Drill Press Storage Cart
|
|
- Amberly Osborne
- 5 years ago
- Views:
Transcription
1 Drill Press Storage Cart Richard Hicks on July 22, 2013 Drill Press Storage Cart
2 Drill Press Storage Cart My Inspiration ShopNotes Issue 128 Changes Used casters instead of wheels Didn t build the drill press mobile base Modified the dimensions to fit my needs and drill press Added anti-tip safety device Richard Hicks on July 22, 2013
3 Step One Establish the dimensions: Your drill press Post diameter Table height in normal use Base dimensions Storage needs (largest and smallest items to be stored) Parts that you will use to build the cart Casters Drawer slides
4 20 column to edge of table 32 from floor to tips of the handles
5 4 Column diameter 4 ½ collar diameter at 4 from floor 4 high Base is 13 wide
6 3 inch Caster Dimensions 4 high Mount is 2 ½ wide Source: Harbor Freight Cost $3.99 per caster Mount is 3 ½ long
7 18 Drawer Slide Dimensions Full Suspension drawer slide, 100# capacity 17 ½ long and 1 ¾ wide Source: Cost: $5.90 per pair (quantity 10 price)
8 Drill Press Storage Cart Richard Hicks on July 22, 2013 Banding the Plywood edges I like using plywood, but I don t like the plywood edges. I applied pre-glued, heat activated, edge banding on all of the exposed edges before assembly. I use an old iron (on dry, cotton heat setting) to heat the edge banding adhesive and a round shank Phillips screwdriver to press the adhesive strips in place. Banding adds about 1/64 to the size of the piece. Source: - $22.05 for 7/8 x 250 feet
9 Drill Press Storage Cart Richard Hicks on July 22, 2013 Banding the Plywood edges I used a FastCap Macro Flush Cutting Trimmer to trim the ends of the banding at the corners. Source: - $12.66
10 Drill Press Storage Cart Richard Hicks on July 22, 2013 Banding the Plywood edges I used a FastCap Quad Pro Trimmer to trim the edges of the banding. Even though it s made to trim both sides at once, I found it worked better to trim each side separately. I used a sanding block with 400 grit paper to sand the edges after using the trimmer. Source: - $20.35
11 Drill Press Storage Cart Richard Hicks on July 22, 2013 Cut List for the Cabinet * Note: Measure your plywood measurements are based on full ¾ thick Plywood
12 Drill Press Storage Cart Richard Hicks on July 22, 2013 Cut List for the Drawers * Note: Measure your plywood measurements are based on full ¾ thick Plywood
13 Plywood Layout Sheet
14 ¾ Plywood Sheet One 77 1/8 8 C - Side 23 ¾ x 19 D - Side 23 ¾ x ¾ x 9 1/4 F Cubby Back 23 ¾ x 9 1/4 G Cubby Back 23 ¾ x 10 H Cubby Side 23 ¾ x 10 I Cubby Side 23 ¾ X 18 4 DF-5 25 x 7 E - Back DF-4 25 x 4 ½ 23 ¾ 23 ¾ x 26 1/2 DF-4 25 x 4 ½ J Caster Support 29 x 5 X 15 DF-2 25 x 3 ½ DF-1 25 x 3 ½ K Caster Support 29 x 5 26 ½ /4
15 D3-A 16 1/2 x 3 ¾ Plywood Sheet Two 8 A - Base 26 ½ x 29 A - Top 26 ½ x /2 X 38 4 D3-A 16 1/2 x 4 D5-A 16 1/2 x 6 1/2 D3-B 24 x 4 D5-B 24 x 6 1/2 D3-A 16 1/2 x 4 D3-B 24 x 4 D3-A 16 1/2 x 3 D5-A 16 1/2 x 6 1/2 D2-B 24 x 3 D5-B 24 x 6 1/2 L Shelf D3-A 16 1/2 x 3 D3-A 16 1/2 x 3 D4-A 16 1/2 x 4 D2-B 24 x 3 D1-B 24 x 3 D4-B 24 x 4 10 x 8 ½ M Shelf D3-A 16 1/2 x 3 D4-A 16 1/2 x 4 D1-B 24 x 3 D4-B 24 x 4 10 x 8 ½ 16 ½ 16 1/
16 ¼ Plywood Sheet One 83 Drawer Bottom 1 23 ¼ x 17 ½ Drawer Bottom 2 23 ¼ x 17 ½ Drawer Bottom 3 23 ¼ x 17 ½ Drawer Bottom 4 23 ¼ x 17 ½ Drawer Bottom 5 23 ¼ x 17 ½ 23 ¼ x 7 24 ½ x 96
17 Edge Banding Edge Banding Edge Banding 5 radius Edge Banding A & B - (Top and Bottom) 26½ W x 29 L Edge Banding
18 Edge Banding Edge Banding Pocket Holes Pocket Holes C & D - (Right & Left Sides) 19L x 23¾ H Decide the size drawers you need (I used (2) 3½, (2) 4½ and (1) 7 drawer). Draw the slide mounting guide lines on both side panel (C) and (D).
