Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit:

Size: px
Start display at page:

Download "Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit:"

Transcription

1 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to using alternative installation methods, hardware, or materials. DO NOT USE: Loctite, SuperGlue, or similar products on the hardware or the fl ares. B) Fit: Verify the fi t of the fl ares to vehicle. (Some fi ling, sanding, or cutting may be necessary to ensure proper fi t). C) Painting: (Optional) if paint is desired it must be done prior to installing fl ares on vehicle. Clean outer surface with a good grade degreaser. DO NOT USE LACQUER THINNER OR ENAMEL REDUCER AS A DEGREASER. Wipe outer surface thoroughly with a tack rag prior to paint. Application of plastic adhesion promoter for ABS plastic as per your paint system manufacturer s recommendations is required. Paint fl ares using a high quality enamel, or polyurethane automotive paint. If painting edge trim (not recommended), use a fl ex additive. D) Performance: Using larger Tires may increase the area required to turn the vehicle. Some Tire/Rim combinations may require lowering bump stops and or installing steering stops to prevent tire from contacting fl are. E) Exhaust System: Modifi cations may be necessary to maintain a minimum 4 clearance between fl ares and exhaust pipes. (Exhaust gases should not vent directly onto fl ares) F) Metal Protection: All exposed fasteners and bare metal should be treated with rust resistant paint BEFORE installing fl ares. Spray inner fender wells with undercoating AFTER fl are attachments have been completed. G) Decals: Flares may interfere with existing decals on vehicle. If you wish, remove decals prior to installation of fl ares. H) Care & Cleaning: Bushwacker fender fl ares are built to last; any detergent you use to wash your vehicle is suffi cient to clean the fl are. Do not use any harsh abrasive detergents. Jeep Cut-Out Fender Flares Set of 4 Set Part # Rev-20 03/01/2016 For complete fitment info visit : TOOLS FOR EASY INSTALLATION: Adhesions Remover (optional) Electric Drill 3/16 Drill Bit Grease Pencil Angle Grinder Recipricating Saw Cut Off Wheel #2 Phillips Bit Hammer 10mm Socket 7mm Socket Awl NOTE: These instructions involve cutting parts of the vehicle. It is important to read all instructions prior to cutting and installing of flares. PLEASE READ: Dirt and debris can become lodged between the fender fl ares and the vehicle s fenders, causing scratching and paint wear from vibration. Lund International is not responsible for any damage, and the installation of our fender fl ares is done with the buyer s understanding that this scratching and paint wear may occur. LIMITED LIFETIME WARRANTY AGAINST ANY MANUFACTURING DEFECTS To claim a warranty, you must provide Proof of Purchase. Included in Hardware Kit: pc 264 inches 36 pcs 20 pcs 36 pcs 1 pc IMPORTANT NOTE IF INSTALLING THIS APPLICATION ON A 96-UP VEHICLE: YOU WILL NEED TO MODIFY THE REAR BUMPER COVER AND TAKE CAUTION NOT TO DRILL THE WASHER FLUID RESERVOIR ON THE FRONT DRIVER SIDE.

2 STEP 2 - EDGE TRIM INSTALLATION A. If painting fl ares, see section C of Step 1 - Prior to Installation. Peel two to three inches of red vinyl backing away from Edge Trim (GP1-0005) tape. Applying the adhesive side of the edge trim to the inner side of the fl are, affi x the edge trim to the top edge of the fl are (the portion that comes in contact with the vehicle). B. Press edge trim into place along the top edge of the fl are in one-foot increments, pulling red vinyl backing free as you continue to work your way around the top edge of the fl are. Front Flare Installation Procedures (Driver s Side): 1 2 Remove the front factory fl are starting with the lower rear factory fastener, using a 7mm socket. Using a 10mm socket, remove the factory fastener located inside the top front of the fender well. 3 4 Using a 10mm socket, remove two factory fasteners underneath bumper on either side. Remove fascia piece Apply adhesive remover to the Cherokee emblem for ease of removal. Using a putty knife, carefully remove the Cherokee emblem, taking caution not to scratch the paint.

