Swivel Bracket (1) Ladder frame (1) Wrench or Socket (2) 9/16inch 13mm

Size: px

Start display at page:

Download "Swivel Bracket (1) Ladder frame (1) Wrench or Socket (2) 9/16inch 13mm"

Sylvia Newman
5 years ago
Views:

1 XLD-Base Assembly and Instructions Thank you for purchasing VFI's XLD display mounting system. This product was designed for mobile mounting of a single flatscreen TV sized " or dual flatscreens sized 32-52" with appropriate bracket kit. Some larger TV's will fit, Download TV manufacturers specs online, Max hole locations are 1100mm w x 650mm h single or 700mm w x 440mm h for duals. Note: 2 persons are required to attach plasma/lcd TV's to this mount. If you cannot understand these instructions or are concerned about the safety of the installation Contact a qualified contractor or contact VFI at Confirm all parts are included before you begin assembly. Not all hardware supplied will be used depending on the manufacturer of your display/s. Read these intructions start to finish before beginning installation. Supplied Parts: (TV brackets are in another box) Page 1 of 7 Caster (2) Locking Caster (2) Base Front Swivel Bracket Side Handle (2) Cam Tongue Main Pillar Left Right Base Rear Ladder frame Cam Neck Cover Cam Neck Supplied Hardware: XLD BAG Wingnut (4) M8 x 12 (14) Spring Washer (24) M8 Lock Nut (20) M10 x 20 (4) Hex Key 6mm Hex Key 8mm M8 x 20 (26) Tools required: (not supplied) Wrench or Socket (2) 9/16inch 13mm Tape Measure

2 Step 1 Assemble the Base Page 2 of 7 M8 X 20 (4) Springwashers(4) Using included Hex key and smallest of the M8 bolts Loosely fasten all four bolts. Do not tighten till end of step 2. Step 2 Attach pillars to base M8 X 20 (6) Springwashers(6) Same Tool and Bolts Fasten and tighten all 6 bolts. Flip over and tighten Step 1 Bolts. Make sure these holes are facing outside. Step 3 Attach handles Same Tool Attach handles. Fasten and tighten all 8 bolts. M8 X 12 (8) Springwashers(8)

3 Step 4 Add the Ladder frame Page 3 of 7 Same Tool and Bolts Insert Ladder frame. Fasten and tighten all 4 bolts. M8 X 12 (4) Springwashers(4) Step 5 Screw in Casters *Gently tip the frame on its back. *Lock the brakes on the casters. *Screw in Casters into existing threads. Make sure to install braking ones on front. Step 6 Attach Swivel Bracket 8mm Hex Key Largest Hex key and M10 bolts. Warning: This part is heavy. Insert top bolt first. If swivel setup is going to be used,insert second bolt through slotted hole. For no swivel, use other bolt hole. Note: Swivel setup is meant for M10 X 20 (4)

4 Step 7 Adding TV Bracket/s Page 4 of 7 (TV brackets are sold separately) 13mm Wrench M8 X 20 Bolt(8) M8 Nuts (8) Adding a XLD-XL Bracket Adding a XLD-D Bracket M8 X 20 Bolt(4) M8 Nuts (4) M8 X 20 Bolt(8) M8 Nuts (8) M8 X 45 Bolt(4) M8 Nuts (4)

5 Step 8 Attaching TV brackets Page 5 of 7 Note.Have 2 people lift the TV as it can be very heavy and awkward. Hex Key 1.Place TV face down on blanket or non abrasive surface such as cardboard. 2.Check to see if your TV came with mounting hardware. If not,we have supplied the most common hardware. Most TV manuals list the required thread and depth for mounting hardware. See which bolt length you need by hand tightening only. 3.Place TV brackets so you can see the TV mounting holes through the bracket and insert bolt through appropriate washer and spring washer for depth adjustment. 4.Use the Hex key to tighten until there is resistance, then give a half turn. DO NOT OVERTIGHTEN AS THIS CAN DAMAGE OR PUNCTURE THE TV Optional Spacer mounting Appropriate bolt. Washers if required TV Bracket Spacer Spacer is used when the back of TV is not flat or the mount holes are sunk into the back of the TV. (Rarely used) (XLD Bracket shown) Dual brackets have no crossbar.

6 Step 9 Hanging TV's and locking into place Page 6 of 7 (XLD Bracket shown) Hex key Hang the TV,First Hooking the top of the mounting bracket rail then allowing the TV to rest on the rail. Make sure Bolts clear bracket, TV will tilt until its flush with the mount, Turn bolt until it catches on the bracket. Note: Two people should lift and secure the TV Once your TV is centered. Completely tighten bolts against metal bracket and brace.

7 Step 10 Attaching camera bracket Page 7 of 7 Hex key 13mm Wrench Using smaller hex key, Attach the camera tongue to the Camera Neck. M8 X 12 (2) M8 Nuts (4) Hang Cam Neck at desired height above or below TV's and secure using 4 M8 nuts and wrench. Upper Camera Lower Camera Wingnuts (4) Mfter attaching camera using 1/4-20 bolt, run wires through neck and secure cover using included wing nuts. You're Done!

STEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION

STEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions