NOTES 3D VIEW OF RAILING WITH TYPE 1 - PICKET INFILL PANEL. (42" Height shown, 54" Height Similar) TABLE 1 - RAILING MEMBERS ALTERNATIVE BOTTOM &

Size: px
Start display at page:

Download "NOTES 3D VIEW OF RAILING WITH TYPE 1 - PICKET INFILL PANEL. (42" Height shown, 54" Height Similar) TABLE 1 - RAILING MEMBERS ALTERNATIVE BOTTOM &"

Transcription

1 NOTES C:\d\projects\standards\structures\current\ready4release\20book\00862-of8.dgn 5/2/202 0:0:6 M 0.2 MEMBER s Joint/Splice Sleeves Intermediate & Int. & Connection Sleeve Handrail Joint/Splice Sleeves Handrails Handrail Support Bar End Hoops Pickets (Type Infill Panel) Infill Panel Members (Types 2-5) TBLE NOTES: D VIEW OF RILING WITH TYPE - PICKET INFILL PNEL R " ROUND TOP CP RIL (4 Height shown, 54" Height Similar) TBLE - RILING MEMBERS LLOY () 606-T6 606-T6 606-T5 606-T5 606-T6 606-T5 606-T5 606-T6 606-T6 606-T6.090" LTERNTE TOP RIL SECTION DESIGNTION RT 2x2x NPS (Sch. 0) " Round Top Cap Rail 2 NPS (Sch. 0).00 OD x 0.25 Wall 2.50 OD x 0.25 Wall Top Cap Rail Inner Sleeve RT 2x2x OD x 0.25 Wall " NPS (Sch. 40) NPS (Sch. 40) " ˆ Roun " ˆ Roun () lloy 606-T6 or 606-T52 & T6 may be substituted for lloy 606-T5. (2) 0.88" wall thickness permitted for rails with post spacings less than 5 -. " 2 TOP CP RIL INNER SPLICE SLEEVE OUTSIDE DIMENSION 2.00" x 2.00" " 2.00" x 2.00" R " 2.500" 2.800".500"..900" 0.750" 0.750" 606-T5 Varies (See Details) Varies WLL THICKNESS 0.250" 0.20" " " (2) 0.250" " 0.4 N/ N/ Varies INTERMEDITE RIL SECTION FOR TYPE, 4 & 5 RILINGS LTERNTIVE BOTTOM & DESIGN LODS, GEOMETRY ND PPLICBILITY: See the Instructions for Design Standards for the design loads, geometry and applicability requirements. GENERL: dequate foundation support shall be provided for anchorage and stability against overturning. See Index No. 86 for special requirements and modifications for use on bridges. The railing shown on these drawings requires a handrail for ramps steeper than a 5% grade to conform with the requirements of the mericans with Disabilities ct (D). RILS, PNELS ND POSTS: Structural Extrusions, Tube, Pipe and Bar shall be in accordance with Table and STM B22 or STM B429. Top, bottom and intermediate rail corner bends with maximum 4-0" post spacing, may be lloy 606-T6. Perforated panels (Type 5) shall be lloy 00-H4. s shall be fabricated and installed plumb, " tolerance when measured at -6" above the foundation. Pickets and vertical panel elements shall be fabricated parallel to the posts, except that Type 2, & 5 panel infills may be fabricated parallel to the longitudinal grade. Corners and changes in tangential longitudinal alignment shall be made continuous with a bend radius or terminate at adjoining sections with mitered end sections when handrails are not required. For changes in tangential longitudinal alignment greater than 45, posts shall be positioned at a maximum distance of 2-0" each side of the corner and shall not be located at the corner apex. For curved longitudinal alignments the top and bottom rails and handrails shall be shop bent to match the alignment radius. BSE PLTES ND RIL CPS: s and Cap plates shall be in accordance with STM B209, lloy 606-T6. SHIM PLTES: Shim Plates shall be aluminum in accordance with STM B209, lloy 606 or 606. Shim plates shall be used for foundation height adjustments greater than " and localized irregularities greater than Field trim shim plates when necessary to match the contours of the foundation. Beveled shim plates may be used in lieu of trimmed flat shim plates shown. Stacked shim plates must be bonded together with adhesive bonding material and limited to a maximum total thickness of, unless longer anchor bolts are provided for the exposed thread length. NCHOR BOLTS: nchor bolts shall be in accordance with STM F554 Grade 6. Headless anchor bolts for dhesive nchors shall be threaded full length. Cutting of reinforcing steel is permitted for drilled hole installation. Expansion nchors are not permitted. ll anchor bolts shall have single self-locking hex nuts. Tack welding of the nut to the anchor bolt may be used in lieu of self-locking nuts. ll nuts shall be in accordance with STM 56 or STM 94. Flat Washers shall be in accordance with STM F46 and Plate Washers (for long slotted holes only), shall be in accordance with STM 6 or STM 709 Grade 6. fter the nuts have been snug tightened, the anchor bolt threads shall be distorted to prevent removal of the nuts. Distorted threads and tack welds shall be coated with a galvanizing compound in accordance with the Specifications. RESILIENT ND NEOPRENE PDS: Resilient and Neoprene pads shall be in accordance with Specification Section 92 except that testing of the finished pads shall not be required. Neoprene pads shall be durometer hardness 60 to 80. JOINTS: ll welded joints are to be ground smooth. Expansion joints shall be spaced at a maximum 5-0". Field splices similar to the expansion joint detail may be approved by the Engineer to facilitate handling, but top rail must be continuous across a minimum of two posts. WELDING: ll welding shall be in accordance with the merican Welding Society Structural Welding Code (luminum) NSI/WS D.2 (current edition). Filler metal shall be either ER58, ER556 or ER5556. Nondestructive testing of welds is not required. Filler metal for plug welds and bend splices may be ER404. COTINGS: The aluminum railing shall be mill finish unless otherwise noted in the Contract Documents. ll nuts, bolts and washers shall be hot-dip galvanized in accordance with Specification Section 962. SHOP DRWINGS: Complete details addressing project specific geometry (line & grade) showing post and expansion joint locations, post and panel type, anchor bolt installation "Case" or lengths, must be submitted by the Contractor for the Engineer s approval prior to fabrication of the railing. Shop drawings shall be in accordance with the Specifications. PYMENT: Railing shall be paid for per linear foot (Item No abb). Payment will be plan quantity measured as the length along the center line of the top rail, and includes rails, posts, pickets, panels, rail splice assembly, base plates, anchor bolts, nuts, washers, resilient or neoprene pads and all incidental materials and labor required to complete installation of the railing. LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

