Definition Assembly Instructions

Transcription

1 Definition Assembly Instructions Revision A-12 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service Kimball International, Inc. T F

2 Assembly Instructions Definition Set-on-Surface Bookcase Apply double-sided adhesive tape (Bottom) Pencil or Erasable Marker Scissors or Utility Knife Package Contents Double-sided Adhesive Tape Note: It is recommended that two (2) persons be used to lift and place the set-on surface bookcase. 1. To securely attach a set-on-surface bookcase to a worksurface, carefully turn the bookcase upside down on a smooth, hard surface. Cut two strips of double-sided (Top) adhesive tape and place them along the bottom panel as shown. DO NOT remove the film backer to expose the adhesive at this time. (). 2. Carefully turn the bookcase upright and place it on the worksurface in its desired position. Mark this location. Note: The worksurface MUST be clean, dry, and free of any dirt or residue to assure adequate adhesion. Lift the bookcase and remove the film backers from the double-sided adhesive tape. Adhere the bookcase to the marked location on the worksurface. (). Caution: The tape is a very strong adhesive and bonds instantly to any surface it is applied to. Peel off film backer Mark desired location Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-10

3 Definition Casegoods Assembly Instructions Task Station #2 Phillips Head Bit Tape Measure Screw Gun Level Hardware Required #10 x 1" Panhead #8 x 1 1 4" Panhead 3" 18" 1. Task stations are comprised of returns and corner units. Position the preassembled units in their desired location. (). 2. Level the units. Install the flat brackets to the corner unit using #10 x 1" panhead screws provided. (). 3. Align the end panels so the dowel aligns the upper edge. Dowel Pull the units together and attach the undersurface connecting rail using #8 x 1 1 4" panhead screws provided. Attach return worksurface to flat brackets already installed on the corner unit using #10 x 1" panhead screws provided. Re-level units. (). 4. Prior to installing the pedestals (ordered separately) remove the L-brackets attached to the end panel/worksurface to allow pedestals to fit flush against the end panel. (Figure D). Figure D Connection Rail Remove all L-brackets attached to end panels Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-05

4 Universal Assembly Instructions Pedestal Drawer Removal None Release Tab Package Contents None 1. Extend the box or file drawer to its full extension. Locate the drawer slide release tab, in the approximate location shown, on each side of the drawer box. Press tabs in and pull drawer straight out until slide drawer members disengage from cabinet members. (). Note: Lateral file drawer fronts use six (6) screws. 2. To reinstall drawer, extend slide cabinet members. Note: Make sure chrome ball bearing member is also forward. Carefully align slide drawer members with cabinet members and gently push drawer closed. Check for proper alignment by inspecting drawer front margins for spacing and squareness. Release Tab Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision B-10

5 Casegoods Assembly Instructions Definition Page 1 of 2 Wall Mounted Storage Hacksaw Level Traxx Wall Mount Bracket Package Contents Overhead Storage Overhead Brackets Spacer Blocks 1. The TRAXX wall mount bracket (ordered separately) allows you to hang an overhead cabinet off a building wall. (). 2. The wall mount bracket consists of one piece of extruded aluminum Traxx 72" long. The 72" bracket will have to be field-cut if a smaller single cabinet is to be used. Follow Traxx installation sheet to install Traxx to wall (overhead brackets hang from the Traxx wall mount bracket). (). Note: The optional overhead filler strip (ordered separately) is used to conceal the Traxx wall mount bracket. If the filler bracket is to be used, install the filler bracket prior to hanging the overhead cabinet. 3. To install the overhead cabinet filler bracket, loosen the outer-most screw on the end of the Traxx wall mount bracket. Slide the drilled flange of the filler bracket behind the Traxx wall mount bracket. Align the top of the filler bracket flush with the top of the wall mount bracket. Re-tighten the screw in the wall mount bracket. Use a level to align the filler bracket vertically. Fasten the lower portion of the filler bracket to the wall with the provided screw. (). Loosen Screw Slide drilled flange of filler bracket behind Traxx 72" Traxx Wall Mount Bracket Flush Align vertically Attach filler bracket to wall Part No Revision D-03

6 Definition Casegoods Assembly Instructions Page 2 of 2 (continued) 4. Position the overhead brackets on the Traxx wall mount brackets and align them with the mounting hardware already attached to the back of the overhead cabinet. 30", 36", 42", and 48" wide cabinets require two overhead brackets. 60", 66", and 72" wide cabinets require four overhead brackets. (Figure D). 5. Prior to hanging the cabinet, attach the spacer block(s) (using the double-face tape) to the back side of the cabinet to allow for proper spacing from the wall. 30", 36", and 42" cabinets require one spacer block. 48", 54", 60", 66", and 72" cabinets require two spacer blocks. (Figure E). 6. Install the overhead by tilting the bottom of the cabinet approximately 15 away from the wall, and engaging the bracket on the inside of the cabinet onto the overhead bracket on the Traxx. Tip: Cabinets with door(s) should have the door(s) open while hanging to aid in locating overhead bracket. Figure D Overhead Brackets Figure E Mounting Brackets Spacer Block Flush with bottom edge of the back Printed in U.S.A Kimball International, Inc. T F Part No Revision D-03