3 5 6 Using a grease pencil, make a horizontal line horizontally from the bottom of the headlight bezel to the inside of the fender well opening. Starting at the bottom of the headlight bezel, measure in 5 and mark a line on the fender 7 8 Trace a line from the mark made in Step 6 up along the contour to the third factory hole (counting from bottom front). From there, angle the line toward the edge of the fender. Starting at the edge of the door seam, measure in (towards fender well opening) 5-1/4 and make a mark Trace a line from the mark made in Step 8 up along the contour to the third factory hole (counting from bottom rear). From there, angle the line toward the edge of the fender. Starting at bottom rear of fender, cut along lines using a reciprocating saw or grinder. Note: it is helpful to use a block of wood to separate the fender from the splash guard, which will be trimmed later.

4 11 12 Cut along the horizontal line made in Step 9. Cut along the line made at the front of the fender, starting at the top. Note: Use a block of wood to separate the fender from the splash shield and to protect the bumper Cut along the horizontal line made in Step 7. Carefully cut along the line parallel to the bottom of the headlight bezel, taking care not to cut the bezel or the bumper CUT Carefully cut lower sheet metal strut attached to fender. At the rear of the front fender, using the cut sheet metal edge as a guide, mark the inner sheet metal structure to match.

5 17 18 Using a reciprocating saw, cut away the inner sheet metal as marked in Step 16. Grind the sheet metal back so that it is in line with the cut fender Grommet Trim the plastic splash guard to match the contours of the sheet metal. At the front of the splash shield, draw a line from the area cut in Step 19 down to the plastic grommet, taking care not to cut through the grommet. Trim on this line Fold the remaining fl ap under the bumper. The fender should look like this. Some additional grinding may be needed. Optional: Use caulking to seal all cut edges and seams.

6 23 24 Hold the Front Flare in place on the fender, pressing fi rmly. Using the holes in the part as a guide, mark hole locations on fender (9 places). Drill marks with a 3/16 bit Insert a supplied Torx screw (SW1-0045) through each pocket in fl are. Place a 3/8 thick rubber spacer (SP1-0009) on each screw from the backside of the pocket. Threads must protrude through spacer for proper attachment of fl are. All spacers must be installed prior to installation on fender Start each screw with a T45 Torx bit (SW1-0052) in each pocket but do not tighten until all screws have been started. NOTE: Over-tightening screws may cause them to strip! Use a Torque setting of 24 inch/ ounces. Optional: To secure splash shield, drill a hole and use a zip tie to attach it to the bumper.

7 Rear Flare Installation Procedures (Driver s Side): Remove the factory fl are starting with removal of the lower rear factory fastener, using a 7mm socket. Using a 10mm socket, remove the factory fastener located inside the front of the wheel well Using a 7mm socket, remove the lower front factory fastener. At bottom front of wheel well opening, measure in 2 and make a mark using a grease pencil Follow contour up to 1 past the door edge, maintaining a distance of 2 from edge of wheel well. Make a vertical line 1 back from door edge, intersecting with line made in Step 33.

8 35 36 At bottom rear of wheel well opening, measure in 1-5/8 and make a mark. Trace a line from the mark made in Step 35 up along the contour to the third factory hole (counting from bottom rear). Drop line down to intersect hole Measure up 3/8 from edge of fender well, intersecting with line made in Step 34 and mark a line continuing along edge of fender until intersecting with line made in Step 36. Starting at top of fender, cut along lines using a reciprocating saw or cut-off wheel Along rear fender well edge, take care not to cut through weld seam. Cut close to seam, then grind back. The weld seam should look like this.

9 41 42 Along front fender well edge, cut through sheet metal down to the fl are-out feature at the bottom. Carefully cut only the outer sheet metal layer from the fl are-out feature down, leaving the inner sheet metal layer intact Using a hammer or mallet, pound the inner sheet metal layer over the seam. Grind back excess metal as needed. Trim the inner wheel well to match the contours of the sheet metal The fender should look like this. Some additional grinding may be needed. Optional: Use caulking to seal all cut edges and seams. Open door. Install cover piece over dog leg using fi ve supplied drill screws (SW1-0066). Place drill screw in indent in part and drill into sheet metal. NOTE: Some trimming may be required.