2 Spacing - 5-8" (Max.) ~ Type "B" Only 54" Special Height Bicycle Railing (SHBR) End Hoop 5-8" (Max.) ~ Type "" or 7 -" (Max.) ~ Type "B" 4 Pedestrian/Bicycle Railing (PBR) Rail Expansion Joint see Detail "B", Sheet 4 Infill Panel Type Varies, See Data Table in Plans (Pickets Shown) 7 " ( 0" ~ " Max. Gap 54" Special Height Bicycle Railing 4 Pedestrian/Bicycle Railing R Max. See Detail "", Sheet 4 Equal Clear Openings at s 2 " ~ 5 " Max. ( Top of Intermediate Rail 2-7 " ( -9 " (S Top of Sidewalk or Bikeway Ground Line -0" Bottom & Intermediate Rail Minimum from free end of concrete and expansion joints Foundation Expansion Joint * " Clear Opening (See Geometry Notes, Sheet ) 6" V-Groove or Construction Joint Offset Rail expansion joints to be located in panels above structure expansion joints * (5-0" maximum spacing). ELEVTION (Showing Outside Face of Railing with Type "" s) TYPICL RILING DETILS & RILINGS ON GRDES 0% TO 5% (Type - Picket Railing Shown, Other Types Similar) Note: Non-continuous corners are permitted when handrails are not required. EXPNDED ELEVTION T CORNERS DETIL FOR NON-CONTINUOUS RILING T CORNERS NOTES: * Keyed construction joints in Index No. 60 Gravity C:\d\projects\standards\structures\20book\ of8.dgn Wall are not considered to be expansion joints. Spacing 5-8" (Max.) ~ Type "B" Only 5-8" (Max.) ~ Type "" or See Plans for 7 -" (Max.) ~ Type "B" continuation or termination limits -6" of railing 4-6" Special Height Bicycle Railing -6" Pedestrian/Bicycle Railing 2-0" " (SHBR) (PBR) 2-6" Max. Handrail required for ramps (Handrail continuous at landings between runs) Handrail ~ NPS Sch. 40 Horizontal handrail extension at landing See "Typical Railing Details" for post, rail & picket or infill panel details 0-0" Max. for Slopes > 6.25% 40-0" Max. for Slopes = 6.25% Grade -6" 2-6" Max. 2-0" " Top of Sidewalk 5-0" See Plans for continuation or termination limits of railing 6/28/202 :8:0 M 6-0" Bottom Landing 0-0" Max. for Slopes > 6.25% 40-0" Max. for Slopes = 6.25% Ramp 5-0" Intermediate Landing ELEVTION (Showing Inside Face of Railing with Type "" s) RILINGS ON GRDES STEEPER THN 5% (Type - Picket Railing Shown, Other Types Similar) Ramp RMP REQUIREMENTS For slopes greater than 5%: Max. ramp slope = 8.% Max. ramp cross-slope = 2.0% Top Landing LNDING REQUIREMENTS Max. landing slope = 2% Max. landing cross-slope = 2% LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

3 7 -" (Max.) ~ Pedestrian/Bicycle Railing Varies ~ Equal spacing 5-0" Max. on Steps -6" Handrail Equal to one Extension tread length See "Typical Railing Details", Sheet 2 for post, rail & picket details -6" 2-0" R 6" -6" Cap VIEW J-J " Rail Cap Round over corners J J DETIL "J" - ELEVTION VIEW 8 TOP RIL TERMINTION Seal Weld Cut rail sleeve to match inside Bottom face of post or weld rail Rail directly to post " DETIL "K" - ELEVTION VIEW BOTTOM RIL CONNECTION R 8" Rail Termination (End Cap) or Splice when rail continues on (shown dotted) -6" 0" " Max. C:\d\projects\standards\structures\20book\00862-of8.dgn 6/28/202 :8:2 M -6" Handrail termination See Detail "L" 2-0" -0" 6 Concrete sidewalk to extend 6" min. behind ra RILING CONTINUTION BEYOND STEPS OR STIRS -6" Handrail Extension R 6-0" Bottom Landing (Bottom shown, Top similar) R DETIL "L" - PLN VIEW HNDRIL TERMINTION Rail Termination (End Cap) Equal to one tread length Not considered an expansion joint for railing fabrication See Index No. 52 or Contract Plans for Step Details Varies ~ Equal spacing 5-0" Max. on Steps () Wide cheekwall both sides See Index No. 52 or Contract Plans for Step Details See "Typical Railing Details", Sheet 2 for post, rail & picket details " 6-0" Max. for one run of steps R 6" luminum Handrail required for three or more steps (Handrail and cheekwalls continuous at landings) Handrails ~ NPS (Sch. 40) pipe Handrail Continuous t Landing 2-0" Bottom of cheekwall 5-0" Length Of Landing ELEVTION (t-grade Steps shown, Elevated Stairs similar) RILINGS ON STEPS & STIRS " RIL TERMINTION DETILS -6" Equal to one tread length -6" Handrail Extension 2-0" -6"+ 2-0" Leveling Channel see Detail, Sheet 4-0" Equal to one tread width () Wide cheekwall both sides See Index No. 52 or Contract Plans for Step Details " termination see Detail "J" Handrail Termination, See Detail "L" -0" -6" 2-0" " Max. permitted Top Landing R 6" termination, -6" first panel at top of stairs Length of Landing 5 LTERNTE END TRETMENT " -6" 2-0" see Detail "K" LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

