YSD 600 T/TH Sliding Door System Installation Manual

Size: px
Start display at page:

Download "YSD 600 T/TH Sliding Door System Installation Manual"

Transcription

1 System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America.

2

3 TABLE OF CONTENTS Installation Notes Page ii & iii PARTS DESCRIPTION Framing Members Page 1 & 2 Accessories Page 2 to 4 ASSEMBLE DOOR PANELS Install Glazing Gaskets for Non-Impact & Small Missile Page 5 Install Glazing Spacers & Side Blocks for Large Missile Page 6 Glazing Sliding Panels Page 7 to 9 Apply Structural Silicone for Large Missile Page 9 ASSEMBLE SLIDING DOOR FRAME Assemble Sliding Door Frame Page 10 Seal Sliding Door Frame Page 11 INSTALL SLIDING DOOR FRAME Anchor Sliding Door Frame Page 12 Apply Perimeter Sealant Page 13 INSTALL DOOR PANELS Install Fixed Panels Page 14 to 16 Attach Fixed Panel Sill & Head Fillers Page 17 Install Sliding Panels Page 18 Adjust Sliding Panels Page 19 INSTALL VERTICAL SCREEN TRACKS Page 20 CALCULATING GLASS SIZES Page 21 SIZE LIMITATIONS Page 22 Page-i

4 INSTALLATION NOTES 1. Do not drop, roll or drag boxes of aluminum framing. Move and stack boxes with proper support to prevent distortion. If fork lifts are used, be especially careful about striking the boxes when lifting or moving. 2. Store in a dry, limited access area. If rain exposure, condensation or any water contact is likely, then all packaging material should be removed. Wet packaging materials may permanently discolor or stain aluminum finishes and paints. 3. All materials should be checked for quantity and quality upon receipt, YKK AP must be notified immediately of any discrepancies in shipment. Check to make sure that you have the required shims, sealants, supplies, and tools necessary for the installation. 4. Carefully check the openings and surrounding conditions that will receive your material. If the construction is not per the construction documents, it is your responsibility to notify the general contractor in writing. Any discrepancies must be brought to the general contractor s attention before you proceed with the installation. 5. Collect your shop drawings, materials, packing list, and this installation manual. Carefully review parts location and the sequence of installation, including glazing and sealing. Installation instructions are of a general nature and may not cover every condition you will encounter. The shop drawings and/or installation manuals were prepared specifically for the product. 6. Any material substitutions must be of equal or greater quality. 7. Make certain that material samples have been sent for compatibility testing for all manufacturer s sealants involved. Make certain that sealants have been installed in strict accordance with the manufacturer s recommendations and specifications. 8. Consult sealant manufacture for proper sealant and backer rod selection. 9. Remember to isolate, in a approved manner, all aluminum from uncured masonry or other incompatible materials. 10. System-to-structure fasteners are not supplied by YKK AP. Fasteners called out on shop drawings are to indicate minimum sizes for design loading. 11. If any questions arise concerning YKK AP products or their installation, contact YKK AP Technical Center for clarification before proceeding. Page-ii

5 INSTALLATION NOTES 12. YKK AP sliding door installation is typically completed before drywall, flooring and other products have been completely installed. Take the extra time to wrap and protect the installed material. 13. YKK AP Model YSD 600 T/TH sliding doors are prefinished and prefabricated, sometimes preassembled, and must be protected against damage. 14. Concrete, mortar, plaster, muriatic acid and other alkaline and acid based construction and cleaning materials may be very harmful to finishes and should be removed with water and mild soap immediately or permanent damage or staining of the finishes will occur. A spot test is recommended before any cleaning agent is used. Abrasive type cleaners must never be used. 15. All work must start from, and be referenced to benchmarks, offset lines and/or column centerlines established by the architectural drawings and the general contractor. 16. All doors must be installed plumb, square, level, and true, and in accordance with approved shop drawings and these installation instructions. 17. Glass and glazing building codes governing the design and use of products vary widely. YKK AP America Inc. does not control the selection of products, product configurations, operating hardware and function, or glazing materials, and YKK AP assumes no responsibility for these design considerations. It is the responsibility of the design professional, owner, architect, specifier, general contractor, and the installer to make these selections in strict accordance with all applicable codes. 18. Check our website, for the latest installation manual update prior to commencing work. Page-iii

6

7 YSD 600 T/TH FRAMING MEMBERS Head BE Exterior Interlock Stile E Sill BE Head Adaptor/Filler For Sliding Panel E Fixed Jamb BE Sill Adaptor/Filler For Sliding Panel E Lock Jamb BE Head Adaptor/Reinforcement E Top/Bottom Rail BE Head Adaptor For Fixed Panel E Fixed Stile BE Vertical Screen Track E Lock Stile BE Screen Track Base E Interior Interlock Stile BE Lock Meeting Stile For OXO BE Fixed Bottom Rail BE Lock Meeting Stile Cover For OXO E Page-1

8 YSD 600 T/TH FRAMING MEMBERS Lock Meeting Stile BE Aluminum Reinforcement For Lock Meeting Stile BE E9-6293* Latch Meeting Stile BE Aluminum Reinforcement For Interior Interlock Stile BE E9-6294* YSD 600 TH ACCESSORIES Track Cover Stainless Steel E1-1601* Reinforcement Clip For OXXO Lock Stile E1-1628* Lock Strike/Keeper E1-1618* Reinforcement Clip For OXXO Latch Stile E1-1629* Ball Bearing Rollers Stainless Steel E1-1620* Setting Block For Non-Impact & Small Missile Panels E Fixed Panel Stopper Attach at Head E Setting/Side Block For Large Missile Panels E Sliding Guide E1-1625* Side Block For Large Missile Panels E Fixed Panel Anchor Clip Attach at Sill E Airtight Gasket For Frame Head & Sill E2-0051* Lock Strike/Keeper For OXXO E1-1627* Pile Weathering E2-0712* * Parts assembled to door/frame at the factory. Page-2

