15mm Solid European Droploc Oak Fitting Guide & Warranty Information
|
|
- Prosper Rose
- 5 years ago
- Views:
Transcription
1 15mm Solid European Droploc Oak & Warranty Information
2 Introduction Congratulations on your purchase of your brand new Timba Floor 15mm European Solid Oak Flooring. Prior to installation please examine all boards for faults that are not solid wood compatible (such as physical damages etc.) and use only boards that are in proper condition. The term fault however, does not refer to any natural features or the natural characteristics of solid wood. During installation it is important to make sure that floorboards from different packages (at least 3-4) and different lengths are being mixed in order to achieve a well-balanced and harmonious appearance. Installation for floating floor installation with Click Profile Fig.1 If you don t have to narrow the width of your first row of planks, begin by sawing off the longitudinal tongues of the entire first row of planks. Start laying the first row in the left hand corner of the room with the sawn edge facing the wall. Use spacer wedges to ensure the necessary distance / expansion gaps to the wall; 3mm per meter of installation width (minimum 15mm); for the longitudinal direction 15mm is required and appropriate for all lengths. If the wall is not straight see Fig.13. Lay out the first row in a straight line and let the short ends interlock, see Fig.7. Fig.2 & 3 Begin the second row on the left by clicking the longitudinal tongue of the first board into the groove of the first row. To do so, insert the tongue into the groove at a angle of 25 and lower the board. As it is lowered the board snaps into place tightly giving you a press fit. Fig.4 The next board - and all others that follow - is inserted lengthwise as described above, the header joint must be flush with that of the previous board and inserted before lowering (for Drop Loc function to activate). Therefore the floorboards must join flush together before proceeding with the next board.
3 Fig.5,6,7 The longitudinal joint is then locked from the left to right along the entire board by simple pressing the two boards together and pushing downwards. (Fig.3) Before locking the short end joint, always make sure that the longitudinal joint is locked completely along the entire length of the board. The short end joint is locked by dropping the two boards together (Please ensure that the two short ends are lying closely together as locking is not possible otherwise, see Fig.4) Continue to install all other boards in this manner. Fig.8,9 If on either completing a row or during the installation process you experience any problems it is best advised to stop and take out this section of flooring and start the process again from where the difficulty first occurred. To disassemble, lift of the entire row of boards and pull them out of the previous row diagonally. Then you can slide the short end joints apart. To do so, it is best to use a piece of residue board between the rows of boards and knock the boards apart with hammer and hammering block. After just a few hits with hammering block, the connection can be pulled further apart by hand. In this way, the locking mechanism remains intact and the boards can be reused. Fig.10 Measure the end price with a try square (lay down the board with the groove side facing the previous row) and cut to length. Don t forget the expansion space to the wall. If you are using a jigsaw, have the top surfaces of the board face downwards, if you are using a table saw, let it face upwards.
4 Fig.11 Use a piece of residue board to help fit the last row. Remember to keep an expansion space of 3mm for every meter of installation width to the wall. Fig.12 The floor is ready for use as soon as the installation is complete. Remove the spacer wedges and attach the skirting boards. Fig.13 If the wall is not straight, align the first row in a straight line and follow the course of the wall. Saw the boards off accordingly and backfill the space between the row of boards and the wall.
5 Fig.15 A,B,C How to fit your flow around heating pipes: As with all other constructional elements, heating pipes require an expansion space of 3mm per meter of installation width. (lengthwise 15mm regardless of length). Use two residual pieces of flooring and mark the drilling spot as shown in the illustration. The cover must not be fixed on the wood flooring and should be 5mm larger fall around than the cut-out area in the floor. If desired, you can sooth or bevel the edges and treat the cutting edge with Treatment Oil. Fig.16 Laying in inaccessible places: If the boards cannot be inserted diagonally and clicked together, it is recommended that you remove the catch mechanism on the lower side of the tounge and glue the boards together. Apply the glue to the lower surface of the groove and slide the boards into one another lying flat (conventional tongue and groove principle) on the floor. For transitions and finished (e.g in front of doors etc.), we recommend using a Solid Wood Profile available from your Timba Floor Stockist.