10 47 48 Hold the Rear Main Flare on the fender, aligning with door seam and fender contours. Press fi rmly. Using the holes in the part as a guide, mark hole locations on fender (5 places). Drill marks with a 3/16 bit Insert a supplied Torx screw (SW1-0045) through each pocket in fl are. Place a 3/8 thick rubber spacer (SP1-0009) on each screw from the backside of the pocket. Threads must protrude through spacer for proper attachment of fl are. All spacers must be installed prior to installation on fender Start each screw with a T45 Torx bit in each pocket but do not tighten until all screws have been started. Over-tightening screws may cause them to strip! Use a Torque setting of 24 inch/ounces. Hold the Rear Door Piece on the door, aligning with the Rear Main Flare. Press fi rmly to ensure proper hole location alignment.

11 53 54 Using the holes in the part as a guide, mark hole locations on fender (4 places). Open Door. Drill marks with a 3/16 bit Insert a supplied Torx screw (SW1-0045) through each pocket in fl are. 57 Place a 3/8 thick rubber spacer (SP1-0009) on each screw from the backside of the pocket. Threads must protrude through spacer for proper attachment of fl are. All spacers must be installed prior to installation on fender. 58 Drill Screws Start each screw with a T45 Torx bit in each pocket but do not tighten until all screws have been started. Over-tightening screws may cause them to strip! Use a Torque setting of 24 inch/ounces. Optional: There are extra drill screws (SW1-0066) supplied in the kit. If desired, further secure the rear of the rear fl are using drill screws. Place drill screw on part and drill into sheet metal.

12 59 60 Using fl at end of supplied Edge Trim Tool, seat bottom edge of edge trim fi rst by inserting straight fl at end between bottom edge of edge trim and part at one open end and slide over entire top edge to the other end. If your vehicle has factory trim: Using curved end of supplied Edge Trim Tool, seat top edge of edge trim fi rst by hooking curved end under top edge at one open end and slide over entire top edge to the other end. 1 2 Prior to marking hole locations, hold the Flare on the fender, pressing fi rmly. Making sure the fl are is properly positioned, trace the outline of the fl are on the factory trim. Use a putty knife to separate the factory trim from the fender, stopping at line made in Step 2. 3 Use a utility knife to cut factory trim and discard.

Jeep Cherokee 4-Door XJ Set Part # Rev

Jeep Cherokee 4-Door XJ Set Part # Rev Jeep Cherokee 4-Door XJ Set Part # 10911 Rev-14 04-05-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.

More information

Jeep Cherokee Door XJ Set Part # Revision J

Jeep Cherokee Door XJ Set Part # Revision J Jeep Cherokee 84-96 4 Door XJ Set Part # 10911 Revision J 6-5-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

Toyota Extend-A-Fender Fender Flares Set of 4

Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Cut-Out TM Fender Flares Set of 4

Toyota Cut-Out TM Fender Flares Set of 4 Toyota Cut-Out TM Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Dodge Pocket Style Fender Flares Set of 4

Dodge Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Chevrolet Pocket Style Fender Flares Set of 4

Chevrolet Pocket Style Fender Flares Set of 4 Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

Ford Cut-Out Fender Flares Front Pair

Ford Cut-Out Fender Flares Front Pair Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Toyota Pocket Style Fender Flares Front Pair

Toyota Pocket Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Pocket Style Fender Flares Set of 4

Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Extend-A-Fender Fender Flares Set of 4

Toyota Extend-A-Fender Fender Flares Set of 4 Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

RAM OE Style Fender Flares Set of 4

RAM OE Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Cut-Out Fender Flares Rear Pair

Ford Cut-Out Fender Flares Rear Pair Ford Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Chevrolet Cut-Out Fender Flares Set of 4

Chevrolet Cut-Out Fender Flares Set of 4 Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Chevrolet Pocket Style Fender Flares Set of 4

Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Rear Pair

Included in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Rear Pair A) B) C) D) E) F) G) H) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according

More information

Chevy Pocket Style Fender Flares Set of 4

Chevy Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Pocket Style Fender Flares Set of 4

Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: 1. Jeep. Pocket Style Factory Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit: 1. Jeep. Pocket Style Factory Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Cut-Out Fender Flares Front Pair

