Non-Reinforced Joining Guide (1-Way Vertical or Horizontal) for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products
|
|
- Charity Gibbs
- 5 years ago
- Views:
Transcription
1 (1-Way Vertical or Horizontal) for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products Non-Reinforced Joining Guide Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits of your Andersen product are to be fully attained. Therefore, please read and follow this instruction guide completely. If your abilities do not match this procedure s requirements, contact an experienced contractor. You may direct any questions about this or other products to your local Andersen dealer, found in the Yellow Pages under Windows or call Andersen WindowCare service center at Monday through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Thank you for choosing Andersen. Every assembly and installation is different (windloads, structural support, etc.). Andersen strongly recommends consultation with an Andersen supplier or an experienced contractor, architect, or structural engineer prior to the assembly and installation of any Andersen product. For installation methods not covered in this guide, (i.e. through jamb) please visit the Architect Detail File on the web ( Andersen has no responsibility in regard to the post-manufactured assembly and installation of Andersen products. Use caution when working at elevated heights and around unit openings. Follow manufacturer s instructions for safe use of ladder and/or scaffolding. Failure to do so may result in injury or death. Follow manufacturer s instructions for safe operation of hand/power tools. Always wear safety glasses. Failure to do so may result in injury and/ or product damage. Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage. Unless specifically ordered, Andersen windows and doors are not equipped with safety glass, and if broken, could fragment causing injury. Many laws and building codes require safety glass for certain size windows and in specific locations. Andersen windows are available with safety glass that may reduce the likelihood of injury when broken. Information on safety glass is available from your local Andersen dealer. Andersen Installation Flanges DO NOT take the place of standard window and door flashing. Unit must be properly flashed and sealed with sealant, and full width drip cap for protection against water and air infiltration. Use non-reflective flashings. Highly reflective flashing tapes can raise the surface temperature of the vinyl to the point where vinyl deformation and product damage may occur. Do not apply any type of film to glass. Thermal stress conditions resulting in glass damage could occur. Use of movable insulating materials such as window coverings, shutters, and other shading devices may damage glass and/or vinyl. In addition, excessive condensation may result causing deterioration of windows and doors. Andersen and all other marks where denoted are trademarks of Andersen Corporation Andersen Corporation. All rights reserved. 1 Instruction Guide BC Revised 12/11/07
2 Parts Needed (2) Non-Reinforced, or Circle Top Gusset Plates (1) Exterior Snap-On Trim (1) Two Part (1) Interior Trim Piece (by Andersen or others) Tools & Supplies Horizontal & Vertical Joining Safety Glasses Hammer Electric Drill Clamps Caulk Gun Utility Knife Wood File Phillips Screwdriver 1/2" x 1/2" 16-Gauge Staples or #7 x 9/16" Pan Screws (Included in Single Non-Reinforced Joining Kit) 7/16" x 1" 16-Gauge Staples or #7 x 1" Flat Screws (Included in Single Non-Reinforced Joining Kit) #7 x 9/16" Pan Screws (Included in Single Non-Reinforced Joining Kit) Adhesion Promoter or Liquid Surface Deglosser 2" x 4" Skid (optional for transportation only) 2-1/4" Screws, maximum length (optional for transportation only) Non-Reinforced Gusset Plate (2 piece) Vertical Joining begins on Page 2. Horizontal Joining begins on Page 8. or Reinforced Gusset Plate (Vertical Combinations longer than 8 ft.) or Circle Top Gusset Plate (Circle Top Window Combinations) Exterior Snap-On Trim Vertical Non-Reinforced Joining for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products 1. Prepare Units for Joining - Vertical Joining Installation Flange DO NOT remove packaging clips until unit is installed. Remove unit from carton and remove banding tape. Place unit exterior side up on a clean, flat work surface. Remove Installation Flanges from sides to be joined by cutting with a utility knife. DO NOT cut ends of head and sill Installation Flange. Leave Installation Flange Extended at and Exterior view Utility Knife Side Installation Flange 2