7 Casegoods Assembly Instructions Lock Core Lock core with pre-inserted key None Package Contents Lock Core/Key (key may be either rectangular or round head) 1. The key is pre-inserted into the lock core. Do not remove the key prior to lock core installation. (). 2. Prior to inserting the lock core/key be sure that the lock tenon on the end of the lock core is aligned with the cutout Lock Tenon at the back of the drawer/door lock housing. (). 3. To install the lock core, angle the core slightly so that the raised wafer () can be inserted into the lock Raised Wafer Lock Housing Drawer or Door Front housing. When the wafer is inside the housing, straighten the core and push in firmly to fully seat the core in the lock housing. (). 4. The lock core will only seat properly when the lock tenon and housing cutout are correctly aligned. You will not be able to remove the key if the core is not fully engaged and properly seated in the housing. (Figure D). Note: Future removal of lock cores require a yellow Change Key, ordered separately. Angle to insert Raised Wafer Lock Housing Straighten and push in Figure D Align Tenon and cutout prior to insertion Core not fully seated Core fully seated Printed in U.S.A Kimball International, Inc. T F Part No Revision A-04

8 Definition Executive Return Executive Bridge Casegoods Assembly Instructions 3" Tape Measure Screw Gun #2 Phillips Head Bit Level 18" Hardware Required #10 x 1" Panhead #8 x 1¹ ₄" Panhead Main Unit 1. Position the main unit in the desired location. Level main Align unit. Install the flat brackets to the main unit using #10 x 1" panhead screws provided. (). Return or Bridge 2. Align the return or bridge unit up to the main unit. Position the tops so the outer edge of the main unit and return unit are flush and pull tight against main unit. Fasten return top to the flat brackets using #10 x 1" panhead screws provided. (). 3. Align the main unit end panel and the return unit modesty panel to eliminate any crack between them. This can be done by adjusting the levelers up/down on the return or main units. Once the crack is eliminated, attach the main unit to the return unit using the return connecting rail and #8 x 1¹ ₄" panhead screws provided. Re-level units. (). Return Connecting Rail Main Unit Return or Bridge Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

9 Definition Operational Return Operational Bridge Tape Measure Screw Gun #2 Phillips Head Bit Level Casegoods Assembly Instructions Drop Bracket 3¹ ₂" Hardware Required #10 x 1" Panhead #8 x 1¹ ₄" Panhead 1. Position the main unit in the desired location. Level main unit. Install the drop bracket to the main unit using #10 x 1" panhead screws provided. (). 2. Align the return or bridge up to the main unit. Position the tops so the outer edge of the main unit and return unit are Main Unit Flush Return or Bridge flush. Align modesty panel of return to end panel of main unit. Fasten the return or bridge top to the drop bracket on the main unit using #10 x 1" panhead screws provided. (). 3. Align the main unit end panel and the return unit modesty panel to eliminate any crack between them. This can be done by adjusting the levelers up/down on the return or main units. Once the crack is eliminated, attach the main unit to the return unit using the return connecting rail and #8 x 1¹ ₄" panhead screws provided. Re-level units. (). Return Connecting Rail Main Unit Return or Bridge Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

10 Definition Assembly Instructions Component Returns Tape Measure Screw Gun #2 Phillips Head Bit Hardware Required Left Return Shown #8 x 1" Panhead #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket 1. A component return consists of a component worksurface, component pedestal(s), and a return modesty panel. These components are non-handed and can be configured as a left or right return unit. (). ⁵ ₆₄" 2. To install, place worksurface on a clean soft surface, underside facing up. The pedestal should be positioned ⁵³ ₆₄" Left Return Shown so the side is ⁵ ₆₄" from the edge of the worksurface. The pedestal should set ⁵³ ₆₄" from the back edge of the worksurface. (). 3. It is critical that the modesty panel extend ⁵ ₆₄" beyond the edge of the top in order to link to the main unit! Fasten pedestal metal rail and metal brackets to worksurface using #8 x 1" panhead screws. Fasten modesty to pedestal using #8 x ⁵ ₈" panhead screws. (). 4. Fasten modesty panel to worksurface through bracket using screws provided. (Figure D). 5. To assemble return to main unit see Executive Return, Executive Bridge Units instruction sheet. Figure D Worksurface Modesty ⁵ ₆₄" #8 x ⁵ ₈" Panhead #8 x 1" Flathead Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-10

11 Definition Assembly Instructions Breakfront Modesty (Kneewell) Tape Measure Screw Gun #2 Phillips Head Bit Square Breakfront Modesty Hardware Required #8 x 1" Panhead #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket 1. A breakfront modesty panel can be used between any two component pedestals to make a desk or credenza configuration. (). 2. Remove drawers from pedestals, then position pedestals upside-down on underside of worksurface. Attach the bracket to the pedestal at the desired position using #8 x ⁵ ₈" panhead screws. (Normal modesty position is 3" from the approach side of the desk). Attach modesty to brackets using #8 x ⁵ ₈" panhead screws. Position pedestal/modesty assembly to underside of top holding a margin of ⁵ ₆₄" on each side and 1¹ ₁₆" from the user edge to the pedestal wood rail. Fasten pedestal metal rail and metal brackets to worksurface using #8 x 1" panhead screws. (). Note: Make sure drawers are returned to their original location. To install, place worksurface on a clean soft surface, underside facing up. 3. Fasten modesty to worksurface using screws provided. (). ⁵ ₆₄" Pedestal Rails 1¹ ₁₆" #8 x ⁵ ₈" Panhead Worksurface #8 x 1" Flathead Modesty Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-10