Ford Cut-Out Fender Flares Front Pair Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

RAM Pocket Style Fender Flares Front Pair

RAM Pocket Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 1/22/2016

Included in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 1/22/2016 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 2/17/2016

Included in Hardware Kit: GMC Boss Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-7 2/17/2016 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Chevrolet Pocket Style Fender Flares Set of 4

Chevrolet Pocket Style Fender Flares Set of 4 Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

Ford Extend-A-Fender Fender Flares Set of 4

Ford Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Extend-A-Fender Fender Flares Set of 4

Toyota Extend-A-Fender Fender Flares Set of 4 Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

Chevrolet Cut-Out Fender Flares Front Pair

Chevrolet Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Chevrolet Street Flares Fender Flares Set of 4

Chevrolet Street Flares Fender Flares Set of 4 Chevrolet Street Flares Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

GMC Cut-Out Fender Flares Front Pair

GMC Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

GMC Pocket Style Fender Flares Set of 4

GMC Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Pocket Style Fender Flares Set of 4

Toyota Pocket Style Fender Flares Set of 4 Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Chevrolet Street Flares Fender Flares Rear Pair

Chevrolet Street Flares Fender Flares Rear Pair Chevrolet Street Flares Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

GMC Extend-A-Fender Fender Flares Set of 4

GMC Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 Ford Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Included in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:

Included in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION: 09-Up Ford F150 Set Part #20927-02 Rev-3 5-18-09 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

Included in Hardware Kit: Pocket Style Extended Coverage Fender Flares Rear Pair. Jeep

Included in Hardware Kit: Pocket Style Extended Coverage Fender Flares Rear Pair. Jeep Jeep Pocket Style Extended Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.

More information

STEP 1 PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:

STEP 1 PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION: STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Chevrolet Cut-Out Fender Flares Set of 4

Chevrolet Cut-Out Fender Flares Set of 4 Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

RAM OE Style Fender Flares Set of 4

RAM OE Style Fender Flares Set of 4 RAM OE Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Toyota Pocket Style Fender Flares Front Pair

Toyota Pocket Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

GMC Extend-A-Fender Fender Flares Set of 4

GMC Extend-A-Fender Fender Flares Set of 4 GMC Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

RAM Pocket Style Fender Flares Set of 2 (Rear)

RAM Pocket Style Fender Flares Set of 2 (Rear) STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION

Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION Toyota Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION Front Part #30922-02 Rev-1 7/18/2016 A) Bushwacker only approves installing the flares according to these written instructions with

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 Ford Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Ford Cut-Out Fender Flares Front Pair

Ford Cut-Out Fender Flares Front Pair Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Chevrolet Cut-Out Fender Flares Front Pair

Chevrolet Cut-Out Fender Flares Front Pair Chevrolet Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Included in Hardware Kit 4. Toyota Tundra, B- & D-Cab, CrewMax. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 4. Toyota Tundra, B- & D-Cab, CrewMax. Set Part # Rev STEP 1 PRIOR TO INSTALLATION A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Ford Cut-Out Fender Flares Set of 4

Ford Cut-Out Fender Flares Set of 4 Ford Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Toyota OE Style Fender Flares Set of 4

Toyota OE Style Fender Flares Set of 4 Toyota OE Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

RAM OE Style Fender Flares Front Pair

RAM OE Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

GMC Extend-A-Fender Fender Flares Set of 4

GMC Extend-A-Fender Fender Flares Set of 4 GMC Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Chevrolet Pocket Style Fender Flares Set of 4

Chevrolet Pocket Style Fender Flares Set of 4 Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:

More information

GMC Cut-Out Fender Flares Set of 4

GMC Cut-Out Fender Flares Set of 4 GMC Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Max Pocket Style Fender Flares Set of 4

Ford Max Pocket Style Fender Flares Set of 4 Ford Max Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Included in Hardware Kit. Volkswagen Amarok Pocket Style Fender Flares Set of 4 Set Part # / # Rev-3 02/07/2017

Included in Hardware Kit. Volkswagen Amarok Pocket Style Fender Flares Set of 4 Set Part # / # Rev-3 02/07/2017 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Chevrolet Cut-Out Fender Flares Set of 4