4 C:\d\projects\standards\structures\20book\ of8.dgn 6/28/202 :8:4 M Top & nchor Bolt Rail or Handrail Section SECTION - 2 " SECTION B-B ( Connection) R (Handrail Connection) Intermediate Rail Set Screws * s Optional shape shown dashed Hand & Bar " ˆ (Intermediate Rail Connection) SECTION C-C SECTION D-D Intermediate Rail Sleeve & nchor Bottom Rail Sleeve ( Connection) Handrail or Neoprene Pad " " ˆ " Thick Resilient (centered) " Steel " (Beve to Bas 6" ** 6" Top & Handrails ( " ( Hole both ends Po Bolt " Plate ") ~ Expansion Joint ") ~ Field Splice Slip Joint Round over of rails " (T ROUND RILS - TOP RIL OR HNDRIL ( at Expansion Joint Shown) " " 4" PLTE WSHER DETIL TOP VIEW Rail or Handrail " Plate LEVELING CHNNEL DETIL (Front & Back) (Si luminum Sleeve " 2 " 2 Leveling Channel x x 4" wall " Max. Base Pl & nchor 8" BSE PLTE " Base Pla nchor Bolt H to Stiffene Bas "B" (shown dotted) Po Bolt SECTION G-G - BSE PLTE DETILS " ( ") ~ Expansion " ( ") ~ Field Splice Intermediate or DETIL "B" - EXPNSION JOINT (FIELD SPLICE SLIP JOINT SIMILR) 8" SHIM PLTE DETIL Match slope of " " Level SIDE VIEW Cope to clear welds 6" 5 8 F Stif " R for Type "B" - s " ˆ Base Pla nchor Bolt Ho Leveling Channel shown dashed (see Detail) SQURE RILS - INTERMEDITE OR BOTTOM RIL ( Shown at Expansion Joint Shown) Type "B" Stiffene 7 7 8" 2 8" 2 8 " 8 " " 2 8 " 2 8 " 8 " (Vertical Typ.) 4-6" Special Height Bicycle Railing -6" Pedestrian/Bicycle Railing BSE PLTE B ( Option) Set Screws * F Flatten end of End Hoop to Max. width 2 " (T "B" (shown dotted) " " 6" C C D D " holes in posts. -0" luminum Sleeve through Intermediate or Type "" Intermediate Rail Pickets 4 4" G DETIL " POST "B" STIFFENER 6" 8 4" R Mitered Section (Typ. ll Rails) Set Screw * DETIL "" - RIL CONNECTIONS (Pickets/Panels Not Shown for Clarity) G (Bevel bottom & top of post as required to maintain plumb posts) NOTES: Leveling Channel - R Cope Permitted VIEW F-F " ˆ Hole ( O INTERMEDITE OR BOTTOM RIL - " Slit (Bottom Side O luminum Sleeve:.50 OD x 0.25 Wall for Intermediate and s LUMINUM SLEEVE DETIL (Bottom Side Shown) CROSS REFERENCE: Handrail (see Detail Sheet ) ~ for slopes = 8.% B ~ for slope > 8.% Leveling Channel for slopes > 5%. Stairs shown, Steep Ramp similar (Ramps - Bolts normal) use " ˆ for nchor Bolts with Flat Washers for slopes = 8.%. B (Stairs - Bolts plumb) use " ˆ nchor Bolts with Beveled Plate and Washers for slopes > 8.% to 5%; use " x " Slotted Hol * " ˆ x " Pan Head luminum (lloy 2024-T4 or 707 or Stainless Steel (Type 6 or 8-8 lloy) Set Screws. Screws must be set flush against the outside face of rails & posts and underside of handrails. single " ˆ weld may be substituted for the Set Screws. ** Embedded length may be 4" for plug welded connection. For location of Details "B", See Sheet 2. G B B G 2-0" -6" LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 07/0/

5 P 6 O.C. (Max.) Picket Spacing * Intermediate Rail " " ˆ Max. Hole for R " ˆ Max. Hole for St 4" 7 P 0 0 Picket ~ " ˆ Bar ( DETIL "" Optional Welded Connection at end picket Optional Welded Connection at end picket 2-7 " ~ ( -9 " ~ (S See Detail "" (Top of Picket Connection) & nchor Picket ~ " ˆ Bar ( " ˆ Max. Hole for R " ˆ Max. Hole for St " Thick Resil or Neoprene Pad " Nominal Opening Equal Clear Openings at s 2 " min. ~ 5 " max. ( Equal Clear Openings at s 2 " min. ~ 5 " max. ( SECTION - See Detail "B" nchor Bolt DETIL "B" (Bottom of Picket Connection) TYPE - PICKET INFILL PNEL PICKET NOTES: * Picket Spacing of 6 " centers is based on a " NPS for standard applicat When shown in the Contract Plans a 4 picket spacing may be required. If an alternate design is used, maintain a maximum clear opening of 5 " standard installations and " for special conditi Chain-Link Fence C:\d\projects\standards\structures\20book\ of8.dgn Chain-Link Fence Fabric ( Mesh x No. 9 Gage wire with knuckled top and twisted bottom selvage) -0" center ( and End Rail) Fabric tied to inside face of railing 0 4" (PBR) " (S TBLE 2 - CHIN-LINK PNEL COMPONENT MTERILS COMPONENT Chain-Link Fence Fabric ( mesh with twisted bottom and knuckled top selvage) Tie Wires Tension Bars STM F 668 F 626 F 626 COMPONENT INFORMTION Zinc-Coated Steel - No. 9 gage (coated wire diameter), Class 2 Coating luminum-coated Steel - No. 9 gage (coated wire diameter) Polyvinyl Chloride (PVC) Coated Steel - No. 9 gage Zinc-Coated Wire (metallic-coated core wire diameter) ~ See Plans for specified color of PVC. Zinc-Coated Steel Wire - No. 9 gage with coating to match Chain-Link Fence Fabric. 6" (min. thickness) x 4" (min. width) x 2 - (min. height) Steel Bars Miscellaneous Fence Components F 626 Zinc-Coated Steel 2-0" center (Intermediate & ) SECTION - CHIN-LINK PNEL NOTE: Chain-Link Fence Fabric shall be continuous along limits of railing. 6/28/202 :8:7 M TYPE 2 - CHIN-LINK (Continuous Infill Panel) NOTES:. See Plans for Infill Panel option required. Splicing of Chain-Link panels using Tension Bars at 20-0" minimum increments is permitted. LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