12 Definition Assembly Instructions Ganging Kit #2 Phillips Head Bit Screw Gun Hardware Required #8 x ⁵ ₈" Panhead 1. The ganging bracket is used to connect two pedestals or two storage units together without defacing the exterior of the cabinets. (). 2. Pedestals can be ganged together using ganging brackets at either the top or bottom of the two units. If only one bracket is being used, it should be positioned at the bottom location. Use #8 x ⁵ ₈" panhead screws provided with ganging kit. (). 3. Wall mount overhead storage units can be ganged together using a ganging bracket under the two units. Use #8 x ⁵ ₈" panhead screws provided with ganging kit. (). Note: Use only with wall mount overhead storage units. Ganging Brackets Ganging Bracket Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-10

13 Definition Casegoods Assembly Instructions End Panel (T-Leg) Tape Measure Screw Gun #2 Phillips Head Bit Level End Panel Hardware Required Support Panel #8 x ⁵ ₈" Flathead #8 x 1" Flathead #8 x ⁵ ₈" Panhead Bracket 1. To assemble the T-leg end panel, attach the brackets to the end panel, then attach brackets to support panel using the #8 x ⁵ ₈" flathead screws provided. (). 2. To install the end panel, place worksurface on a clean, soft surface, underside facing up. The end panel should be located with a margin of ⁵ ₆₄" around the front, side, and back. (). 3. Secure end panel to worksurface through brackets using screws provided. (). ⁵ ₆₄" ⁵ ₆₄" Worksurface End Panel ⁵ ₆₄" #8 x ⁵ ₈" Panhead #8 x 1" Flathead Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

14 Casegoods Assembly Instructions Definition Page 1 of 2 Keyhole Top, U Top, and P Top Keyhole Top Tape Measure Screw Gun #2 Phillips Head Bit Level U Top P Top Hardware Required #8 x ⁵ ₈" Flathead #8 x 1" Flathead #8 x ⁵ ₈" Panhead Bracket 1. Keyhole tops, U tops or P tops can be configured either as work returns or as desking elements. These tops should never be used as freestanding furniture. (). 2. To assemble the T-leg end panel, attach the brackets to the end panels, then attach brackets to support panel using the #8 x ⁵ ₈" flathead screws provided. (). 3. To install the end panel, place worksurface on a clean, soft surface, underside facing up. The end panel should be located with a margin of ⁵ ₆₄" around the front, side, and back. (). End Panel Support Panel ⁵ ₆₄" ⁵ ₆₄" ⁵ ₆₄" Part No Revision D-04

15 Definition Casegoods Assembly Instructions Page 2 of 2 (continued) 4. Secure end panel to worksurface through bracket using screws provided. (Figure D). 5. For units with modesty panels, position end panel as shown in Figure E. The modesty panel can be positioned in the center of the half cylinder support base or moved flush with either end of the base. Attach the brackets to the end panel and half cylinder base using #8 x ⁵ ₈" panhead screws prior to attaching the modesty panel. Brackets must be mounted facing inside (toward the user's side) in the kneewell. Attach the modesty panel brackets on the end panel and support base using the #8 x ⁵ ₈" flathead screws. (Figure E). Note: If using optional center drawer, modesty panel will need to be flush with the front edge of the half cylinder base to allow clearance. Figure D Worksurface End Panel #8 x ⁵ ₈" Panhead #8 x 1" Flathead Figure E User side Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

16 Definition 1 Highback Organizer Corner Highback Organizer 1. The highback organizer sits on top of a worksurface. It can be attached to the worksurface using the double faced tape provided. 2. Attach double faced tape to the bottom of the highback organizer end panels. Position highback unit 5 64" from the back and side edges of the worksurface. Note: Double faced tape will create a strong bond. Make sure highback unit is positioned in desired location prior to final attachment. (). Assembly Instructions Revision F

17 Definition Casegoods Assembly Instructions Suspended Overhead Storage Drill ⁷ ₃₂" Drill Bit #2 Phillips Screwdriver Suspended Overhead Storage Set-on Storage 1. A suspended overhead storage unit mounts between two set-on storage units or between a set-on storage unit and a vertical storage unit. Align the units in their desired position. (). 2. If suspended overhead cabinet is used between two floor standing vertical storage units, you must position a pair of ¹ ₈" spacers (provided) between the suspended overhead and the freestanding unit. Peel off double faced tape and fasten to side panel of suspended storage unit. Attach foam to end panel ¹ ₈" from the front edge of end panel. (). 3. A suspended unit should not be connected to another suspended unit! (). Spacer Foam Strip Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

18 Universal Tackboards and/or Powered Tackboards Assembly Instructions Cable Routes Drill/Screw Gun Level #2 Phillips Head Bit Small Blade Screwdriver Hardware Required #8 x ⁵ ₈" Flathead 1. Tackboards can be attached to any highback organizer to provide a tackable surface. Tackboards can also be wall mounted. The tack panel is provided with routed channels on the back side to help manage cords. (). 2. Insert a screw into the hole of each loose Dual Lock pad, 4 or 6, as required. (). 3. Press pads with screw protruding against the pads which are already mounted to the back of the tackboard, locking the pads together. Position tackboard on mounting surface, making sure it is level. Apply pressure on board over pads to mark surface with screw points. (). 4. Carefully detach pads with small blade screwdriver and fasten in locations previously marked in step 3. Position tackboard against mounting surface, making sure it is level, and engage until each pair of pads snap together. 5. Wall Mount Caution: Pads should be located on wall studs, or secured to wall with anchors (not provided). Dual Lock Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-10