9 YSD 600 T/TH ACCESSORIES Wedge Gasket For Securing Fixed Panel to Frame E Dia. Plastic Rivet E3-1165* Exterior Glazing Gasket For Glazing Large Missile Panels E Screw Cap K Interior Glazing Spacer For Glazing Large Missile Panels, 3/8 F. C. E Recessed Pull Handle 3K1-1234* Meeting Stile Gasket For OXXO Sliding Panels E2-0740* Thumbturn Cylinder H-4204* Panel Glazing Gasket For Non-Impact & Small Missile 1 Insulated Glazing E Cylinder Trim Ring For Thumbturn Cylinder P-48530* Panel Glazing Gasket For Non-Impact & Small Missile 1-3/16 Insulated Glazing E MS Lock Hookbolt 1-1/2 Backset P-2101-SS* Jamb Bumper E2-0705* Face Plate For Hookbolt Lock P-33118* Head/Sill Bumper E2-0709* #8 32 x 1/2 Type F FHTCS, Stainless Steel For Attachment of Bottom Block E FF SS* Anti-Lift Block E3-1162* #8 x 3/8 Type AB PHSMS, Stainless Steel For Attachment of Screen Track PC SS* Shim For Anti-Lift Block E3-1164* #8 32 x 1/2 Type F PHTCS, Stainless Steel For Attachment of Ball Bearing Roller E PF SS* * Parts assembled to door/frame at the factory. Page-3

10 YSD 600 T/TH ACCESSORIES #8 32 x 1 Type F PHTCS, Stainless Steel For Attachment of Anti-Lift Block at Head PF SS* #12 x 1 Type AB PHSMS, Stainless Steel For Attaching E & E Reinforc. Clips PC SS #8 32 x 3/8 FHMS Stainless Steel For Attachment of Sliding Guide & Face Plate UM SS* #12 x 1-1/4 Type AB PHSMS, Stainless Steel For Frame & Panel Assembly PC SS #10 32 x 2-1/2 FHMS For Attachment of MS Lock to Lock Stile FN SS* #12 x 1-1/2 Type AB PHSMS, Stainless Steel For Attaching E Reinforcement Clip PC SS #10 x 1-1/4 Type AB PHSMS, Stainless Steel For Attachment of Head & Sill Bumpers E PC SS* #12 24 x 1-1/4 Type F PHTCS, Stainless Steel For Attachment of Strike PF SS* #10 32 x 1/2 Type F PHTCS, Stainless Steel For Attachment of Head Adaptors & Panel Stopper PF SS* #14 x 3/4 Type AB PHSMS, Stainless Steel For Anchor Clip E to Sill Attachment PC SS #10 24 x 3/4 Type F PHTCS, Stainless Steel For Attachment of Jamb Bumper E PF SS* #14 x 1/2 PHSMS Stainless Steel, For Meeting Stile to Anchor Clip E Attachment PM SS #10 x 5/8 PHTS (Tek) Stainless Steel For Attachment of Aluminum Reinforcing PS SS* * Parts assembled to door/frame at the factory. Page-4

11 ASSEMBLE SLIDING& FIXED PANELS STEP 1A INSTALL GLAZING GASKETS (NON-IMPACT & SMALL MISSILE PANELS ONLY) -Lay glass on flat surface with access to all four edges (i.e. lay glass on sawhorses). -Locate the roll of gasket supplied with the sliding door package. -Add up the united inches of the glass size for each lite of glass: (2 x Width) + (2 x Height) Ex.: A unit 34 wide by 76 tall would have 220 united. -Cut the gasket to the length determined above for each lite plus 6. -Begin by installing the gasket at the center of the top of each lite. See Detail 1. -Cut the gasket 1/2 away from the corner. -Cut the gasket squarely. Caution: Do not cut through the trim lip of the gasket. See DETAIL 2. Detail 1 Detail 2 -Wrap the gasket around the corner and install the gasket around the glass moving down the side of the lite. See DETAIL 3. -Cut the gasket 1/2 away from the next corner. -Proceed around the lite repeating the steps called out above. -Trim off the excess gasket at the end and butt the ends of the gasket against each other, allowing an extra 1/4 to ensure a tight fit. See DETAIL 4. Detail 3 Detail 4 Page-5

12 ASSEMBLE SLIDING& FIXED PANELS STEP 1B INSTALL GLAZING SPACERS & SIDE BLOCKS (LARGE MISSILE PANELS ONLY) Large missile panels require the installation of glazing tape, E2-0744, prior to assembling the panel members. -Cut top/bottom rail glazing tape to the Panel Daylight Opening Width. -Cut stile glazing tape to the Panel Daylight Opening Height plus(+) 1-1/2 (3/4 at each end). -Remove the protective backing from the glazing tape and apply it as shown below. Be careful not to stretch the tape when installing it. See Detail 5. Panel D.L.O. Height E Panel D.L.O. Width Detail 5 Fixed Panel Shown Sliding Panel Similar Fixed Stile E Glazing Spacer Bottom Rail 3/4 Large missile sliding panels also require the installation of side blocks, E for fixed and lock stiles and E for interlock and meeting stiles. -Remove the protective backing from the side blocks, apply sealant to the backs of the blocks, and install them at the 1/4 points of the panel daylight opening as shown below. See Detail 6. E E E E E Fixed Stile Lock Stile Interlock Stile Detail 6 Interlock Stile Page-6