6 Warranty UK 1. Timba is responsible for manufacturing defects. 2. The warranty lasts for 10 years starting from the date of purchase. The original invoice is proof of date of purchase. 3. Timba flooring must be installed correctly according to the above mentioned instructions. The warranty covers normal use. The warranty does not cover the use in damp and wet spaces, such as conservatories, bathrooms and kitchens. 4. Floor boards showing visible defects should not be installed. It is the responsibility of the owner/fitter to deselect these boards at time of installation. These boards are to be allowed for in the 5% waste tolerance. Boards with visible defects that are installed as such are excluded from this warranty. Colour and grade deselection is not allowed for as this is personal choice and not a defect in manufacture. 5. Finished flooring, i.e. lacquered, stained, oiled, brushed, or other finished flooring is subject to normal wear and is not covered by this warranty, i.e. if you don t maintain the floor correctly, the warranty is null and void. 6. Excluded under this warranty are: scratches, heavy impacts, humidity, and damage caused by incorrect use or lack of correct maintenance. 7. If you have a defect which falls under the conditions mentioned in this warranty, you should report this to your dealer in writing within 14 days after detecting the defect. In your letter you should include a copy of the invoice. 8. The warranty provided only relates to the floor boards supplied, consequently it does not include labour costs, the costs of additional material and any other consequential loss. 9. In case of a dispute arising from the Timba warranty, either party may call upon an independent expert to render binding advice. In the event that this clause is applicable, the cost of same shall be agreed on in writing by all parties involved in advance. 10. The 10 year warranty period will continue from original date of purchase and will not be affected by subsequent resolution of any complaint. 11. Where the Timba warranty applies, Timba or its distributors will replace the faulty floor boards. In case the product in question is no longer available, Timba will ensure replacement by an alternative product of the same quality. 12. This warranty shall apply only to the original owner/ purchaser of this wood floor. Warranty will not be applicable in case of: 1. The floor not having been fitted in accordance with the instructions by a properly qualified installer. 2. The faults were noticeable prior to the floor being fitted. 3. Defects and/or faults having arisen due to dampness and/or water damage or any other causes as a result of force majeure. 4. Defects and/or faults having been caused by improper use or negligence and failure to use the product for its intended purpose, as well as having been caused by having disregarded the instructions with respect to installation, use and maintenance. 5. Visual faults having arisen as a result of any deformation of the floor boards due to changed climate conditions, any variations in colour due to the influence of sunlight and the effects of regular aging and/or wear and tear of the finishing coat. Manufacturing Tolerance WOODEN HARDWOOD FLOORS ARE A NATURAL PRODUCT AND AS SUCH ARE SUBJECT TO MANY VARIANCES IN COLOUR AND CHARACTER IN EACH INDIVIDUAL PIECE OF FLOORING, WE ALWAYS THEREFORE RECOMMEND YOU WORK FROM 3-4 PACKS OF FLOORING AT A TIME IN ORDER TO GET THE BEST NATURAL COLOUR MIX. AS SUCH A TOLERANCE OF 5% SHOULD BE ALLOWED FOR THE DESELECTION OF ANY MATERIAL DEEMED UNSUITABLE FOR INSTALLATION. THIS PRODUCT IS PRODUCED WITH A MANUFACTURING TOLERANCE OF + OR 1.5% ON THE DIMENSION OF THE BOARD AND IN LINE WITH SPECIFIED TIMBER MANUFACTURING GUIDELINES, AS SUCH ANY ITEMS OUT OF TOLERANCE SHOULD BE DISMISSED AS PART OF THE 5% MANUFACTURING TOLERANCE.
Installation Instructions
Information You will find all illustrations and instructions on the backside of the box and on the inserted instruction folder in the package. General The floor should be a floating installation i.e. not
More informationFor best results, it is essential that you follow the installation instructions exactly.
For best results, it is essential that you follow the installation instructions exactly. PREPRTION Let the planks acclimatize for 48 hours in the unopened packaging at the normal room temperature, in the
More informationAquaGuard - Water Resistant Flooring Installation guidelines
AquaGuard - Water Resistant Flooring Installation guidelines Before You Start: Please read all the instructions before you begin the installation. Improper installation will void the warranty. Important
More informationINSTALLATION INSTRUCTIONS FOR ELKALAMINATE. IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY.
