MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A335

Size: px

Start display at page:

Download "MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A335"

Rose Glenn
5 years ago
Views:

1 OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 3 3 APPROPRIATE USE 3 4 TECNICAL DATA 3 5 CHART OF TYPES A OPERATION 4 7 SPARE PARTS LIST SEAL CONTROL en/MAS/ SEAL ADJUSTMENT CLEANING ACCESSORIES 12

2 1 SAFETY INSTRUCTIONS Read these instructions carefully. Failure to follow these instructions can result in severe personal injury. Eye injury hazard Failure to wear safety glasses with side shields can result in severe eye injury or blindness. Always wear safety glasses with side shields which conform to ANSI Standard Z87.1. Strap breakage hazard Improper operation of the tool, excessive tensioning, using strap not recommended for this tool or sharp corners on the load can result in a sudden loss of strap tension or in strap breakage during tensioning, which could result in the following: A sudden loss of balance causing you to fall. Both tool and strap flying violently towards your face. Note as follows: Operation Tool must not be used by persons not properly trained in their use. Before tensioning strap, read and understand the tool operating instructions. Failure to follow the operating instructions or improper load positioning could result in strap breakage. Become familiar with your tool and keep fingers away from areas that can pinch or cut. Joints You are fully responsible to review the joints made by your tool. Become familiar with the seal control and seal adjustment described in this operation manual. Misformed joints may not secure the load and could cause serious injury. Never handle or ship any load with improperly formed joints. Dispensing strap Only dispense strap from a dispenser specifically designed for strap. Tuck strap end back into dispenser when not in use. Protective gloves When handling strap, always wear protective gloves. If the load corners are sharp, use edge protectors. Place the strap correctly around a properly positioned load. Positioning yourself in-line with the strap, during tensioning and sealing, can result in severe personal injury from flying strap or tool. When tensioning or sealing, position yourself to one side of the strap and keep all bystanders away. Use the correct strap quality, strap width, strap gauge and strap tensile strength recommended in this manual for your tool. Using strap not recommended for this tool can result in strap breakage during tensioning. Cutting tensioned strap When cutting strapping, use the proper strapping cutter and keep other personnel and yourself at a safe distance from the strap. Always stand to side of the strap, away from the direction the loosened strap end will fly. Use only cutters designed for strap and never hammers, pliers, hacksaws, axes, etc. Fall hazard Keep your working area tidy. Untidiness of your working area may cause a risk of injury. Maintaining improper footing and/or balance when operating the tool can cause you to fall. Before tensioning and especially in elevated areas, always establish good balance. Both feet should be securely placed on a flat, solid surface, especially when working in elevated areas. Do not use the tool when you are in an awkward position. Pay attention to the rules and regulations for preventions of accident which are valid for the work place. Strap warnings Never use strap as a means of pulling or lifting loads. Failure to follow these warnings can result in severe personal injury. Tool hazards A well maintained tool is a safe tool! Check tool regularly for broken or worn parts. Do not operate a tool with broken or worn parts. Never modify any tool. Modification can result in severe bodily injury. 2 A335T1.en.fm

3 2 WARRANTY CONDITIONS AND LIABILITY FROMM Holding AG warrants all its strapping tools and machine heads during a period of 90 days from the date of sale. The warranty includes all deficiencies clearly resulting from poor manufacturing or faulty materials. Damage claims as a result of production shutdowns and claims for damage to persons and to property resulting from warranty deficiencies cannot be asserted by the customer. The warranty excludes: wearing parts deficiencies resulting from improper installing, incorrect handling and maintaining the tool deficiencies resulting from using the tool without or with defective security- and safety devices disregard of directions in the operation manual arbitrary modifications of the tool deficient control of wearing parts deficient repair works of the tool Use of consumable products not recommended by FROMM Holding AG We reserve the right to modify the product at any time in order to improve its quality. 3 APPROPRIATE USE The tool model A335 has been designed to strap packages with steel strapping exclusively. The warranty / liability excludes: non appropriate use of the tool, disregard of directions in the operation manual, disregard of control- and maintenance instructions. 4 TECNICAL DATA Dimensions without suspension bracket Tool Package Length: 387 mm / 15.2" 410 mm / 16.1" Width: 162 mm / 6.4" 360 mm / 14.2" Height: 308 mm / 12.1" 170 mm / 6.7" Weight: 3.9 kg / 8.6 lbs 1.2 kg / 2.7 lbs Joint strength Approx. 80% of the strap s tensile strength. Steel strapping Width: mm / 1/2"-3/4" (see chart of types) Thickness: mm / 0.020" " Quality: Fundamentally the A335 allows the use of all current steel straps with tensile strengths ranging from 850 to 1100 N/mm 2 / psi. Straps with a low breaking elongation are unsuitable. A335T1.en.fm 3