13 ASSEMBLE SLIDING& FIXED PANELS STEP 2 GLAZING SLIDING PANELS (FOR ALL PANELS) -Just prior to assembling the panels apply and tool sealant to the glass corners behind the gasket on both sides. See Detail 7. -Carefully lay the lite of glass down onto a pair of sawhorses. -Apply sealant to the notched out ends of the top and bottom rails. -Install setting blocks, E for small missile or E for large missile, along the bottom rail glazing pocket at 1/4 points or according to engineering calculations. -Insert the top and bottom rails centered on the lite of glass with the exterior side of the panel facing up. -Align the stiles (exterior sides facing up) with the rails and attach them using a rubber mallet. Make sure all glazing gaskets or spacers are properly aligned. -Fasten each corner of the sliding panel with two PC-1220-SS fasteners. -Tool and wipe away excess sealant at the joints. -Install screw caps, K3-3004, into the clear holes at the top and bottom of the fixed and lock stiles. Detail 7 Note: The middle hole at the bottom is left unplugged for adjustment of the rollers. Screw caps for interlock & lock meeting stiles can only be installed after the head and sill fillers are attached. See Detail 8. Detail 8 Non-Impact Sliding Panel Shown Others Similar Page-7

14 ASSEMBLE SLIDING& FIXED PANELS STEP 2 (Continued) GLAZING SLIDING PANELS (FOR ALL PANELS) Seal Exterior Panel Joints -Apply sealant to the exterior joints between the rails and stiles at both the top and bottom of the assembled panels. -Tool the sealant to ensure a watertight seal. See Details 9 & 10. Apply & Tool Sealant Apply & Tool Sealant Detail 9 Sliding Panel Shown Detail 10 Fixed Panel Shown FOR ALL SMALL MISSILE & NON-IMPACT PANELS Sliding Panel -Apply and tool sealant to the joint between the marine gasket and panel corners. Seal at each corner and on both sides of the panel. See Detail 11. Apply & Tool Sealant Detail 11 Page-8

15 ASSEMBLE SLIDING& FIXED PANELS STEP 2 B GLAZING SLIDING PANELS (FOR ALL LARGE MISSILE PANELS) Install Glazing Gaskets -Cut horizontal & vertical glazing gaskets to Panel Daylight Opening plus (+) 3/16 for each foot of length. -Install the vertical glazing gaskets first then the horizontal gaskets. -Insert the gasket at each end. Then insert the gasket at the midpoint of the opening and push the remainder of gasket in working towards each end. See Detail 12. Vertical Glazing Gasket Horizontal Glazing Gasket Detail 12 Apply Interior Structural Silicone Sealant -Carefully turn over the assembled sliding panel so that the interior of the panel is facing up. Rest the frame on the sawhorses allowing the weight of the glass to compress the push-in wedge gaskets. -Make sure that all silicone contact surfaces and joints have been cleaned with isopropyl alcohol (50%) and lint free cloths using the two cloth method. -Apply masking tape to the aluminum and glass as shown. -Apply structural silicone sealant into the cavity between the panel and glass. Exert positive pressure so that the sealant completely fills the cavity. -Using a spatula or other non-scratching implement, immediately tool the sealant after running the joint. Exert positive pressure while tooling to ensure that the sealant makes positive contact with all surfaces. Be careful not to remove too much sealant! -Remove the masking tape within ten minutes of tooling. E E Masking Tape Structural Silicone E Do not allow the sealant to skin over! See Detail 13. Detail 13 Page-9

16 STEP 3 ASSEMBLE SLIDING DOOR FRAME ASSEMBLE SLIDING DOOR FRAME -Lay out members and locate fastener locations. -Apply (butter) sealant to each end of the jamb members. -Attach the jamb members to the head and sill with PC-1220-SS fasteners as shown. -Tool and wipe away any excess sealant at the joints. -Seal all exposed fastener heads with sealant. Also seal all unsealed fasteners ends. See Details 14 & 15. HEAD PC-1220-SS Sealant FIXED JAMB LOCK JAMB Detail 15 BE Fixed Jamb BE Lock Jamb SILL Detail 14 Apply Sealant to Mullion Ends Page-10

17 STEP 4 SEAL SLIDING DOOR FRAME ASSEMBLE SLIDING DOOR FRAME -Apply additional sealant to the head/jamb and sill/jamb joints along the inner and outer pockets. -Tool the sealant to ensure a watertight seal. See Detail 16. -At the exterior frame corners, apply and tool additional sealant to the spaces between the legs of the head and sill and the jamb. See Detail 17A & 17B. -At the interior frame corners, apply and tool additional sealant to the spaces between the jamb and the back leg of the head and sill. See Detail 17C. Apply & Tool Sealant Detail 16 Apply & Tool Sealant A Detail 17 Lock Jamb Shown Fixed Jamb Similar Apply & Tool Sealant C Apply & Tool Sealant B Fixed Jamb Shown Lock Jamb Similar Lock Jamb Shown Fixed Jamb Similar Page-11

18 STEP 5 ANCHOR SLIDING DOOR FRAME INSTALL SLIDING DOOR FRAME -The sliding door frame must be installed on a flat, level surface. -Check the rough opening for squareness and plumb at both ends. Also, make sure that appropriate space (3/8 nominal) has been allowed for shim at the head and both jambs. 1 3/8 Rough Opening Width (R.O.W.) Frame Width = R.O.W. 3/4 3/8 3/8 1 3 Rough Opening Height (R.O.H.) Frame Height = R.O.H. 3/8 3 Anchor Fastener Size & Location Per Approved Shop Drawings or Calculations Detail 18 2 Sealant -Set the assembled frame in the prepared opening on a bed of sealant. -Temporarily attach the frame to the structure using clamps and/or rope. -Field drill the head, sill, and jambs for anchor fasteners according to approved shop drawings or engineering calculations. Consult YKK AP if load requirements are in question. -Shim the head and jambs as needed; the frame must be level, plumb, and true. -Anchor the frame to the structure using appropriate anchor fasteners. -Seal all exposed anchor fastener heads at the sill on the sliding panel side. See Detail 18. Page-12