19 Definition Casegoods Assembly Instructions Set-on Storage Decorative Top Drill Screw Gun Tape Measure ³ ₁₆" Drill Bit #2 Phillips Head Bit 3" 3" Hardware Required #8 x 1¹ ₂" Panhead 3" 3" 1. Decorative tops can be added to the top of a storage unit. Longer tops can be used to span multiple storage units. All decorative tops are equipped with spacer rails and foam tape to create a ¹ ₈" reveal line between the storage unit and top. (). 2. Tops (30" to 72" wide) are shipped with two loose spacers. Longer tops (78" to 108" wide) are shipped with four loose spacers. These spacers can be positioned underneath the top to help support the weight of the top. Peel off the double stick tape and position as needed. Note: Spacer needs to be attached to top panel, not end panels. (). 3. To attach top to cabinets, measure inside of the cabinet 3" from sides. Bore thru the inside of top panel using ³ ₁₆" drill bit. Attach top using 1¹ ₂" panhead screws. (). 4. Butting two decorative tops will cause a gap between the storage units below of approximately ⁵ ₃₂". (). Foam tape is provided with each decorative top to help conceal this gap. Note: Foam tape is applied to side of one storage unit ¹ ₈" back from edge of end panel. ⁵ ₃₂" Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

20 Definition Casegoods Assembly Instructions Shelf Shelf None 1. Adjustable shelves can be added to any unit. An adjustable shelf consists of a shelf and four shelf support brackets. 12"D shelves use four shelf support brackets; 21"D shelves use six support brackets. (). 2. All cabinets feature pre-bored holes 1¹ ₄" apart. Recommended shelf spacing is #3 position for proper ring binder clearance. (). 3. For additional security, wood shelves can be fastened into position using #6 x ⁵ ₈" panhead screws (not provided). () Shelf Support Bracket Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

21 Definition Casegoods Assembly Instructions TRAXX Mounted Overhead None 1. Overhead cabinets can be hung from Traxx using the Traxx attachment bracket. (). 2. Insert the hook on top of the bracket into the Traxx at a 15 angle. (). 3. Pull downward on bracket allowing bracket to hang off the Traxx. Install the remaining brackets required to hang the overhead. 30", 36", 42" and 48" cabinets require two brackets. 60", 66", and 72" cabinets require 4 brackets. () Install the overhead by tilting the bottom of the cabinet approximately 15 away from the wall and engaging the cabinet bracket onto the Traxx attachment bracket located on the Traxx. (Figure D). 5. Let the cabinet rest against the spacer block or tiles. Repeat procedure for any additional overhead cabinets. 6. To level the cabinets, loosen the screws on the cabinet bracket and adjust accordingly. Tighten all screws after Traxx leveling. Figure D Cabinet Bracket Traxx Attachment Bracket Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

22 Definition Casegoods Assembly Instructions Modular End Panel #2 Phillips Head Bit Tape Measure Screw Gun Square Hardware Required End Panel #8 x ⁵ ₈" Panhead #10 x 1" Panhead #8 x 1" Flathead Bracket 1. The modular end panel is used to support the end of a worksurface when a pedestal is not used. End panels are 1" less in depth than worksurfaces to accommodate a modesty panel or filler strip. (). Modular End Panel Worksurface 2. Locate the end panel ⁵ ₆₄" from the front edge of the worksurface and ⁵ ₆₄" from the end of the worksurface. (). 3. Secure end panel to worksurface through bracket using screws provided. (). 4. Using a framing square, make sure end panel is perpendicular to the worksurface. Attach support panel bracket to modular end panel and underside of worksurface using #10 x 1" panhead screws provided. Note: Locate support panel bracket in the center of the worksurface. (Figure D). #8 x ⁵ ₈" Panhead Worksurface End Panel #8 x 1" Flathead Figure D ⁵ ₆₄" ⁵ ₆₄" Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

23 Definition Casegoods Assembly Instructions Support Panel #2 Phillips Head Bit Tape Measure Screw Gun Level Hardware Required #8 x ⁵ ₈" Panhead #8 x ⁵ ₈" Flathead #8 x 1" Flathead Bracket 1. An undersurface support panel is used to provide added support in the center of long worksurfaces where conventional support methods are not possible. These are required when kneespace area is 60" or more. (). 2. The bracket can be attached to either side of the support panel using a #8 x ⁵ ₈" panhead screw and is then attached to the underside of the worksurface using a #8 x 1" flathead screw. The bracket can be used on either side of the support panel to attach the support panel to a modesty panel. (). 3. If used with a modesty panel, the brackets are attached to the support panel with #8 x ⁵ ₈" panhead screws. The brackets are attached to the modesty panel with #8 x ⁵ ₈" flathead screws. Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

24 Definition Casegoods Assembly Instructions Tables Level ¹ ₂" Socket Socket Wrench Table Leg 1. Table legs are shipped with two hangar bolts already installed in the table leg. Align the two hangar bolts through the table corner bracket and attach with ¹ ₂" nuts and washers provided. (). Apron Rail Apron Rail Table Top Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

