Digital Menu Board Ceiling Mount Installation M2T4249C M3T4249C www.microndisplaysolutions.com
Table of Contents Important Safety... 3 Models and Specifications... 4 Package Contents... 5 Step 1 Using a Two(2) Wide or Three (3) Wide Mount Only... 6 Step 2 Joining 2 Wide and 3 Wide Menu Board Mount to make a 4 Wide or Greater Mount... 7 Step 3 Mounting to Ceiling... 8 Step 4 Tilt Mechanism Adjustment... 8 Step 5 Attaching End Caps... 8 Step 6 Attaching VESA Panel Brackets & Mounting Panels... 9 Step 7 Installing Monitor Security Locks (Optional Item)... 10 Step 8 Installing Cable Tie Clamps (Optional Item)... 10 Warranty... 11 Digital Menu Board 4249 Ceiling Mount Installation Manual Page 2
Important Safety CAUTION: Before you begin any of the installation procedures read and follow the warnings and important safety instructions within the manual. WARNING! FAILURE TO FOLLOW INSTRUCTIONS ON ACCESSING BEHIND PANELS AND SERVICING PANELS MAY RESULT IN POSSIBLE PERSONAL INJURY AND DAMAGE TO VIDEO PANELS DUE FROM FALLING! BEFORE INSTALLING THE MOUNT, ENSURE THE WALL IS STRUCTUALLY SOUND AND ABLE TO PROPERLY SUPPORT THE COMBINED WEIGHT OF MOUNT AND VIDEO PANELS! Cat No. M2T4249C and M3T4249C Tested and Evaluated to CSA Model Code SPE-1000, Clause 6.2.8. Testé et évalué selon le code de modèle CSA SPE-1000, article 6.2.8 Warning: Maximum hanging load 100 Kg for M2T4249C and 120 Kg for M3T4249C. Attention: Charge maximale suspendue 100 Kg pour M2T4249C et 120 Kg pour M3T4249C. Use the following safety guidelines to help protect you during the installation, especially with installing the video panels to mount and when access to panels is required to ensure your own personal safety. Read all the installation instructions before installing the mounting solution. Read and follow all important safety instructions. Depending on size of video mount solutions, two (2) persons may be required for installation. Please ensure all safety precautions are followed when working with heights. Digital Menu Board 4249 Ceiling Mount Installation Manual Page 3
Models and Specifications Product M2T4249C M3T42469C Type 2 Wide Tilt Menu Board 3 Wide Tilt Menu Board Screen Sizes 42 to 49 Tilt 0 to 15 Degrees Vesa 200 to 400 Security Locks Included Weight Load 100 kg 120 kg Dimensions (WxHxD) With 0 0 Tilt 1800 x 240 x 100mm 2750 x 240 x 100 Dimensions (WxHxD) With 15 0 Tilt 1800 x 240 x 150mm 2750 x 240 x 150mm Note: When joining Digital Menu Board mounts together to make overall 4 wide or larger mount please add 400mm at each joining point to arrive at overall length. Digital Menu Board 4249 Ceiling Mount Installation Manual Page 4
Package Contents Description Model Qty Picture Preassembled Mount 2T4249 1 3T4249 2 Part A Joiner Rail Assembly - Small 2T4249 3T4249 2 Part JRS Joiner Rail Assembly - Large 2T4249 3T4249 1 Part JRL Panel VESA Bracket 2T4249 4 3T4249 6 Part B End Cap - Small 2T4249 3T4249 4 Part ECS End Cap - Large 2T4249 3T4249 2 Part ECL Hardware Cable Tie Clamp Monitor Security Lock 2T4249 2 3T4249 3 2T4249 3 3T4249 4 2T4249 2 Part H Part CC N/R = Not Required 3T4249 3 Part SL Digital Menu Board 4249 Ceiling Mount Installation Manual Page 5
Step 1 Using a 2 Wide or 3 Wide Mount Only For a two (2) wide mount proceed to Step 3. For a three (3) wide mount the left and right sections need to be joined together using the four (4) joiner bars supplied. See figure 1B. Once they are joined together, tighten screws using 4mm hex wrench. See figure 1C, and 1D. Fig. 1A Fig. 1B Fig. 1C Fig. 1D Digital Menu Board 4249 Ceiling Mount Installation Manual Page 6
Step 2 Joining 2W & 3W Mounts to make a 4W or greater Mount Type For configurations requiring 4 wide or 6 wide menu boards. a) Join a 2W+2W menu board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2a, 2B, 2C. b) Tighten screws using 4mm hex wrench once they are in place. See fig. 2D and 2E. a) If required, reposition pipe flanges to desired position. Fig. 2A Fig. 2C Fig. 2B For configurations requiring 5 wide menu boards. c) Join a 2W+3W menu board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2a, 2B, and 2F. d) Tighten screws using 4mm hex wrench once they are in place. See fig. 2D, and 2E. e) If required, reposition pipe flanges. For configurations requiring 6 wide menu boards. f) Join a 3W+3W menu board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2a, 2B, and 2G. g) Tighten screws using 4mm hex wrench once they are in place. See fig. 2D, and 2E. h) If required, reposition pipe flanges. Fig. 2D Fig. 2F Fig. 2G Fig. 2E Digital Menu Board 4249 Ceiling Mount Installation Manual Page 7