19 Edge Banding Edge Banding Pocket Holes E - (Back) 26½ L x 23¾ H
20 Edge Banding Edge Banding Shelf Pin Holes Shelf Pin Holes E - (Back reverse side) 26½ L x 23¾ H Note: Match shelf pin hole spacing to parts H & I (Cubby Sides)
21 Edge Banding Edge Banding Pocket Holes Pocket Holes F & G (Cubby Back L & R) 9¼ L x 23¾ H
22 Edge Banding Edge Banding Pocket Holes Pocket Holes Shelf Pin Holes Shelf Pin Holes H & I (Cubby Side L & R) 10 L x 23¾ H Note: Match shelf pin hole spacing to part E (Back)
23 Edge Banding Edge Banding J & K Caster Support (L & R) 5 W x 29 L
24 Edge Banding Edge Banding L & M Cubby Shelves 8 ½ W x 10 L Edge band all four sides
25 Six Alignment Blocks 5 x 5 with ¾ dados Optional
26 The leftover plywood
27 Vacuum attachment on Kreg K-3 Jig
28 Installing left side (D) Clamp the side in position, drive three screws, remove the screws, add glue, re-clamp and re-screw.
29 Installing right side (C) Clamp the side in position, drive three screws, remove the screws, add glue, re-clamp and re-screw.
30 Installing the back (E) Clamp the back in position, drive three screws, remove the screws, add glue, re-clamp and re-screw. Screw the sides (C) and (D) to the back (E). The alignment blocks will help keep the pieces in place while you screw them together.
31 Installing the left cubby back (F) Clamp the Cubby back (F) in position, drive two screws on the bottom and two screws on the side, remove the screws, add glue, re-clamp and re-screw.
32 Installing the right cubby back (G) Clamp the Cubby back (G) in position, drive two screws on the bottom and two screws on the side, remove the screws, add glue, re-clamp and re-screw.
33 Installing the cubby sides (H) & (I) Clamp the Cubby side (H) in position, drive two screws on the bottom and two screws on the side, remove the screws, add glue, re-clamp and re-screw. Repeat for cubby side (I).
34 Install the drawer slides on both sides (C) and (D).
35 Installing the bottom (B) Turn cabinet upside down and install the bottom (B) panel. I used glue and secured the panel with brads. Next, add the caster supports (J) & (K) along each side of the cabinet.
36 My drawer sizes are: Building the Drawers (2) 24 x 18 x 3, (2) 24 x 18 x 4 and (1) 24 x 18 x 6 ½ The drawer fronts are: (2) 3½ x 25. (2) 4½ x 25 and 7 x 25 I used simple braded and glued butt joints, but reinforced the joints with dowels. * Note: Measure your plywood measurements are based on full ¾ thick Plywood
37 Building the Drawers After the glue dried, I drilled holes and glued ¼ dowels in the corner of each drawer.
38 Installing the Drawers After the drawers dry, install the other part of the drawer slides and install the drawers.
39 Installing the Drawers Install the drawer handles on the drawer fronts and then attach the fronts to the drawers. I used quarter spacing between the drawers (used a quarter as a measuring spacer between the drawer fronts).
40 Installing the Drawers The completed drawer installation.
41 Installing the Drawers After all the fronts are installed, remove the drawers one at a time and install the bottoms. I used ¼ melamine coated MDF and secured the bottom panel with brads. Reinstall the drawers.
42 Installing the casters Install the casters (the swivel casters go in front) and secure with 1 ½ screws and washers. Position the front casters so they don t protrude out from the front of the cabinet (eliminates a possible tripping hazard).