INSTALLATION INSTRUCTIONS FOR ELKALAMINATE. IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY. PREPARATION Let the planks acclimatize for 48 hours in the unopened packaging
More informationINSTALLATION INSTRUCTIONS of Chevron and Herringbone Engineered Hardwood Flooring
INSTALLATION INSTRUCTIONS of Chevron and Herringbone Engineered Hardwood Flooring www.tomson-floors.com TABLE OF CONTENTS 3 USING THE PRODUCT 3 YOUR RESPONSIBILITIES 4 PRE-INSTALLATION INSPECTION 5 BASIC
More informationINSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE WITH HYDROSEAL TECHNOLOGY.
. PREPARATION. INSTALLATION. FINISHING. MAINTENANCE INSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE WITH HYDROSEAL TECHNOLOGY. IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE.
. PREPARATION. INSTALLATION. FINISHING. MAINTENANCE INSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE. IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY. - 0-% RH 8h
More informationTORLYS LEATHER PLANK INSTALLATION INSTRUCTIONS
ENGLISH INSTRUCTIONS TORLYS LEATHER PLANK INSTALLATION INSTRUCTIONS Dear Customer, You have chosen a high quality TORLYS Leather floor, well suited for all residential application except bathrooms and
More informationFITTING INSTRUCTIONS FOR OFD SOLID OAK FLOORING
FITTING INSTRUCTIONS FOR OFD SOLID OAK FLOORING SECTION 1 Installers Responsibility Pre-Installation SECTION 2 Glue Down (Solid & Engineered Flooring) SECTION 3 Secret Nailing (Solid & Engineered Flooring)
More informationInstallation Instructions for Engineered Wood Flooring
Installation Instructions for Engineered Wood Flooring PLEASE READ THESE INSTRUCTIONS IN THEIR ENTIERTY BEFORE BEGINNING THE INSTALLATION. Installer s / Owners Responsibility As a natural product, hardwood
More informationInstallation Instructions for Viking Hearth Engineered Wood Flooring
Installation Instructions for Viking Hearth Engineered Wood Flooring 4.16.15 PLEASE READ THESE INSTRUCTIONS IN THEIR ENTIERTY BEFORE BEGINNING THE INSTALLATION. Installer s / Owners Responsibility As a
More informationLAMINATE FLOORING INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. If your starting wall is uneven, refer to Fig 11 to prevent having to uninstall rows. Taking measurements to ensure you will not have too small a final
More information1INSTALLATION GUIDE: ENGINEERED WOOD FLOORING
1INSTALLATION GUIDE: ENGINEERED WOOD FLOORING INSTALLATION GUIDELINES FOR ENGINEERED WOOD FLOORING These guidelines are designed to complement the current South African Flooring Standards. Engineered wood
More informationFor ANGLE-DROP Styles
For ANGLE-DROP Styles BEFORE INSTALLATION: 1. READ THESE DETAILED INSTALLATION INSTRUCTIONS. 2. Material and tool requirements: - Estimate square footage and add 10%. - Select underlayment (over concrete
More informationColumbia Laminate Installation Instructions
Columbia Laminate Installation Instructions 1. General Uniclic is a revolutionary system for installing laminated flooring without using glue. Uniclic uses an ingenious form of tongue and groove to click
More informationInstallation instructions for Egger Laminate and Comfort flooring with UNI fit! installation system
Installation instructions for Egger Laminate and Comfort flooring with UNI fit! installation system Obligatory testing and exercise of due care / Sub-floors 1. Obligatory testing and exercise of due care
More informationINSTALLING YOUR UNICLIC FLOOR - Small planks / 3 sizes
INSTALLING YOUR UNICLIC FLOOR - Small planks / 3 sizes 1) General The panels must be rotated on both short and long edges to fit into one another. This can be performed by inserting either the tongue into
More informationIMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING INSTALLATION & MAINTENANCE FOR ENGINNERED HERRINGBONE
IMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING INSTALLATION & MAINTENANCE FOR ENGINNERED HERRINGBONE ACCLIMATIZATION AND STORAGE Your new flooring has to be acclimatized before installation,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1/5 Dear customer, We thank you for purchasing our Par-ky floor. Before starting the installation, it is essential to read these instructions carefully. If these instructions
More informationPlease read and review installation instructions completely before proceeding with the actual installation.