25 Definition Casegoods Assembly Instructions Modular Worksurfaces Tape Measure Screw Gun #2 Phillips Head Bit Level Hardware Required #10 x 1" Panhead 1. Modular worksurfaces can be used alone, or in combination with pedestals, modesty panels, end panels, or support panels to make any desired configuration. (). 2. Position the main unit in the desired location. Level main unit. Install the flat brackets to the main unit using #10 x 1" panhead screws provided. (). 3. Align the worksurface to the main unit. Position the tops so the outer edge of the main unit and return unit are flush and pull tight against main unit. Fasten return top to the flat brackets using #10 x 1" panhead screws provided. (). 3" 18" Main Unit Align Return or Bridge Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

26 Definition Assembly Instructions Pedestal Filler Strip Tape Measure Pedestal Filler 1. A pedestal filler strip is used at the rear of the pedestal when a back panel or modesty panel is not in use. (). 2. Peel double face tape and attach filler strip to back edge of pedestal end panel. Filler strip can be used on right or left side. Hold ⁵ ₆₄" from edge of filler strip to edge of end panel. (). Pedestal Filler Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-10

27 Definition Casegoods Assembly Instructions Vertical Storage Level Screw Gun Metric Hex 5 ⁷ ₃₂" Drill Bit 1. Vertical storage units are available with a wide variety of door/drawer configurations. (). 2. Multiple units can be attached together if desired. Align two units side by side. Using a ⁷ ₃₂" bit, bore through shelf hole from one cabinet into the other. Using the tapped sleeve connector, align and fasten to adjacent storage unit using M4 screw provided. (). Tapped Sleeve M4 Screw Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

28 Definition Casegoods Assembly Instructions Task Transaction Shelf #2 Phillips Head Bit Tape Measure Screw Gun Hardware Required #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket 1. The transaction shelf can be used with the task/reception station. The transaction shelf can be positioned on either the right or left hand side of the station. The shelf rests on top of the 43" high panels. (Not inset). (). 2. The transaction shelf is fastened to the task station using 10" 12" the brackets and #8 x ⁵ ₈" panhead screws provided. 12" The bracket mounts flush with the top edge of the 43" high panel. The front brackets mount 10" off the inside edge of the station. The back brackets should be spaced about every 12". Fasten in position. (). 3. Locate the transaction shelf on top of the 43" high end panels. There should be a ³ ₃₂" margin where the top overhangs the task/reception station. Fasten shelf to station using #8 x 1" flathead screws provided. (). ³ ₃₂" ³ ₃₂" Printed in U.S.A Kimball International, Inc. T F Part No Revision D-04

29 Definition Assembly Instructions Component Pedestal #2 Phillips Head Bit Tape Measure Screw Gun Square Hardware Required #8 x 1" Panhead 1. Typical pedestal location for desk, credenza and returns without modesty panels. ⁵ ₆₄" 1¹ ₁₆" Pedestal Rails Note: See component return installation sheet for pedestal location of returns with modesty panels. 2. Remove drawers from pedestals, then position pedestals upside-down on underside of worksurface. Note: Make sure drawers are returned to their original location. To install, place worksurface on a clean soft surface, underside facing up. 3. Attach pedestal to underside of top holding a margin of ⁵ ₆₄" on each side and 1¹ ₁₆" from the user edge to the pedestal. Fasten pedestal metal rail and metal brackets to worksurface using #8 x 1" panhead screws. (). Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-10

30 Definition Assembly Instructions Modesty Panel #2 Phillips Head Bit Tape Measure Screw Gun Square Hardware Required #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket ⁵ ₆₄" 1. Remove drawers from pedestals, then position pedestals upside-down on underside of worksurface. 1¹ ₁₆" Note: Make sure drawers are returned to their original location. To install, place worksurface on a clean soft surface, underside facing up. 2. Attach pedestals to the worksurface prior to installing modesty panel. Prior to attaching modesty panel to pedestal, locate panel ⁵ ₆₄" from the edge of the pedestal end panel. (). 3. To attach the modesty panel, using the #8 x ⁵ ₈" panhead screws, run screws through the pre-bored holes in the #8 ⁵ ₈" Panhead pedestal back rails into the modesty panel. 4. Fasten modesty in kneewell area to worksurface using screws provided. (). Worksurface Modesty #8 x 1" Flathead Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-10

31 Casegoods Assembly Instructions Definition Page 1 of 2 Visual Board Pencil Screw Gun Tape Measure Drill Bits Level Screw Bits Note: This instruction sheet describes the installation of the Visual Board on a wall with wooden studs. Alternate mounting surfaces may include metal studs and masonary block when the appropriate fasteners are used; fasterers are NOT supplied. The Visual Board must NOT be mounted ONLY to wall board or similar sheet material. 1. Place visual board against wall in the approximate desired location. Mark the height of the top edge of the visual board and set aside. Measure down 11¹ ₄" from this mark and mark a level line. (). 2. Locate the centers of three (3) wall studs (recommended) and transfer these locations to the wall hanger. (). 3. Bore three holes through wall hanger 2" above the bottom flat edge from the locations marked in Step 2. Countersink or counterbore each hole on surface shown so that attaching screws will be flush or below. (). Note: Hole sizes are dependent on the size of the fastener selected and are NOT supplied. Mark height of top of Visual Board 11¹ ₄" Mark level line for Wall Hanger Center line of stud Wall Hanger Center line of stud 2" Beveled edge Bore through and countersink or counterbore THIS side Part No Revision B-04