43 Installing the anti-tip safety feature As a safety measure, I installed an anti-tip brace across the top of the back of the cabinet. That s in case more than 1 heavy drawer gets opened at the same time. I used T-nuts through the top panel and knobs with 5/16 x 16 threaded studs.
44 The Completed Storage Cart
How to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationIndustrial Cart. Materials. With High Style Restyle
1 Industrial Cart With High Style Restyle Materials 1 sheet 3/4" plywood 1-1" x 2" x 8' board 2-1" x 3" x 8' board 1-2" x 8" x 10' board 1-2" x 6" x 8' board 3-1/4" x 2 1/2" x 4' poplar hobby boards, or
More informationBUTCHER BLOCK MICROWAVE OVEN STAND
BUTCHER BLOCK MICROWAVE OVEN STAND 828 The butcher block has fallen out of favor in recent years, replaced by the countertop cutting board in an attempt to save space. This design, however, makes the butcher
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationDewalt Organizer Storage Cabinet Plans
Dewalt Organizer Storage Cabinet Plans Version 1.0 How to build a system to perfectly organize you Dewalt storage organizers. With easy to follow step-by-step instructions, you will be able to cut, assemble,
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationmake something original Mobile Workstand Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2)
Mobile Workstand Panel (2) Leg (4) Long frame member (2) Crossmember (6) Shelf (1) Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2) THIS IS NOT THE COMPLETE PLAN: it is merely
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationMITER SAW SUPPORT WINGS PLAN
MITER SAW SUPPORT WINGS PLAN Version 1.0 How to build support wings for your miter saw With easy to follow step-by-step instructions, you will be able to cut, assemble, and finish your very own support
More informationPULLOUT SHELF ROCKLER BUILD IT WITH BUILD CUSTOMIZE
BUILD Stock Item 12229 Drawer s, 2 1 2" x 48" 63420 Baltic Birch Ply, 1/4" x 24" x 30" 38742 Maple, 3/4" x 3" x 24" 45953 100# Zinc Over-Travel Drawer Slides - Centerline 757-20" 30254 #8 x 1 1 4" Square
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationProject 13586EZ: Writing Desk. Writing Desk Materials List
Project 13586EZ: Writing Desk This writing desk will make a handsome addition to just about any room in the house. The one shown is made of cherry, a logical choice for a piece like this, but mahogany
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationEmpire Dresser Plans
1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More information(1) 2x4 Ft. Sheet of ¼-inch Plywood. 1 ¼-inch Wood Screws. 1 ¼-inch Brad Nails ¾-inch Brad Nails Wood Glue CUT LIST:
MATERIALS: (5) 1x3x8 Ft. Boards (3) 2x4x8 Ft. Boards (10) 1x4x8 Ft. Boards (1) 1x2x10 Ft. Board (1) 2x2x4 Ft. Board (2) 1x6x8 Ft. Boards (1) 4x8 Ft. Sheet of ¾-inch Plywood (1) 2x4 Ft. Sheet of ¼-inch
More informationBenchmark Media Console [1]
[1] Submitted by Ana White [2] on Fri, 2011-10-07 13:31 [1] Here she is!!!! Excited to post this plan for you, enjoy the plans! Happy Buiding, Ana Summary: Make your own Pottery Barn inspired Benchwright
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationDresser. Materials & Tools FEATURING FORMALDEHYDE-FREE TECHNOLOGY. Free Plans to build a Dresser
Free Plans to build a Dresser Materials & Tools Materials: 1-1/4 pocket hole screws 1-1/4 brad nails 3 sets of 18 drawer slides Drawer pulls Edge banding, optional Wood glue Sandpaper (100, 150, 220 grits)
More informationComputer Desk. Project designed by April Wilkerson
Project designed by April Wilkerson Copyright WilkerDos.com 2018 Project plan Desk Page 2 of 16 Page 3 of 16 File cabinet Page 4 of 16 Metal base Page 5 of 16 Glue up Get started by gluing up boards for
More informationBathroom Storage Unit. Wilkerdos.com
Bathroom Storage Unit Wilkerdos.com Copyright 2015 Material List Quantity Item Notes 1 4 x 8 x 3/4 plywood Construction grade 1 2 x 4 x 1/2 plywood Construction grade 11" 7-1/2" Page 1 Some 1 1/4" brad
More informationantebellum home in Eutaw, Alabama, built in 1860 (Google it for photos).
