16 STEEL CABINET HEAVY DUTY

Size: px

Start display at page:

Download "16 STEEL CABINET HEAVY DUTY"

Allan Gray
5 years ago
Views:

1 HEAVY DUTY 16 STEEL CABINET ASSEMBLY INSTRUCTIONS SIX DRAWER BASE CABINET

Parts List Part No Description Qty Image SIX DRAWER

Cabinet Body 1 SLD-01 20 inch Full Extend Slides 16

2 DW-90 Small Drawer AP-DW Full Length Handles 6

Together KEY-001 Keys 2 6 mm Hex Nut LINER Drawer

2 Parts List Part No Description Qty Image SIX DRAWER BASE CABINET Part No Description Qty Image SB-1 Cabinet Body 1 SLD inch Full Extend Slides 16 DW-180 Large Drawer 2 Handle Screws Screws Washers 2 2 DW-90 Small Drawer AP-DW Full Length Handles 6 LK-001 Lock 1 M6-20 Hex Bolt for Connecting Cabinets Together KEY-001 Keys 2 6 mm Hex Nut LINER Drawer Liner 6 25 mm 1 inch Fender Washer 50 mm 2 inch Drywall Screw Page 2

3 Hardware 6MM Nuts M6-20 Bolts Large Washers Wood Screws 2 Handle Screws 2 Handle Washers 6 Aluminum Drawer Pulls Lock & Keys Number 001 Page 3

TOOLS REQUIRED Phillips Screw Driver 10 mm Open End Wrench 10 mm Ratchet/Socket Tape Measure BEFORE YOU BEGIN: Thoroughly Clean the Assembly Area Remove Personal Items that Can Scratch the Cabinet

Open Cartons Carefully to Avoid Damaging Cabinet Panels Compare Carton Contents with Parts List Count Use the Shipping Cartons for the Assembly Surface - Do Not Assemble on Concrete If Using a

will make the drawers feel like they are locked. Place a flat head screwdriver between the side of the drawer and the side panel and Gently Pry. Drawer will pop open.

4 TOOLS REQUIRED Phillips Screw Driver 10 mm Open End Wrench 10 mm Ratchet/Socket Tape Measure BEFORE YOU BEGIN: Thoroughly Clean the Assembly Area Remove Personal Items that Can Scratch the Cabinet Finish - Watches, Belt, Rings, etc. Open Cartons Carefully to Avoid Damaging Cabinet Panels Compare Carton Contents with Parts List Count Use the Shipping Cartons for the Assembly Surface - Do Not Assemble on Concrete If Using a Cordless Drill for Assembly - Dial Drill Torque to a Low Setting STEP 1 - continued on next page Remove All Drawers From Cabinet - Important Note - Sometimes the rubber keepers on the drawer slides will make the drawers feel like they are locked. Place a flat head screwdriver between the side of the drawer and the side panel and Gently Pry. Drawer will pop open. Label and number each drawer (1 through 6) with masking tape. Open Top Drawer to fully extended position. Push down on Right Drawer Slide release levers and push slide bodies towards cabinet. Repeat the procedure on the Left Drawer Slides. If Drawer does not release from slide, reverse the procedure, pulling up on the right lever and pushing down on the left lever. Remove Drawer from slide and cabinet body. Repeat procedure for remaining 5 Drawers. Right Drawer Slide Push Down on Release Lever Note Lever Release May Be reversed Page

5 STEP 1 - continued Label Each Drawer Remove Drawers from Cabinet Body Page 5

6 STEP 2 Attach Aluminum Pulls securely to Drawer Face with Machine Screws. Repeat for all remaining drawers Aluminum Pull Parts Magnum 6 x Aluminum Pulls AP-DW 2 x Machine Screws 2 x Washers IMPORTANT NOTE Do Not Store Keys in Cabinet If keys are locked in cabinet after assembly, drawers can be opened by turning the cabinet upside down. This will release the slide locking mechanism and all drawers can be opened to retrieve keys. Once cabinet has been mounted to wall or loaded with tools do not store keys in the cabinet drawer. Page 6

7 STEP 3 Move cabinet into its final position. Fasten cabinet to wall STUDS and/or adjacent cabinets as required. Adjacent Cabinet Mount Parts x M6-20 Hex Head Bolts x 6 mm Hex Nuts Wall Mount Parts x Drywall Screws x Fender Washers STEP Insert large drawers into cabinet body by extending all slides. Insert the Drawer Slides into these extended slides. Push drawer inward in a gentle rocking motion. When slides are properly inserted you will hear a clicking sound. Close and re-open drawer. Drawer should slide freely. If drawer binds, one or more slides was probably not correctly aligned during drawer insertion. NEVER FORCE SLIDES Installing drawers with double slides can be tricky. If you encounter resistance, check alignment and repeat above instructions. In some cases it may be easier to first attach the 2 left slides and then attach the 2 right slides. Slides are released by pulling the two plastic levers up or down. If slides are forced, the race that holds the ball bearing may become bent causing dislodged ball bearings. Loose ball bearings can be set back into the race and the race can be straightened using a small flat tipped screwdriver. Page 7

CARE AND CLEANING ONLY USE A WATER BASED CLEANING SOLUTION TO WIPE DOWN CABINET SURFACES DO NOT USE SOLVENTS AS THEY MAY DAMAGE THE CABINET FINISH OPTIONAL LEGS IMPORTANT NOTE Do not slide cabinet

8 CARE AND CLEANING ONLY USE A WATER BASED CLEANING SOLUTION TO WIPE DOWN CABINET SURFACES DO NOT USE SOLVENTS AS THEY MAY DAMAGE THE CABINET FINISH OPTIONAL LEGS IMPORTANT NOTE Do not slide cabinet into position with full weight on legs, the shear force may break or damage the leg. Lift cabinet and set into position. Adjustment Range Leg Mount Parts x Metal Screws WARRANTY INFORMATION WARRANTY: Cabinets are warranted to be free from defects in material and workmanship for 12 months from the date of the original purchase, with proof of purchase by the original purchaser. In the event we deem the product to be defective, Cabinet vendor will be responsible for replacement of the defective part ONLY. No cost for labor or installation will be reimbursed. Damages due to shipping and handling, improper installation, abuses (intentional or accidental) or normal wear and tear are NOT covered by this warranty. There are no other guarantees or warranties, implied or expressed, beyond the terms of this expressed written warranty. ALL PRICES, DESIGNS, MATERIAL AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Page 8

9 CABINET WALL MOUNTING All cabinet models have be designed and structurally reinforced for Wall Mounting. Cabinets elevated above the floor allow easy cleaning and access underneath. In addition to a more professional look and finish, wall mounting eliminates the dust balls around the legs and the inevitable rusting on the leg leveling threads. We recommend that the rear of the cabinets rest on a back support of either an existing protruding foundation stem wall or on a dimensional 2 x 6 or 2 x fastened to the wall (see below). Approximately 70% of the cabinet load will travel straight down the wall onto the back support and the balance of the load is cantilevered forward. The back support removes most of the load/force on the drywall screws used to fasten cabinets to the wall studs. The back support also makes install much faster and allows for easier alignment when bolting adjacent cabinets together. Page 9

HEAVY DUTY 11 STEEL CABINET

HEAVY DUTY 11 STEEL CABINET HEAVY DUTY STEEL CABINET ASSEMBLY INSTRUCTIONS ONE DRAWER BASE CABINET 05-206 Parts List Part No Description Qty Image ONE DRAWER BASE CABINET Part No Description Qty Image SB- Cabinet Body EH-0 Euro Hinge