INSTALLATION INSTRUCTIONS Important / Read First Please read and review installation instructions completely before proceeding with the actual installation. Owner / Installer responsibility The installer
More informationINSTALLATION. GlUElEss CliCK BamBoo installation GUidE. Introduction. Tips for a successful installation
GlUElEss CliCK BamBoo installation GUidE Introduction Thank you for purchasing a Yanchi Bamboo Floor! Our flooring combines superior technology and the highest quality materials available so that your
More informationGeneral Installation Instructions
General Installation Instructions Good web sites to check out that may assist you are: For gluing engineered boards over timber chipboard/particle board/ yellow tongue: https://www.youtube.com/watch?v=bpyfr373tl8
More informationINSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE WITH HYDROSEAL TECHNOLOGY.
. PREPARATION. INSTALLATION. FINISHING. MAINTENANCE INSTALLATION INSTRUCTIONS FOR QUICK-STEP LAMINATE WITH HYDROSEAL TECHNOLOGY. IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS
More informationWOOD. Floating. Installation Instructions
WOOD Floating Installation Instructions Conditions Floating installation means that the wood floor is not attached (i.e. with nails or adhesive) to the subfloor. The subfloor must be level, sound, dry
More informationEngineered Hardwood Flooring Installation Instructions
Engineered Hardwood Flooring Installation Instructions 1 Important Information before You Begin 1.1 Installer/Owner Responsibility Carefully inspect all materials before installation. Materials installed
More informationENGINEERED WOOD INSTALLATION GUIDE: The Cardinal Collection
ENGINEERED WOOD INSTALLATION GUIDE: The Cardinal Collection READ BEFORE INSTALLATION OF OILED FINISHED FLOORING DO S 1. Do mix wood from several boxes of flooring during installation. 2. Do make your best
More informationPVCu FOLD & SLIDE DOOR OUTWARD OPENING
PVCu FOLD & SLIDE DOOR OUTWARD OPENING STEP-BY-STEP FULLY ILLUSTRATED ASSEMBLY INSTRUCTIONS This product is covered by a 10 year manufacturer s guarantee. Should any part of it become defective due to
More informationGeneral Installation Instructions. Laminate Drop & Lock installation - 2G
General Installation Instructions Laminate Drop & Lock installation - 2G A. INTRODUCTION Laminates and other wooden material acts after the surrounding climate, the main factor is the relative humidity
More informationUnit5EustonStreet FreemensCommon Leicester LE27ST T: F:
Unit5EustonStreet FreemensCommon Leicester LE27ST T:01162741050 F:01162741046 SECTION 1: INSTALLERS RESPONSIBILITY It is the installers responsibility to carry out the final inspection of the floor to
More informationFitted Furniture Installation and Aftercare Guide
Fitted Furniture Installation and Aftercare Guide Customer Service Contact Number 08008 778899 Important Information In the unlikely event that your product is damaged or faulty in any way, this must be
More information6X3 Patio Garden Shed Assembly Manual
Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear
More informationINSTALLATION GUIDE.
INSTALLATION GUIDE Hardwood floors are a product of nature and therefore not entirely free of typical timber features such as grain variation and knots. Every piece of wood has different grain, colour
More informationInstallation instructions
1/5 Installation instructions Dear customer, We thank you for purchasing our Par-ky floor. Before starting the installation, it is essential to read these instructions carefully. INSTALLATION MATERIALS
More informationGalaxy SPC RIGID-CORE UNICLIC HYBRID PLANK. Installation Guidelines
Galaxy SPC RIGID-CORE UNICLIC HYBRID PLANK Installation Guidelines ** Read all instructions carefully before installing. Incorrect installation will invalidate and void warranty. ** The planks you are
More informationINSTALLATION LAMTON INSTALLATION INSTRUCTIONS. Lamton Laminate Flooring with Underlay Attached Glueless Installation. Tools and Accessories
Lamton quality laminate flooring is manufactured to exacting standards for long life and lasting beauty. Following these simple procedures for installation and it will ensure many years of pride and satisfaction.