6 2 - (PBR) (SHBR) - Square Bar (Rays) Channel xx ( 4 -" R Channel See Detail "" See Detail "C" Rail Square Bar (Rays) DETIL "" #0x " ( " sp. Channel Front & Back Face Only Square Bar (Rays) DETIL "B" "x " F Strips #0x " ( " sp. INTERMEDITE RIL/RY BOTTOM RIL/RY CONNECTION CONNECTION Square Radial Center -"R? SECTION - See Detail "B" Square Bar (Rays) "x " Pu sp. Bar (Rays) Channel x (rc) Max. "x " Pu sp. Notch rc at Side Channel -6 4" TYPE - SUNSHINE INFILL PNEL Channel x (rc) DETIL "C" RY/RC CONNECTION ~ #0x " (8-8 -0" sp. DETIL "D" C:\d\projects\standards\structures\20book\ of8.dgn 6/28/202 :8:20 M 2-0" (PBR) Panel Height -0" (SHBR) " (PBR) 8 " 5 " 9 6" (SHBR) - 52 " Infill Channel (Cut or Cast) C C B B 8" R (PBR) -0" R (SHBR) 2 (PBR) " (PBR) - (PBR) Panel Width " (S (SHBR) - (SHBR) Gap Varies 2-8" R (PBR) 4-0" R (SHBR) 4" Max. TYPE 4 - BRODWY INFILL PNEL NOTES:. See Plans for Infill Panel Option required. See Detail "4" " Infill SECTION - Inside Face of Rail Channel " Infill DETIL "4" #0x " ( " sp. "x " F Strip RC/POST CONNECTION Panel Mullion " Panel " PNEL/RIL CONNECTION (Top Shown, Bottom Similar) SECTION C-C PNEL/SPLICE CONNECTION End Panel " " " " Lengthen border and trim top & bottom of panels to match grade. " (PBR) (SHBR) " (Ramp) Max. (Stairs) (Ramp) PNEL DJUSTMENT FOR RILINGS ON GRDES ~ #0 Gap Varies Pan 4" Max. (8-8 -0" sp. "x " F Strip " Panel SECTION B-B PNEL END CP LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

7 2-0" (Panel Height) 4 Pedestrian/Bicycle Railing 54" Special Height Bicycle Railing -0" (Panel Height) Perforated Panel (0.04" ) C Channel Panel Mullion C See Detail " Perforated Panel (0.04" ) Inside Face of Rail #0x " (8-8 Channel 2-0" sp. "x " F Strip Perforated Panel (0.04" ) DETIL " PNEL/RIL CONNECTION (Top Shown, Bottom & Sides Similar) Perforated Panel Panel Mullion (0.04" ) SECTION - 6/28/202 :8:2 M C:\d\projects\standards\structures\20book\ of8.dgn REPETING PTTERN DETIL FOR PEFORTED PNEL -0" Max. -0" Max. (Panel Width) (Panel Width) "x " F Strip TYPE 5 - PERFORTED INFILL PNEL " SECTION C-C PNEL/SPLICE CONNECTION LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 0/0/

8 See Section - Sheet 4 5-0" Std. ~ -0" Clear Between Handrails 4 Bolts & Bolts & 4" Sidewalk with Thickened Edge Slope 2% Max. (away from drop-off) 6" 54" ~ Special Height Bicycle Railing 4 ~ Pedestrian/Bicycle Railing 4" (Case IIa) 4 (Case IIb) Bolts & See Detail "C" Slope 2% Max. (away from drop-off) Top of step nosing 4 ~ Pedestrian/Bicycle Railing 2-0" Measured from Step Nosings 4 NPS (Sch. 40) Handrail " Drop-off (Varies) Reinforced Concrete Structure Step Cheekwall Varies ( Required for Stability of Railing) 8" Width at TYPICL SECTION ON STEPS & STIRS (Case III) Top of Wall C:\d\projects\standards\structures\20book\ of8.dgn 6/28/202 :8:26 M TYPICL SECTION ON CONCRETE SIDEWLK TYPICL SECTION ON RETINING WLL (Case I) ~ " ˆ C-I-P Hex Head nchor Bolts, or " ˆ Headless nchor Bolts set with an dhe Bonding Material System in accordance with Specification Sections 46 and 97. Self-Locking Hex Nut & Washer. Place nchor Bolts perpendicular to Base Grades = 8.% (Ramps) with flat washer. Place anchor bolts plumb for grades > 8. (Stairs) with flat washer & beveled washer, or leveling channel. Edge Shim (8" long Shim Plates as required x " wide x thickn as Reqd.) Full size Shim Plates when required for height adjustment () wide " Thick Resilient bed of dhesive or Neoprene Pad Bonding Material DETIL "D" (OPTIONL SHIMMING DETIL DETIL "C" FOR CROSS SLOPE CORRECTION) (Cast-In-Place nchor Bolts shown, (Used in lieu of Beveled Shim Plates) dhesive nchors similar) "C" Embedment (Case II) & nchor Washers or Leveling Channel " Thick Resilient or Neoprene Pad Minimum 2 ~ #4 Bars in Top of Structure for Case IIa & III Minimum #4 -0" (Max.) spacing for Case IIa "" "B" () () Inside Face of Concrete Structure or Sidewalk (See Concrete Structure Plans for actual dimensions and reinforcing details) CSE I IIa IIb III STRUCTURE TYPE Unreinforced Concrete Reinforced Concrete Gravity Wall Index No. 60 Step Cheekwall NCHOR BOLT TBLE "" Edge Dist. 4 4 DIMENSIONS "B" "C" Edge Dist. Embedment Head Bolt 6" top 4-0" * * Embedment length "C" may be reduced to for the 4 height 4" railings for Case IIb, when the post spacing does not exceed 5-0". 4" NCHOR LENGTH C.I.P Hex NCHOR dhesive SIZE nchor " " - " " " " " LST FDOT DESIGN STNDRDS LUMINUM PEDESTRIN/BICYCLE RILING 07/0/