19 STEP 6 APPLY PERIMETER SEALANT INSTALL SLIDING DOOR FRAME -Install backer rod between the frame head and jambs and the structure. -Apply masking tape to the frame where sealant is applied. -Apply a quality perimeter sealant at the head and jambs. -Immediately tool the sealant to ensure watertight seal and remove the masking tape while the sealant is still wet. Note: Perimeter sealant must be applied to both the exterior and interior of the frame. -Apply a toe bead at the exterior of the sill and a heel bead at the interior. -Tool the sealant into the perimeter sealant to create a watertight seal. See Detail 19. HEAD Backer Rod & Sealant Backer Rod & Sealant Detail 19 JAMB Toe Bead Heel Bead SILL Page-13

20 INSTALL DOOR PANELS STEP 7 INSTALL FIXED PANELS -Prior to installing the fixed panel, attach anchor clip E to the fixed panel meeting stile with two(2) PM-1408-SS fasteners. -Apply sealant to the sill where the holes are pre-drilled for the anchor clip. See Detail 20. -Set the fixed panel into the frame and move it over tight against the fixed jamb. Make sure that the sill anchor clip holes align with the predrilled holes in the sill. See Detail 21. -Position the fixed panel stopper, E1-1624, tight against the fixed panel and aligned with the pre-drilled hole in the frame head. -Attach E to the frame head with one PF-1008-SS fastener. See Detail 22. Apply Sealant Detail 20 Meeting Stile PM-1408-SS E Head E PF-1008-SS Meeting Stile Detail 21 Detail 22 Page-14

21 STEP 7 (Continued) INSTALL FIXED PANELS INSTALL DOOR PANELS -Secure the panel anchor clip, E1-1626, to the sill with two PC-1412-SS fasteners. -Tool the excess sealant around the anchor clip. See Detail 23. Meeting Stile PC-1412-SS E Install Fixed Panel Head Adaptor E Position the head adaptor E at the head between the jamb and the interlock stile. Make sure that the head adaptor is flat against the head and the head adaptor attachment leg sits in the head reglet properly. See Detail 24. Sill Detail 23 Tool Sealant -Transfer hole locations from the pre-drilled clear holes on the head adaptor to the frame head. -Remove the head adaptor and drill dia. (#20 bit) holes at each location. -Apply sealant to the top of the head adaptor around the clear hole areas. -Attach the head adaptor E to the frame head using PF-1008-SS fasteners. See Detail 25. Detail 24 Sealant Match Drill Dia. BE BE PF-1008-SS E BE Apply Sealant E BE Detail 25 Fixed Panel Page-15

22 INSTALL DOOR PANELS STEP 7 (Continued) INSTALL FIXED PANELS -Cut vertical gaskets, E2-0671, to the Panel Height plus (+)1/4 per foot. -Cut horizontal gaskets, E2-0671, to the Panel Width plus (+) 1/4 per foot. -Lubricate the gaskets with a liberal amount of water or alcohol to facilitate the installation. -Install the vertical gaskets where the fixed panel stile meets the fixed jamb first. -Then install the horizontal gaskets where the fixed panel top rail meets the head adaptor E Insert the gasket into the reglet at each end. -Push in the rest of the gasket starting from the middle and work towards each end. Detail 25 See Detail 25. -At the head and sill, fill the cavity between the fixed panel and fixed jamb with sealant, continue to end of sill. -Tool the sealant to ensure a watertight seal. See Detail 26. Detail 26 Sill Shown, Head Similar Page-16

23 INSTALL DOOR PANELS STEP 8 ATTACH SLIDING PANEL HEAD & SILL FILLERS -Just prior to attaching sliding panel head & sill fillers, apply and tool sealant to the joint between the sill back leg and the interlock or lock meeting (OXO only) stiles. Also, apply a 6 bead of sealant at each end along the back leg of the sill. See Detail 27. Detail 28 Detail 27 -Insert the front leg of the head and sill fillers into the filler reglets and rotate the fillers into place as shown. See Detail 28. Note: Head and sill fillers must snap to ensure positive engagement. If it is difficult to snap in the fillers, you may have to puncture (pinhole) the sill/head bulb gasket to let out excess air. Detail 29 Sill Shown Head Similar -Once the head and sill fillers are installed apply and tool sealant to the joint where the fillers meet the lock jamb and interlock or meeting stiles. -Also apply and tool sealant where the head and sill filler weatherstrip meets the stile weatherstrip. -Insert screw caps, K3-3004, into the exposed clear holes on the stile. See Detail 29. Page-17

24 INSTALL DOOR PANELS STEP 9 INSTALL SLIDING PANELS -Remove the one anti-lift block from the fixed side of the sliding door. -Lift the sliding panel(s) up into the frame on the fixed panel side in order to clear the anti-lift blocks. -Carefully lower the panel(s) down onto the roller track. Make sure that the rollers are properly aligned with the roller track. -Slide the sliding panel back to the closed position and replace the anti-lift block previously removed. See Details 30 & 31. Caution: Do not allow the rollers to contact the floor before installing the sliding panels. Damage to the rollers may occur. Detail 30 E3-1162/E Anti-Lift Block (Fixed Side) E3-1162/E Anti-Lift Blocks (Sliding Side) Detail 31 OX Shown Others Similar Remove Before Installing Sliding Panel & Replace Once Installed Sliding Panel Must Be Positioned As Shown During Installation Page-18