32 Definition Casegoods Assembly Instructions Page 2 of 2 (continued) Figure D 4. Attach wall hanger to wall aligning the flat edge with the level line marked in Step 1. Make sure that each screw makes full, solid contact with each stud. (Figure D). 5. Place visual board flush against the wall so that the hanger rail is above the wall hanger and the wall hanger is between the end panels of the visual board. Carefully lower visual board until hanger rail is firmly seated on wall hanger. (Figure E). Center line of stud Level line from Step 1 Screw not supplied Figure E Visual Board Hanger Rail Wall Hanger Printed in U.S.A Kimball International, Inc. T F Part No Revision B-04

33 Definition Casegoods Assembly Instructions Hinge Adjustment Phillips Screwdriver 1. Side Adjustment: Turn front screw clockwise to increase door overlay, counterclockwise to decrease overlay. (). 2. Depth Adjustment: Loosen back screw. Adjust door to desired position and tighten screw. (). 3. Height Adjustment: Loosen screw(s) on the mounting plate. Adjust door to position and tighten screws. (). 4. Door Removal and : To remove, pull release lever back. (Figure D). To re-install, place the hinge on the mounting plate and push the rear of the hinge with finger pressure. The snap sound confirms a secure attachment. Side Adjustment Depth Adjustment Height Adjustment Figure D Removal Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

34 Definition Assembly Instructions Leveling Level; check four positions 7 32" Nutdriver Level Note: All floor units MUST be leveled as described below for appearance and proper function of doors and drawers. 1. Desk, Credenza, Return, Lateral File, Drawer Storage: Remove all drawers as required for access to leveling glide adjustment holes. 7 32" Nut Driver Note: To remove drawers, refer to the Pedestal Drawer Removal Assembly Instruction sheet or the Lateral File Drawer Removal Assembly Instruction sheet. Turn the glides fully in (counterclockwise) prior to leveling. Level the unit from front to back by first extending the glides on the outside corners (turn clockwise), then level the unit from side to side. Check adjustments by placing the level in the four positions shown. Adjust inside glides if applicable, to help support the desk/credenza. (). Leveling Glides 2. Bookcase, Cabinet Storage: The lower shelf has holes which access the leveling glides. Turn the glides fully in (counterclockwise) prior to leveling. Level the unit from front to back by extending the glides (turn clockwise). Level the unit from side to side. Check adjustments by placing the level in the four positions shown. (). Level; check four positions 7 32" Nut Driver Leveling glide adjustment hole Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-10

35 Definition Casegoods Assembly Instructions Leg Placement Racetrack Top Kidney Bean Top Rectangle Top Extended Top Crescent Top Round Top D Top U Top Arc Top P Top Tape Measure Screw Gun #2 Phillips Head Bit Square Hardware Required #10 x 1" Panhead 36" 1. Component worksurfaces may be supported using many different types of table legs. As a general rule, the center of the leg is located 4" from the edge of a flat rim, and 5" from the edge of a knife edge. 2. Place the worksurface on a clean, soft surface, underside facing up. Mark the leg locations on the underside of the top. Attach table legs using #10 x 1" panhead screws provided. Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

36 Universal Products Casegoods Assembly Instructions Support Bases #2 Phillips Head Bit Tape Measure Screw Gun 12" D 6" D 12" D Hardware Required #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket 1. Support bases are used to provide support for any worksurface shape. (). 2. To install, place worksurface on a clean, soft surface, underside facing up. Mark the center of the radius where the base attaches. Attach base to worksurface using #8 x 1" flathead screws and the #8 x ⁵ ₈" panhead screws provided. (). #8 x 1" Flathead Screw Printed in U.S.A Kimball International, Inc. T F Part No Revision E-04

37 Universal Products Assembly Instructions Lateral File Drawer Removal Anti-tip Mechanism None 1. All lateral file units have been equipped with an anti-tip mechanism. This mechanism is attached to the rear of the drawer slide cabinet member and only allows one drawer to be opened at a time. 2. To remove the drawers, unlock the unit, and extend the TOP DRAWER forward. (). 3. Press the two quick disconnect release tabs and lift the drawer off the slide assembly. (). Note: Shipping screws must be removed from drawer suspensions before drawer can be removed. 4. No other drawers can be removed without rotating the anti-tip mechanism catch UPWARD on each side of the cabinet. Remove the next drawer and repeat procedure. (). 5. To replace drawers, begin at the bottom. MAKE SURE CATCH is rotated DOWNWARD before inserting each drawer. (). Printed in U.S.A Kimball International, Inc. T F Part No Revision C-04

38 Definition Assembly Instructions Page 1 of 2 108" Highback Organizer Attach double-sided tape to each outer end panel Phillips Screwdriver Tape Measure or Ruler or Allen Wrench Scissors or Utility Knife Package Contents Double-sided Adhesive Connecting Bolts Tape Note: The 108" Highback Organizer is shipped as two pieces: a right and a left. Note: It is recommended that more than one person be used to assemble and install this unit. 1. Lay both organizer halves on their backs. Cut a piece of double-sided adhesive tape for each outer end panel. Peel off one side of the protective backing and attach the tape to the underside of each end panel. (). 2. Lift the first highback half into its desired location on the worksurface. Lift the second highback half into position against the first unit. Make sure units align and are flush on all sides. (). Caution: Make sure first unit is held steady while locating second unit. 3. Align connecting holes in highbacks and attach highbacks together using the six (6) provided connecting bolts. Insert half of a connector bolt into one connecting hole, and insert the other half into the opposite connecting hole. Tighten all bolts securely, making sure both highback halves are flush against each other with no gaps. (). Attach units using six connector bolts Align If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision B-10