3 2. Cut Two Part s to Length, if Required - Vertical Joining If cutting is required, use chart to cut Two Part s to length. Find unit size, then use measurement to the right of the unit. Excess Material Do not cut joining end Measurement Cut Length Chart UNIT Height JOINING STRIP LENGTH /16" /16" /16" /16" /16" /16" /16" UNIT Height JOINING STRIP LENGTH /16" /16" /16" /16" /16" /16" /16" 3. Attach s - Vertical Joining Apply 1/4" bead of sealant along sealant receiving groove of on side being fastened. Apply one on each jamb, positioning notched ends of toward center of unit as shown. Square end of must be inset 1/4" from head and sill jamb, as shown. Fasten s to frame using 7/16" x 1" 16-gauge staples or #7 x 1" Flat Screws. Space staples or screws 3" from ends and every 8". Joining Strip Jamb Dado 1/4" Bead Receiving Groove Tilt-Wash Double-Hung to Tilt-Wash Double-Hung Side Jamb Dado in Jamb Note: Detail shown without Installation Flange for clarity. 1/4" Flush Outer Face of Jamb Notched Ends of 7/16" x 1" 16-Gauge Staples or #7 x 1" Flat Screws 3
4 4. Join and Fasten Units - Vertical Joining Apply 1/4" bead of sealant along sealant receiving groove of on side being joined. Slide units together overlapping Two Part s until units are flush. Receiving Groove 1/4" Bead Non-Reinforced Joining Guide Tilt-Wash Double-Hung to Tilt-Wash Double-Hung Overlap Units Flush Note: Detail shown unattached for clarity. 5. Attach and Gusset Plates - Vertical Joining For Combinations up to 6'-0" High Clamp jambs together near head and sill. Center Non-Reinforce Gusset Plates across joined units in frame dado. Make sure units are flat to work surface before attaching Non-Reinforce Gusset Plates. Fasten Non-Reinforce Gusset Plates using twenty 1/2" x 1/2" 16-gauge staples or twelve #7 x 9/16" Pan Screws. Clamp Narrow Gusset Plate #7 x 9/16" Pan Screws or 1/2" x 1/2" 16-Gauge Staples 4
5 5. Attach and Gusset Plates - Vertical Joining (Continued) For Combinations Taller than 8 ft. Clamp jambs together near head and sill. Bend center tabs on Reinforced Gusset Plate flat as shown. Center Reinforced Gusset Plates across joined units in frame dado. Make sure units are flat to work surface before attaching Gusset Plate. Fasten Reinforced Gusset Plates using eight #7 x 9/16" pan head screws (not included). Bend Center Tabs Flat Clamp Reinforced Gusset Plate Reinforced Gusset Plate #7 x 9/16" Pan Screws 6. Cut Exterior Snap-On Trim to Length if Required - Vertical Joining If cutting is required, use chart to cut Exterior Snap-On Trim to length. Find unit size, then use measurement to the right of the unit. Exterior Snap-On Trim Cut Length Chart UNIT TRIM LENGTH UNIT TRIM LENGTH /2" /2" /2" /2" /2" /2" /2" /2" /2" /2" /2" /2" /2" /2" 5
6 7. Apply Exterior Snap-On Trim - Vertical Joining Clean and prepare inside surface of Exterior Snap-On Trim and exterior surface of side jambs where Exterior Snap-On Trim will be applied with an adhesion promoter or liquid surface deglosser. Apply as shown. Apply two, 1/4" minimum diameter, continuous beads of sealant to back side of Exterior Snap-On Trim as shown. Insert Exterior Snap-On Trim into space between side jambs and snap into position against unit frames. Clean sealant squeeze out from exterior. Apply Adhesion Promoter to Frames 1/2" 1/2" 1/2" Apply Adhesion Promoter to Inside Surfaces Adhesion Promoter Application Areas Exterior Snap-On Trim 1/4" Minimum Diameter Beads Tilt-Wash Double-Hung to Tilt-Wash Double-Hung Exterior Snap-On Trim 6
7 8. Apply Joined units are now ready for installation. Please refer to unit installation guide. If unit is being transported to a job site, proceed to Step 9. Apply Interior Trim Strip (sold separately) after unit has been installed and trimmed out. Apply sealant to completely fill void between joined units at head and sill of jambs (top and bottom of Exterior Snap-On Trim). Proceed to full width drip cap application step in the Unit Installation Guide for drip cap, flashing, and insulation steps. Installation Flange Non-Reinforced Joining Guide 9. Apply Skid to (Units Being Transported Only) - Vertical Joining If joined units are being transported to a job site, apply a 2" x 4" skid to sill using 2-1/4" (maximum) screws to secure units. Remove 2" x 4" skid before installing units. 2" x 4" Skid 7
