Installation and Assembly - Vision Point LCD Screen Pedestal Stand - 75/100 mm Adapter Plate

Transcription

1 Installation and ssembly - Vision Point CD Screen Pedestal Stand - 75/100 mm dapter Plate Model: CS 100, CS 100S Read instruction sheet before you start installation and assembly. Maximum oad Capacity: 25 lb (11.3 kg) - freestanding when feet are in outward position 40 lb (18.1 kg) - bolted down to floor with screens over 25 lb or when feet are moved inwards 1 of 6

2 Parts ist Description Qty. CS 100 CS100S base foot weldment B main base weldment C 75/100 mm CD mount weldment D main support tube E mating base tube angled support tube G M4 x.7 x 10 mm phillips screw H M4 x.7 x 12 mm phillips screw I M4 x.7 x 20 mm phillips screw J concrete anchor x 1/4" set screw #14 x 1-1/4" wood screw M.375 x.5 x.38 retaining spacer N.198 x.313 x.437 retaining spacer O 3/32" hex wrench Note: ctual parts may appear slightly different than illustrated. IMPORTNT: This product is designed to accommodate CD screens with a VES 75 or VES 100 compliant mounting hole pattern. B C D E J G H I M N O 2 of 6

3 WRNING If base foot weldments () are positioned all the way outward, the Pedestal Stand can support up to a 25 lb (11.3 kg) CD screen without being bolted down to the floor. If the base foot weldments () are positioned inward along the base and/or the screen weighs more than 25 lb, the Pedestal Stand MUST be bolted down to the floor. Slide base foot weldments () into desired position on main base weldment (B) as shown below. Make sure upper tube is perfectly perpendicular with floor. ttach using four set screws () as shown below. Place cord management hole either in the back or in the front as required by your application. ront B Back Cord management hole Installation to Concrete loors Use base foot weldments () as a template to mark holes. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 1-1/4" (32 mm). Insert four anchors (J) in holes flush with floor as in igure 1. Place four retaining spacers (M) over anchors (J) as in igure 2. Place base foot weldments () over retaining spacers (M) and secure with four #14 x 11/ 4" wood screws () as in igure 3. WRNING Tighten wood screws so that base foot weldments are firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in lb (9 N.M.). 1 Drill holes and 2 Place retaining 3 insert anchors spacers and base foot weldments over concrete anchors and insert wood screws Tighten screws M J M J 3 of 6

4 Installation To Wood loors Use a stud finder to find centers of floor joists. Use base foot weldments () as a template to mark holes. Drill four 3/16" (5 mm) dia. holes to a minimum depth of 1-1/4" (32 mm). Place four retaining spacers (M) over holes. Place base foot weldments () over retaining spacers (M) and secure with four #14 x 1-1/4" wood screws (). M Insert half of mating base tube (E) into main base weldment (B) and attach using two set screws (). Slide main support tube (D) onto mating base tube (E) and attach using two set screws (). E D B E 4 of 6

5 Insert angled support tube () into main support tube (D) in orientation shown. djust support tube () to the desired height. IMPORTNT: In the highest position, the support tube () must be inserted at least 3-1/2" in the support tube (D). ttach using two 1/4" set screws (). D CORRECT INCORRECT Slide CD mount weldment (C) onto angled support tube (). djust viewing angle by swiveling CD mount weldment around support tube. WRNING ffix CD mount weldment (C) to support tube () using two 1/4" set screws (). CD Mount weldment (C) can be swiveled only up to 90 on each side. DO NOT position CD mount weldment (C) past 90 on either side. This will cause the installation to be unstable and may result in a hazardous installation. C C Swivel only up to 90 either way TOP VIEW 5 of 6

6 Run cords through cord management holes as shown. cord management hole cord management hole This product is designed to accommodate screens with VES 75 or 100 compliant hole pattern. or safe mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts. OR VES 75 MOUNTING PTTERN: 1.) Choose hole pattern indicated below. 2.) ttach CD mount weldment (C) to back of screen using four 10 mm screws (G) as indicated below. 3.) If hole pattern is in a pocket, attach CD mount weldment (C) to back of screen using four 20 mm screws (I) and four retaining spacers (N) as indicated below. OR VES 100 MOUNTING PTTERN: 1.) Choose hole pattern indicated below. 2.) ttach CD mount weldment (C) to back of monitor using four M4 x 10 mm screws (G) as indicated below. Note: If installing CD screen model Sharp C-13E1U, C-15E1U, C-20E1U, or if you don't get three complete turns in the screen inserts, use four M4 x 12 mm screws (H) instead of four M4 x 10 mm screws (G). or screens with a hole pattern in a pocket, spacers (N) go between adapter bracket () and screen. Screen may appear slightly different than illustrated. 6 of Peerless Industries, Inc. ll rights reserved. Peerless is a registered trademark and Vision Point is a trademark of Peerless Industries, Inc. ll other brand and product names are trademarks or registered trademarks of their respective owners.