You Can Build the Kirkwood Bookcase By Jeff Branch A vid readers will tell you they often need a new way to store all of their books. I ve seen some pretty creative ways to stockpile books - in some instances
More information10 Easy-to-Build. Plywood Projects
10 Easy-to-Build Plywood Projects Ten shop projects ten sheets of plywood. These rock-solid essentials take just a couple hours to build and will help you make the most of the space in your shop. All content
More information786 Kurka Jig Owners Manual
7 Kurka Jig Owners Manual Please Read Carefully! 7 Parts List Parts listed in this box are shown in photos in the instructions. Part Description Quantity 7B Jig Plate Set, pieces..................... Six
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationShoe Organizer Plans Our Home from Scratch
Shoe Organizer Plans by Our Home from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, injury or death
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationChapter 22 - Cabinets & Vanities
Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...
More informationEasy Jewelry Box. Easy Jewelry Box 1
This easy to build dresser style jewelry box is designed to use standard board sizes you may already have on hand. Drawers are lined in felt and have felt covered bottoms to glide smoothly on the shelves
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationMaster Closet System. Master Closet System Published on Ana White (http://ana-white.com) posted by Ana White [1]
posted by Ana White [1] An entire closet system, for under $250 dollars. Page 1 of 21 Page 2 of 21 Additional Photos Page 3 of 21 Page 4 of 21 Page 5 of 21 Page 6 of 21 Page 7 of 21 Page 8 of 21 About
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationTools: Drill/Driver Kreg Jig Miter Saw Jigsaw Circular Saw Adjustable Square Tape Measure Veneer Trimmer Sandpaper and Sander
R PROJECT PLANS DROP-FRONT DESK Create a workspace almost anywhere with this drop-front desk. Mounted to a wall, it doesn t take up any floor space, which means you can hang it wherever you need to work.
More informationYou Can Build an Architectural Bookcase
Jeff Branch WOODWORKING You Can Build an Architectural Bookcase Heavy moldings bring this project to life. By JEFF BRANCH I am drawn to architecture. In particular, I like the orderly nature of Palladian
More informationCastle Bed. Page 1 of 24
Castle Bed www.andrewharriswoodwork.com Page 1 of 24 Introduction This plan makes a twin bed that is 91 inches long and 60 inches wide. I have tried to ensure all steps are covered in these plans but if
More informationindicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
p i r at e ' s c he s t t oy box What You'll Need lumber 1-1x2x4 1-1x2x8 1-1x3x2 2-1x3x8 1-1x6x4 1-3/4 x 2 x 4 sheet of plywood 1-3/8 or 11/32 x 4 x 8 sheet of beadboard paneling 1-9/16 x 8 feet quarter
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationPatio Table. Page 1 of 16
Patio Table www.andrewharriswoodwork.com Page 1 of 16 Introduction This plan makes a table that is unit which is 95 ½ inches long and 49 inches wide. The distance from the underside of the top edging to
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 12 Introduction This plan makes a chest of drawers from 2 by 4s and 2 by 6s for the top. The cabinet is 22 ½ inches at the widest point, 22
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationComplete Dovetail Jig Instructions
Complete Dovetail Jig Instructions 15 18 4 3 1 12 13 8 19 17 16 6 14 5 9 11 10 2 9 PARTS LIST - Complete Dovetail Jig Introduction Your new dovetail jig will cut Full Through Dovetails and three varieties
More informationMaster Closet System [1]
[1] Submitted by Ana White [2] on Tue, 2011-04-19 00:36 Page 1 of 19 Page 2 of 19 [1] Additional Photos [3] [4] [5] [6] [7] You have all been down the closet aisle to know what $200 can buy you for organization.
