HZ0A0TX/ HZ0B0TX Shadowbox Wine/Bar Cabinet Assembly Instructions For assistance with assembly contact: Southern Enterprises Inc. Customer Service -800--509 service@seidal.com www.seidal.com Due to weight, assembly requires two people. Following detailed instructions, assembly should take approximately two hours.
PACKAGE CONTENTS A S T S O M O W J P L N D V J J S T T S K C F U Y Q J U G G U X H E Q I B R Z Z R
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY A Top Panel N Shelf B Bottom Panel O Vertical Panel C Left Side Panel P Vertical Panel D Right Side Panel Q Wine Rack Panel 4 E Shelf R Leg F Shelf S Glass Rack Side 4 G Vertical Panel T Glass Rack Middle 4 H Vertical Panel U Wine Shelf I Shelf V Back Panel J Vertical Panel 4 W Back Panel K Shelf X Left Door L Shelf Y Right Door M Shelf Z Metal Rail 4 HARDWARE CONTENTS 4 Wood dowel Qty: 9 Cam bolt Qty: 8 Cam lock Qty: 8 Hinge Qty: 5 7 8 Screw / L Qty: 4 Screw / L Qty: 48 Magnet Qty: Screw -/4 L Qty: 4 9 0 Screw -/8 L Qty: 4 Bracket Qty: 4 Plastic strap Qty: Anchor Qty: 4
4 5 Screw 5/8 L Qty: 4 Bolt / L Qty: 4 Allen wrench Qty: Paper cover Qty: 8 4
Wood may scratch easily, please Be careful when assembling. Do not scratch.. Attach shelf (M), vertical panels (O) and shelf (N) by inserting wood dowels () into holes. M O O N Wood Dowel x 8. Insert cam locks () into holes in assembled unit on Figure. Screw cam bolts () into holes on vertical panel (P). Attach vertical panel (P) to assembled unit on Figure by inserting wood dowels () and cam bolts () into corresponding holes until vertical panel (P) and assembled unit on Figure meet. Tighten by rotating cam locks () in clockwise direction with Phillips screwdriver. Cover cam lock holes with paper covers (). N P Wood Dowel x 4 Cam Bolt x 4 Cam Lock x 4 Paper Cover x 4 5
. Insert cam locks () into corresponding holes in assembled unit on Figure. Screw cam bolts () into corresponding holes on shelf (L). Attach shelf (L) to assembled unit on Figure by inserting wood dowels () and cam bolts () into corresponding holes until shelf panel (L) and assembled unit meet. N Tighten by rotating cam locks () in clockwise direction with Phillips screwdriver. Cover cam lock holes with paper covers (). J Make sure cam lock holes on shelf (L) are facing down as shown on illustration. L Wood Dowel x 4 Cam Bolt x 4 Cam Lock x 4 Paper Cover x 4 4 4. Attach magnets (7) to shelf (K) using screws (). Tighten screws with Phillips screwdriver. 7 7 Screw / x 4 Magnet x K
5. Insert cam locks () into corresponding holes on vertical panels (J). Screw cam bolts () into corresponding holes on assembled unit on Figure. Attach assembled unit to vertical panels (J) by inserting wood dowels () and cam bolts () into corresponding holes until vertical panel (J) and assembled unit meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). 5 Repeat these steps to attach shelf (K) to assembled parts. Wood Dowel x 8 J J K Cam Bolt x 8 Cam Lock x 8 Paper Cover x 8. Insert cam locks () into holes on vertical panels (G). Screw cam bolts () into holes on shelf (F). Attach shelf (F) to vertical panels (G) by inserting wood dowels () and cam bolts () into corresponding holes until they meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). Repeat steps to attach shelf (E) to vertical panels (G). F G G Wood Dowel x 8 Cam Bolt x 8 Cam Lock x 8 E Paper Cover x 8 7
7. Insert cam locks () into holes in assembled parts from Figure. Screw cam bolts () into holes on vertical panel (H). Attach vertical panel (H) to assembled unit on Figure by inserting wood dowels () and cam bolts () into corresponding holes until vertical panel (H) and assembled unit meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). Wood Dowel x 4 7 H Cam Bolt x 4 Cam Lock x 4 Paper Cover x 4 8. Insert cam locks () into holes on shelf (I). Screw cam bolts () into holes on assembled unit on Figure 7. Attach shelf (I) to assembled unit on Figure 7 by inserting wood dowels () and cam bolts () into corresponding holes until they meet. 8 Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). Wood Dowel x Cam Bolt x I Cam Lock x Paper Cover x 8
9. Insert cam locks () into holes on vertical panel (J). Screw cam bolts () into holes on assembled unit on Figure 8. Attach vertical panel (J) to assembled unit on Figure 8 by inserting wood dowels () and cam bolts () into corresponding holes until vertical panel (J) and assembled unit meet. 9 Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). J Wood Dowel x Cam Bolt x Cam Lock x Paper Cover x 0 0. Attach magnets (7) to bottom panel (B) with screws (). Tighten screws with Phillips screwdriver. 7 7 Screw / x 4 Magnet x B 9