39 Definition Assembly Instructions Page 2 of 2 (continued) Figure D 4. Make sure assembled unit is in its final desired position. Carefully tilt unit forward and remove remaining protective backing from each piece of double-sided adhesive tape. (Figure D). 5. Set unit upright and press down to ensure good bond with adhesive. (Figure E). Caution: Double-sided tape has a powerful adhesive which permanently bonds to any surface. Peel protective backing from double-sided adhesive tape Figure E Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision B-10

40 Definition Wall Mounted Overhead Bracket Tape Measure Variable Speed Drill Level with Torque Option (4 feet or greater) Drill Bits Metal Saw Screw Bits Package Contents Traxx (72" section) Assembly Instructions Page 1 of 2 4. Prepare wall for Traxx attachment by pre-drilling for and/or installing fasteners along the line drawn in Step 1 per the fastener manufacturer s guidelines. Recommended spacing of fasteners is 16", but should not exceed 24" on center. A single section of Traxx must attach to the wall with a minimum of two solid anchor attachment points. DO NOT extend the Traxx more than 6" beyond the last anchor attachment. (). Note: It is the responsibility of the installer and/or the contractor to select and install the proper fasteners in the structural wall. Kimball International does not furnish fasteners or assume liability for their use. Note: Kimball International defines a structural wall as a load-bearing wall constructed of materials such as: poured concrete, concrete block, or studs.wood studs must be a nominal 2" x 4" size minimum. Metal studs must be C channel, 20-gauge thick minimum. Metal or wood studs must be on centers no greater than 24" and have maximum height of 14' restrained at floor and ceiling. Interior walls shall be designed to resist not less than a force of 5 lbs. per square foot applied perpendicular to wall. The deflection of such wall under a load of 5 lbs. per square foot shall not exceed of the span for walls with brittle finishes, and of the span for walls with flexible finishes (per Uniform Building Code Section 2309b). If you have any questions concerning your load-bearing structures, please consult your architect or structural engineer. 1. Mark the Traxx center line position on the wall " from the floor for the length where the overhead is to be located. (). Check several positions along the line to ensure that the dimension is not less than ". 2. The 72" Traxx bracket will have to be field-cut if a smaller single cabinet is to be used. The Traxx length should be equal to the width of the overhead cabinet(s). 3. Locate the wall substructure along the line drawn in Step 1. For proper attachment of Traxx to the wall, fasteners must tie directly into the substructure of the wall (studs, blocks, solid masonry). Center line of Traxx 6" maximum beyond last anchor point If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision B-10

41 Definition 5. Position the Traxx against the wall just below the line drawn in Step 1. (). Transfer the fastener locations from the wall to the center line in the Traxx. 6. Drill the appropriate diameter hole in the Traxx per the fastener manufacturer s guidelines. Note: Hole sizes are dependent on the size of the fastener selected. Assembly Instructions Page 2 of 2 9. To install the overhead cabinet filler bracket, loosen the outer-most screw on the end of the Traxx wall mount bracket. Slide the drilled flange of the filler bracket behind the Traxx wall mount bracket. Align the top of the filler bracket flush with the top of the wall mount bracket. Re-tighten the screw in the wall mount bracket. Use a level to align the filler bracket vertically. Fasten the lower portion of the filler bracket to the wall with the provided screw. (Figure D). Recommended Fastener Size Model No. Steel Stud (for 1 2 " to 3 4" drywall): Hilti Toggler anchor toggle bolt Wood Stud (for 1 4" to 1 2" drywall; meets or exceeds ANSI/ASME B and SAE J933): Panhead sheet metal screw 1 4"-20 x 2" Grade 5 or equivalent 10-2 PHPMS Wall Transfer locations of fasteners to center line of Traxx Solid Masonry: Crown Bolt lag shields 1 4" x 1 1 2" Buildex Tapcon concrete 1 4" x 2 3 4" anchor screw Masonry Block: Hilti Toggler anchor toggle bolt 1 4"-20 x 2" Grade 5 or equivalent Crown Bolt lag shields 1 4" x 1 1 2" Buildex Tapcon concrete 1 4" x 2 3 4" anchor screw 7. Before installing the Traxx, touch-up any exposed cut ends. 8. Attach Traxx to wall aligning the center line of Traxx to line drawn in Step 1. Ensure that each fastener is securely attached to wall substructure. Note: The optional overhead filler strip (ordered separately) is used to conceal the Traxx wall mount bracket. If the filler bracket is to be used, install the filler bracket prior to hanging the overhead cabinet. Figure D Lossen Screw Slide long flange of filler bracket behind Traxx Flush Align vertically Attach filler bracket to wall Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision B-10

42 Definition Casegoods Assembly Instructions Vertical Storage/Bookcases Level Metric Hex 5 Screw Gun 7 32" Drill Bit Package Contents M4 screw Tapped Sleeve Connector 1. Vertical Storage Units, Freestanding and Set-on Bookcases can be attached together if desired. (). 2. Align two units side by side. Using a 7 32" drill bit, bore through shelf hole from one cabinet into the other. Using the tapped sleeve connector, align and fasten to adjacent storage unit using M4 screw provided. (). Vertical Freestanding Set-on-surface Storage Bookcase Bookcase M4 Screw Tapped Sleeve Connector Connecting Bolts Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision E-06