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 4
Kentucky 4H Wood Science Plans Notebook Plans Level 4 MATERIALS NEEDED: Note: 1" wood may be 3/4" thick and 2" x 2" may be 1 1/2" x 1 1/2" 2 pieces wood 1 x 3 x 17 1 piece wood 1 x 3 x 14 3/4" 2 pieces
More informationMark out the centre lines of the cross plates on the side plates and drill small holes for panel pins, 3 or 4 should do, use a drill smaller than the
Powder Bins The design is for A5, with 10mm all round to aid part removal, with a part height of approx 180mm, this gives a machine that can produce a reasonable sized part without being to large. The
More informationMaking Pocket-Hole Joints
Tips and Techniques 8 SAFETY FIRST Making Pocket-Hole Joints Before doing this activity, make sure you understand how to use all of the tools and materials safely. Adding pocket-hole screws to strengthen
More informationPLANS BY TOM BURY JOB BUDDY TOTAL DIMENSIONS: 44 X 18 X 14 DIFFICULTY LEVEL: INTERMEDIATE
JOB BUDDY TOTAL DIMENSIONS: 44 X 18 X 14 DIFFICULTY LEVEL: INTERMEDIATE MATERIAL LIST: (5) 1 x4 x8 (2) 1 x4 x6 (1) 48 x48 3/4 plywood (1) 24 x24 metal mesh (1) 2 x 8 angle iron (1) 3 x 24 flat iron bar
More informationRustic X Kitchen Island - Double [1]
[1] Submitted by Ana White [2] on Mon, 2013-09-09 16:10 [1] I'm so glad you all liked the plans for the Small Rustic X Kitchen Island [3] built by Shanty2Chic [4]! Page 1 of 23 Page 2 of 23 Thanks for
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationEntryway Locker 17 ½ 25 ½
Copyright 2015 Shanty-2-Chic.com T Entryway Locker his old world entryway locker is loaded with possibilities. Two adjustable shelves allow you to customize the storage to fit your needs. Even better,
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationPROJECT PLAN TRAVEL CRIBBAGE BOARD
BUILD IT WITH ROCKLER PROJECT PLAN TRAVEL CRIBBAGE BOARD BUILD Stock # Item Stock # Item 59160 Small Cribbage Board Template, 2-Player, Straight Track 90638 3/4" Dia. Straight Router Bit (1/2" shank) 21026
More informationFITTINGS, SCREWS, BOLTS, ETC.
5mm Connecting 3 Mending Plate Order number... 19-116 For 5/8 to 5/8...19-168 For 3/4 to 3/4...19-170 Packaged 5 pieces Finish: Bright Nickel Packaged 5 pieces Finish: Zinc Plated Connecting Bracket For
More information-1- Coach Instructions.
-1- Coach Instructions. Insert the bogie pivot pins through the bottom of the coach body ensuring the dimples fit into the recesses. Glue the.06 x.25 short strips each side of the pivot head, bridge the
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 2.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationEco Office File Base. Materials and Tools: Free Plans to build an office file cabinet base
Materials and Tools: Materials: 1 - Sheet 3/4 PureBond Hardwood Plywood (Available at the Home Depot) 1 - Sheet 1/4 PureBond Hardwood Plywood (Available at the Home Depot) 3-21 Drawer Slides, Euro Style
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationCommercial Wine & Liquor Display. Double Displays
Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display
More informationYOU CAN BUILD THE JACKSON DRESSER. Combining traditional styling with rustic materials leads to a classic, yet casual look.
YOU CAN BUILD THE JACKSON DRESSER Combining traditional styling with rustic materials leads to a classic, yet casual look. Jeff Branch CONTENTS Jeff Branch Publisher: Jeff Branch Editor-in-Chief: Jeff
More informationThe first step is to cut all wood to proper size. Refer to the cutting schedule and Details 1 and 2 for further instructions.
CHILD S ARMOIRE 275 THIS CHILD'S ARMOIRE will make it easy for kids to keep their rooms neat and orderly. Its six drawers and two shelves provide enough storage space to house a substantial wardrobe. By
More informationDIY Rustic Dresser Addicted2DIY.com
DIY Rustic Dresser Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using
More informationPROJECT PLANS MULTIPURPOSE WORK CENTER
R PROJECT PLANS MULTIPURPOSE WORK CENTER This handy project can provide the work space you need anywhere in your home. Whether you need that work space in the shop, the garage, the basement, or in a laundry
More informationAdjustable Box Joint Jig. Richard Hicks on 8/24/2015. Box or Finger Joints
Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box or Finger Joints Adjustable Box Joint Jig Richard Hicks on 8/24/2015 Box Joints are also called Finger Joints Because they have interlocking fingers
More informationInstallation Manual MODEL E-42
Installation Manual MODEL E-42 GET TO KNOW YOUR UNIT 2 (BOTTOM OF RACEWAY) 1 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. ELECTRICAL OUTLET - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 3EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 3 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationMedia Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationAdjustable Countertop Installation
Adjustable Countertop Installation Applies to Models: A1, A2, A3, A4, A5, & A6 Required Tools: Stud Finder, Level 1/4 deep well socket, Screwdrivers, Tape Measure, Drill and Drill Bits Language of origin:
More informationShop Projects. Plans NOW. Each Built from One Sheet of Plywood!