More informationManufacturer 12mm Laminate Flooring Installation Guidelines
Manufacturer 12mm Laminate Flooring Installation Guidelines IMPORTANT Do not open immediately. Before opening, acclimatize planks for 48 hours by laying each box horizontally and individually in the center
More informationLinda Barker Collection Heritage Collection Classic Collection INSTALLATION GUIDE
Linda Barker Collection Heritage Collection Classic Collection INSTALLATION GUIDE Ruler Pencil Masking tape Measuring tape Silicone sealant & silicone gun Power drill & screwdriver High-grab adhesive Jig
More informationWOODLOC STAPLE DOWN INSTALLATION INSTRUCTIONS
FEBRUARY 2017 WOODLOC STAPLE DOWN INSTALLATION INSTRUCTIONS Applicable to: Kährs Spirit 10mm 3/8 Kährs Avanti 12 & 13mm 1/2 Kährs Original 15mm 5/8 Kahrs Supreme 15mm 5/8 PROTECT YOUR INVESTMENT! Maintain
More informationLaminate Flooring Alternative to Hardwood Flooring
Laminate Flooring Alternative to Hardwood Flooring Laminate flooring is moderately expensive, with a cost generally between that of vinyl and hardwood flooring. It's easier to install than hardwood and
More informationDuChâteau Vinyl DeLuxe Grand Collection LuxCor Click Installation Instructions
DuChâteau Vinyl DeLuxe Grand Collection LuxCor Click Installation Instructions General Information Intended for indoor residential and commercial use only, DuChâteau Vinyl DeLuxe Grand Collection - Luxcor
More informationInstallation Instruction
Installation Instruction WOOD Glue Down Installation Conditions Gluing to the subfloor reduces the movement of the wood floor, and is recommended for laying patterns, covering large areas, etc. The subfloor
More informationRetractable Gate IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE.
Retractable ate Fits openings up to 71 (1.8m) IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE. This product complies with safety standard ASTM F1004-10. AFTER SALES
More informationTONGUE & GROOVE NAIL-DOWN INSTALLATION INSTRUCTIONS
FEBRUARY 2017 TONGUE & GROOVE NAIL-DOWN INSTALLATION INSTRUCTIONS Applicable to: Kahrs Supreme 20mm 3/4 Grande Collection Only PROTECT YOUR INVESTMENT! Maintain your warranty: Only use Kährs branded underlayments,
More informationNEVADA ASSEMBLY INSTRUCTIONS
NEVADA ASSEMBLY INSTRUCTIONS BASE SIZE: 2.700m x 1.500m NEVADA Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Screwdriver - Flat 3/8 Hex Drive bit 8mm Hex Drive bit Drill
More informationWood Flooring Collection. Bringing affordable style to any home
Wood Flooring Collection Bringing affordable style to any home 2 Product Options Multiply - Featuring a top surface of solid wood bonded to multiple layers of cross-laid ply to create a highly stable hardwood
More informationLandscape Collection
Landscape Collection Installation Guidelines READ BEFORE INSTALLATION OF OILED FINISHED FLOORING We are providing a brief explanation of the Do s and Do Not s during and shortly after installation. DO
More informationFABA. Installation Instructions. Conductor Bar System. Publication #FABA-03 3/1/04 Part Number: Copyright 2004 Electromotive Systems
FABA Conductor Bar System Installation Instructions Publication #FABA-03 3/1/04 Part Number: 005-1062 Copyright 2004 Electromotive Systems 1S 100 Z Installation Instructions Contents: Basic Diagram - -
More informationTall Wide Extra Deep Bookcase
Tall Wide xtra Deep Bookcase Assembly Instructions - Please keep for future reference 8/650 Dimensions Width - 78cm Depth - 9cm Height - 180cm Important Please read these instructions fully before starting
More informationEnglish Professional Installation Guidelines
Professional Installation Guidelines General Installation Instructions NOTE: After proper acclimation, open cartons just prior to installation. NOTE: Mannington Laminate Flooring is intended to be installed
More informationDirect Importers of the Finest Exotic Hardwood Decking, Lumber, & Flooring
