VINYL REPLACEMENT WINDOW INSTALLATION STANDARDS
|
|
- Rodney Wilkins
- 5 years ago
- Views:
Transcription
1 VINYL REPLACEMENT WINDOW INSTALLATION STANDARDS BEFORE you start to remove the existing windows Place clean drop cloths in all work areas. Re-measure the opening to ensure the new window will fit. Remove one existing window at a time and install the new window BEFORE moving to the next one. Generally, the new window can be installed from the inside or outside. However, if the interior moldings are stained or painted, or of a particularly high quality, an outside installation is recommended. Removal of Existing Window / Preparing the Opening DO NOT break the glass out of the existing windows. Always place duct tape over any glass BEFORE removing to prevent shattering. Clean all loose debris from the opening. Replace rotted wood ONLY if specified on the Spec. Sheet (or get approval for 2 nd Labor Bill from Project Manager). Review the manufacturer s instructions prior to installation. Interior & Exterior Stops All windows should have interior and exterior stops. Reuse existing stops whenever possible. If the interior stop breaks when it is removed, install a new stain grade stop (try to match the old stops if possible). If exterior stops CANNOT be reused (or if there was no exterior stop), install new exterior stops using ripped plywood or dimensional lumber. When replacing a METAL WINDOW with a 6000 series window, use 2 Piece Snap Trim to replace the INTERIOR stops. Miter the corners on the Snap Trim. Installing the Sill Extender / Sill Angle 6000 series Windows Use the sill track built into the bottom of the window and snap the sill extender into position. The sill extender is not to be used as a support piece IHB-IR-IS-W-VW 1
2 Back caulk the sill track prior to snapping the sill extender on. American Craftsman Windows Position the sill angle under the lip of the frame. Do NOT nail the sill angle in place. Shimming All window openings should be shimmed as needed (preferably near the screw hole locations) to make the window level, plumb and square. For 6000 series windows, additional adjustments can be made using the jamb adjusting screws or wood block adjusters (depending on the style of window). DO NOT over-tighten the adjusters as this may interfere with the operation of the window. Installation screws should penetrate the shims whenever possible. Insulation Install fiberglass insulation generously around the frame and fill any air gaps. DO NOT use expanding foam insulation. Installation Screw Holes If additional screw holes are needed, drill a pilot hole prior to installing the screw. Screws should be flush with the inside of the balance track so they do not interfere with the sash operation. Never screw through a windowsill IHB-IR-IS-W-VW 2
3 Preventing Whistling in Double Hungs Double Hung windows may experience a wind draft along the balance tracks causing a whistling or chimney effect sound. To prevent this: Make sure all installation screw holes (both those pre-drilled at the factory and any additional holes made by the installer) are completely sealed with silicone. Install Foam Installation Plugs (for 6000 series windows) or Chimney Blocks (for American Craftsman windows) just below the tilt latches in the balance channel. Apply a dab of caulk to secure the plugs or blocks in the channel. For 6000 series windows, black mesh screen material can also be inserted into the weep hole to reduce wind infiltration. Window/Door Wraps Always use PVC Aluminum Coil to wrap the window/door casings, unless the Spec. Sheet specifies to match the existing wraps. If you are not sure what to use, call the PM. Install wraps in a weather-tight fashion (weatherboard method) to prevent water infiltration. ALL CORNERS ARE TO BE MITERED (unless specified otherwise), but NOT caulked. Pre-drill all coil material with a 1/8 bit before nailing the coil. Keep face nailing to a minimum. Caulking BE VERY NEAT! Always color match caulking to the window. For EXTERIOR caulking, use 100% silicone caulking. For INTERIOR caulking, use paintable caulking. Always back-caulk on the interior side of the exterior stops and the exterior side of the interior stops. Insert the new window into the opening and press it against the caulked stops. Caulk the entire perimeter of the window (interior & exterior) to prevent air and water infiltration. NEVER caulk over the weep holes! IHB-IR-IS-W-VW 3