Plans NOW www.plansnow.com 5 Shop Projects Each Built from One Sheet of Plywood! Tool Tote - Sawhorse - Workbench - Wood Bin - Wall Cabinet PLUS: 7 SHOP SECRETS Working with Plywood Dread the thought of
More informationThe Universal Table Saw Sled
The Universal Table Saw Sled Do Precision Work Even with Inexpensive Table Saws! Table saw blades always tend to move the wood while the cut is being made. This is why it's so difficult to get accurate
More informationProject 11355EZ: Wall Cabinet with Louvered Doors and Shelf
Project 11355EZ: Wall Cabinet with Louvered Doors and Shelf This Early American style cabinet will look good in any room, although it seems particularly well suited for the kitchen or bathroom. To make
More informationChief s Shop: Simple Woodworking Bench
Chief s Shop: Simple Woodworking Bench Be sure to read the instructions and review the illustrations and accompanying video for this project BEFORE you start. Follow ALL SAFETY GUIDELINES AND RECOMMENDATIONS
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationHow-to-Install. Laminate Countertops and Sheet Laminate. FREE brochure Reverso en español
FREE brochure Reverso en español How-to-Install Laminate Countertops and Easy to install instructions provided inside Multiple colors available for unique design options Durable and easy to care for Accessory
More informationA Magazine Rack with a Top
A Magazine Rack with a Top Introduction: I have never come across a good free plan for a magazine rack. Yet almost all homes have one. So this is one of the few items I have made on my own, as I don t
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationShaker Classic Change the legs to change the look
Shaker Classic Change the legs to change the look 2 Ways B Y C H R I S T I A N BECKSVOORT not long ago, a couple ordered a set of cherry side tables from me, one for each side of their pencil-post bed.
More informationRouter Table-Mate. Everything you'd want in a router table for just $50.
Router Table-Mate Everything you'd want in a router table for just $50. Commercially made router tables are everywhere these days. Some of them come with more gizmos and gadgets than a 59 Edsel. By the
More informationWoodline USA Woodline Spacer Fence System
Woodline USA Woodline Spacer Fence System MADE IN THE USA Includes: (1) ¼ Spacer Fence (1) 3/8 Spacer Fence (1) ½ Spacer Fence (1) Hardware Package (1) 3 Piece Brass bar set (2) Setup Blocks Visit Us Online
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM 4 BI (Built-In) Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship
More informationTryde Media Hutch. Copyrighted Material. Page 1
Compare to: Pottery Barn Hyde Media Console Skill Level: Intermediate Tryde Media Hutch Following the great success of so many readers with the Tryde Collection, inspired by Pottery Barn s popular Hyde
More informationReclaimed Wood Look Bedside Table [1]
[1] Submitted by Ana White [2] on Thu, 2011-06-23 12:27 Page 1 of 18 [1] Additional Photos Page 2 of 18 [3] Featured photo by brick [4] This rustic three drawer nightstand is easy to build with off the
More informationMaking a Massive Bookcase Step-by-Step
Making a Massive Bookcase Step-by-Step Jeff Branch WOODWORKING The only thing challenging about this project is its huge size. By JFF BRANCH A t right is a rendering of my first woodworking project completed
More informationDIY Full-Size Captain s Bed with Storage. Addicted2DIY.com
DIY Full-Size Captain s Bed with Storage Addicted2DIY.com Before beginning this project Please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationGrilling Table. Page 1 of 10
Grilling Table www.andrewharriswoodwork.com Page 1 of 10 Introduction This plan makes a table 47 inches wide, 22 inches deep and 36 inches high with the top added. All my builds are made with pocket hole
More informationrmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only
A rmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only a little over 1 foot deep, it s easy to incorporate
More informationPreference Collection 5543 Central Console INSTALLATION GUIDE
Preference Collection 5543 Central Console INSTALLATION GUIDE WARNING Failure to install the 5543 as described in this installation guide may cause the unit to collapse, resulting in serious injury to
More information