8 Horizontal Narrow Joining for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products 1. Prepare Unit for Joining - Horizontal Joining DO NOT remove packaging clips until unit is installed. Installation Flange Remove unit from carton. Place unit exterior side up on a clean, flat work surface. Remove Installation Flanges only on sill of Transom or Circle Top Unit and head jamb of Tilt-Wash Double- Hung/Picture unit by cutting with a utility knife. DO NOT cut ends of side Installation Flanges. Installation Flange Exterior Views Transom or Circle Top Unit Utility Knife Leave Side Installation Flange Extended at Cut Installation Flange Horizontal Joining 2. Cut s to Length, if Required - Horizontal Joining If cutting is required, use chart to cut each to length. Find unit size, then use measurement to the right of the unit. Excess Material Do not cut joining end Measurement Cut Length Chart UNIT Width JOINING STRIP LENGTH /16" /16" /16" /16" /16" /16" /16" UNIT Width JOINING STRIP LENGTH /16" /16" /16" /16" /16" /16" /16" 8
9 3. Attach s - Horizontal Joining Apply 1/4" bead of sealant along sealant receiving groove of on side to be fastened to unit. Position one to sill of upper unit and one to head jamb of lower unit, with notched ends of toward center of unit as shown. Square end of must be inset 1/4" from side jamb as shown. Fasten to frame using 7/16" x 1" 16-gauge staples or #7 x 1" Flat Screws. Space staples or screws 3" from ends and every 8". Apply 1/4" bead of sealant along sealant receiving groove of on side being joined. 1/4" Beads Jamb Dado Andersen 200 Series Circle Top /Transom Window to 200 Series Tilt-Wash Double-Hung Window 1/4" Beads Jamb Dado Andersen Architectural Circle Top Window to 200 Series Tilt-Wash Double-Hung Window Notched End of #7 x 1" Flat Screws or 7/16" x 1" 16-Gauge Staples Side Jamb Dado in Jamb 3" 1/4" Flush Outer Face of Jamb Note: Detail shown without Installation Flange for clarity. 9
10 4. Join and Fasten Units - Horizontal Joining Slide units together interlocking Two Part s until units are flush. Transom or Circle Top Unit Installation Flange must overlap Tilt-Wash Double-Hung or Picture unit Installation Flange to the exterior on both sides. Exterior Sides Up (2) 1/8" Beads Construction Adhesive s Interlocked Tilt-Wash Double-Hung to Circle Top or Tilt-Wash Double-Hung to Transom Window Note: Detail shown unattached for clarity. Circle Top or Transom Unit Installation Flanges must overlap Tilt-Wash Double- Hung or Picture Unit Installation Flange to the exterior 5. Attach and Gusset Plates - Horizontal Joining Clamp units together as shown. Center Circle Top or Non-Reinforced Gusset Plates across joined units, over jamb dado. Make sure units are flat to work surface before attaching Gusset Plates. Fasten using twenty 1/2" x 1/2", 16-gauge staples or twelve #7 x 9/16" pan head screws. Clamp 1/2" x 1/2" 16-Gauge Staples or #7 x 9/16" Pan Screws Clamp Non-Reinforced Gusset Plate Circle Top Window Gusset Plate 1/2" x 1/2" 16-Gauge Staples or #7 x 9/16" Pan Screws Jamb Dado Tilt-Wash Double-Hung to Circle Top Window Jamb Dado Tilt-Wash Double-Hung to 200 Series Transom Window 10
11 6. Cut Exterior Snap-On Trim to Length if Required - Horizontal Joining If cutting is required, use chart to cut Exterior Snap-on Trim to length. Find unit size, then use measurement to the right of the unit. Non-Reinforced Joining Guide Exterior Snap-On Trim Cut Length Chart UNIT TRIM LENGTH /2" /2" /2" /2" /2" /2" /2" UNIT TRIM LENGTH /2" /2" /2" /2" /2" /2" /2" 11
12 7. Apply Exterior Snap-On Trim - Horizontal Joining For Andersen Architectural Circle Top /Transom Window joining, panning kerf along jamb being joined must be filled with sealant to properly seal Exterior Snap-On Trim. Clean and prepare inside surface of Exterior Snap-On Trim and exterior surface of jambs where Exterior Snap-On Trim will be applied with an adhesion promoter or liquid surface deglosser. Apply as shown. For Andersen Architectural Circle Top /Transom Window joining, fill panning kerf, full length, with sealant along jamb being joined. Apply as shown in detail below. Apply two, 1/4" minimum diameter, continuous beads of sealant to back side of Exterior Snap-On Trim as shown. Insert Exterior Snap-On Trim into space between joined units and snap into position against unit frames. Clean sealant squeeze out from exterior. Apply sealant to completely fill void between joined units at each end of Exterior Snap-On Trim. Joined units are now ready for installation. Please refer to unit installation guide. Apply Interior Trim Strip (sold separately) after unit has been installed and trimmed out. Proceed to full width drip cap application step in the unit installation guide for full width drip cap, flashing and insulation steps. 1/2" 1/2" 1/2" Non-Reinforced Joining Guide Apply Adhesion Promoter to Frames Adhesion Promoter Application Areas Application Area Exterior Snap-On Trim Apply Adhesion Promoter to Inside Surfaces Exterior Snap-On Trim 1/4" Minimum Diameter Beads Panning Kerf Minimum 1/4" Bead Exterior Snap-On Trim Andersen Architectural Circle Top to 200 Series Tilt-Wash Double-Hung Window Minimum 1/4" Bead Exterior Snap-On Trim Andersen 200 Series Circle Top /Transom to 200 Series Tilt-Wash Double-Hung Window 12