Direct Importers of the Finest Exotic Hardwood Decking, Lumber, & Flooring These Instructions can be found online at: http://www.advantagelumber.com/how-to/buildwoodstoragebox.html Material List 72 FEET
More informationAL13 v-line general installation guide
01 TM AL13 v-line general installation guide Vol 1 Version 1 pantented product TM AL13 architectural system www.al13.com CLAD THE WORLD TM How to Install v-line 01 TM AL13 architectural system SHEATHING
More informationWood in all its glory 2017/2018
Wood in all its glory 2017/2018 EXTRA WIDE BOARDS IN TRENDY DESIGNS HIGHLY SCRATCH, WEAR AND STAIN RESISTANT The Premium Oak range uses character grade European Oak, designed to bring the features of the
More informationPuerto Rico - 2 Door Shoes Cupboard
Puerto Rico - oor Shoes Cupboard ssembly Instructions - Please keep for future reference 04/478 imensions Width - 86cm epth - 38.5cm Height - 108cm Important Please read these instructions fully before
More informationVanity Cabinets and Mirrors Installation and User Guide
Vanity Cabinets and Mirrors Installation and User Guide MODEL NUMBERS 2451, 2452, 2454, 2455, 2457, 2459, 2453, 2456, 2458, 2460, 2470, 2473 Important :- Please quote the above model number(s) when ordering
More informationPORTROD WALL MOUNTED HEIGHT ROD
PORTROD WALL MOUNTED HEIGHT ROD USER INSTRUCTIONS P/N UMPORTROD Rev 1-052112 1 PORTROD Thank you for your purchase of this Health o meter Professional product. Please read this manual carefully, and keep
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION BJOORN PARQUET ANGLE/SNAP LOCKING SYSTEM SQUARE PATTERN PRODUCT INFORMATION A European parquet strip with a core of high-end plywood approx. 3.6 mm wear layer, pre sanded to 120
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts
More informationE7105T 5 DRAWER TALLBOY
EPSOM collection E7105T 5 DRAWER TALLBOY Congratulations on your purchase of your EPSOM 5 DRAWER TALLBOY. The EPSOM Collection is made in New Zealand from 100% New Zealand made MDF an environmentally sound
More informationFlooring Installation and Care Instructions
Flooring Installation and Care Instructions Longlife parquet Lindura wood flooring Design flooring Cork flooring Linoleum flooring Nadura flooring Laminate flooring Mouldings Care and Accessories MEISTER
More informationLaminate Floor Installation Guide
Laminate Floor Installation Guide Introduction This guide will take you through the necessary steps to install your Bel-Air Laminate Flooring. Make sure to carefully read through this guide so that you
More informationDO NOT HESITATE TO CONTACT US TO BE GUIDE DURING THE INSTALLATION OF SQUAREDECKO PRODUCTS
Table of contents Product specifications Step 1 : Surface preparation Installation guide Step 2-3-4 : Method of installation Step 5 : Layout of tiles Step 6 : Installation of tiles on the side of the structure
More informationInstallation guide. ROCKFON VertiQ. ROCKFON System T, ROCKFON System HAT. Impact-resistant and high impact-resistant acoustic wall panel solutions
Installation guide ROCKFON ROCKFON System T, ROCKFON System HAT Impact-resistant and high impact-resistant acoustic panel solutions ROCKFON System T, ROCKFON System HATT Contents System selection...3 Edges
More informationIDAHO ASSEMBLY INSTRUCTIONS. BASE SIZE: 1.800m x 1.200m
IDAHO ASSEMBLY INSTRUCTIONS BASE SIZE: 1.800m x 1.200m IDAHO Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Square Drive Bit No.2 3/8 Hex Drive Bit 8mm Hex Drive Bit Drill
More informationa. Select timber that is straight and free of defects b. For the best results use timber that is quarter sawn
Once regarded as the only way of obtaining wide panels made from solid timber. These wide panels were required for carcase construction, counter and bench tops also door and wall panelling. Modern "flat
More informationASS 70 FD folding / sliding door. Installation Guide
ASS 70 FD folding / sliding door Installation Guide IMPORTANT! These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the installation.
More informationASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationEsthec. Terrace. Manual for Assembly and Installation
Esthec Terrace Manual for Assembly and Installation 0 Table of Content 1. Introduction... 2 2. Factsheet... 3 3. Part-description... 4 3.1 Esthec Terrace profile... 4 3.2 3.3 Esthec Terrace side-profile...
More informationPlantation Compressed Bamboo Flooring Installation instructions
Plantation Compressed Bamboo Flooring Installation instructions thinking of our FUTURE Pre-installation FOR BOTH DIRECT STICK & FLOATING FLOORS Prior to installation of any floor, the installer must ensure
More informationASSEMBLY INSTRUCTIONS GL75. BASE SIZE: 2.190m x 1.520m
ASSEMBLY INSTRUCTIONS GL75 BASE SIZE: 2.190m x 1.520m CONGRATULATIONS ON PURCHASING A DURATUF GUARDIAN SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationATD AMP Variable Speed Reciprocating Saw Owner s Manual
ATD-10535 7 AMP Variable Speed Reciprocating Saw Owner s Manual Manufactured in China To ATD Tools, Inc. Specifications TECHNICAL SPECIFICATIONS Voltage: 120V Frequency: 60Hz Power input: 7 Amps No load
More informationINSTALLATION GUIDE CABINETRY
INSTALLATION GUIDE CABINETRY The instructions given here serve as general guidelines on how to install full-access cabinets in a reasonably simple installation. Many cabinet designs and installations may
More informationChester - Solid Pine Desk
Chester - Solid Pine Desk ssembly Instructions- Please keep for future reference 89/600 18/812 Dimensions Width - 120cm Depth - 50cm Height -,cm Important Please read these instructions fully before starting
More informationZenterra TM Installation Guide
Zenterra TM Installation Guide Installing the foam padding Please review this installation guide before you begin installing the floor. If you have any questions, please call us at 800-428-5306 any time
More informationDESCRIPTION TECHNICAL SPECIFICATIONS WIDTHS THICKNESS LENGTHS PROFILE ENDS GRADE DETAIL
Flooring SOLID ENGLISH OAK - HAND FINISHED FOOTWORN FLOORING DESCRIPTION Solid English Oak character grade footworn floor boarding with guaranteed traceability and accompanied by a certificate of origin.
More informationSAN DIEGO - TV Unit. Assembly Instructions - Please keep for future reference 389/6620
SN GO - TV Unit ssembly nstructions - Please keep for future reference 389/6620 imensions Width - 125cm epth - 40cm eight - 50cm mportant Please read these instructions fully before starting assembly f
More informationRYAN 6 DRAWER TALLBOY PARTS LIST
RYAN 6 DRAWER TALLBOY Congratulations on your purchase of your RYAN 6 DRAWER TALLBOY. The RYAN Collection is made in New Zealand from 100% New Zealand made MDF an environmentally sound and renewable resource.
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationHR175 Sash Replacement Kit Installation Instructions
HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationmm. 48h 25-85% RH. Leginstructies Parquet_GLUED_uniclic_A4_2017.indd 1 22/02/ :21:36 75% 50% x = 8 mm x = 10 mm x = 12 mm
Quick-Step wood fl ooring materials are delivered with instructions in the form of illustrations. The text below is covering a fl oating illustration in regards of a fl oating installation, and is divided
More informationLaying instructions Installation of multilayer Herringbone / Basket-weave with tongue and groove joint.