Chevrolet Cut-Out Fender Flares Set of 4 Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

RAM Pocket Style Fender Flares Set of 4

RAM Pocket Style Fender Flares Set of 4 RAM Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 Ford Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION Set Part #20942-02 Rev-4 07/05/2018 A) Bushwacker only approves installing the flares according to these written instructions with the hardware

More information

Included in Hardware Kit: Ford Extend-A-Fender Ford OE Style Fender Flares Set of 4 Set Part # Set Part # Rev-1 01/18/2017

Included in Hardware Kit: Ford Extend-A-Fender Ford OE Style Fender Flares Set of 4 Set Part # Set Part # Rev-1 01/18/2017 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

GMC Cut-Out Fender Flares Set of 4

GMC Cut-Out Fender Flares Set of 4 GMC Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to

More information

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Included in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION:

Included in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION: STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Toyota Tacoma Extended Cab/Standard Cab Set Part # Rev

Toyota Tacoma Extended Cab/Standard Cab Set Part # Rev Toyota Tacoma Extended Cab/Standard Cab Set Part # 31919 Rev-7 06-23-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the

More information

Included in Hardware Kit 4. Jeep Wrangler JK 4-Door Rear Flares. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 4. Jeep Wrangler JK 4-Door Rear Flares. Set Part # Rev STEP 1 PRIOR TO INSTALLATION A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to

More information

Included in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Front Pair

Included in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Rubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs

Rubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs Jeep Cherokee ZJ Set Part #10916-07 Rev-2 03-11-10 THESE INSTRUCTIONS INVOLVE CUTTING THE FENDERS OF THE VEHICLE. IT IS IMPORTANT TO READ ALL INSTRUCTIONS PRIOR TO THE CUTTING AND INSTALLATION OF THESE

More information

Cut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Cut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Ford F150 Rear Flares Set Part # Revision

Ford F150 Rear Flares Set Part # Revision Ford F150 Rear Flares Set Part # 20074 Revision 1 04-01-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.

More information

Jeep. Flat Style Fender Flares Front Pair Front Part # Rev-9 02/23/2016 For complete fitment info visit :

Jeep. Flat Style Fender Flares Front Pair Front Part # Rev-9 02/23/2016 For complete fitment info visit : STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep

Included in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.

More information

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit : Jeep Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Included in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION : 2011-2014 Ram 2500/3500 Fleetside 76.3 inch and 98.3 inch Bed. Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife 6. Awl or Similar Pointed Tool PRIOR

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Part#: TG-FF8G4158 FOR 2007-2013 GMC Sierra 1500 Pickup Truck (Exclude 69.3inch Short Bed Models) FENDER FLARE INSTALLATION Hardware Kit Included IMPORTANT TYGER only approves the installation according

More information

1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs

1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs 97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with

More information

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Wrangler YJ Fronts Set Part #10067-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Wrangler YJ Set Part #10924-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION : 2009 - UP Ram 1500 Fleetside. (Exclude R/T Models) Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife PRIOR TO INSTALLATION Hardware Kit Included 5/16

More information

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs

5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Plastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs

Plastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION TG-FF8T4178: Fit 2014-UP Toyota Tundra PRIOR TO INSTALLATION IMPORTANT Tyger only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

Dodge Dakota 2005 Quad Cab Set Part # Revision A

Dodge Dakota 2005 Quad Cab Set Part # Revision A Dodge Dakota 2005 Quad Cab Set Part # 51908 Revision A 2-17-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

Jeep Wrangler JK Door Rear Pair Part # Revision E

Jeep Wrangler JK Door Rear Pair Part # Revision E Jeep Wrangler JK 2007 4-Door Rear Pair Part # 10044 Revision E 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the

More information

Toyota FJ Cruiser 2006-Up Set Part # Revision A

Toyota FJ Cruiser 2006-Up Set Part # Revision A Toyota FJ Cruiser 2006-Up Set Part # 31924 Revision A 03-31-08 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

Jeep Wrangler JK & 4-Door Front Pair Part # Revision H

Jeep Wrangler JK & 4-Door Front Pair Part # Revision H Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with

More information