Non-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows
(2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly,
More informationfor Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window
for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.
More informationNon-Reinforced Joining Guide (Horizontal/Vertical)
Non-Reinforced Joining Guide (Horizontal/Vertical) for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationSteel Reinforced Joining Guide (Horizontal / Vertical)
(Horizontal / Vertical) for Andersen Patio Door and/or Elliptical Top Window Combinations Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationfor Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms
for Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationSteel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows
for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows
for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen Frenchwood Patio Door Sidelights and Transoms
for Andersen Frenchwood Patio Door Sidelights and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if
More informationInstallation Guide. for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass)
for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass) Installation Guide Congratulations! You have just purchased one of the many fine Andersen
More information1-Way Vertical Joining (Pages 2-22) 1-Way Horizontal Joining (Pages 23-44)
3/4" LVL Reinforced Joining Guide (1-Way Vertical Joining) or (1-Way Horizontal Joining) 3/4" LVL Reinforced Joining Guide (1-Way Vertical Joining) or (1-Way Horizontal Joining) for Andersen 400 Series
More informationPanel Assembly and Installation
Assembly and Installation Assembly and Installation for Andersen 400 Series Frenchwood, 200 Series Narroline, 200 Series Perma-Shield Gliding Patio Doors and 400 Series Perma-Shield Gliding Patio Doors
More informationSash Replacement Guide for Andersen Impact Resistant Casement Windows
Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006
for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More informationInstallation Guide for Andersen Architectural Clad Awning Windows
Guide for Andersen Architectural Clad Awning Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationTransom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door
Transom Joining for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door INSTALLER: Please leave this guide with the building owner to file for future reference. Congratulations! You have just
More informationInstallation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors
Installation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen 400 Series Gliding Windows
for Andersen 400 Series Gliding Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits of your
More information3/4" LVL Reinforced Joining Guide
(2-Way Horizontal and Vertical Joining) for Andersen 400 Series Tilt-Wash Double-Hung, Picture, and Transom Windows with Stormwatch Protection Congratulations! You have just purchased one of the many fine
More informationSash Replacement Guide for Andersen 400 Series Tilt-Wash Transom Windows
for Andersen 400 Series Tilt-Wash Transom Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen
More informationInstallation Guide for Andersen Architectural Clad Hinged Windows
Guide for Andersen Architectural Clad Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationReglazing Guide for Andersen 400 Series Specialty Windows with Stormwatch Protection (High-Performance Impact Resistant Glass)
Reglazing Guide for Andersen 400 Series Specialty Windows with Stormwatch Protection (High-Performance Impact Resistant Glass) INSTALLER: This reglazing procedure is to be performed only by a professional
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationInstallation Guide for E-Series/Eagle Clad Mechanically Fastened Windows
Guide for E-Series/Eagle Clad Mechanically Fastened Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationFixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows
Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows Manufactured Between September 2005 and October 2006 Read all instructions carefully before attempting
More informationStationary Panel Replacement
Stationary Panel Replacement Product Series: 200 Series Product Type: Hinged Inswing Patio Doors Read these instructions before starting procedure. For additional information visit www.andersenwindows.com.