. Insert cam locks () into holes on assembled unit on Figure 9. Screw cam bolts () into holes on bottom panel (B). Attach bottom panel (B) to assembled unit on Figure 9 by inserting wood dowels () and cam bolts () into corresponding holes until bottom (B) and assembled unit meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). Wood Dowel x B Cam Bolt x Cam Lock x Paper Cover x. Insert cam locks () into holes in assembled unit on Figure. Screw cam bolts () into holes on assembled unit on Figure 5. Attach assembled parts from Figure 5 to assembled unit on Figure by inserting wood dowels () and cam bolts () into corresponding holes until units meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). Wood Dowel x 4 K B Cam Bolt x 4 Cam Lock x 4 Paper Cover x 4 0
. Attach hinges (4) to left side of panel (C) with screws (5). Note: Do not tighten the screws until step 4 is complete. 5 4 4 Hinge x C 5 Screw / L x 4. Attach hinges (4) to right side of panel (D) with screws (5). 4 Note: Do not tighten the screws until step 4 is complete. 5 4 D 4 Hinge x 5 Screw / L x
5. Insert cam locks () into holes on assembled parts from Figure. Screw cam bolts () into holes on left side panel (C). Attach left side panel (C) to assembled unit on Figure by inserting wood dowels () and cam bolts () into corresponding holes. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Repeat steps to attach right side panel (D). Cover cam lock holes with paper covers (). This step may take two people to complete. Work panels (C) and (D) from bottom to top assuring that all cam bolts and wood dowels are inserted through their corresponding holes. 5 C D B Wood Dowel x Cam Bolt Cam Lock Paper Cover x x x. Attach magnets (7) to top panel (A) with screws (). Tighten screws with Phillips screwdriver. 7 Screw / x 4 A 7 Magnet x
7. Insert cam locks () into holes assembled unit on Figure 5. Screw cam bolts () into holes on top panel (A). Attach top panel (A) to assembled unit on Figure 5 by inserting wood dowels () and cam bolts () into corresponding holes until assembled unit meet. Tighten by rotating cam locks () clockwise with Phillips screwdriver. Cover cam lock holes with paper covers (). 7 A Wood Dowel x 8 Cam Bolt x 8 Cam Lock x 8 Paper Cover x 8 8 8. Slide wine rack panels (Q) together as shown. Note: Please make sure all finished and unfinished sides are facing the same way. Q Q Q Q
9 9. As shown in Figure 9, insert assembled wine panels on Figure 8 and wine shelf (U) in assembled unit on Figure 7. This step is completed through the back of the unit. U 0. Attach glass rack side (S) and glass rack middle (T) to assembled unit on Figure 9 using screws (8) and wood dowels (). Tighten screws with Phillips screwdriver. Wood Dowel x 0 8 S T 8 8 Screw -/4 L x 4
. Attach back panels (V) and (W) with screws (). Tighten screws with Phillips screwdriver. W Screw / x V. Attach metal rails (Z) to legs (R) with bolts (4) as shown in Figure. Tighten bolts with Allen wrench (5). Don t fully tighten bolts until Figure is complete. R Z 4 Blot x 8 Z R 5 Allen wrench 4 5 5
. Attach assembled unit on Figure to assembled unit on Figure using bolts (4). Tighten bolts with Allen wrench (5). 4 5 Blot x Allen wrench 4 5 4. Attach left door (X) and right door (Y) using screws (5). 4 Tighten all screws with Phillips screwdriver. Y 5 Screw / L x 8 X 5
5. Attach brackets (0) to back panels using screws (). Tighten screws using Phillips screwdriver. Mark two desired locations on wall. Drill two /" holes on wall. Insert plastic anchors () into holes in wall as shown. Tip: You may want to hammer plastic anchors into wall. Attach brackets (0) to wall using screws (9). Tighten screws () using Phillips screwdriver. 5 0 9 0 9 0 Screw -/8 L x 4 Bracket x 4 Anchor x 4 Screw 5/8 L x 4. Move item close to the wall brackets (0) and tie in both brackets (0) with plastic chains strap () as shown in Figure. Plastic strap x 7
7 7. Your Shadowbox Wine/Bar Cabinet is ready for use. 8
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Quantity Needed Please examine this product carefully upon immediate receipt. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise. Please contact Southern Enterprises at 800--509 or in Dallas 97-89-0/ 9am 4pm Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for customer service representative for issues involving damages or replacement parts. Please ask for technical assistance representative for any issues with product and assembly/construction. Please contact the retailer that you purchased from for returns. Customer Service -800--509 service@seidal.com Southern Enterprises, Inc. 00 Freeport Parkway, Suite 00 Coppell, Texas 7509