ALUMINUM PIPE GUIDERAIL 01/01/

ALUMINUM PIPE GUIDERAIL 01/01/ NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy

More information

STEEL PIPE GUIDERAIL 01/01/

STEEL PIPE GUIDERAIL 01/01/ NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports

More information

NOTES. 3D VIEW OF RAILING WITH TYPE 1 - PICKET INFILL PANEL (42" Height shown, 54" Height Similar) TABLE 1 - RAILING MEMBERS

NOTES. 3D VIEW OF RAILING WITH TYPE 1 - PICKET INFILL PANEL (42 Height shown, 54 Height Similar) TABLE 1 - RAILING MEMBERS NOTES :\d\projects\standards\structures\current\ready4release\20book\00852-of8.dgn 5/2/202 0:09:4 M D VIEW OF RILING WITH TYPE - PIKET INFILL PNEL (4 Height shown, 54" Height Similar) TLE - RILING MEMERS

More information

ALUMINUM PEDESTRIAN/BICYCLE RAILING

ALUMINUM PEDESTRIAN/BICYCLE RAILING MEMBER s (Type "" & "B") s (Type "") Top Plate (Type "") End Hoops Joint/Splice Sleeves Intermediate & Int. & onnection Sleeve Handrail Joint/Splice Sleeves Handrails Handrail Support Bar Pickets (Type

More information

PART MATERIALS. Section Fencing Materials. Description

PART MATERIALS. Section Fencing Materials. Description PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain

More information

APPENDIX FENCE GENERAL NOTES

APPENDIX FENCE GENERAL NOTES APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.

More information

(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" 8-0" 6-0" Truss Depth. 3" sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.

(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0 7-6 8-0 6-0 Truss Depth. 3 sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T. Column truss connection (See details sheets 3 & 4 of 10) \ Span (Odd number of panels) \ Span (Even number of panels) Back truss chord Top truss chord \ Truss Chord splice Truss depth (See details \ Left

More information

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"

More information

RAIL PANEL AT TRANSITION SECTION PLAN - POST DETAIL PLAN - TUBE SPLICE. Colorado Department of Transportation. Staff Bridge Branch

RAIL PANEL AT TRANSITION SECTION PLAN - POST DETAIL PLAN - TUBE SPLICE. Colorado Department of Transportation. Staff Bridge Branch Limits of pay length for Bridge RailType 10M (For post spacing, see Dwg. No. B ) B60610 (Use with B60610A) 8 min. 1 max. 8 min. 1 max. 10 0 Max. 10 0 Max. post spacing 10 0 Max. 2 5 Post 1 x 1 slotted

More information

WAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence

WAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised

More information

EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL

EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid

More information

5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.

5/16 Flange nut. Bolt Keeper Plate (8 Sq. SYS.) (3) 1/2 x 3 Hex head connector zinc plated bolt w/ washers and nut. Anchor 3 sq. 7 Ga. 2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc

More information

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified. 907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing

More information

TYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.

TYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0 7-6 NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T. Column truss connection Chord splice (see details (See details sheets 3 & 4 of 10) s Top truss chord Free end panel 10-0" Support end panels length varies (See chart below) \ Truss Back truss chord Top

More information

1.1 RELATED DOCUMENTS

1.1 RELATED DOCUMENTS SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections

More information

Project: # Solano Community College District

Project: # Solano Community College District ADDENDUM #02 Project: #16 007 Solano Community College District Horticulture Site Improvements Date: April 26, 2016 The following clarifications are provided based on questions received or changes in District

More information

SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP

SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP 1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of

More information

Horizontal Cable Systems

Horizontal Cable Systems ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:

More information

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available. SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

24" B B Joint X501 Joint See MARKINGS Note PCB-RXX-350-TL3 " X501 Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOT

24 B B Joint X501 Joint See MARKINGS Note PCB-RXX-350-TL3  X501 Y301 (Typ.)  A PLAN (reinforced casting option shown) A  dia. Hinge Bar (Typ.) NOT B B Joint Joint See MARKINGS Note PCB-RXX-350-TL3 " Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOTES GENERAL: This barrier may be manufactured with reinforcing steel

More information

SECTION CHAIN LINK FENCING AND GATES

SECTION CHAIN LINK FENCING AND GATES PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide chain link fencing and gates as Shown on the Contract Drawings

More information

HEADED ANCHOR BOLT OPTION

HEADED ANCHOR BOLT OPTION Ground Rod 18" min. Depth, 2 Required nchor Bolts. Number (min. 8) and Size as Required by Manufacturer. 6" to 12" Ground Line " dia. Conduit Number and Direction as Shown on Lighting Layout Sheets. Slope

More information

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018 SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

The following instructions will guide you through the installation of your new vinyl railing stair kit.

The following instructions will guide you through the installation of your new vinyl railing stair kit. Installation Guide Vinyl Standard Stair Railing Tools Required Protective eye glasses Tape measure Variable speed drill/screwdriver Rotary hammer or hammer drill and masonry percussion bit recommended

More information

BRIDGE RAILING, 4 TUBE B-26-F POST DETAILS MICHIGAN DEPARTMENT OF TRANSPORTATION

BRIDGE RAILING, 4 TUBE B-26-F POST DETAILS MICHIGAN DEPARTMENT OF TRANSPORTATION \ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x 6" SLOTTED ROUND HEAD BOLTS, WITH 1 PLATE WASHER, 1 LOCK WASHER AND HEX. NUT \ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x

More information

Horizontal Cable Systems

Horizontal Cable Systems ALUMINUM RAILING INSTALLATION INSTRUCTIONS Horizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications: Confirm

More information

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO. 2012-16A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence,

More information

Item 550 Chain Link Fence

Item 550 Chain Link Fence Item Chain Link Fence 1. DESCRIPTION 2. MATERIALS Furnish, install, remove, repair, or replace chain link fence and gates. Furnish certification from the chain link fence materials manufacturer stating