25 INSTALL DOOR PANELS STEP 10 ADJUST SLIDING PANELS -Adjust the rollers of the sliding panel(s) through the access hole on each side so that the door is level and rolls freely: -Clockwise to raise panel. -Counterclockwise to lower panel. See Detail 32. Lower Detail 32 Raise If the Lock Does Not Operate Properly, Adjust the Lock Strike -Loosen the lock strike fasteners. -Adjust the lock strike on the frame so that the lock engages correctly. -Tighten the lock strike fasteners. Lock Jamb BE Lock Strike E See Detail 33. Detail 33 PF-1220-SS Page-19

26 STEP 11 (OPTIONAL) INSTALL VERTICAL SCREEN TRACKS INSTALL VERTICAL SCREEN TRACKS Head & sill screen tracks are integral to the YSD 600 TH sliding door frame. Vertical screen tracks consist of two extrusions: a track base (E9-4023) and a track (E9-6027). For OX/XO frames install the screen tracks at the fixed and lock jambs. For OXO frames install the screen tracks at the fixed jamb and lock meeting stile. For OXXO frames install the screen tracks at both fixed jambs. -To install screen tracks at jambs, position the track base on the jamb with the short leg end flush with the edge of the jamb. -To install screen tracks at the Lock Meeting Stiles (OXO), position the track base on the jamb with the short leg end 1 from the glass edge of the Lock Meeting Stile. Make sure the track base is straight and plumb. -Temporarily secure the track base and transfer the pre-drilled hole locations on it to the jamb. -Remove the track base and drill dia. (#28 bit) holes at each location. -Attach the track base to the jamb at each hole location with PC-0806 fasteners. -Place the screen track over the track base and align the pre-drilled holes on the screen track with the ones on the long leg of the track base. -Fasten the screen track to the track base with FC-0808 fasteners. See Detail 34. Detail 34 Page-20

27 CALCULATING GLASS SIZES CONFIGURATION GLASS WIDTH PANEL TYPE GLASS HEIGHT OX/XO FW/2 4 7 /8 FIXED (FH 7 3 /4 ) OXO FW/3 4 1 /4 SLIDING (FH 7 3 /4 ) OXXO FW/4 4 1 /8 Glass Bite = 5/8 FW (Frame Width) FW (Frame Width) OX / XO OXO FW (Frame Width) OXXO FH (Frame Height) FIXED PANEL FH (Frame Height) SLIDING PANEL Page-21

28 SLIDING DOOR SIZE LIMITATIONS CONFIGURATION Without Reinforcing Design Load +75/-75 PSF MAXIMUM FRAME SIZE* (AS TESTED) 10-3 x 8-0 O FIXED O FIXED O FIXED OX&XO X X OXO X X O FIXED O FIXED Without Reinforcing Design Load +100/-100 PSF With Reinforcing Design Load +120/-120 PSF Without Reinforcing Design Load +75/-75 PSF Without Reinforcing Design Load +100/-100 PSF With Reinforcing Design Load +120/-120 PSF Without Reinforcing Design Load +75/-75 PSF Without Reinforcing Design Load +100/-100 PSF 8-2 x x /2 x /2 x /2 x x x 8-0 OXXO With Reinforcing 16-3 x 8-0 Design Load +120/-120 PSF * If the height to width ratio exceeds 3:1, the sliding door must be reviewed by YKK AP engineering. NOTE: 3/8 Frame width and height should allow 3/4 for width & 3/8 for height overall clearance between the door frame and rough opening. This allows for thermal expansion and ease of installation. O FIXED X FRAME HEIGHT ROUGH OPENING 3/8 FRAME WIDTH ROUGH OPENING 3/8 FLOOR ELEV. Page-22

29

30 YKK AP America Inc The Bluffs Suite 100 Austell, Georgia

Installation Manual. YSD 600 T/TH Sliding Door. YSD 600 T/TH Sliding Door System

Installation Manual. YSD 600 T/TH Sliding Door. YSD 600 T/TH Sliding Door System YSD 600 T/TH Sliding Door System Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii & iii PARTS DESCRIPTION Framing

More information

YSD 400 Sliding Door System Installation Manual

YSD 400 Sliding Door System Installation Manual System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION

More information

YOW 225 TU Window System

YOW 225 TU Window System ThermaBond Plus Poured & Debridged Technology YOW 225 TU SYSTEM DESCRIPTION YOW 225 TU PERFORMANCE FEATURES 2-1/4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Casement, Projected

More information

YWE 40 T Window Wall System Installation Manual

YWE 40 T Window Wall System Installation Manual Installation Manual 2005 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................

More information

YES 600 Thermal Clip Storefront System Installation Manual

YES 600 Thermal Clip Storefront System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................

More information

YES 40 FS/FI Storefront System Installation Manual

YES 40 FS/FI Storefront System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 40 FS Framing Members... Page 1 YES 40

More information

YES 45 TU Thermal Storefront System Installation Manual

YES 45 TU Thermal Storefront System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION Framing

More information

YVS 400 TU Window System

YVS 400 TU Window System YVS 400 TU SYSTEM DESCRIPTION YVS 400 TU PERFORMANCE FEATURES 4 Overall Depth ThermaBond Plus Poured & Debridged Thermal Break Variations: Single Hung, Double Hung & Fixed Windows 1 /8 & 1 1 /16 Glazing

More information

YSG 40/50/50T Window Wall System Installation Manual

YSG 40/50/50T Window Wall System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION YSG 40

More information

INSTALLATION MANUAL STOREFRONT DOORS

INSTALLATION MANUAL STOREFRONT DOORS INSTALLATION MANUAL STOREFRONT DOORS www.aluflam-usa.com SYSTEM DESCRIPTION - Extruded and filled aluminum framing, tested and approved by UL - 3-3/8 frame depth - Clear, fire-rated safety glazing - Door

More information

Swing Door Installation Manual

Swing Door Installation Manual Manual 20D/35D/50D 20DH/35DH 40M/50M 25FD 35XT 50XT 01-4000-03 2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes.......................................