4 5 CHART OF TYPES A335 Item No. Model Strap width Strap thickness A335/12.7/ mm / 1/2" mm / " A335/13/ mm mm / " A335/16/ mm / 5/8" mm / " A335/19/ mm/ 3/4" mm / " 6 OPERATION When handling strap, always wear protective gloves and safety glasses with side shields which conform to ANSI Standard Z87.1. Feeding the strapping around the package The strapping is fed around the package in the direction as shown in the illustration. The strapping end is held tightly with the left hand and pulled firmly towards the operator with the right hand. Loading the strapping The rocker is raised with the right hand. The left hand inserts the two straps lying precisely upon another into the tool until they hit the strap stops. The lower strap end must slightly protrude the end of the base plate. Be certain that the strapping is held by the strap guide. 4 A335T1.en.fm

5 Tensioning the strapping The tool is held tightly with the left hand being placed on the sealing lever. The tensioning handle is now moved forward and backward with the right hand until the desired tension is attained. Sealing the strapping The sealing lever is moved forward using the left hand until it hits the stop. The lever is then moved back to its initial position. When sealing, the right hand absorbs the sealing force by holding the tensioning handle. Releasing the tool Hold the cut off strap end with the left hand, lift the rocker with the right hand and push the tool from the applied strap to the right. A335T1.en.fm 5

6 A N A N B N Œ N A Œ N Œ N N N N Ž A N Œ N Œ N Œ A A A Œ A A N N A C N N N A N N A N N A D A N Œ A N N A Œ A E A A N A N N z N1.1304

7 A N N A N N N N N A N N A N N A N x A N A N A N A N x N A A N A A N N A N N N A N N N N A N A Œ ESSO Beacon 2 Loctite 222 Ž Loctite 243 Loctite Nm 85 Nm Compensation

8 7 SPARE PARTS LIST A335/19/ A Item-No. in group Pcs. Description Dimension Field A * 1 SHEAR BLADE D5 A SEALING HANDLE A4 A STOP C3 A BUSH C3 A SOCKET SET SCREW C5 A A ROLLER D4 A A LINK D4 A EJECTOR A5 A * 1 DIE HALF E3 A * 1 DIE HALF E3 [A ] 1 SHIM C3 A COVER C6 A WASHER B4 A WASHER B5 A TRUNNION B3 A SEALING CAM B5 [A ] 1 HOUSING C5 [A ] A DIE AND CUTTER SUPPORT D3 A COVER C6 [A ] 1 DIE AND CUTTER SUPPORT D3 A LIMIT BOLT D3 A STRAP STOP D5 A * 1 PUNCH E3 A BASE PLATE E5 A * 1 GRIPPER HSS E5 A TENSIONING PAWL B2 A RING HALF B2 A ROCKER B6 A LOCKING RING B3 A DRIVER B2 A STRAP GUIDE C5 A * 3 CATCH PAWL B2 A SPACER RING C5 A * 1 TENSIONING WHEEL C5 [A ] 1 TENSION SHAFT B2 A TENSION HANDLE A3 N SCREW M8 X 20 E4 N SCREW M5 X 8 D5 N A SCREW M8 X 10 B3 N SCREW M5 X 16 C3 N SCREW M5 X 12 D5 N SCREW M10 X 1 X 80 B3 N SCREW M12 X 1,25 X 80 B5 N SCREW M5 X 10 B4 N SCREW M6 X 25 B2 N SCREW M3 X 8 E4 N SCREW M4 X 10 D4+ N SCREW M4 X 10 D6 N SOCKET SET SCREW M5 X 6 E3 N SOCKET SET SCREW M5 X 25 B6 N SOCKET SET SCREW M12 X 12 C3 [ ] = Group * = Wearing parts een.fm