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationInstallation Instructions for E-Series 2 or 4-Panel Gliding and French Gliding Patio Doors
Installation Instructions for E-Series 2 or 4-Panel Gliding and French Gliding Patio Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather
More informationReplacement Guide. For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System RECOMMENDED TOOLS:
Replacement Guide For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System IMPORTANT: READ ENTIRE GUIDE BEFORE BEGINNING INSTALLATION. PLEASE NOTE: Proper assembly, installation
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationAssembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame
Assembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame americancraftsmanwindows.com American Craftsman and all other marks where denoted are trademarks of Andersen Corporation
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationFollow instructions from foam, sealant and flashing manufacturer regarding material application and compatibility with this product.
Installation Guide for Andersen Wood Outswing Folding Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationInstallation Guide for E-Series/Eagle Ascent 2 or 4 Panel Gliding (Sliding) Patio Doors
Installation Guide for E-Series/Eagle Ascent 2 or 4 Panel Gliding (Sliding) Patio Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Clad Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationSash may be heavy. Use a reasonable number of people with sufficient strength to lift, carry, remove and install. Tape broken glass with duct tape bef
Improper re-glazing product (s) can affect the performance under stress and may contribute to property damage or injury in high wind conditions. The installer should not proceed with re-glazing if these
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationPassive Panel Replacement
Passive Panel Replacement Product Series: 200 Series Product Type: Hinged Inswing Patio Doors Read these instructions before starting procedure. For additional information visit www.andersenwindows.com.
More informationINSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS.
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the owner. Please read
More informationReinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows
Reinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationSash and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows
and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows Please read this guide completely before starting. For questions about this and other Andersen products, call 1-888-888-7020.
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows with Exterior Trim or Nail Fin (JII024)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows with nailing fin or primed wood windows with exterior trim. While the
More informationULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS
ULTRA WINDOW & DOOR S AND RECEIVERS INSTALLATION INSTRUCTIONS! CAUTION: *REMEMBER SAFETY FIRST* Proper Eye and! Hearing Protection must always be worn during installation of all window and door products.
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Wood Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationINSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More information26- H i n g e d P a t i o D o o r s - I n s w i n g
Contents Hinged Patio Doors - Inswing Basic Unit Details... 2 Options / Accessories Accessibility Option... 5 Andersen Grilles... 6 Extension s... 7 Anchoring Methods... 8 Joining Details... 9 Suggested
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationPassive Panel Replacement Guide
Replacement Guide for Andersen 200 Series d Patio Doors - Inswing For questions call 1-888-888-7020. For more information and/or guides visit andersenwindows.com. Please leave this guide with building
More informationWindow with Nail fin (New construction)
Window with Nail fin (New construction) Disclaimer: Improper installation and care may void warranty. These instructions are a basic/general recommendation for installation, but may not be utilized in
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
More informationInstallation Guidelines for all Quaker products with nail fins New Construction nail fin installation with a Zip sheathing system.