More information

YES 45 XT High Performance Thermal Storefront System

YES 45 XT High Performance Thermal Storefront System Dual Thermal Barrier ThermaBond Plus Pour & Debridge Technology Installation Manual 2015 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page

More information

YCW 752 Outside Glazed Curtain Wall System Installation Manual

YCW 752 Outside Glazed Curtain Wall System Installation Manual YCW 752 Outside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

YHC 300 SSG Structural Silicone Glazed Curtain Wall System Installation Manual

YHC 300 SSG Structural Silicone Glazed Curtain Wall System Installation Manual YHC 300 SSG Structural Silicone Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

YCW 750 IG Inside Glazed Curtain Wall System Installation Manual

YCW 750 IG Inside Glazed Curtain Wall System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YCW 750 IG Framing Members... Page 1 to 3

More information

YES 45 FS/FI Storefront System Installation Manual

YES 45 FS/FI Storefront System Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 45 FS Framing Members... Page 1 YES 45

More information

YOW 350 XT Thermally Broken Operable Window System

YOW 350 XT Thermally Broken Operable Window System YOW 350 XT Thermally Broken Operable Window System MegaTherm Glass Fiber With 6/6 Nylon Thermal Break YOW 350 XT SYSTEM DESCRIPTION 3-1/2 Overall Frame Depth MegaTherm Thermal Break Construction: Frame

More information

YHC 300 IG Inside Glazed Curtain Wall System Installation Manual

YHC 300 IG Inside Glazed Curtain Wall System Installation Manual YHC 300 IG Inside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL

DHS-500 IMPACT SYSTEM INSTALLATION MANUAL DHS-500 IMPACT SYSTEM INSTALLATION MANUAL TABLE OF CONTENTS SECTION PAGE GENERAL NOTES 3 EXTRUSION & PARTS IDENTIFICATION 4-5 DETERMINE FRAME SIZE 6 FABRICATE VERTICAL MULLIONS & FILLERS 7-8 FABRICATE

More information

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

YHS 50 TU Storefront System & Model 35H Door Installation Manual

YHS 50 TU Storefront System & Model 35H Door Installation Manual Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 TU Framing Members... Page 1 YHS 50

More information

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS 1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS MARCH, 2009 PART NUMBER 590-500 1 INSTALLATION INSTRUCTIONS 2 INDEX MARCH, 2009 INSTALLATION INSTRUCTIONS CONTENTS These instructions show the general installation sequence and procedure for typical installation.

More information

YHS 50 FS Storefront System & Model 35H/50H Door Installation Manual

YHS 50 FS Storefront System & Model 35H/50H Door Installation Manual Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YHS 50 Framing Members... Page 1 YHS 50 Accessories...

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.

More information

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING

INSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED

More information

Thermally Broken Framing and Door Installation

Thermally Broken Framing and Door Installation INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems

More information

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION

More information

Heavy Wall Applied Stop Tube Frame and Door Installation

Heavy Wall Applied Stop Tube Frame and Door Installation INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems

More information

FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE:

FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE: BuildingEnvelope R FG-5100T STORMMAX INSTALLATION AND GLAZING MANUAL NOTE: THE INSTALLATION DETAILS FOUND IN THIS PACKAGE ARE GENERIC AND ARE FOR REPRESENTATION ONLY WITH THE INTENT OF GIVING THE INSTALLATION

More information

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE PATIO DOORS INSTALLATION GUIDE These instructions cover general installation conditions. Improper installation could affect your doors operation and warranty. Deviations from these instructions should

More information

Vinyl Sliding Glass Door Assembly Instructions

Vinyl Sliding Glass Door Assembly Instructions Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS

More information

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls

More information

Storefront Installation Guide

Storefront Installation Guide Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation

More information

Series Sloped glazed Curtain wall. Installation Instructions

Series Sloped glazed Curtain wall. Installation Instructions Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End

More information

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS 2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed

More information

Series 7650 Installation Instructions Sliding Glass Door

Series 7650 Installation Instructions Sliding Glass Door Series 7650 Installation Instructions Sliding Glass Door Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration products are removed

More information

GENERAL INSTALLATION GUIDELINES

GENERAL INSTALLATION GUIDELINES 1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation

More information

Series Exterior glazed curtain wall. Installation Instructions

Series Exterior glazed curtain wall. Installation Instructions Series 5500 Exterior glazed curtain wall Installation Instructions Part NO. Y550 November 2016 TABLE OF CONTENTS SECTION S-5500 SCREW SPLINE CURTAIN WALL PAGE I. General Notes and Guidelines.. 3-4 II.

More information

GENERAL INSTALLATION GUIDELINES

GENERAL INSTALLATION GUIDELINES 1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation

More information

14000 I/O Series Flush Glaze. Fabrication and Installation Instructions

14000 I/O Series Flush Glaze. Fabrication and Installation Instructions 14000 I/O Series Flush Glaze Fabrication and Installation Instructions Last saved on 12/18/2009 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...4 ACCESSORIES...5 OVERVIEW...6

More information

ELEPHANT DOOR SYSTEMS SERIES E1200

ELEPHANT DOOR SYSTEMS SERIES E1200 INSTALLATION INSTRUCTIONS ELEPHANT DOOR SYSTEMS SERIES E1200 Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com AVDB3096 03.13 TABLE OF CONTENTS SUBJECT PAGE GENERAL INSTALLATION

More information

Please read and understand all instructions before beginning. These instructions cover the non-impact aluminum sliding glass door.