4 Cleaning A CLEAN, PROFESSIONAL INSTALLATION IS CRITICAL TO CUSTOMER SATISFACTION. Remove all stickers and adhesive residue. Some local building authorities want to see the stickers on the glass during their final inspection. CLEAN the glass (inside & outside), the frame and all capping. Pick up any glass, nails, coil pieces and debris. Make sure that all work areas have been thoroughly cleaned. Final Inspection Check the operation of all units. Check that all locks, keepers and latches are aligned and secure (repair/replace as needed). Check that no screens are torn (repair as needed). If any lubrication is needed, use a dry silicone spray, NOT a petroleumbased lubricant like WD-40. Make sure all wraps & stops are properly positioned and secure. AFTER checking the windows, walk the home with the customer and demonstrate the operation of each new window. Show the homeowner how to: tilt in sashes, remove & re-install sashes (using the pivot bar), operate locks (& cranks), operate air latches, remove & reinstall screens. The final walk through with the customer is an important step toward preventing service calls. Ten minutes with the customer will prevent hours of time wasted on a service call IHB-IR-IS-W-VW 4
5 STANDARDS FOR SPECIFIC WINDOW TYPES Refer to Manufacturer s Instructions on Window Sticker. Wood Removal Carefully score the paint line between the interior stop and the window casing. Cut the exterior blind stops carefully so they can be re-used. Aluminum Window Removal Remove the sash inserts, if possible. If the sashes cannot be removed, remove the glazing around the perimeter of the glass and take out the glass unit. Use a heat gun to remove the glass if it is glued to the sash. Collapse the frame and remove it. If the nailing flange is behind asbestos shingles or masonry, cut the nailing flange along the perimeter of the frame and leave the nailing flange in place. Steel Window Removal If the steel windows have an interior pan, the pan should NOT be removed and a Buck Frame should be installed. Install or re-use interior & exterior stops. Mulled Units Attach plywood to the bottom of the opening to support the windows. DO NOT screw through the windowsill! Inspect all factory-caulked joints (especially at mullions), as they may become loose during shipping. Reapply caulking as needed. Field Mulled Units (Silver Line ONLY): Install windows with a continuous head expander and sill angle. Apply silicone caulk generously to the H mullion. Keep the units tight to the "H" mullion for maximum support IHB-IR-IS-W-VW 5
6 Casement Windows If installing over a sloped sill, attach wood to the sill and level it before installing the window. Install two screws into the hinge side screw holes. For 6000 series windows: Remove the screws at the ends of the bottom & top hinge tracks and replace them with installation screws. Remove the screws from both the lower and upper sections of the locking bar (on the keeper side of the frame) and replace them with installation screws. (An additional screw in the middle of the locking bar may be needed for taller windows). Caulk and insert the screw hole covers to prevent water infiltration. Awning Windows ( 6000 series Only) If installing over a sloped sill, attach wood to the sill and level it before installing the window. Remove one of the two screws closest to the center of the sill and replace it with an installation screw. Replace the second screw from the top and the closest screw to the bottom with installation screws. Install one screw in each predrilled installation hole in the head. Caulk and insert the screw hole covers to prevent water infiltration. Single, 2 and 3 Panel Sliders If installing over a sloped sill, attach wood to the sill and level it before installing the window. If the header requires additional support, predrill an installation hole, fill it with silicone caulk and install an installation screw. When removing & reinstalling sashes, make sure they clear the security clip in the frame. Patio & Garden Doors Generously caulk the underside of the sill. DO NOT over-tighten the screws in the sill (this will allow the door to slide freely). In the case of Patio Doors, install the moving panel(s) first and lock into place before installing the fixed panel(s). Check that the lock engages the keeper from below. Caulk the top and bottom of the fixed panel(s) IHB-IR-IS-W-VW 6