www.quakerwindows.com www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines for all Quaker products with nail fins New
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS
WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems
More informationVinyl Windows and Doors
Vinyl Windows and Doors Manufactured by Pella Corporation Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. Part Number: V981555 2009 Pella Corporation
More information(773) INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION & GL OSSARY ROUGH OPENINGS
Thank you for selecting C l i m a t e G u a r d products. Attached are our recommended installation instructions for Vinyl windows with an integral (2400-02) will not affect application of the ClimateGuard
More informationwindow installation Guide wood FRaMinG New Construction
window installation Guide wood FRaMinG New Construction IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing windows. Any local building code requirements supersede
More informationInstallation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
www.quakerwindows.comv www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationDOOR INSTALLATION GUIDE WOOD FRAMING New Construction
DOOR INSTALLATION GUIDE WOOD FRAMING New Construction IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing doors. Any local building code requirements supersede
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationInstallation Materials Required: Tools Required: 6" self-adhesive flashing. Shims. 3-foot level 6-foot level Tape measure 1/8" drill bit
installation instructions for CUSTOM WOOD & FIBERGLASS EXTERIOR FOLDING DOOR SYSTEMs (JII101) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032)
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More informationVISTALUXE CASEMENT, AWNING, & PICTURE WINDOW
VCSMT VISTALUXE CASEMENT, AWNING, & PICTURE WINDOW INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING ANY INSTALLATION Kolbe & Kolbe Millwork, Co., Inc. 1323 S. 11th Ave. -
More informationRetractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)
Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents
More informationIDP Entry-Fit Steel Door Frames. Installation Instructions K2A and NK2A Series Frames
IDP Entry-Fit Steel Door Frames Installation Instructions K2A and NK2A Series Frames IDP Inc 21300 W. 8 Mile Rd. Southfield, MI 48075 1-877-645-2770 www.idpframes.com email: info@idpframes.com K2A and
More informationKnock Down Patio Door Assembly Instructions Regular & Impact
Knock Down Patio Door Assembly Instructions Regular & Impact 72 x 80 72 x 82 72 x 96 96 x 80 96 x 82 96 x 96 Impress the Weather KD Patio Door Regular & Impact Sizes 72 x 80 72 x 82 72 x 96 96 x 80 96
More informationHR175 Sash Replacement Kit Installation Instructions
HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure
More informationINSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;
More informationSpecialty Glass Measuring Instructions Claim Number **ALL INFORMATION IS REQUIRED. INSUFFICIENT OR INCOMPLETE FORMS WILL DELAY THE
Out-of-Warranty 3500-4300-8500-9555 Specialty Glass Measuring Instructions Claim Number 3500 Series 4300 Series 8500 Series 9555 Series **ALL INFORMATION IS REQUIRED. INSUFFICIENT OR INCOMPLETE FORMS WILL
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More information(Non Handed Kits) Slotted Hand Screwdriver. Power Driver & Bits. Work Gloves
Patio Door Kit Assembly Instructions -- 2-Panel Patio Door with Non-Assembled Frame and Assembled Sash Panels. (Non Handed Kits) Project Requirements: ~ This door was manufactured for installation into
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More informationCurtain Wall Installation Guide
Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More information890 SERIES PIVOT STEAM DOOR
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 890 SERIES PIVOT STEAM DOOR Copyright Alumax Bath Enclosures 1997. All rights reserved.
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationAluminum Clad Wood Window Field Mulling and Stacking Instructions
Aluminum Clad Wood Window Field Mulling and Stacking Instructions Mulling Stacking Mulling and Stacking IMPORTANT: Please read before you begin. TABLE OF CONTENTS AND TOOL / MATERIAL REQUIREMENTS START
More informationMira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions
PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)
More informationMULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION
MULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION TOOLS AND SUPPLIES 1 TOOLS CHECK LIST 1. laser level 2. hammer 3. pry bars 4. ladders 5. utility knife 6. screw gun 7. applicator foam gun 8. "j"
More information675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure
INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully
More informationVinyl Windows and Doors Manufactured by Pella Corporation
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V981255 2009 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020)
for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020) Thank you for selecting jeld-wen products. Attached are jeld-wen s recommended installation instructions for Premium Aluminum
More informationInstallation Recommendations for Finless Frame Doors
Installation Recommendations for Finless Frame Doors These installation recommendations are made available by MI Windows and Doors, LLC (MI) to assist with the integration of finless or flange sliding
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español
More information