Please read and understand all instructions before beginning. These instructions cover the non-impact aluminum sliding glass door. The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand

More information

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation

More information

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS 3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure

More information

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4 VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7

More information

Series Advanced and alternate. Installation Instructions

Series Advanced and alternate. Installation Instructions Series 5500 Advanced and alternate Installation Instructions Part NO. Y557 February 2013 TABLE OF CONTENTS SECTION S-5500 ADVANCED INSTALLATION INSTUCTIONS PAGE I. General Notes and Guidelines...... 3-4

More information

Sun Control-Solar Eclipse-Solar Shelf

Sun Control-Solar Eclipse-Solar Shelf Sun Control-Solar Eclipse-Solar Shelf Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! TABLE OF CONTENTS GENERAL INFORMATION Product Use...Page 3 Protection and Storage...Page

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015 Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! May 2015 Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com S E R I E S 6 0 0 0 X T - S T O R E F R O N T I

More information

Pocket Door Installation Instructions

Pocket Door Installation Instructions Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code

More information

4-lite Patio Door. Installation Instructions

4-lite Patio Door. Installation Instructions 4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8

More information

SERIES 300 SINGLE HUNG WINDOW INSTALLATION

SERIES 300 SINGLE HUNG WINDOW INSTALLATION IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS

More information

Installation Instructions

Installation Instructions Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF

More information

Panel Assembly and Installation

Panel Assembly and Installation Assembly and Installation Assembly and Installation for Andersen 400 Series Frenchwood, 200 Series Narroline, 200 Series Perma-Shield Gliding Patio Doors and 400 Series Perma-Shield Gliding Patio Doors

More information

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions

More information

14000 Series. Fabrication and Installation Instructions

14000 Series. Fabrication and Installation Instructions 14000 Series Fabrication and Installation Instructions 14000 Series Revision December 01, 2009 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 4 ACCESSORIES... 7 OVERVIEW...

More information

SERIES 300 SINGLE HUNG WITH FIN WINDOW INSTALLATION

SERIES 300 SINGLE HUNG WITH FIN WINDOW INSTALLATION IMPORTANT INFORMATION: WHETHER IT BE LOCATION OR INSTALLATION TYPE, NOT ALL WINDOW TYPES CAN BE INSTALLED IN ALL AREAS OR WALL CONDITIONS. CONSULT YOUR LOCAL BUILDING CODE DEPARTMENT FOR ANY REGULATIONS

More information

14000 Series. Fabrication and Installation Instructions

14000 Series. Fabrication and Installation Instructions 14000 Series Fabrication and Installation Instructions Revision May 2013 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...5 ACCESSORIES...8 OVERVIEW...10 FRAME FABRICATION...15

More information

InstallatIon InstructIons for 2-lIte PatIo Door unassembled

InstallatIon InstructIons for 2-lIte PatIo Door unassembled InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone

More information

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration

More information

SERIES 4070-T GENERAL ASSEMBLY AND INSTALLATION INSTRUCTIONS

SERIES 4070-T GENERAL ASSEMBLY AND INSTALLATION INSTRUCTIONS Table of Contents I. Care and Maintenance... 2 II. Tools / Materials, Sealant Requirements, & Anchor Instructions... 2 III. Structure Verification & Sub-Sillpan Installation... 3 1. Opening Verification...3

More information

INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR

INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0292 HANDLING, STORAGE,

More information

Installation - Sub Cills

Installation - Sub Cills Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings

More information

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780

SLIDING GLASS DOOR ASSEMBLY INSTRUCTION Series 680/780 10/07 M0200030 GENERAL NOTICE READING THESE INSTRUCTIONS FIRST AND FOLLOWING THE PROCEDURES IN PROPER SEQUENCE WILL REDUCE FRUSTRATION, COSTLY MISTAKES AND WASTED TIME. Protect main frame only with light

More information

InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled

InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty

More information

INSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE

INSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;

More information

4500 Series. Fabrication and Installation Instructions

4500 Series. Fabrication and Installation Instructions 4500 Series Fabrication and Installation Instructions E4500 Series July, 2017 Table of Contents GENERAL CONSTRUCTION NOTES... 3 EXTRUDED ALUMINUM PARTS... 5 ACCESSORIES... 7 OVERVIEW... 8 FRAME FABRICATION...

More information

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay

More information

PIVOT DOOR 3400P INSTALLATION INSTRUCTIONS

PIVOT DOOR 3400P INSTALLATION INSTRUCTIONS Table of Contents I. Tools, Sealant Requirements, Anchor Recommended Table...1 II. Opening, Frame & Panel Verification...2-3 III. Frame Assembly...4 IV. Frame Installation...5-7 V. Glazing Instructions...8

More information

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

e-lite fabrication/assembly and Installation instructions

e-lite fabrication/assembly and Installation instructions e-lite fabrication/assembly and Installation instructions Part NO. YWLS February 2013 TABLE OF CONTENTS SECTION PAGE I. General Notes and Guidelines.. 3-4 II. E-Lite Stick Built Channel Base Assembly...