7 Bay & Bow Windows Measure the width (from stud to stud) and the height (from header to sill plate) to confirm the new window will fit. Check that the wall of the house is plumb. The window must be installed directly to the original-framing studs. Back caulk the F Channel and all four sides of the rough opening prior to inserting the unit. Cable support system (which comes with every Bay/Bow window) should be attached to a structurally sound framing area above the opening above the window. Support the nose of the unit from the outside while attaching the cable system and use the adjustment rods (on the underside of the seatboard) to set the unit to approx. 1/8 above level to allow for cable stretch. Remove the ¼ wood veneer covering the jambs and install screws every 8 to 12 apart. Glue the veneer back on. Do not screw through the headboard or seatbord. Install knee braces under the mitered angles of the unit. Knee Braces are provided with units that have a 7 projection or greater. The knee braces are pre-finished and do not require wraps. Knee Braces must be secured to a solid surface (stud or brick). Caulk! Caulk! Caulk! Especially on the exterior where the header meets the window frame. Inspect all factory-caulked joints (especially at mullions), as they may become loose during shipping. Reapply with caulking provided. Insulate the top of the unit with fiberglass insulation. The importance of this can not be stressed enough! The insulation will help reduce drafts and prevent the formation of ice. If constructing a new roof, use a combination of Ice and Water Shield and aluminum step flashing along the sidewall and roof edges. Use continuous flashing where the roof meets the house. New interior casing (stain grade) should match what the customer ordered (Colonial or Clamshell). New casing should cover any unfinished or damaged areas IHB-IR-IS-W-VW 7
Replacement Windows Measuring & Installation Guide
Proper Measuring Proper Measuring of Typical Wood Openings Replacement windows are ordered and manufactured E.B. (Exact Both) size, exact width and exact height. Windows are manufactured to the nearest
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationNEW CONSTRUCTION, REPLACEMENT AND FLUSH FIN REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS
NEW CONSTUCTION, REPLACEMENT & FLUSH FIN WINDOWS NEW CONSTRUCTION, REPLACEMENT AND FLUSH FIN REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS IMPORTANT! READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationCasement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer)
Casement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Caulk Gun Hammer Safety Glasses
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationVINYL WINDOWS (new construction or replacement) page 2. VINYL PATIO DOORS pages WOOD CLAD WINDOWS (new construction).page 5 WOOD CLAD WINDOWS
RECOMMENDED INSTALLATION INSTRUCTIONS Please choose the appropriate instructions for the product(s) you are using. Read the instructions thoroughly before beginning the installation process. All instructions
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationUNIT 5: EXTERIOR DOORS AND WINDOWS
KEY CONCEPTS 1. Identify tools needed for exterior door and window installation 2. Last step to weather proofing the home 3. Steps to installing exterior doors and windows 4. Maintenance and safety of
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationPicture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer) Fig.
Picture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Foam Gun (Optional) Caulk Gun Hammer Safety
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationMeasuring & Ordering Guide
Measuring & Ordering Guide Replacement Vinyl Windows & Patio Doors that fit by Thermo-Fit custom replacement vinyl windows & patio doors by Thermo-Tech are designed to fit your lifestyle for low-maintenance
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationWINDOW INSTALLATION GUIDE
WINDOW INSTALLATION GUIDE SAWDAC is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.
More informationAssembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame
Assembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame americancraftsmanwindows.com American Craftsman and all other marks where denoted are trademarks of Andersen Corporation
More informationNorwood Windows Permaglass Fiberglass Products Installation Instruction
Norwood Windows Permaglass Fiberglass Products Installation Instruction Care and storage of fiberglass windows: Fiberglass products purchased from Norwood Windows must be stored in a dry sheltered area
More informationThermally Broken Framing and Door Installation
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationPocket Door Installation Instructions
Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationInstallation Guide for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows
for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationINSTALLATION INSTRUCTIONS for Vinyl Projecting Windows with Integral Nailing Fin (JII023)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl bay, bow and garden windows which incorporate an integral nailing fin. While the use of
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationTHERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE)
THERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE) fig.3 Casement, Awning, Fixed Casement, Direct-Set, Double-Hung, Single-Hung & Horizontal Slider Windows Materials
More informationSash Replacement Guide for Andersen Impact Resistant Casement Windows
Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006
for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationVinyl Windows Manufactured by VPI Quality Windows
Vinyl Windows Manufactured by VPI Quality Windows Part Number: 531&591 Installation 531 & 591 SERIES SLIDING AND HUNG WINDOW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction.
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032)
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More informationVinyl Windows and Doors Manufactured by VPI Quality Windows
Vinyl Windows and Doors Manufactured by VPI Quality Windows Part Number: 511_Installation ENDURANCE CASEMENT\AWNING\PW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These
More informationInstallation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
www.quakerwindows.comv www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows
for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationFrequently Asked Questions
1. What is the difference between new construction and retrofit? The difference is in the overall jamb depth and required components: For new construction, the flash flange on the head of the unit is left
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationInstallation Guide for Andersen Architectural Clad Awning Windows
Guide for Andersen Architectural Clad Awning Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationInStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled
InStallatIon InStruCtIonS for vinyl -lite PatIo door assembled tools & materials you Will need: Measuring Tape Pencil Shims Square Hammer or Mallet Level Drill & Drill bits: 6", 8", 5 6", 7 6" Utility
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationInstallatIon InstructIons for 2-lIte PatIo Door unassembled
InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationBefore installation, check your local and state requirements for this type of install.
1 Remove Packaging & Inspect Your Patio Door Remove shipping materials such as corner covers or pads. 2 Inspect Rough Opening Verify that the width and height of the patio door are each 1/2" to 3/4" smaller
More informationInstallation Recommendations for Finless Frame Doors
Installation Recommendations for Finless Frame Doors These installation recommendations are made available by MI Windows and Doors, LLC (MI) to assist with the integration of finless or flange sliding
More informationWEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS
CORE WEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS Removing Old Windows Part II - Frame Out Although all possible measures have been taken to insure the accuracy of the material
More informationPlease read and understand all instructions before beginning. These instructions cover the non-impact aluminum French Door 101.
The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand
More informationINSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION & GLOSSARY ROUGH OPENINGS
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
More informationFrequently Asked Questions
1. What is the difference between new construction and retrofit? The difference is in the overall jamb depth and required components: For new construction, the flash flange on the head of the unit is left
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS
WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems
More informationPELLA INSTALLATION INSTRUCTIONS - ADVANCED PERFORMANCE Nail Fin, Nail Fin with J-Channel and EnduraClad Exterior Trim with Nail Fin Windows
PELLA INSTALLATION INSTRUCTIONS - ADVANCED PERFORMANCE Nail Fin, Nail Fin with J-Channel and EnduraClad Exterior Trim with Nail Fin Windows THE FOLLOWING INSTALLATION METHODS ARE INCLUDED IN THIS BOOKLET:
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationInstallation Guide for Andersen Architectural Clad Hinged Windows
Guide for Andersen Architectural Clad Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationPlease read and understand all instructions before beginning. These instructions cover the non-impact aluminum sliding glass door.
The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG, CASEMENT, AWNING INTO EXISTING CASEMENT FRAME USING FRAME SCREWS
2009 Pella Corporation Part Number: 80YV0102 WINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG,, AWNING INTO EXISTING FRAME USING FRAME SCREWS These instructions were tested and developed for
More informationInSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled
InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty
More information70 Series. Preferred Replacement Bay and Bow Windows
70 Series Preferred Replacement Bay and Bow Windows Andersen Corporation, including its subsidiary Silver ine Building Products C, earned the 2010 ENERGY STAR Partner of the Year award. Preferred Replacement
More informationINSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS.
