vary from state to state. Any claims made under this warranty must be presented in writing to: Tvilum 2195 Philpott Road South Boston, VA 24592 30
Read more at www.tvilum.com THIS PRODUCT will ensure you A product tested for harmful substances Helps to maintain healthy indoor climate Wood from sustainable forestry The furniture is PEFC-certified Safe furniture for use in your home The furniture has been safety tested and approved Minimum 25% post consumer recycled materials 31
products available 4 drawer dresser 6 drawer dresser 32
33