More information

SIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD

SIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0, 8'-0, 10'-0 NOMINAL SPREAD Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"

More information

SECTION METAL FABRICATIONS

SECTION METAL FABRICATIONS SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM

More information

F-5-1a. Concrete Bollards (Detail 1 of 2) WEIGHT: 166kg. WEIGHT: 227kg. WEIGHT: 113kg. WEIGHT: 212kg

F-5-1a. Concrete Bollards (Detail 1 of 2) WEIGHT: 166kg. WEIGHT: 227kg. WEIGHT: 113kg. WEIGHT: 212kg Contents F-5-1a Concrete Bollards F-5-1b Concrete Bollards F-5-2 Concrete Bollards with City Logo F-5-3 Cast Iron Bollards F-5-4 Decorative Steel Bollard F-5-5 Swivel P Gate Steel Bollard F-5-6 Steel Bollard

More information

SIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP

SIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0, 8'-0, 10'-0 NOMINAL SPREAD (SEE CONTRACT) POLE CAP Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"

More information

City of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE

City of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE 1.0 GENERAL 1.1 Scope 1.1.1 The work shall consist of supply and installing chain link fence, including braces and gates, as shown on the plans and specifications at the locations designated by the Engineer.

More information

Ti-Color STAINLESS STEEL HANDRAIL

Ti-Color STAINLESS STEEL HANDRAIL Ti-Color STINLESS STEEL HNDRIL Handrail Custom-made Rail HNDRIL STNDRD Handrail Custom-made rail Vertical Type Horizontal Type Elegance Type HNDRIL TYPE Vertical Type 5001 / 6001 6002 / 7002 5004 / 6004

More information

AUXILIARY FRAMING AND ACCESSORIES

AUXILIARY FRAMING AND ACCESSORIES CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION

More information

Section 808. FENCING

Section 808. FENCING 808.01 Section 808. FENCING 808.01. Description. This work consists of providing and erecting, or moving existing, woven wire fence, temporary fence, protective fence, chain link fence, high-tensile wire

More information

Installation Instructions

Installation Instructions Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The

More information

2015 Feeney (8/15) # D. Aluminum Railing Systems

2015 Feeney (8/15) # D. Aluminum Railing Systems 2015 Feeney (8/15) #2012-425D Aluminum Railing Systems Aluminum Railing Systems Searching For a Complete Railing System? Look No Further. DesignRail by feeney aluminum railing frame systems combine the

More information

Clearview Railing System Installation Instructions

Clearview Railing System Installation Instructions Clearview Railing System Installation Instructions Disclaimer: AGS Stainless, Inc. has its Clearview Railing Systems designed by a professional engineer to meet the requirements of the latest national

More information

SECTION CHAIN LINK FENCING

SECTION CHAIN LINK FENCING SECTION 32 31 13 CHAIN LINK FENCING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The Work specified in this Section consists of furnishing and installing permanent chain link fences and gates in accordance

More information

2013 Feeney (2/14) # B. Aluminum Railing Systems

2013 Feeney (2/14) # B. Aluminum Railing Systems 2013 Feeney (2/14) #2012-425B Aluminum Railing Systems Aluminum Railing Systems Searching For a Complete Railing System? Look No Further. DesignRail by feeney aluminum railing frame systems combine the

More information

SIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL "A-1"

SIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL A-1 1 1/2" x 60" Galvanized (thread both ends) Top Bolt See Detail "A-1" and Slotted Channel Parallel Conduit Clamp Warning Sign 3 Equal Bolt Spacings (3 places at 12" min. spacing) (1) 3/8"x 7" min. (4"x

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

ANSI ORIFICE FLANGES METAL-KOREA

ANSI ORIFICE FLANGES METAL-KOREA METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding

More information

SECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION

SECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION SECTION R507 DECKS R507.1 Application. The provisions of this section shall provide prescriptive requirements for the design and construction of all uncovered, wood-framed, single-span exterior decks.

More information

STRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE:

STRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE: SECTION 05100 STRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE: A. The WORK of this SECTION shall consist of furnishing all the labor, materials, and equipment necessary for installation of structural

More information

ATLANTIS RAIL Contact Information

ATLANTIS RAIL Contact Information ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing

More information

Edgerail Aluminum Bridge Railing System Specification & Installation Instructions

Edgerail Aluminum Bridge Railing System Specification & Installation Instructions Edgerail System Specification & Installation Instructions Hill & Smith, Inc 1000 Buckeye Park Road Columbus, Ohio 43207 Tel: 614-340-6294 Fax: 614-340-6296 www.hillandsmith.com Section A System Specification

More information

Post & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS

Post & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM

More information

Open Up Your View With CABLE SYSTEMS

Open Up Your View With CABLE SYSTEMS Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching

More information

Series Sloped glazed Curtain wall. Installation Instructions

Series Sloped glazed Curtain wall. Installation Instructions Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End

More information

Design and Construction Standards SECTION ATHLETIC LOCKERS

Design and Construction Standards SECTION ATHLETIC LOCKERS SECTION 10505 ATHLETIC LOCKERS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,

More information

B. See Division 05 Section "Pipe and Tube Railings" for metal pipe and tube railings.

B. See Division 05 Section Pipe and Tube Railings for metal pipe and tube railings. SECTION 055000 - METAL FABRICATIONS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following, applicable: 1. Miscellaneous steel framing and supports. 2. Prefabricated building columns. 3. Shelf

More information

SECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

D. Thermally Sprayed Metallic Coating (Flame Spray): STD SPEC

D. Thermally Sprayed Metallic Coating (Flame Spray): STD SPEC STANDARD SPECIFICATION SECTION 05121 MISCELLANEOUS METALWORK PART 1 - GENERAL 1.01 DESCRIPTION This section includes materials, fabrication, and installation of structural steel, connecting bolts, pipes,

More information

GLOSSARY OF TERMS SECTION 8

GLOSSARY OF TERMS SECTION 8 GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the

More information

Salter Industries Spiral Stair

Salter Industries Spiral Stair Salter Industries Spiral Stair The Leader in Spiral Staircases Continuous Sleeve Stair Installation Instructions TOOLS NEEDED: 1. Electric drill with hex chuck and Phillips bit 2. Drill bits 1/8", 1/4",

More information

Installation Instructions

Installation Instructions Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF

More information

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation

More information

B-27-A BRIDGE RAILING, 3 TUBE WITH PICKETS SECTION THROUGH RAILING WITH BRUSH BLOCK SECTION THROUGH RAILING WITH SIDEWALK

B-27-A BRIDGE RAILING, 3 TUBE WITH PICKETS SECTION THROUGH RAILING WITH BRUSH BLOCK SECTION THROUGH RAILING WITH SIDEWALK 3" 1'- ƒ " 11 " 7 " TOP OF REAR FLANE TO BE ROUND 2'- LON PICKET 1'- W6 x 25 1 " THICK BASE PLATE " " ELASTOMERIC BOUND FABRIC PAD 8" SLAB DETAIL A (SEE 3) OVERHAN SECTION THROUH RAILIN WITH BRUSH BLOCK

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-05 52 00 (February 2018) ----------------------------- Preparing Activity: NASA Superseding UFGS-05 52 00 (August 2015) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

TREX ENHANCE RAILING (Also Applies to Trex Select Railing) Installation Instructions

TREX ENHANCE RAILING (Also Applies to Trex Select Railing) Installation Instructions TREX ENHANCE RAILING (Also Applies to Trex Select Railing) NOTE: All Enhance Railing lengths are manufactured at CLEAR SPAN dimensions (spanning between space of posts): 7" for 6' clear span. Note that

More information

UFGS (November 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS

UFGS (November 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCESA / NASA UFGS-05 52 00 (February 2011) Change 2-11/12 ----------------------------- Preparing Activity: NASA Superseding UFGS-05 52 00 (November 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS

More information

10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS

10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS 10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS 10x12 WOOD SKID FLOOR FLOOR SYSTEM FOR 10x12 TRICO AND FLORA SHEDS RAW MATERIALS LIST: 2 (9) FLOOR FRAMING AND SHEATHING: 1) BAND BOARD 2 x 6 x 12 PRESSURE

More information

The following instructions will guide you through the installation of your new vinyl railing.

The following instructions will guide you through the installation of your new vinyl railing. Installation Guide St. James Vinyl T-Rail Tools Required Protective eye glasses 3/8 x 3 Concrete Anchors/Fasteners (for Tape measure concrete installations) Variable speed drill/screwdriver Philips Driver

More information

Storefront Installation Guide

Storefront Installation Guide Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation

More information

MISCELLANEOUS SIGN CONNECTION DETAILS TYPICAL ROUTE MARKER ASSEMBLIES SIGN TO POST MICHIGAN DEPARTMENT OF TRANSPORTATION

MISCELLANEOUS SIGN CONNECTION DETAILS TYPICAL ROUTE MARKER ASSEMBLIES SIGN TO POST MICHIGAN DEPARTMENT OF TRANSPORTATION 5-4" SEE DETAIL I COUPLING BAR ON 3 2-10" CANTILEVER SIGN SUPPORT TYPICAL ROUTE MARKER ASSEMBLIES 5/1 DIAMETER STAINLESS STEEL BOLT AND NYLON INSERT LOCK NUT SELF-ALIGNING STEEL REINFORCING PLATE ( TYPE

More information

GENERAL ISOMETRIC LAYOUT

GENERAL ISOMETRIC LAYOUT EXISTING OR PROPOSED WIPER WALL SUPPORT STRUCTURE GATE LID CARBATHAN HG 0 WEB GRAY LOWER PAN GRATING ALUMINUM WIPER WALL CARBATHANE HG, 90 GRAY STRUCTURAL SPECIFICATIONS:. FLOODGATE MATERIAL TO BE ALUMINUM

More information

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details. SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.

More information

TREX SELECT RAILING. Installation Instructions PARTS

TREX SELECT RAILING. Installation Instructions PARTS RAILING NOTE : All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (76.8 cm) for 6' (.83 m) on center, and 9-5/8" (35.3 cm) for 8' (.44

More information

Installation manual. For setting in concrete/on base plates - Panel height 1830

Installation manual. For setting in concrete/on base plates - Panel height 1830 1 Aluminium fencing and drive-in gates Installation manual For setting in concrete/on base plates - Panel height 1830 Aluclos system components: U10 Connecting U-bracket 1900 mm CL18/CL18.XL Half-height

More information

HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY

HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY WITH OPTIONAL S.S. S PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION

More information

SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS

SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION THERAPEUTIC POOL ACCESSORIES

SECTION THERAPEUTIC POOL ACCESSORIES PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 13 17 23.11 THERAPEUTIC POOL ACCESSORIES SPEC WRITER NOTES: Delete between // // if not applicable to project. Also, delete any other item or paragraph not applicable

More information

E:\Wilmot\DGN\14018pp.dgn 3/11/2015 6:49:16 AM

E:\Wilmot\DGN\14018pp.dgn 3/11/2015 6:49:16 AM 600-06 SHOULDER WIDENING FOR TYPE (SPECIAL) GUARDRAIL TERMINALS E:\Wilmot\DGN\08pp.dgn //05 6:9:6 AM E:\DGN\08SUP.dgn //05 ::55 PM E:\DGN\08SUP.dgn //05 :8:0 PM E:\DGN\08-WRG.dgn //05 :8:5 PM E:\DGN\08SM.dgn

More information

SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).

SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM). PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3

More information

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL DHS-500 IMPACT SYSTEM INSTALLATION MANUAL TABLE OF CONTENTS SECTION PAGE GENERAL NOTES 3 EXTRUSION & PARTS IDENTIFICATION 4-5 DETERMINE FRAME SIZE 6 FABRICATE VERTICAL MULLIONS & FILLERS 7-8 FABRICATE

More information

SECTION 58 PRECAST CONCRETE BOX CULVERT. This work consists of furnishing and installing Pre-cast Concrete Box Culverts.