Laying instructions Installation of multilayer Herringbone / Basket-weave with tongue and groove joint. Preparation Store the boards in their packaging and open them as you need them. Read the instructions
More informationExterra Installation Guide
Exterra Installation Guide Installing the foam padding Please review this installation guide before you begin installing the floor. If you have any questions, please call us at 800-428-5306 any time Monday
More informationCLASSIC RANGE PLUS RANGE PHOTO WALL. Pre-installation check-list
CLASSIC RANGE PLUS RANGE PHOTO WALL The following is an installation guide for fitting Multipanel CLASSIC RANGE, PLUS RANGE, PHOTO WALL Jig saw or Hand saw Measuring Tape Ruler Pencil High-grab adhesive
More informationRoyal Collection. Installation Guidelines
Royal Collection Installation Guidelines Congratulation! Thank you for purchasing TEKA pre-finished engineered hardwood flooring. You made the right choice for the right product. Manufacture only real
More informationSAN DIEGO - Corner TV Unit
SN EGO - orner TV Unit ssembly nstructions - lease keep for future reference 385/8651 imensions Width - 100cm epth - 40cm eight - 50cm mportant lease read these instructions fully before starting assembly
More informationRequired Tools. Installation of Hook Plates & Discs. Professional Installation Guidelines for Engineered Wood & Hardwood with LocPlate Products
Professional Installation Guidelines for Engineered Wood & Hardwood with LocPlate Products Required Tools Utility Knife Chalk Line Measuring Tape Conventional cutting tools for Engineered Wood and Solid
More informationASSEMBLY INSTRUCTIONS SS2010. BASE SIZE: 2.020m x 1.020m
ASSEMBLY INSTRUCTIONS SS010 BASE SIZE:.00m x 1.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationE7106C 6 DRAWER CHEST
EPSOM collection E7106C 6 DRAWER CHEST Congratulations on your purchase of your EPSOM 6 DRAWER CHEST. The EPSOM Collection is made in New Zealand from 100% New Zealand made MDF an environmentally sound
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationUltraDeck. Decking & Railing Installation Guide.
UltraDeck Decking & Railing Installation Guide www.midwestmanufacturing.com Table of Contents: General Guidelines for Deck Installation 4 Plank Board Installation 6 QuickCap Installation 8 Cladding & Endcap
More informationSPEKVA. Installation Instructions. Solid wood. August
Installation Instructions Solid wood August 2013 www.spekva.com Table of contents Page Before installation - warranty coverage... 3 Receipt and storage... 4 Location... 4 Jointing worktops... 5 Attachment...
More informationInstall your floor between 18 and 30 C.
GOLDEN RULES 8-0 C Install your floor between 8 and 0 C. Quick-Step Livyn must be acclimatized in the room of installation between 8-0 C for a period of at least 8 hours before installation. This floor
More information12ft X 12ft Attached Breeze Pergola Assembly Manual. Outdoor Living Today. (For Both 9 and 12 High Posts) June 1st/2012 Version #4
12ft X 12ft Attached Breeze Pergola Assembly Manual (For Both 9 and 12 High Posts) Outdoor Living Today June 1st/2012 Version #4 Note: Installation of Wall Side Girders (P) and Wall Mount Brackets (M)
More informationInstallation Instructions
Supafold Slide Aside System Three Fold Room Divider Installation Instructions Distinctive Doors Ltd Supafold Slide Aside Internal Folding System IMPORTANT: Before proceeding with the installation, and
More informationPLEASE READ THIS FIRST
UNICLIC INSTRUCTION Groove Tongue PLEASE READ THIS FIRST It is wise to spend some time on planning before you start installing your new flooring. Read all of these instructions and if anything is unclear,
More informationLaying and maintenance of cement tiles
Laying and maintenance of cement tiles David&Goliath cement tiles are manufactured under licence in the Far East, according to our standards and specifications concerning colour and dimensional stability;
More informationInstallation Manual 0318
Installation Manual 0318 DOUBLE 7 CEDAR SHINGLE INSTALLATION GUIDE General Information CAUTION: REMEMBER THAT POLYMER UNDERGOES EXPANSION / CONTRACTION DUE TO VARIATIONS IN TEMPERATURE. THE FOLLOWING INSTRUCTIONS
More informationAssembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
More informationINCEPTIV INSTALLATION GUIDELINES
3D WOOD WALL PANELS INCEPTIV INSTALLATION GUIDELINES We recommend you hire an experienced finish carpenter or floor installer to achieve quality results with all Duchateau Wall Coverings. The right tools
More information