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the owner. Please read
More informationWEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS
CORE WEB BASED CORE APPLICATION SPECIFIC INSTALLATION INFORMATION AND METHODS Removing Old Windows Part I - Frame In Although all possible measures have been taken to insure the accuracy of the material
More informationMetal & Vinyl, Flush Mount and Recessed Fin Windows Recommended Installation Instructions
PO Box 480 Ph: 417-235-7821 Monett, MO 65708 Fax: 417-737-7140 Metal & Vinyl, Flush Mount and Recessed Fin Windows Recommended Installation Instructions These installation instructions are recommendations
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More information6400, 8400 and 9400 Series Sliding Patio Door
Contemporary 3 Panel Classic 5 Panel French Panel 6400, 8400 and 9400 Series Sliding Patio Door (O) Fixed Panel Left (X) Operating / Mullion Panel Right (X) Operating / Lock Panel Left (O) Fixed Panel
More informationInstallation Instructions for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nail fin. Not all window types may be installed into every wall
More informationINSTALLATION INSTRUCTIONS for Vinyl Projecting Windows with Integral Nailing Fin (JII023) IMPORTANT INFORMATION AND GLOSSARY ROUGH OPENINGS
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl bay, bow and garden windows which incorporate an integral nailing fin. Read these instructions
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges
More informationVinyl Windows and Doors
Vinyl Windows and Doors Manufactured by Pella Corporation Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. Part Number: V981555 2009 Pella Corporation
More informationPanel Assembly and Installation
Assembly and Installation Assembly and Installation for Andersen 400 Series Frenchwood, 200 Series Narroline, 200 Series Perma-Shield Gliding Patio Doors and 400 Series Perma-Shield Gliding Patio Doors
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More informationPREHUNG DOOR SYSTEM INSTALLATION INSTRUCTIONS: FIBRECOMP COMBINATION UNITS
PREHUNG DOOR SYSTEM INSTALLATION INSTRUCTIONS: FIBRECOMP COMBINATION UNITS Read all instructions before starting. Calgary Toll Free: 1-866-664-7664 Saskatoon Toll Free: 1-800-667-6977 Winnipeg Toll Free:
More information(773) INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001) IMPORTANT INFORMATION & GL OSSARY ROUGH OPENINGS
Thank you for selecting C l i m a t e G u a r d products. Attached are our recommended installation instructions for Vinyl windows with an integral (2400-02) will not affect application of the ClimateGuard
More informationINSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationINSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
2008 Pella Corporation Part Number: 80KG0101 INSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD Note: These instructions may be used for all Pella Bow windows that do not have a
More informationInstallation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors
Installation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More information392CV SERIES Stickstall
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com 392CV SERIES Stickstall TM Corner Shower Enclosure 392CV-1117 Yes!
More informationINSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO
2008 Pella Corporation Part Number: 801V0101 INSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows with Exterior Trim or Nail Fin (JII024)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows with nailing fin or primed wood windows with exterior trim. While the
More informationInstallation Instructions
edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung
More informationREAD BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION
edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully
More informationINSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2012 Pella Corporation Part Number: 80WH0101 INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Installation Instructions for Typical Wood Frame Construction.
More informationInstallation Guide for Andersen 400 Series Gliding Windows
for Andersen 400 Series Gliding Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits of your
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Wood Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationINSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español
More information8/7/ HP SWING DOOR INSTALLATION INSTRUCTIONS
8/7/17 1200 HP SWING DOOR INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These instructions were developed and tested for use with typical construction in a wall system designed
More informationVISTALUXE CASEMENT, AWNING, & PICTURE WINDOW
VCSMT VISTALUXE CASEMENT, AWNING, & PICTURE WINDOW INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING ANY INSTALLATION Kolbe & Kolbe Millwork, Co., Inc. 1323 S. 11th Ave. -
More information