SECTION 58 PRECAST CONCRETE BOX CULVERT. This work consists of furnishing and installing Pre-cast Concrete Box Culverts. SECTION 58 PRECAST CONCRETE BOX CULVERT 58.1 DESCRIPTION A. General This work consists of furnishing and installing Pre-cast Concrete Box Culverts. B. Related Work Section 51 Section 52 Section 53 Section

More information

Create cable assemblies to fit your style

Create cable assemblies to fit your style 2015 Feeney (11/15) Quick-Connect Brochure #2015-975B Create cable assemblies to fit your style Quick-Connect Solutions Guide The fast and easy way to create your own CableRail assemblies! Our CableRail

More information

Chapter 17 - Porch Trim

Chapter 17 - Porch Trim Chapter 17 - Porch Trim Contents Chapter 17 - Porch Trim... 17-1 Timing & Prerequisites... 17-2 Trim on Porch Beams (Volunteer)... 17-4 Smart Trim on the Bottom of the Beam... 17-4 Smart Trim on the Inside

More information

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details. SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.

More information

One-sided rack, hot-dip galvanized Space between bicycles 350 mm length approx.kg Part-No. Two-sided rack, hot-dip galvanized

One-sided rack, hot-dip galvanized Space between bicycles 350 mm length approx.kg Part-No. Two-sided rack, hot-dip galvanized Bicycle rack Sturdy and space-saving due to alternating high and low racks. Racks can be bolted to form a serial system, with boreholes for anchoring or plugging. Bicycle parking rack Frame of angular

More information

Midwest Roadside Safety Facility

Midwest Roadside Safety Facility 19'-11 1/2" 6083 239'-11 1/2" 73139 Impact 1100C 25 43 5/16" 1100 upstream from the upstream face of the first shear fender downstream of the joint between barrier nos. 7 and 8 Upstream End Downstream

More information

Kwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Kwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com

More information

GENERAL ELEVATION SECTION A-A

GENERAL ELEVATION SECTION A-A NORTH OR WEST Final pavement Elev. m @ roadway 12 352 out to out precast backwall panels Final pavement Elev. m @ roadway SOUTH OR EAST Pile cut-f Elev. m Pile cut-f Elev. m 3:1 3:1 Approx. existing groundline

More information

Installation Instructions for. Handrail Component System

Installation Instructions for. Handrail Component System Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32

More information

BASEBALL FOUL POLES GROUND SLEEVE MOUNTED

BASEBALL FOUL POLES GROUND SLEEVE MOUNTED X X Page 1 of 6 GROUND SLEEVE INSTALLATION Ground Sleeve Foul Pole Size "A" F39901 32' and 40' 67 5/8" F39902 24' 67 5/8" F39903 16' 43 5/8" 00402000 12' 29 3/8" 7" ONE SET OF SLOTS MUST BE PARALLEL AND

More information

Midwest Roadside Safety Facility

Midwest Roadside Safety Facility B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized

More information

ATI Evaluation Service A Division of Architectural Testing Certification Services

ATI Evaluation Service A Division of Architectural Testing Certification Services ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 10/13/2016 Issued: 12/17/2014 Visit www.ati-es.com for current status Revised: 06/05/2015 Page 1 of

More information

TREX SELECT RAILING Installation Instructions

TREX SELECT RAILING Installation Instructions RAILING NOTE : All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (76.8 cm) for 6' (.83 m) on center, and 9-5/8" (35.3 cm) for 8' (.44

More information

TECHNICAL CORRECTION October Process Industry Practices Structural. PIP STF05121 Fabrication and Installation of Anchor Bolts

TECHNICAL CORRECTION October Process Industry Practices Structural. PIP STF05121 Fabrication and Installation of Anchor Bolts TECHNICAL CORRECTION October 2006 Process Industry Practices Structural PIP STF05121 Fabrication and Installation of Anchor Bolts PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize

More information

Lateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later

Lateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite

More information

ALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list.

ALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. ALUMINUM RAILING INSTALLATION INSTRUCTIONS AF#2010-308D Glass Infill Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 2) Gather and Identify

More information

DECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7.

DECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7. DECKS Max. riser height-7 ¾ Min. tread depth-10 Landings required at (R311.7.5.1) (R311.7.5.2) top and bottom of stairs (R311.7.6) Notched guardrail post NOT allowed Graspable handrail required Spacing

More information

SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section

SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section 02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,

More information

THE CASCADE & SLINGER FUNSLIDES

THE CASCADE & SLINGER FUNSLIDES THE CASCADE & SLINGER FUNSLIDES ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH CASCADE TM & SLINGER TM FUNSLIDES TM ARE MANUFACTURED FOR INSTALLATION AND USE ON RESIDENTIAL INGROUND

More information

New Product Release: October 2014 Boone Racks

New Product Release: October 2014 Boone Racks New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance

More information

BSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers

BSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers BSM, GSM & GSS Joint Kit Instruction (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers February, 1999 JOINT ASSEMBLY PARTS LIST Item Quantity Description

More information

Digitally Signed 06/02/2015

Digitally Signed 06/02/2015 Digitally Signed 06/0/05 Digitally Signed 06/0/05 Digitally Signed 06/0/05 FED. ROAD DIST. NO. STATE FED. AID PROJ. NO. SHEET NO. TOTAL SHEETS 6--5 6 ARK. JOB NO. 08057 6 8 075 QUANTITIES 5706 SUMMARY

More information

Now available at participating Feeney (2/14) AF# A. Stores. 1/8'' Stainless Steel Cable Assemblies to Enhance Any Railing and Any View!

Now available at participating Feeney (2/14) AF# A. Stores. 1/8'' Stainless Steel Cable Assemblies to Enhance Any Railing and Any View! 2014 Feeney (2/14) AF# 2009-236A Now available at participating Stores 1/8'' Stainless Steel Cable Assemblies to Enhance Any Railing and Any View! Easy-to-install, prefabricated cable assemblies are an

More information