Step 3 Mounting to Ceiling a) Attach menu board mount to ceiling structure using threaded pipe. Step 4 Tilt Mechanism Adjustment For a 2 wide mount there is a tilt adjustment mechanism at each end. For a 3 wide mount there are four (4) tilt adjustment mechanisms. The maximum tilt angle is 15 Degrees. a) To set desired tilt angle, loosen the tilt adjustment screws using a 4mm Allen wrench. b) Once you have the desired tilt angle desired tighten the tilt adjustment screws. Tilt adjustment screw Tilt safety screw. DO NOT ADJUST Fig. 4A Step 5 Attaching End Caps a) Install the small Black End Caps (if not already installed) on both ends of mount. See figure 5A, and 5B. b) Use clear silicone (optional) to affix End Caps. c) Install large End Caps (if not already installed) on both ends as shown in fig. 5A, and 5C by tapping into place. Small End Cap Large End Cap Fig. 5A Fig. 5B Fig. 5C Digital Menu Board 4249 Ceiling Mount Installation Manual Page 8
Step 6 Attaching VESA Panel Brackets & Mounting Panels a) Remove video display panels to be installed from their cartons and attach the Panel VESA Brackets (Part B) to back of video panels at the VESA mounts as shown in figure 6A. Mounting hardware is provided (Part F). b) The mounting hardware consists of various lengths of M6 and M8 screws to accommodate different manufacturer specifications. c) If M6 size screws are required, you will need to use the white M8 reducer sleeves provided. See figure 6B and 6C. Fig. 6A IMPORTANT The video connections and placement of AC plug will vary by model and brand. In the event any of the cabling is in line with the Panel VESA Bracket and interferes, the use of shims/plastic spacers will be required to extend VESA Panel Bracket outwards. d) Lift each video display panel and position so the upper and lower clamps on each VESA Panel Bracket slide into the t-slot of the frame assembly. See figure 6D. e) Gently slide panel into desires position along frame assembly. f) Repeat for each video display panel. Fig. 6B Fig. 6C Fig. 6D If you still need assistance with the installation, we are a phone call away at (905)-828-1662. Digital Menu Board 4249 Ceiling Mount Installation Manual Page 9
Step 7 Installing Monitor Security Locks (Optional Item) The Monitor Security Locks (Part SL) are used to secure monitor to Top Rail. a) Place one (1) Monitor Security Lock on either the left or right Top Panel Clamp for each monitor. See Figure 7A. b) Once the Monitor Security Lock has been positioned directly on top of panel clamp, secure the lock by tightening the two (2) screws. See Figure 7B. Fig. 7A Fig. 7B Step 8 Installing Cable Tie Clamps (Optional Item) The Cable Tie Clamps are used for cable management and/or to fasten media player to frame assembly, etc. a) Insert Cable Tie Clamps where desired into t-slot and then rotate the Cable Tie Clamp 90 0 to secure in place. b) Thread cable tie thru the Cable Tie Clamp as required. Fig. 8A Fig. 8B Digital Menu Board 4249 Ceiling Mount Installation Manual Page 10
Warranty Micron Display Solutions ( MICRON ) warrants to the first purchaser for this product ( Product ), when shipped in its original container and sold or distributed in Canada by Micron or by an authorized Micron dealer, and Product was not sold as is or sales final that the Product will be free from defects in material and workmanship for a period of three (3) years and will within the warranty period, either repair the defective Product or provide the purchaser a replacement of the defective Product. This warranty does not apply to any appearance items of the product nor to the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, which has been altered or modified in design or construction, or if the serial number or model number affixed to Product has been removed, defaced, changed, altered or tampered with. Micron Display Solutions 2679 Bristol Circle, Unit 6 Oakville, Ontario L6H 6Z8 (905)-828-1662 www.microndisplaysolutions.com Digital Menu Board 4249 Ceiling Mount Installation Manual Page 11