9 A335/19/ A Item-No. in group Pcs. Description Dimension Field N SOCKET SET SCREW M4 X 8 C3 N HEXAGON NUT M5 B6 N HEXACON NUT M6 B3 N WASHER 5.3 X 9.5 X 1 C3 N WASHER 15.2 X 24 X 1 C6 N SECURITY RING E20 B1 N SECURITY RING E14 C6 N A PARALLEL PIN 4 H6 X 10 E5 N A PARALLEL PIN 5 H6 X 16 D3 N PARALLEL PIN 3 M6 X 10 E4 N A PARALLEL PIN 14 H6 X 48 D3 N PARALLEL PIN 14 H6 X 48 B3 N PARALLEL PIN 4 H6 X 22 E4 N PARALLEL PIN 10 H6 X 65 B6 N PARALLEL PIN 4M6 X 34 C5 N PARALLEL PIN 5 H8 X 60 C3 N DOWEL PIN 3 X 10 E5 N DOWEL PIN 6 X 20 MM B5 N GROOVED PIN 6 X 16 A3 N WOODRUFF KEY 5 X 7,5 X 18,57 B2 N HAMMER HEAD BOLT 1,85 X 4,76 B4 N HAMMER HEAD BOLT 5,31 X 12,7 B5 N PRESSURE SPRING 0.45 X 3.9 X 7 B2 N PRESSURE SPRING 2 X 9.8 X 96 B5 N PRESSURE SPRING 1 X 8 X 26 C5 N CUP SPRING 40X20.4X1 B2 N TORSION SPRING C3 N NEEDLE BEARING B3 N NEEDLE BUSH C6 N A SLIDE-BEARING D4+ N SLIDE-BEARING C5+ N ADHESIVE LABEL A5 N LABEL A335 B4 N GRIP BALL A3+ [ ] = Group * = Wearing parts een.fm 9

10 8 SEAL CONTROL A regular control of the seal is necessary. The seal can be checked visually and the person controlling can easily judge the quality of the seal. When checking the seal the following illustrations must be compared. Correct seal A correct seal must be conform to the illustration. This means that the depth with which the upper strap hooks into the lower one must be 1-1,5 mm in min. and 2 mm in max.. The upper strap must be sheared clean and the cutter must not leave scratch marks on the lower strap. Incorrect seal (the sealing mechanism is adjusted too high) This stamped seal is not deep enough and the upper strap is not sheared.the tensile strength of this seal is insufficient and the strapping must be taken away from the package. The tool must be readjusted immediately (see SEAL ADJUSTMENT). Incorrect seal (the sealing mechanism is adjusted too low) This stamped seal is too deep and the lower strap is scratched by the cutter. Although the tensile strength of this seal is sufficient the strapping must be taken away from the package because of the scratched lower strap. The tool must be readjusted immediately (see SEAL ADJUSTMENT). 10 A335T2.en.fm

11 9 SEAL ADJUSTMENT The sealing and cutting depth of the sealing mechanism and the cutter can be adjusted with the use of the hexagon key N which is supplied with the tool as follows: Place tool as shown above. Loosen both screws N and open them by approx. 3 revolutions. If sealing depth is not sufficient reset stop in the direction of the base plate. If sealing depth is excessive reset stop in the direction of the body cover. Retighten screws N Assembly Instructions After every disassembly it is essential to retighten screws N and N with the recommended torque when reassembling. The use of a torque key is necessary. N1.1182=42 Nm N1.1184=85 Nm 10 CLEANING In case of heavy dirt and when painted straps are used the punch, dies, gripper and feed-wheel must be cleaned regularly. Normally it is sufficient to blow out the parts with the help of an air gun. A335T2.en.fm 11

12 11 ACCESSORIES Using tool with horizontal handle Upon request the tool can be supplied with a bolt A and a grip ball N When using tool for horizontal applications, the operator holds the tool on the grip ball during tensioning. Install the handle as follows: Remove side cover A and break the marked position. Reassemble side cover and screw bolt with mounted ball into the body. Suspension It is possible to suspend the tool for strapping in vertical position. Order the suitable suspension separately under item no. A A335T2.en.fm

MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A332

OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A332 13.2250.01 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 3 3 APPROPRIATE USE 3 4 TECNICAL DATA