More information

INSTALLATION INSTRUCTIONS SERIES 487 CENTER GLAZED WITH 1-1/2" TRIM OFFICE PARTITIONS

INSTALLATION INSTRUCTIONS SERIES 487 CENTER GLAZED WITH 1-1/2 TRIM OFFICE PARTITIONS INSTALLATION INSTRUCTIONS SERIES 87 CENTER GLAZED WITH -/" TRIM OFFICE PARTITIONS Phone: (800) -6 Fax: (800) 58-7 crlaurence.com usalum.com crl-arch.com M056_Rev_D SERIES 87 OFFICE PARTITIONS CENTER GLAZED

More information

Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation. Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed

More information

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath

More information

Vinyl Windows and Doors

Vinyl Windows and Doors Vinyl Windows and Doors Manufactured by Pella Corporation Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. Part Number: V981555 2009 Pella Corporation

More information

SERIES 3070-T MULTI-SLIDE ASSEMBLY & INSTALLATION INSTRUCTIONS

SERIES 3070-T MULTI-SLIDE ASSEMBLY & INSTALLATION INSTRUCTIONS Table of Contents I. Care and Maintenance...2 II. Tools / Material & Sealant Requirements...2 III. Assembly and Installation...2 IV. Glazing Assembly...3 V. Panel Assembly...3 1. X Panel...3 2. O Panel...4

More information

Storefront Installation Guide INSTALLATION INSTRUCTIONS

Storefront Installation Guide INSTALLATION INSTRUCTIONS STOREFRONT General Notes 1. Check contract documents and shop drawings, and understand and clarify any Field Verify Notes, approvals of drawings, and products required to be familiar with the project.

More information

INSTALLATION INSTRUCTIONS TRIFAB 451UT SCREW SPLINE ASSEMBLY TRIFAB 451UT. AUGUST, 2010 (Part No. 452T-CG-970) EC

INSTALLATION INSTRUCTIONS TRIFAB 451UT SCREW SPLINE ASSEMBLY TRIFAB 451UT. AUGUST, 2010 (Part No. 452T-CG-970) EC AUGUST, 2010 (Part No. 452T-CG-970) EC 97904-31 1 INSTALLATION SCREW SPLINE ASSEMBLY Kawneer Company, Inc., 2010 INSTRUCTIONS 2 TABLE OF CONTENTS (452T-CG-970) AUGUST, 2010 These instructions show the

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! FEBRUARY 2012

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! FEBRUARY 2012 Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! Phone: 1-866-OLDCASTLE (653-2278) Web Address: www.oldcastlebe.com FG-1000 & FG-2000 INSTALLATION & GLAZING INSTRUCTIONS These

More information

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! OCTOBER Phone: OLDCASTLE ( ) Web Address:

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! OCTOBER Phone: OLDCASTLE ( ) Web Address: Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY! TABLE OF CONTENTS General Information............................. Page 2 4 Outside Glaze Non Thermal...............................Page

More information

Installation Guide for Architectural Wood Hinged Windows

Installation Guide for Architectural Wood Hinged Windows Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits

More information

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will

More information

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A 1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

CGI Series 560 SGD Installation Instructions

CGI Series 560 SGD Installation Instructions CGI Series 560 SGD Installation Instructions Read these instructions completely before beginning to install. Become familiar with what type of installation will be required. This door can be installed

More information

Mira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions

Mira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 900 SERIES RIBBON WINDOW INSTALLATION INSTRUCTIONS 3056 Walker Ridge Dr. NW, Suite G Walker, MI 49544 800-866-2227 November 2016 www.tubeliteinc.com Page 1 TABLE OF CONTENTS GENERAL CONSTRUCTION NOTES...3-4

More information

INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE

INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE INSTALLATION INSTRUCTIONS ENTICE SERIES PREMIUM ENTRANCE SYSTEM EXTERIOR GLAZE Phone: (800) 421-6144 Fax: (800) 582-7501 crlaurence.com usalum.com crl-arch.com 11M0230 HANDLING, STORAGE, AND PROTECTION

More information

Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.

Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.

More information

Installation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006

Installation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction

More information

40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)

40mm Thermoclick.  Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories

More information

6400, 8400 and 9400 Series Sliding Patio Door

6400, 8400 and 9400 Series Sliding Patio Door Contemporary 3 Panel Classic 5 Panel French Panel 6400, 8400 and 9400 Series Sliding Patio Door (O) Fixed Panel Left (X) Operating / Mullion Panel Right (X) Operating / Lock Panel Left (O) Fixed Panel

More information

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES

SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES INSTALLATION INSTRUCTIONS SERIES 900 TERRACE DOOR WITH TRANSOM AND SIDELITES Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0172_REV_A HANDLING, STORAGE, AND PROTECTION

More information

Installation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows

Installation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance

More information

INSTALLATION INSTRUCTIONS TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T

INSTALLATION INSTRUCTIONS TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T INSTALLATION TRIFAB VG SCREW SPLINE ASSEMBLY TRIFAB VG 450 TRIFAB VG 451 TRIFAB VG 451T INSTRUCTIONS LITHO IN U.S.A. JANUARY KAWNEER COMPANY, INC., 2004 451-VG-970.01.04a PART NO. 451-VG-970 1 INSTALLATION

More information

MULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION

MULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION MULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION TOOLS AND SUPPLIES 1 TOOLS CHECK LIST 1. laser level 2. hammer 3. pry bars 4. ladders 5. utility knife 6. screw gun 7. applicator foam gun 8. "j"

More information

Method of Build 1. General

Method of Build 1. General Method of Build 1 General GLAZED ELEVATIONS Viso Double Glazed in glazed form differs from many other systems as the vertical joints can have Viso dry joints or the unique HIDDEN mullion post between glazed

More information

INOVO 2-LITE SLIDING PATIO DOOR

INOVO 2-LITE SLIDING PATIO DOOR INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information