43 Definition & Priority Casegoods Assembly Instructions Slat Wall Tile Drill/Screw Gun Phillips Screwdriver #2 Bit, Level Hardened Package Contents (14) #8 x 5 8" Panhead Screws (3) Mounting Brackets 1. Slat tile may be attached to inside face of back panel on Highback Organizer using supplied mounting brackets and screws. (). 2. Attach three mounting brackets (beveled edge up) at recommended height of 14" from bottom edge of back panel to bottom edge of mounting brackets and spaced horizontally to match mating brackets on back of slat tile. Brackets to be positioned level and attached using supplied #8 x 5 8" long screws (four screws per bracket). (). 3. Place slat tile against back panel and above secured mounting brackets. Lower slat tile onto mating mounting brackets until fully engaged. 14" 4. Using #8 x 5 8" screws, secure bottom corners of slat tile by inserting one screw in each pre-bored hole located in lower corners. (). #8 x 5 8" screw Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision A-07

44 Assembly Instructions Definition 1 Modesty Panel with Wing Tape Measure Cordless Drill #2 Philips Head Bit Square Hardware Required #8 x 5/8 Panhead Flakeboard Screws #8 x 1 Flathead Flakeboard Screws L brackets Tape measure 1. Prep modesty panels by attaching L brackets with long leg of bracket attached to modesty with 5/8 screws (Figure A). 2. Mount the modesty wing panel to the end panel () or the side of a storage unit () so that it is flush with end panel or set back no more that 2 from edge of worksurface*. Attach to end panel with 5/8 screw and to worksurface with 1 screw (Figure D). Use square to insure panel is perpendicular to end and worksurface. 3. When attaching modesty panel insure that it is parallel with the front of the worksurface by measuring its inset at both ends. (Figure E). Attach with 1 screws to worksurface and 5/8 screws to end panels. Note: *Verify modesty location with application of support and its location. Figure D Flush with End To 2 set back from worksurface Flush with End To 2 set back from worksurface Worksurface End Panel Viewed from underside Figure E Worksurface Modesty Panel Modesty Panel Viewed from bottom of assembly , Revision -

45 Assembly Instructions Definition 1 Technology Modesty Panel Tape Measure Cordless Drill #2 Philips Head Bit Hardware Required L Brackets #8 x 5/8 Panhead Screws #8 x 1 Panhead Screws #8 x 1 3/4 Panhead Screws 1. Install L brackets to end panels with #8 x 1 panhead screw, long leg to panel (). 2. Align end panel flush with the bottom of panel it attaches too. On a storage unit the panel needs to be even with the back of the storage end panel to inset (). Check that both sides are the same distance off the back of the worksurface. Attach with #8 x 1 3/4 screws. 3. Flush bottom of modesty panel with bottom of end panels. Center in knee space opening (). There is side to side adjustment to meet multiple applications. 4. Attach modesty to L brackets attached to end panels with #8 x 5/8 (Figure D). Note: to insure proper function modesty must be installed perpendicular to the panels that make up the knee space its installed in. If not properly installed hinged panel could rub sides of knee space. Figure D Flush to Inset Center in opening Shown with worksurface and panels removed fore clarity , Revision -

46 Assembly Instructions Definition 1 Extension Surfaces and Support Tape Measure Cordless Drill #2 Philips Head Bit Hardware Required Flat Bracket #10 x 1 Panhead Screws #8 x 3/4 Panhead Screws L Brackets #8 x 1 Panhead Screws 1. Install flat brackets to worksurface that the extinction will run off of. Place brackets so that the set in 3 on each side based off the width of extension worksurface (). 2. Place extension worksurface on a clean soft surface, underside facing up. Note: Support should be positioned so that maximum unsupported span never exceeds 60. Pedestal attachment 3. Remove drawers from pedestal and place pedestal upside down on surface. Pedestal can be mounted at the end of the worksurface () or set in for an overhanging worksurface (). Note: Pedestals that are shallower than the worksurface are still located the same distance off the user side of worksurface. Metal leg attachment (O, U, and Elite) 4. Metal leg can be mounted at the end of the worksurface (Figure D) or set in for an overhanging worksurface (Figure E). 1 5/32 1 5/32 Figure D 18 Max 5/ Center front to back, flush with end , Revision -

47 Definition 2 Extension Surfaces and Support Metal leg attachment (O, U, and Elite) continued. 5. Use #8 x 1 panhead screws provided to attach leg to worksurface. Support panel attachment. 6. Support panel can be mounted flush or set in for an overhang worksurface (Figure F). Attach L brackets with screws provided. Panel should be centered front to back under worksurface for equal overhang. Attaching extension worksurface 7. Flip extension worksurface over, recommended that two people do this, and place on flat brackets (Figure G). 8. Attach with screws provided. Note: Support should be positioned so that maximum unsupported span never exceeds 60. Figure F Assembly Instructions Figure E 18 Max Figure G 18 Max Center front to back , Revision -

48 Definition 3 Extension Surfaces and Support Figure I Assembly Instructions Angled Extension Worksurface with metal leg or end panel support. 9. When installing support on angled worksurfaces perpendicular to the front edge, the support should line up with the end of the straight section of the worksurface on the approach side (Figure H). 10. Support mounted parallel to the end of the worksurface should be centered front to back and flush to inset 18 max (Figure I). Note: Support should be positioned so that maximum unsupported span never exceeds 60. Both locations shown. 18 Max Figure H , Revision -